Add motorcomm 8531s set ds func and 8522 driver
Subsystems (4)
v6 cover Add motorcomm 8531s set ds func and 8522 driver
This patch is for Starfive JHB100 EVB board. JHB100 contain 1 RGMII/RMII and 1 RMII synopsys GMAC cores. In the EVB board, RGMII interface connect with YT8531s Ethernet PHY. RMII interface connect with YT8522 ethernet PHY. So patch 1-2 is for RGMII interface patch 3 is RMII is for RMII interface.
JHB100 is a Starfive new RISC-V SoC for datacenter BMC (BaseBoard Managent Controller). Similar with Aspeed 27x0.
The JHB100 minimal system upstream is in progress:
https://patchwork.kernel.org/project/linux-riscv/cover/[email protected]/
The patch base net-next (base commit list below)
previous commit
v1: https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v2:https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/ v3:
https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
v4:https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/
The change list:
v6:
1. patch3 correct AUTOSLEEP bit, (from sashiko test)
2. patch2 add review tag.
v5:
1. patch1 and patch3 add review tag
2. patch2 using phydev_id_compare()
v4:
1. Add review tag
2. patch 2 check interface first and Add the reason of checking PHY ID in commit message.
v3:
1. change some commit message.
v2:
1. patch1 move mdio lock out from yt8531_set_ds().
2. patch2 changed to phy_interface_is_rgmii().
Minda Chen (3):
net: phy: motorcomm: move mdio lock out from yt8531_set_ds()
net: motorcomm: phy: set drive strength in YT8531s RGMII
net: phy: motorcomm: Add YT8522 100M RMII PHY support
drivers/net/phy/motorcomm.c | 77 ++++++++++++++++++++++++++++++++----- 1 file changed, 67 insertions(+), 10 deletions(-)
base-commit: bfa3d89cc15c09f7d1581c834a5ed725189ec19f
Signature · 1 line
2.17.1
PATCH v6 1/3 net: phy: motorcomm: move mdio lock out from yt8531_set_ds()
yt8531_set_ds() default set register with mdio lock and only called with YT8531 PHY. But new type YT8531s support RGMII and has the same pin strength setting with YT8531, YT8531s need to call yt8531_set_ds() setting pin drive strength. But YT8531s config init function yt8521_config_init() already get the mdio lock with phy_select_page(). If calling yt8521_config_init() with mdio lock will cause dead lock.
Need to get the lock before calling yt8531_set_ds() and move mdio lock out from it for YT8531s.
--- drivers/net/phy/motorcomm.c | 23 ++++++++++++++--------- 1 file changed, 14 insertions(+), 9 deletions(-)
drivers/net/phy/motorcomm.c +14 -9
@@ -974,7 +974,8 @@ static u32 yt8531_get_ldo_vol(struct phy_device *phydev) {u32 val; - val =ytphy_read_ext_with_lock (phydev,YT8521_CHIP_CONFIG_REG ); + val =ytphy_read_ext (phydev,YT8521_CHIP_CONFIG_REG ); + val =FIELD_GET (YT8531_RGMII_LDO_VOL_MASK , val);return val <=YT8531_LDO_VOL_1V8 ? val :YT8531_LDO_VOL_1V8 ;
@@ -1010,10 +1011,11 @@ static int yt8531_set_ds(struct phy_device *phydev) ds =YT8531_RGMII_RX_DS_DEFAULT ; } - ret =ytphy_modify_ext_with_lock (phydev, -YTPHY_PAD_DRIVE_STRENGTH_REG , -YT8531_RGMII_RXC_DS_MASK , -FIELD_PREP (YT8531_RGMII_RXC_DS_MASK , ds)); + ret =ytphy_modify_ext (phydev, +YTPHY_PAD_DRIVE_STRENGTH_REG , +YT8531_RGMII_RXC_DS_MASK , +FIELD_PREP (YT8531_RGMII_RXC_DS_MASK , ds)); +if (ret <0 )return ret;
@@ -1033,10 +1035,11 @@ static int yt8531_set_ds(struct phy_device *phydev) ds_field_low =FIELD_GET (GENMASK (1 ,0 ), ds); ds_field_low =FIELD_PREP (YT8531_RGMII_RXD_DS_LOW_MASK , ds_field_low); - ret =ytphy_modify_ext_with_lock (phydev, -YTPHY_PAD_DRIVE_STRENGTH_REG , -YT8531_RGMII_RXD_DS_LOW_MASK |YT8531_RGMII_RXD_DS_HI_MASK , - ds_field_low | ds_field_hi); + ret =ytphy_modify_ext (phydev, +YTPHY_PAD_DRIVE_STRENGTH_REG , +YT8531_RGMII_RXD_DS_LOW_MASK |YT8531_RGMII_RXD_DS_HI_MASK , + ds_field_low | ds_field_hi); +if (ret <0 )return ret;
@@ -1825,7 +1828,9 @@ static int yt8531_config_init(struct phy_device *phydev)return ret; } +phy_lock_mdio_bus (phydev); ret =yt8531_set_ds (phydev); +phy_unlock_mdio_bus (phydev);if (ret <0 )return ret;
Signature · 1 line
2.17.1
PATCH v6 2/3 net: motorcomm: phy: set drive strength in YT8531s RGMII
In reply to Minda ChenSet RXD and RX CLK pin drive strength while in YT8531s connect with RGMII. Need to check 8531s PHY ID because 8521 and 8531s pin drive strength is different, 8521 can not call yt8531_set_ds().
--- drivers/net/phy/motorcomm.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/net/phy/motorcomm.c +5 -0
@@ -1697,6 +1697,11 @@ static int yt8521_config_init(struct phy_device *phydev)if (ret <0 ) goto err_restore_page; } + +if (phy_interface_is_rgmii (phydev) && +phydev_id_compare (phydev,PHY_ID_YT8531S )) + ret =yt8531_set_ds (phydev); + err_restore_page:return phy_restore_page (phydev, old_page, ret); }
Signature · 1 line
2.17.1
PATCH v6 3/3 net: phy: motorcomm: Add YT8522 100M RMII PHY support
In reply to Minda ChenAdd YT8522 100M RMII ethernet PHY base driver support, including PHY ID and base config init function.
--- drivers/net/phy/motorcomm.c | 49 ++++++++++++++++++++++++++++++++++++- 1 file changed, 48 insertions(+), 1 deletion(-)
drivers/net/phy/motorcomm.c +48 -1
@@ -1,6 +1,6 @@// SPDX-License-Identifier: GPL-2.0+ /* -* Motorcomm 8511/8521/8531/8531S/8821 PHY driver. +* Motorcomm 8511/8521/8522/8531/8531S/8821 PHY driver. * * Author: Peter Geis <[email protected]> * Author: Frank <[email protected]>
@@ -14,6 +14,7 @@#define PHY_ID_YT8511 0x0000010a#define PHY_ID_YT8521 0x0000011a +#define PHY_ID_YT8522 0x4f51e928#define PHY_ID_YT8531 0x4f51e91b#define PHY_ID_YT8531S 0x4f51e91a#define PHY_ID_YT8821 0x4f51ea19
@@ -227,6 +228,13 @@#define YT8521_LED_100_ON_EN BIT(5)#define YT8521_LED_10_ON_EN BIT(4) +#define YT8522_EXTREG_SLEEP_CONTROL 0x2027 +#define YT8522_EN_SLEEP_SW BIT(15) + +#define YT8522_EXTENDED_COMBO_CTRL 0x4000 +#define YT8522_RXDV_SEL BIT(4) +#define YT8522_RMII_EN BIT(1) +#define YTPHY_MISC_CONFIG_REG 0xA006#define YTPHY_MCR_FIBER_SPEED_MASK BIT(0)#define YTPHY_MCR_FIBER_1000BX (0x1 << 0)
@@ -1842,6 +1850,36 @@ static int yt8531_config_init(struct phy_device *phydev)return 0 ; } +static int yt8522_config_init (struct phy_device *phydev) +{ +struct device *dev = &phydev->mdio.dev; +int ret, val; + + val =ytphy_read_ext_with_lock (phydev,YT8522_EXTENDED_COMBO_CTRL ); +if (val <0 ) +return val; + +if (val &YT8522_RMII_EN ) { + val |=YT8522_RXDV_SEL ; + ret =ytphy_write_ext_with_lock (phydev, +YT8522_EXTENDED_COMBO_CTRL , + val); +if (ret <0 ) +return ret; + } + +if (device_property_read_bool (dev,"motorcomm,auto-sleep-disabled" )) { +/* disable auto sleep */ + ret =ytphy_modify_ext_with_lock (phydev, +YT8522_EXTREG_SLEEP_CONTROL , +YT8522_EN_SLEEP_SW ,0 ); +if (ret <0 ) +return ret; + } + +return 0 ; +} +/** * yt8531_link_change_notify() - Adjust the tx clock direction according to * the current speed and dts config.
@@ -3051,6 +3089,14 @@ static struct phy_driver motorcomm_phy_drvs[] = { .led_hw_control_set = yt8521_led_hw_control_set, .led_hw_control_get = yt8521_led_hw_control_get, }, + { + PHY_ID_MATCH_EXACT(PHY_ID_YT8522), + .name = "YT8522 100 Megabit Ethernet", + .config_aneg = genphy_config_aneg, + .config_init = yt8522_config_init, + .suspend = genphy_suspend, + .resume = genphy_resume, + }, {PHY_ID_MATCH_EXACT (PHY_ID_YT8531 ), .name = "YT8531 Gigabit Ethernet",
@@ -3111,6 +3157,7 @@ MODULE_LICENSE("GPL");static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = { {PHY_ID_MATCH_EXACT (PHY_ID_YT8511 ) }, {PHY_ID_MATCH_EXACT (PHY_ID_YT8521 ) }, + {PHY_ID_MATCH_EXACT (PHY_ID_YT8522 ) }, {PHY_ID_MATCH_EXACT (PHY_ID_YT8531 ) }, {PHY_ID_MATCH_EXACT (PHY_ID_YT8531S ) }, {PHY_ID_MATCH_EXACT (PHY_ID_YT8821 ) },
Signature · 1 line
2.17.1
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Hello:
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Quoted 10 lines · On Fri, 5 Jun 2026 14:02:09 +0800 you wrote:
This patch is for Starfive JHB100 EVB board. JHB100 contain 1 RGMII/RMII and 1 RMII synopsys GMAC cores. In the EVB board, RGMII interface connect with YT8531s Ethernet PHY. RMII interface connect with YT8522 ethernet PHY. So patch 1-2 is for RGMII interface patch 3 is RMII is for RMII interface.
JHB100 is a Starfive new RISC-V SoC for datacenter BMC (BaseBoard Managent Controller). Similar with Aspeed 27x0.
[...]
Here is the summary with links:
- [net-next,v6,1/3] net: phy: motorcomm: move mdio lock out from yt8531_set_ds()
https://git.kernel.org/netdev/net-next/c/0bfd6c8c959d - [net-next,v6,2/3] net: motorcomm: phy: set drive strength in YT8531s RGMII https://git.kernel.org/netdev/net-next/c/284975d609d0 - [net-next,v6,3/3] net: phy: motorcomm: Add YT8522 100M RMII PHY support https://git.kernel.org/netdev/net-next/c/554cfeb72e09
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html