Skip to contentSkip to conversation

riscv: csr: do not drop C bit on misa write

PATCH Superseded Vladimir Isaev 3 participants 5 messages Aug 6 – Aug 13 RISC-V

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 riscv: csr: do not drop C bit on misa write

According to spec:

Quoted 4 lines

Writing misa may increase IALIGN, e.g., by disabling the "C" extension. If an instruction that would write misa increases IALIGN, and the subsequent instruction’s address is not IALIGN-bit aligned, the write to misa is suppressed, leaving misa unchanged.

So attempt to disable C extension if next instruction is not aligned should not change the misa.

---
 target/riscv/tcg/csr.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
target/riscv/tcg/csr.c +4 -3
index 36f2004bc5..58c206c1fa 100644
@@ -2182,9 +2182,10 @@ static RISCVException write_misa(CPURISCVState *env, int csrno,
     /* Mask extensions that are not supported by this hart */
     val &= env->misa_ext_mask;
 
-    /* Suppress 'C' if next instruction is not aligned. */
-    if ((val & RVC) && (get_next_pc(env, ra) & 3) != 0) {
-        val &= ~RVC;
+    /* drop write if RVC is cleared and next instruction is not aligned */
+    if ((env->misa_ext & RVC) && !(val & RVC) &&
+         (get_next_pc(env, ra) & 3) != 0) {
+        return RISCV_EXCP_NONE;
     }
 
     /* Disable RVG if any of its dependencies are disabled */
Signature · 1 line
2.55.0
#1 lore raw

PATCH 2/2 tests/tcg/riscv64: add misa write test

Add test to check that writing misa before compact instruction doesn't drop any bits.

---
 tests/tcg/riscv64/Makefile.softmmu-target |  4 ++
 tests/tcg/riscv64/test-misa-w.S           | 46 +++++++++++++++++++++++
 2 files changed, 50 insertions(+)
 create mode 100644 tests/tcg/riscv64/test-misa-w.S
tests/tcg/riscv64/Makefile.softmmu-target +4 -0
index 82be8a2c91..e7d052909f 100644
@@ -41,5 +41,9 @@ comma:= ,
 run-test-crc32: test-crc32
 	$(call run-test, $<, $(QEMU) -cpu rv64$(comma)xlrbr=true $(QEMU_OPTS)$<)
 
+EXTRA_RUNS += run-test-misa-w
+run-test-misa-w: test-misa-w
+	$(call run-test, $<, $(QEMU) -cpu rv64$(comma)x-misa-w=true$(comma)c=true $(QEMU_OPTS)$<)
+
 # We don't currently support the multiarch system tests
 undefine MULTIARCH_TESTS
tests/tcg/riscv64/test-misa-w.S new file +46 -0

46 lines not on this page · raw message

Signature · 1 line
2.55.0
Reviewed-by Alistair Francis on v1 2/2
#2 lore raw

Re: [PATCH 2/2] tests/tcg/riscv64: add misa write test

Quoted 5 lines · Vladimir Isaev

Add test to check that writing misa before compact instruction doesn't
drop any bits.

Alistair

Quoted 77 lines

---
 tests/tcg/riscv64/Makefile.softmmu-target |  4 ++ tests/tcg/riscv64/test-misa-w.S           | 46
+++++++++++++++++++++++

 2 files changed, 50 insertions(+)

 create mode 100644 tests/tcg/riscv64/test-misa-w.S

tests/tcg/riscv64/Makefile.softmmu-target +0 -0
index 82be8a2c91..e7d052909f 100644
@@ -41,5 +41,9 @@ comma:= ,

 run-test-crc32: test-crc32
  $(call run-test, $<, $(QEMU) -cpu rv64$(comma)xlrbr=true $(QEMU_OPTS)$<)

tests/tcg/riscv64/Makefile.softmmu-target +3 -0
+EXTRA_RUNS += run-test-misa-w
+run-test-misa-w: test-misa-w
+	$(call run-test, $<, $(QEMU) -cpu rv64$(comma)x-misa-

w=true$(comma)c=true $(QEMU_OPTS)$<)
+
 # We don't currently support the multiarch system tests undefine MULTIARCH_TESTS

tests/tcg/riscv64/test-misa-w.S new file +46 -0
new file mode 100644
index 0000000000..22cba98b8c
@@ -0,0 +1,46 @@
+#define MISA_C (1<<2)
+
+	.text
+	.globl _start
+	.balign 4
+_start:
+	.option norvc
+	lla t0, trap
+	csrw mtvec, t0
+
+	# Fail if misa after write is not the same as before
+	csrr t0, misa
+	.option rvc
+	c.nop
+	csrw misa, t0
+	c.nop
+	csrr t1, misa
+	bne t0, t1, fail
+
+	li a0, 0
+	j  _exit
+
+
+	.balign 4
+	.option norvc
+trap:
+fail:
+	li	a0, 1
+_exit:
+	lla	a1, semiargs
+	li	t0, 0x20026	# ADP_Stopped_ApplicationExit
+	sd	t0, 0(a1)
+	sd	a0, 8(a1)
+	li	a0, 0x20	# TARGET_SYS_EXIT_EXTENDED
+
+	# Semihosting call sequence
+	.balign	16
+	slli	zero, zero, 0x1f
+	ebreak
+	srai	zero, zero, 0x7
+	j	.
+
+	.data
+	.balign	16
+semiargs:
+	.space	16
Reviewed-by Alistair Francis on v1 1/2
#3 lore raw
In reply to Vladimir Isaev
Quoted 7 lines · Vladimir Isaev

According to spec:

Quoted 5 lines

Writing misa may increase IALIGN, e.g., by disabling the "C" extension.
If an instruction that would write misa increases IALIGN, and the subsequent instruction’s address is not IALIGN-bit aligned, the write to misa is suppressed, leaving misa unchanged.

Quoted 5 lines

So attempt to disable C extension if next instruction is not aligned should not
change the misa.

Thanks for the patches.

Can you please re-send the series with a cover-letter. All multi-patch series should have a cover letter

Alistair

Quoted 24 lines

---
 target/riscv/tcg/csr.c | 7 ++++---

 1 file changed, 4 insertions(+), 3 deletions(-)
target/riscv/tcg/csr.c +0 -0
index 36f2004bc5..58c206c1fa 100644
@@ -2182,9 +2182,10 @@ static RISCVException write_misa(CPURISCVState
 *env, int csrno,
      /* Mask extensions that are not supported by this hart */
      val &= env->misa_ext_mask;


-    /* Suppress 'C' if next instruction is not aligned. */ -    if ((val & RVC) && (get_next_pc(env, ra) & 3) != 0) { -        val &= ~RVC;
+    /* drop write if RVC is cleared and next instruction is not aligned */
+    if ((env->misa_ext & RVC) && !(val & RVC) &&
+         (get_next_pc(env, ra) & 3) != 0) {
+        return RISCV_EXCP_NONE;
     }

     /* Disable RVG if any of its dependencies are disabled */

#4 lore raw
In reply to Vladimir Isaev
Quoted 21 lines · Vladimir Isaev

According to spec:

Quoted 4 lines

Writing misa may increase IALIGN, e.g., by disabling the "C" extension. If an instruction that would write misa increases IALIGN, and the subsequent instruction’s address is not IALIGN-bit aligned, the write to misa is suppressed, leaving misa unchanged.

So attempt to disable C extension if next instruction is not aligned should not change the misa.

---
 target/riscv/tcg/csr.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)
target/riscv/tcg/csr.c +0 -0
index 36f2004bc5..58c206c1fa 100644
@@ -2182,9 +2182,10 @@ static RISCVException write_misa(CPURISCVState *env, int csrno,
     /* Mask extensions that are not supported by this hart */

target/riscv/tcg/csr.c static RISCVException write_misa(CPURISCVState *env, int csrno, · line 2189

Quoted 10 lines
target/riscv/tcg/csr.c +4 -3
     val &= env->misa_ext_mask;
 
-    /* Suppress 'C' if next instruction is not aligned. */
-    if ((val & RVC) && (get_next_pc(env, ra) & 3) != 0) {
-        val &= ~RVC;
+    /* drop write if RVC is cleared and next instruction is not aligned */
+    if ((env->misa_ext & RVC) && !(val & RVC) &&
+         (get_next_pc(env, ra) & 3) != 0) {
+        return RISCV_EXCP_NONE;
     }

I thought we'd already fixed this so I went hunting. This is similar to Nick's patch:

https://lore.kernel.org/qemu-devel/acTSDKzeEb3bbv08@lima-default/

I think the conclusion there was to additionally check ra, and do a qemu_log_mask(LOG_GUEST_ERROR, ...)

I don't think he got around to sending the next version of that series.

Cheers,

Joel