arm64: dts: amlogic: add support for Orbbec Zora P1
Subsystems (2)
v2 cover arm64: dts: amlogic: add support for Orbbec Zora P1
The Orbbec Zora P1 is a vision development board based on the Amlogic A311D (Meson G12B) SoC, with 2 or 4 GiB LPDDR4, an Ampak AP6256 combo module (Broadcom BCM43456 Wi-Fi over SDIO and BCM4345C5 Bluetooth over UART_A), HDMI output and Gigabit Ethernet.
According to its specifications and original device tree, the board is a revised version of the ODROID-N2 with Wi-Fi, Bluetooth and an Amlogic A311D instead of the original S922X. The device tree therefore builds on meson-g12b-a311d.dtsi and meson-g12b-odroid-n2.dtsi, mirroring meson-g12b-odroid-n2-plus.dts. It extends those descriptions with the board-specific AP6256 wiring. The status LED is green instead of the original ODROID-N2 blue and has inverted polarity.
This series consists of:
Patch 1: add the "orbbec" vendor prefix.
Patch 2: document the "orbbec,zora-p1" board compatible. Patch 3: add the meson-g12b-zora-p1.dts board file and Makefile entry.
The DTB was built, validated against the amlogic.yaml binding using DT_SCHEMA_FILES, and boot-tested twice on the board. The AP6256 Wi-Fi interface enumerates and operates with the GPIOX_16 reset and PWM clock description present. Removing the wifi32k and pwm_ef descriptions causes the SDIO Wi-Fi device to stop working on this board.
---
Changes in v2:
- Investigated the apparent GPIOX_16 overlap between the SDIO power sequence reset and the 32.768 kHz PWM clock. Retained the description after two successful hardware tests; removing the clock description prevents the AP6256 Wi-Fi device from working.
- Sort the new DTB entry alphabetically in the Amlogic Makefile.
- Sort the "orbbec" entry alphabetically in vendor-prefixes.yaml.
Alberto Robazza (3):
dt-bindings: vendor-prefixes: add Orbbec
dt-bindings: arm: amlogic: document Orbbec Zora P1 board compatible
arm64: dts: amlogic: add support for Orbbec Zora P1
.../devicetree/bindings/arm/amlogic.yaml | 1 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-zora-p1.dts | 103 ++++++++++++++++++ 4 files changed, 107 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts
Signature · 1 line
2.55.0
PATCH v2 1/3 dt-bindings: vendor-prefixes: add Orbbec
Add the "orbbec" vendor prefix for Orbbec Inc., a manufacturer of 3D depth cameras and embedded vision boards. The prefix is needed by an upcoming board compatible string ("orbbec,zora-p1") introduced by this series.
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -1251,6 +1251,8 @@ patternProperties: description: Option NV "^oranth,.*": description: Shenzhen Oranth Technology Co., Ltd. + "^orbbec,.*": + description: Orbbec Inc. "^ORCL,.*": description: Oracle Corporation "^orisetech,.*":
Signature · 1 line
2.55.0
PATCH v2 2/3 dt-bindings: arm: amlogic: document Orbbec Zora P1 board compatible
In reply to Alberto RobazzaDocument the "orbbec,zora-p1" compatible for the Orbbec Zora P1 board, which is based on the Amlogic A311D (Meson G12B) SoC. The corresponding device tree is added in the follow-up patch.
The "orbbec" vendor prefix used here is added in the first patch of this series
--- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +1 -0
@@ -167,6 +167,7 @@ properties: - bananapi,bpi-m2s - khadas,vim3 - libretech,aml-a311d-cc + - orbbec,zora-p1 - radxa,zero2 - const: amlogic,a311d - const: amlogic,g12b
Signature · 1 line
2.55.0
PATCH v2 3/3 arm64: dts: amlogic: add support for Orbbec Zora P1
In reply to Alberto RobazzaThe Orbbec Zora P1 is an A311D (Meson G12B) board with 2/4 GiB DDR4, an Ampak AP6256 combo module (Broadcom BCM43456 Wi-Fi over SDIO and BCM4345C5 Bluetooth over UART_A), HDMI audio output.
According to the original Linux dts, the board is a modded version of the ODROID-N2, with Amlogic A311D instead of the original S922X and WiFi and Bluetooth support.
So the device tree builds on meson-g12b-a311d.dtsi and meson-g12b-odroid-n2.dtsi (using same vddcpu values of N2+), extended with the board-specific GPIO wiring for the AP6256 handling, and some modifications for the led, GPIO_ACTIVE_LOW instead of GPIO_ACTIVE_HIGH and different label (it is a green led, not blue as in the Odroid N2).
Add the "orbbec,zora-p1" compatible to the amlogic.yaml board binding (the "orbbec" vendor prefix is already registered) and the new DTB to the Makefile.
--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-zora-p1.dts | 103 ++++++++++++++++++ 2 files changed, 104 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
@@ -40,6 +40,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-bananapi-m2s.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-zora-p1.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +103 -0
103 lines not on this page · raw message
Signature · 1 line
2.55.0
[email protected]
AI reviewThank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [High] Pin multiplexing conflict on GPIOX_16 between the Wi-Fi SDIO power sequence reset and the…
Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [High] Pin multiplexing conflict on GPIOX_16 between the Wi-Fi SDIO power sequence reset and the 32.768kHz PWM clock. --
--- Patch [3]: [PATCH v2 3/3] arm64: dts: amlogic: add support for Orbbec Zora P1 --- commit 4c25c22b59ef54a3b08d02aab848d6f6aa6af1ef
Author: Alberto Robazza <[email protected]>
arm64: dts: amlogic: add support for Orbbec Zora P1
This commit adds device tree support for the Orbbec Zora P1 board, an A311D based device. It builds upon the ODROID-N2 device tree, adding specific GPIO wiring for Wi-Fi and Bluetooth over SDIO and UART_A. It also includes the board's compatible string and LED configurations.
Quoted 4 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +0
-0
[ ... ]
Quoted 13 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +13
-0+ sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; + };
[ ... ]
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts line 44
Quoted 3 lines
+&pwm_ef {
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +2
-0+ status = "okay"; + pinctrl-0 = <&pwm_e_pins>;
[Severity: High]
Will this create a pin multiplexing conflict on GPIOX_16?
The sdio_pwrseq node claims GPIOX_16 as a standard GPIO for the reset-gpios line. However, the pwm_ef node requests the pwm_e_pins pinctrl group. On the Amlogic G12B platform, pwm_e_pins maps exactly to GPIOX_16.
Since a single physical pin cannot concurrently output a 32kHz PWM clock signal and function as a static GPIO reset signal for the Wi-Fi module, will the pinctrl subsystem fail one of the requests and prevent the Wi-Fi module from initializing?
Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=3
[email protected]
maintainerQuoted 49 lines · Alberto Robazza
The Orbbec Zora P1 is an A311D (Meson G12B) board with 2/4 GiB DDR4, an Ampak AP6256 combo module (Broadcom BCM43456 Wi-Fi over SDIO and BCM4345C5 Bluetooth over
UART_A), HDMI audio output.According to the original Linux dts, the board is a modded version of the ODROID-N2, with Amlogic A311D instead of the original S922X and WiFi and Bluetooth support.
So the device tree builds onmeson-g12b-a311d.dtsiandmeson-g12b-odroid-n2.dtsi(using same vddcpu values of N2+), extended with the board-specific GPIO wiring for the AP6256 handling, and some modifications for the led,GPIO_ACTIVE_LOWinstead ofGPIO_ACTIVE_HIGHand different label (it is a green led, not blue as in the Odroid N2).Add the "orbbec,zora-p1" compatible to the
amlogic.yamlboard binding (the "orbbec" vendor prefix is already registered) and the new DTB to theMakefile.Signed-off-by Alberto Robazza <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-zora-p1.dts | 103 ++++++++++++++++++ 2 files changed, 104 insertions(+)create mode 100644
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -40,6 +40,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-bananapi-m2s.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-zora-p1.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtbarch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +6
-0@@ -0,0 +1,103 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2026 Alberto Robazza <[email protected]> + */ + +/dts-v1/;
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts line 16
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +10
-0+ +#include "meson-g12b-a311d.dtsi" +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "orbbec,zora-p1", "amlogic,a311d", "amlogic,g12b"; + model = "Orbbec Zora P1"; + + leds { + //The status led on Zora is actually green, same pin as N2, but reversed polarity
Use proper comment with /* and */
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts line 20
Quoted 4 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +4
-0+ led-blue { + label = "p1:green"; + gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_LOW>; + };
Please use the new bindings with function and color properties instead if label.
Quoted 60 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +60
-0+ }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_16 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; + }; + + sound { + model = "ZORA-P1"; + }; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; +}; + +/* AP6256 Wi-Fi: Broadcom BCM43456 over SDIO. */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + non-removable; + disable-wp; + keep-power-in-suspend; + + mmc-pwrseq = <&sdio_pwrseq>; + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&vddao_1v8>; + + wifi@1 { + compatible = "brcm,bcm4329-fmac"; + reg = <1>; + }; +}; + +/* AP6256 Bluetooth: Broadcom BCM4345C5 over UART_A. */ +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts line 90
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +10
-0+ bluetooth { + compatible = "brcm,bcm4345c5"; + shutdown-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_HIGH>; + max-speed = <2000000>; + clocks = <&wifi32k>; + clock-names = "lpo"; + }; +}; + +//vddcpu regulators same as Odroid N2+
Use proper comment with /* and */
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts line 103
Quoted 13 lines
arch/arm64/boot/dts/amlogic/meson-g12b-zora-p1.dts new file +13
-0+&vddcpu_a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; +}; + +&vddcpu_b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; +};
Thanks,
Neil