leds: Add shutdown gpio for is31fl32xx
Subsystems (2)
v2 cover leds: Add shutdown gpio for is31fl32xx
This patch series primarily adds the shutdown-gpios support for the IS31FL32xx controller.It also includes a fix and dt-bindings updates derived from previous attempts [1]. Patch 1 and patch 2 are based on a previous attempt [1]. The driver-related updates in patch 2 have already been merged. Patch 3 and Patch 4 add support for the shutdown-gpios property, which corresponds to the SDB pin of the IS31FL32xx series chips. This pin is used to enter and exit the hardware shutdown mode. Patch 5 fixes errors introduced by previous changes. It impacts the brightness control function of the IS31FL3236. [1] https://lore.kernel.org/linux-leds/[email protected]/
Changes in v2:
- Fix $id mismatch with file name in dt-binding.
- Link to v1: https://lore.kernel.org/linux-leds/[email protected]/
Jun Yan (5):
dt-bindings: leds: is31fl32xx: convert the binding to yaml
dt-bindings: leds: leds-is31fl32xx: add support for is31fl3236a
dt-bindings: leds: leds-is31fl32xx: Add shutdown-gpios property
leds: is31fl32xx: Add shutdown pin to exit hardware shutdown mode
leds: is31f132xx: Fix missing brightness_steps for is31f13236
.../bindings/leds/issl,is31fl32xx.yaml | 200 ++++++++++++++++++ .../bindings/leds/leds-is31fl32xx.txt | 53 ----- drivers/leds/leds-is31fl32xx.c | 7 + 3 files changed, 207 insertions(+), 53 deletions(-) create mode 100644 Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml delete mode 100644 Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt
Signature · 1 line
2.53.0
PATCH v2 1/5 dt-bindings: leds: is31fl32xx: convert the binding to yaml
Convert leds-is31fl32xx to DT schema format.
--- .../bindings/leds/issl,is31fl32xx.yaml | 163 ++++++++++++++++++ .../bindings/leds/leds-is31fl32xx.txt | 53 ------ 2 files changed, 163 insertions(+), 53 deletions(-) create mode 100644 Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml delete mode 100644 Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml new file +163 -0
@@ -0,0 +1,163 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/issl,is31fl32xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IS31FL32xx and Si-En SN32xx LED controller + +maintainers: + - Lucca Fachinetti <[email protected]> + - Pavel Machek <[email protected]> + - Jun Yan <[email protected]> + +description: | + The IS31FL32xx/SN32xx family of LED drivers are I2C devices with multiple + constant-current channels, each with independent 256-level PWM control. + Each LED is represented as a sub-node of the device. + + For more product information please see the links below: + https://www.lumissil.com/assets/pdf/core/IS31FL3216_DS.pdf + https://www.lumissil.com/assets/pdf/core/IS31FL3218_DS.pdf + https://www.lumissil.com/assets/pdf/core/IS31FL3235_DS.pdf + https://www.lumissil.com/assets/pdf/core/IS31FL3236_DS.pdf + https://www.lumissil.com/assets/pdf/core/IS31FL3293_DS.pdf + +properties: + compatible: + enum: + - issi,is31fl3216 + - issi,is31fl3218 + - issi,is31fl3235 + - issi,is31fl3236 + - issi,is31fl3293 + - si-en,sn3216 + - si-en,sn3218 + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^led@([1-9])+$": + type: object + $ref: common.yaml# + unevaluatedProperties: false + + properties: + reg: + description: + LED channel number (1..N) + minimum: 1 + maximum: 36 + + required: + - reg + +allOf: + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3293 + then: + patternProperties: + "^led@([1-9])+$": + properties: + reg: + maximum: 3 + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3216 + - si-en,sn3216 + then: + patternProperties: + "^led@([1-9])+$": + properties: + reg: + maximum: 16 + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3218 + - si-en,sn3218 + then: + patternProperties: + "^led@([1-9])+$": + properties: + reg: + maximum: 18 + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3235 + then: + patternProperties: + "^led@([1-9])+$": + properties: + reg: + maximum: 28 + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3236 + then: + patternProperties: + "^led@([1-9])+$": + properties: + reg: + maximum: 36 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/leds/common.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + led-controller@3c { + compatible = "issi,is31fl3236"; + reg = <0x3c>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_STATUS; + }; + + led@5 { + reg = <5>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_POWER; + linux,default-trigger = "default-on"; + }; + }; + }; +... +
Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt deleted +0 -53
53 lines not on this page · raw message
Signature · 1 line
2.53.0
PATCH v2 2/5 dt-bindings: leds: leds-is31fl32xx: add support for is31fl3236a
In reply to Jun YanAdd an additional and optional control property for setting the output PWM frequency to 22kHz that exists on is31fl3236a. The default is 3kHz and this option puts the operational frequency outside of the audible range.
--- .../bindings/leds/issl,is31fl32xx.yaml | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+)
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +25 -0
@@ -21,6 +21,7 @@ description: | https://www.lumissil.com/assets/pdf/core/IS31FL3218_DS.pdf https://www.lumissil.com/assets/pdf/core/IS31FL3235_DS.pdf https://www.lumissil.com/assets/pdf/core/IS31FL3236_DS.pdf + https://www.lumissil.com/assets/pdf/core/IS31FL3236A_DS.pdf https://www.lumissil.com/assets/pdf/core/IS31FL3293_DS.pdf properties:
@@ -30,6 +31,7 @@ properties: - issi,is31fl3218 - issi,is31fl3235 - issi,is31fl3236 + - issi,is31fl3236a - issi,is31fl3293 - si-en,sn3216 - si-en,sn3218
@@ -37,6 +39,12 @@ properties: reg: maxItems: 1 + issi,22khz-pwm: + type: boolean + description: + When present, the chip's PWM will operate at ~22kHz as opposed + to ~3kHz to move the operating frequency out of the audible range. + "#address-cells": const: 1
@@ -60,6 +68,22 @@ patternProperties: - reg allOf: + - if: + properties: + compatible: + contains: + enum: + - issi,is31fl3216 + - issi,is31fl3218 + - issi,is31fl3235 + - issi,is31fl3236 + - issi,is31fl3293 + - si-en,sn3216 + - si-en,sn3218 + then: + properties: + issi,22khz-pwm: false + - if: properties: compatible:
@@ -116,6 +140,7 @@ allOf: contains: enum: - issi,is31fl3236 + - issi,is31fl3236a then: patternProperties: "^led@([1-9])+$":
Signature · 1 line
2.53.0
PATCH v2 3/5 dt-bindings: leds: leds-is31fl32xx: Add shutdown-gpios property
In reply to Jun YanThe IS31FL32XX series features an SDB shutdown pin.
Driving it low (active low) places the chip into hardware shutdown mode for power saving, while all register contents are preserved and registers are not reset.
Add shutdown-gpios property to describe the GPIO connected to the SDB pin of IS31FL32XX series LED controllers.
--- .../devicetree/bindings/leds/issl,is31fl32xx.yaml | 12 ++++++++++++ 1 file changed, 12 insertions(+)
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +12 -0
@@ -45,6 +45,15 @@ properties: When present, the chip's PWM will operate at ~22kHz as opposed to ~3kHz to move the operating frequency out of the audible range. + shutdown-gpios: + maxItems: 1 + description: + GPIO connected to the chip's SDB pin. + Driving this GPIO low places the chip into hardware shutdown mode + for power saving. All register contents are preserved and registers + are not reset during shutdown. The chip exits hardware shutdown mode + when the SDB pin is pulled high. + "#address-cells": const: 1
@@ -158,6 +167,7 @@ additionalProperties: false examples: - | + #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/leds/common.h> i2c {
@@ -170,6 +180,8 @@ examples: #address-cells = <1>; #size-cells = <0>; + shutdown-gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + led@1 { reg = <1>; color = <LED_COLOR_ID_RED>;
Signature · 1 line
2.53.0
Re: [PATCH v2 3/5] dt-bindings: leds: leds-is31fl32xx: Add shutdown-gpios property
Quoted 18 lines · Jun Yan
The IS31FL32XX series features an SDB shutdown pin.
Driving it low (active low) places the chip into hardware shutdown mode for power saving, while all register contents are preserved and registers are not reset.Add shutdown-gpios property to describe the GPIO connected to the SDB pin of IS31FL32XX series LED controllers.
Signed-off-by Jun Yan <[email protected]>--- .../devicetree/bindings/leds/issl,is31fl32xx.yaml | 12 ++++++++++++ 1 file changed, 12 insertions(+)Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +0
-0
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml properties: · line 48
Quoted 4 lines
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +1
-0@@ -45,6 +45,15 @@ properties: When present, the chip's PWM will operate at ~22kHz as opposed to ~3kHz to move the operating frequency out of the audible range. + shutdown-gpios:
powerdown-gpios (see gpio-consumer-common)
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml properties: · line 49
Quoted 1 line
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +1
-0+ maxItems: 1
Best regards,
Krzysztof
Re: [PATCH v2 3/5] dt-bindings: leds: leds-is31fl32xx: Add shutdown-gpios property
Quoted 22 lines · Jun Yan
Quoted 21 lines
The IS31FL32XX series features an SDB shutdown pin.
Driving it low (active low) places the chip into hardware shutdown mode for power saving, while all register contents are preserved and registers are not reset.Add shutdown-gpios property to describe the GPIO connected to the SDB pin of IS31FL32XX series LED controllers.
Signed-off-by Jun Yan <[email protected]>--- .../devicetree/bindings/leds/issl,is31fl32xx.yaml | 12 ++++++++++++ 1 file changed, 12 insertions(+)Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +0
-0@@ -45,6 +45,15 @@ properties: When present, the chip's PWM will operate at ~22kHz as opposed to ~3kHz to move the operating frequency out of the audible range.
Quoted 3 lines
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml properties: · line 48
Quoted 1 line
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +1
-0+ shutdown-gpios:powerdown-gpios (see gpio-consumer-common)
Thanks for the reminder.This has already been implemented in v3. Sorry for the late reply.
Quoted 7 lines
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml properties: · line 49
Quoted 2 lines
Documentation/devicetree/bindings/leds/issl,is31fl32xx.yaml +1
-0+ maxItems: 1Best regards,
Krzysztof
PATCH v2 4/5 leds: is31fl32xx: Add shutdown pin to exit hardware shutdown mode
In reply to Jun YanThe IS31FL32XX series features an SDB shutdown pin.
Driving it low (active low) places the chip into hardware shutdown mode for power saving, while all register contents are preserved and registers are not reset.
Drive the pin logic low during probe() to exit hardware shutdown mode.
--- drivers/leds/leds-is31fl32xx.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/leds/leds-is31fl32xx.c +6 -0
@@ -60,6 +60,7 @@ struct is31fl32xx_led_data {struct is31fl32xx_priv {const struct is31fl32xx_chipdef *cdef;struct i2c_client *client; +struct gpio_desc *shutdown_gpio;unsigned int num_leds;struct is31fl32xx_led_data leds[]; };
@@ -421,6 +422,11 @@ static int is31fl32xx_parse_dt(struct device *dev,const struct is31fl32xx_chipdef *cdef = priv->cdef;int ret =0 ; + priv->shutdown_gpio =devm_gpiod_get_optional (dev,"shutdown" ,GPIOD_OUT_LOW ); +if (IS_ERR (priv->shutdown_gpio)) +return dev_err_probe (dev,PTR_ERR (priv->shutdown_gpio), +"Failed to get shutdown gpio\n" ); +if ((cdef->output_frequency_setting_reg !=IS31FL32XX_REG_NONE ) &&of_property_read_bool (dev_of_node (dev),"issi,22khz-pwm" )) {
Signature · 1 line
2.53.0
PATCH v2 5/5 leds: is31f132xx: Fix missing brightness_steps for is31f13236
In reply to Jun YanAdd missing brightness_steps for is31fl3236 to fix brightness control.
--- drivers/leds/leds-is31fl32xx.c | 1 + 1 file changed, 1 insertion(+)
drivers/leds/leds-is31fl32xx.c +1 -0
@@ -487,6 +487,7 @@ static const struct is31fl32xx_chipdef is31fl3236_cdef = { .pwm_register_base = 0x01, .led_control_register_base = 0x26, .enable_bits_per_led_control_register = 1, + .brightness_steps = 256, };static const struct is31fl32xx_chipdef is31fl3236a_cdef = {
Signature · 1 line
2.53.0