ASoC: cs35l56: Replace open-coded SoundWire regmap with generic regmap-sdw
Subsystems (3)
Richard Fitzgerald
maintainerv2 cover ASoC: cs35l56: Replace open-coded SoundWire regmap with generic regmap-sdw
This series replaces the entirely custom SoundWire regmap with the generic regmap-sdw. The reasons for doing this are:
- Avoid code duplication
- Avoid effort of keeping custom implementation up-to-date
- Prepare for supporting BRA
Changes in V2:
- Select REGMAP_SOUNDWIRE
Richard Fitzgerald (2):
ASoC: cs35l56: Use reg_base to offset addresses on SoundWire
ASoC: cs35l56: Use standard SoundWire regmap implementation
sound/soc/codecs/Kconfig | 2 +- sound/soc/codecs/cs35l56-sdw.c | 137 +++++++++++------------------- sound/soc/codecs/cs35l56-shared.c | 2 + sound/soc/codecs/cs35l56.h | 1 + 4 files changed, 53 insertions(+), 89 deletions(-)
Signature · 1 line
2.47.3
Richard Fitzgerald
maintainerPATCH v2 1/2 ASoC: cs35l56: Use reg_base to offset addresses on SoundWire
Set the reg_base member of regmap_config for SoundWire so that the regmap core will apply the 0x8000 offset to addresses, instead of doing it within our low-level regmap read/write callbacks.
---
No changes since V1.
sound/soc/codecs/cs35l56-sdw.c | 7 +------ sound/soc/codecs/cs35l56-shared.c | 2 ++ 2 files changed, 3 insertions(+), 6 deletions(-)
sound/soc/codecs/cs35l56-sdw.c +1 -6
@@ -59,8 +59,6 @@ static int cs35l56_sdw_slow_read(struct sdw_slave *peripheral, unsigned int reg, {int ret, i; - reg +=CS35L56_SDW_ADDR_OFFSET ; -for (i =0 ; i < val_size; i +=sizeof (u32)) {/* Poll for bus bridge idle */ ret = cs35l56_sdw_poll_mem_status(peripheral,
@@ -123,11 +121,9 @@ static int cs35l56_sdw_read(void *context, const void *reg_buf, reg =le32_to_cpu (*(const __le32 *)reg_buf); -if (cs35l56_is_otp_register (reg)) +if (cs35l56_is_otp_register (reg -CS35L56_SDW_ADDR_OFFSET ))return cs35l56_sdw_slow_read (peripheral, reg, buf8, val_size); - reg +=CS35L56_SDW_ADDR_OFFSET ; -if (val_size ==4 )return cs35l56_sdw_read_one (peripheral, reg, val_buf);
@@ -186,7 +182,6 @@ static int cs35l56_sdw_gather_write(void *context,int ret; reg =le32_to_cpu (*(const __le32 *)reg_buf); - reg +=CS35L56_SDW_ADDR_OFFSET ;if (val_size ==4 )return cs35l56_sdw_write_one (peripheral, reg, src_be);
sound/soc/codecs/cs35l56-shared.c +2 -0
@@ -1880,6 +1880,7 @@ EXPORT_SYMBOL_NS_GPL(cs35l56_regmap_spi, "SND_SOC_CS35L56_SHARED");const struct regmap_config cs35l56_regmap_sdw = { .reg_bits =32 , + .reg_base =0x8000 , .val_bits =32 , .reg_stride =4 , .reg_format_endian =REGMAP_ENDIAN_LITTLE ,
@@ -1915,6 +1916,7 @@ const struct regmap_config cs35l63_regmap_sdw = { .reg_bits = 32, .val_bits = 32, .reg_stride = 4, + .reg_base = 0x8000, .reg_format_endian = REGMAP_ENDIAN_LITTLE, .val_format_endian = REGMAP_ENDIAN_BIG, .max_register = CS35L56_DSP1_PMEM_5114,
Signature · 1 line
2.47.3
Richard Fitzgerald
maintainerRe: [PATCH v2 1/2] ASoC: cs35l56: Use reg_base to offset addresses on SoundWire
Quoted 6 lines · Richard Fitzgerald
Set the
reg_basemember ofregmap_configfor SoundWire so that the regmap core will apply the0x8000offset to addresses, instead of doing it within our low-level regmap read/write callbacks.Signed-off-by Richard Fitzgerald <[email protected]>---
STOP!
This also needs an update to the cs35l56 KUnit test for the changed addresses being passed to the dummy bus driver.
(This patch was written before the KUnit test existed)
Richard Fitzgerald
maintainerPATCH v2 2/2 ASoC: cs35l56: Use standard SoundWire regmap implementation
In reply to Richard FitzgeraldUse the regmap_sdw implementation for SoundWire instead of re-implementing the low-level bus transactions in cs35l56-sdw.c
The cs35l56 registers are big-endian on I2C and SPI but little-endian over SoundWire. The firmware files are all big-endian and contain opaque blobs in big-endian order. So these must be endian-swapped to transfer over SoundWire. A custom regmap bus implementation is used to do this endian-swapping.
The original implementation of this custom regmap bus was a complete bus backend, performing the endian swapping and low-level SoundWire bus read/write.
This commit changes the custom regmap bus to only perform the endian-swap. It uses an underlying simple uncached regmap_sdw bus to deal with transferring the 32-bit registers over the SoundWire bus. Although this adds a small amount of overhead, from passing through the regmap APIs twice, it avoids having a local duplicate implementation of what regmap_sdw already does.
The slow-read handling for OTP registers must access 8-bit SoundWire registers so it still uses low-level SoundWire bus reads.
---
Changed in V2:
- Select REGMAP_SOUNDWIRE
sound/soc/codecs/Kconfig | 2 +- sound/soc/codecs/cs35l56-sdw.c | 132 ++++++++++++--------------------- sound/soc/codecs/cs35l56.h | 1 + 3 files changed, 51 insertions(+), 84 deletions(-)
sound/soc/codecs/Kconfig +1 -1
@@ -887,7 +887,7 @@ config SND_SOC_CS35L56_SPI config SND_SOC_CS35L56_SDW tristate "Cirrus Logic CS35L56 CODEC (SDW)" depends on SOUNDWIRE - select REGMAP + select REGMAP_SOUNDWIRE select SND_SOC_CS35L56 select SND_SOC_CS35L56_SHARED help
sound/soc/codecs/cs35l56-sdw.c +49 -83
188 lines not on this page · raw message
sound/soc/codecs/cs35l56.h +1 -0
@@ -37,6 +37,7 @@ struct cs35l56_private {struct snd_soc_component *component;struct regulator_bulk_data supplies[CS35L56_NUM_BULK_SUPPLIES ];struct sdw_slave *sdw_peripheral; +struct regmap *sdw_bus_regmap;const char *fallback_fw_suffix;struct work_struct sdw_irq_work;bool sdw_irq_no_unmask;
Signature · 1 line
2.47.3