Skip to contentSkip to conversation

dmaengine: ste_dma40: Fix numerous accumulated bugs

PATCH Applied Linus Walleij 4 participants 37 messages Sep 27 – Oct 5

Subsystems (2)

v7 of 8 Applied Latest is v8 →

lore
Share & tools
lore

Linus Walleij

author maintainer
#0 lore raw

v7 cover dmaengine: ste_dma40: Fix numerous accumulated bugs

This series fixes many DMA40 bugs.

Roughly half were found while reviewing the Ux500 LCLA SRAM power-domain conversion.

The cyclic transfer residue bug was exposed by Ux500 audio playback.

The rest were identified during review and hardware-manual audit.

The method taken is: whenever Sashiko complains: fix the bug it complains about if possible.

This has been boot tested on the Samsung Skomer device: DMA for MMC, wireless SDIO and UART still works after these patches, and DMA for audio started working.

Assisted-by LLM

---
Changes in v7:
- This is getting tedious, should I move the reviewed and non-complained patches to the front of the series so Vinod can start applying
them?
- Use modulo arithmetic for cyclic callback pointer displacement.
- Request the IRQ after DMA40 initialization clears pending status.
- Replace probe IRQ bookkeeping with explicit cleanup labels.
- Use non-resetting devres actions for unpublished channel tasklets.
- Derive V4B physical-channel allocation and GCC clock groups from its five-event-group layout.
- Link to v6: https://lore.kernel.org/r/[email protected]

Changes in v6:
- Simplify termination and channel-release runtime PM balancing by releasing temporary references in the successful resume paths. Descriptor cleanup remains unconditional because it does not access DMA40 registers.
- Name and document the three-attempt cyclic-residue pointer sampling bound, and remove an unrelated whitespace-only change from that patch.
- Replace probe-local runtime PM bookkeeping with devm_pm_runtime_set_active_enabled(), keeping IRQ registration after runtime PM is enabled.
- Link to v5: https://lore.kernel.org/r/[email protected]

Changes in v5:
- Respin to fix some further corner cases found by Sashiko as well
as can be done.
- Resynchronize cyclic callback tracking after failed hardware-pointer samples and limit unchanged-pointer interrupts to one callback. DMA40 has only one latched terminal-count bit, so extra periods coalesced while the pointer is unavailable and exact one-or-more full-buffer laps cannot be recovered without risking spurious callbacks.
- Count DMA40 status from channels owned by other SoC cores as handled without acknowledging it, so only status-less interrupts return IRQ_NONE and foreign DMA traffic cannot trigger spurious-IRQ disabling.
This is REALLY FRINGE but let's do our best anyway!
- Link to v4: https://lore.kernel.org/r/[email protected]

Changes in v4:
- Rework cyclic-transfer residue reporting to use the current memory-side hardware pointer and reject periods that need more than one LLI.
- Add cyclic callback recovery when terminal-count interrupts coalesce.
- Retire all issued descriptors and release software channel state when a runtime PM resume fails, while avoiding inaccessible hardware registers.
- Validate physical event IDs against the variant event-group limit rather than the physical channel count, as confirmed by the DB8500 manual.
- Link to v3: https://lore.kernel.org/r/[email protected]

Changes in v3:
- Add a fix so physical channels advertise their existing cyclic support.
- Add a cyclic-transfer residue fix so DMAengine PCM reports the correct hardware pointer and Ux500 audio playback does not stop with -EIO.
- In patch 3, preserve cookie completion order when the next queued transfer fails to start and retire failed cyclic descriptors.
- In patch 4, enable runtime PM before requesting the IRQ so pending interrupts can be acknowledged during probe.
- In patch 5, keep valid interrupt handling with CONFIG_PM disabled and only drop a runtime PM reference when one was acquired.
- Add checked runtime PM resume handling to channel operations.
- Add an IRQ status patch returning IRQ_NONE when no DMA40 interrupt was acknowledged.
- In patch 8, keep the IRQ disabled until hardware initialization has configured and cleared the DMA40 interrupt state.
- In the DMA registration unwind patch, free the IRQ before unregistering the DMA devices and drain initialized tasklets before releasing storage.
- Add a fix releasing the LCPA SRAM node reference after reading it.
- Move the disabled-channels binding restoration to its own series.
- Store memcpy channel mappings per controller and check the property read.
- Add validation for disabled physical channel indexes.
- Reject DMA specifiers that do not contain exactly three cells.
- Reject transfer direction changes after channel allocation so logical channel resource masks are released correctly.
- In the event-group bounds patch, use variant-specific limits so DB8540 event group 4 remains available.
- Add fixed-channel fixes that search later physical blocks and validate configured physical channel indexes.
- Move the generic DMAengine debugfs naming fix to its own series.
- Use Assisted-by: LLM for the existing assistance trailers.
- Rebase onto v7.3-rc1.
- Link to v2: https://lore.kernel.org/r/[email protected]

Changes in v2:
- In patch 1, complete the failed-start descriptor through the normal tasklet path and drop the runtime PM reference instead of freeing the submitted descriptor directly.
- Add an IRQ fix to avoid register access when DMA40 is runtime suspended.
- Add a probe ordering fix so DMA40 hardware is initialized before DMAengine devices are registered.
- Add a probe unwind fix so DMAengine registrations are released before freeing IRQ and LCLA resources.
- Add an LCLA allocation fix so __get_free_pages() and free_pages() use an allocation order instead of a raw page count.
- Add a probe unwind fix so ESRAM LCLA mappings are not released with free_pages().
- Add a device tree parsing fix so memcpy-channels cannot overflow the memcpy channel array.
- Add a dev_type bounds fix so derived event groups cannot overflow
phy_res or the priority/realtime register window.
- Add validation for fallback memcpy configurations so memcpy-channels entries cannot bypass the dev_type bounds checks.
- Add a DMAengine debugfs naming fix so drivers registering several DMAengine devices for one parent device do not trigger duplicate-name warnings.
- Link to v1: https://lore.kernel.org/r/[email protected]

---
Linus Walleij (24):
dmaengine: ste_dma40: Fix physical cyclic capability
dmaengine: ste_dma40: Fix cyclic transfer residue
dmaengine: ste_dma40: Recover coalesced cyclic callbacks
dmaengine: ste_dma40: Fix failed start cleanup
dmaengine: ste_dma40: Fix probe runtime PM disable
dmaengine: ste_dma40: Check runtime PM in IRQ
dmaengine: ste_dma40: Handle runtime PM resume errors
dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending
dmaengine: ste_dma40: Init hardware before registration
dmaengine: ste_dma40: Fix probe IRQ leak
dmaengine: ste_dma40: Fix DMA registration unwind
dmaengine: ste_dma40: Fix LCLA allocation order
dmaengine: ste_dma40: Fix probe LCLA free
dmaengine: ste_dma40: Put the LCPA SRAM node
dmaengine: ste_dma40: Fix memcpy channel parsing
dmaengine: ste_dma40: Validate disabled channel indexes
dmaengine: ste_dma40: Validate DMA specifier length
dmaengine: ste_dma40: Reject direction changes after allocation
dmaengine: ste_dma40: Fix logical channel bounds check
dmaengine: ste_dma40: Fix event group bounds
dmaengine: ste_dma40: Fix V4B event group mapping
dmaengine: ste_dma40: Search all blocks for fixed logical channels
dmaengine: ste_dma40: Validate fixed physical channel indexes
dmaengine: ste_dma40: Validate memcpy configuration

 drivers/dma/ste_dma40.c    | 590 ++++++++++++++++++++++++++++++++++-----------
 drivers/dma/ste_dma40_ll.h |   2 -
 2 files changed, 455 insertions(+), 137 deletions(-)

---
base-commit: cee9395acd8043be0644b25c34bfa86623f2b935
change-id: 20260820-dma40-fixes-b99af66002bf

Best regards,

Signature · 1 line
Linus Walleij <[email protected]>
author maintainer
#1 lore raw

PATCH v7 1/24 dmaengine: ste_dma40: Fix physical cyclic capability

d40_dmaengine_init() configures dma_both for physical channels that can handle both slave and memcpy transfers. Physical DMA40 channel setup has supported cyclic LLIs since cyclic transfer support was added, but the DMA_CYCLIC capability is set on dma_slave a second time instead of dma_both.

Set DMA_CYCLIC on dma_both so d40_ops_init() installs device_prep_dma_cyclic and physical channels advertise cyclic support.

Fixes 0c842b551063 ("dma40: cyclic xfer support")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/dma/ste_dma40.c +1 -1
index 0d9ffa3e2663..e4d689c9eba8 100644
@@ -2897,7 +2897,7 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 	dma_cap_zero(base->dma_both.cap_mask);
 	dma_cap_set(DMA_SLAVE, base->dma_both.cap_mask);
 	dma_cap_set(DMA_MEMCPY, base->dma_both.cap_mask);
-	dma_cap_set(DMA_CYCLIC, base->dma_slave.cap_mask);
+	dma_cap_set(DMA_CYCLIC, base->dma_both.cap_mask);
 
 	d40_ops_init(base, &base->dma_both);
 	err = dmaenginem_async_device_register(&base->dma_both);
Signature · 1 line
2.55.0
author maintainer
#2 lore raw

PATCH v7 2/24 dmaengine: ste_dma40: Fix cyclic transfer residue

In reply to Linus Walleij

DMA40 reads residue from the element count of the currently active LLI. For a cyclic transfer this reports at most one period, not the bytes remaining until the cyclic buffer wraps.

Once DMA40 advertises burst granularity, DMAengine PCM uses this residue directly. For a four-period PCM buffer it consequently reports the hardware pointer near three periods after every period interrupt. ALSA eventually stops playback with -EIO although DMA period callbacks continue.

Calculate cyclic residue from the current memory-side hardware pointer instead. Read the destination pointer for capture and the source pointer for playback. Sample the split logical channel pointer coherently and retain the last valid residue during relink transitions.

Make at most three residue sampling attempts: one initial read plus two retries. The retries let transient split-register updates or LLI relink windows settle, while the limit prevents unbounded polling if hardware does not yield a valid pointer.

This avoids counting terminal-count interrupts, which races with hardware advancing to the next LLI and cannot account for coalesced interrupt status. Also reject cyclic periods that expand into multiple LLIs because logical cyclic LLIs each request a terminal-count interrupt and would generate more than one callback per period.

Reject invalid cyclic geometries before dividing or constructing the scatterlist as well.

Fixes 15c606686541 ("dmaengine: ste_dma40: indicate granularity on channels")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 106 +++++++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 101 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +101 -5
index e4d689c9eba8..eab9c09b4bfe 100644
@@ -65,6 +65,9 @@ struct stedma40_platform_data {
 /* Maximum iterations taken before giving up suspending a channel */
 #define D40_SUSPEND_MAX_IT 500
 
+/* Maximum attempts to sample a stable cyclic residue position */
+#define D40_RESIDUE_MAX_ATTEMPTS 3
+
 /* Milliseconds */
 #define DMA40_AUTOSUSPEND_DELAY	100
 
@@ -378,6 +381,9 @@ struct d40_lli_pool {
  * @lli_len: Number of llis of current descriptor.
  * @lli_current: Number of transferred llis.
  * @lcla_alloc: Number of LCLA entries allocated.
+ * @cyclic_dma_addr: Start address of the cyclic buffer.
+ * @cyclic_buf_len: Length of the cyclic buffer.
+ * @cyclic_residue: Last valid cyclic residue sample.
  * @txd: DMA engine struct. Used for among other things for communication
  * during a transfer.
  * @node: List entry.
@@ -396,6 +402,9 @@ struct d40_desc {
 	int				 lli_len;
 	int				 lli_current;
 	int				 lcla_alloc;
+	dma_addr_t			 cyclic_dma_addr;
+	size_t				 cyclic_buf_len;
+	size_t				 cyclic_residue;
 
 	struct dma_async_tx_descriptor	 txd;
 	struct list_head		 node;
@@ -1420,6 +1429,64 @@ static u32 d40_residue(struct d40_chan *d40c)
 	return num_elt * d40c->dma_cfg.dst_info.data_width;
 }
 
+static bool d40_current_addr(struct d40_chan *d40c, dma_addr_t *addr)
+{
+	bool dst = d40c->dma_cfg.dir == DMA_DEV_TO_MEM;
+	void __iomem *high_reg;
+	void __iomem *low_reg;
+	u32 low;
+	u32 high;
+	u32 check;
+	int i;
+
+	if (chan_is_physical(d40c)) {
+		*addr = readl(chan_base(d40c) +
+			      (dst ? D40_CHAN_REG_SDPTR : D40_CHAN_REG_SSPTR));
+		return true;
+	}
+
+	if (dst) {
+		low_reg = &d40c->lcpa->lcsp2;
+		high_reg = &d40c->lcpa->lcsp3;
+	} else {
+		low_reg = &d40c->lcpa->lcsp0;
+		high_reg = &d40c->lcpa->lcsp1;
+	}
+
+	for (i = 0; i < D40_RESIDUE_MAX_ATTEMPTS; i++) {
+		high = readl(high_reg) & D40_MEM_LCSP1_SPTR_MASK;
+		low = readl(low_reg) & D40_MEM_LCSP0_SPTR_MASK;
+		check = readl(high_reg) & D40_MEM_LCSP1_SPTR_MASK;
+		if (high == check) {
+			*addr = low | high;
+			return true;
+		}
+	}
+
+	return false;
+}
+
+static bool d40_cyclic_offset(struct d40_chan *d40c, struct d40_desc *d40d,
+			      size_t *offset)
+{
+	dma_addr_t current_addr;
+	dma_addr_t current_offset;
+	int i;
+
+	for (i = 0; i < D40_RESIDUE_MAX_ATTEMPTS; i++) {
+		if (!d40_current_addr(d40c, &current_addr))
+			continue;
+
+		current_offset = current_addr - d40d->cyclic_dma_addr;
+		if (current_offset <= d40d->cyclic_buf_len) {
+			*offset = current_offset;
+			return true;
+		}
+	}
+
+	return false;
+}
+
 static bool d40_tx_is_linked(struct d40_chan *d40c)
 {
 	bool is_link;
@@ -2108,15 +2175,26 @@ static bool d40_is_paused(struct d40_chan *d40c)
 
 }
 
-static u32 stedma40_residue(struct dma_chan *chan)
+static u32 stedma40_residue(struct dma_chan *chan, dma_cookie_t cookie)
 {
 	struct d40_chan *d40c =
 		container_of(chan, struct d40_chan, chan);
+	struct d40_desc *d40d;
+	size_t offset;
 	u32 bytes_left;
 	unsigned long flags;
 
 	spin_lock_irqsave(&d40c->lock, flags);
-	bytes_left = d40_residue(d40c);
+	d40d = d40_first_active_get(d40c);
+	if (d40d && d40d->txd.cookie == cookie && d40d->cyclic &&
+	    d40d->cyclic_buf_len) {
+		if (d40_cyclic_offset(d40c, d40d, &offset))
+			d40d->cyclic_residue = d40d->cyclic_buf_len - offset;
+		bytes_left = d40d->cyclic_residue;
+	} else {
+		bytes_left = d40_residue(d40c);
+	}
+
 	spin_unlock_irqrestore(&d40c->lock, flags);
 
 	return bytes_left;
@@ -2246,8 +2324,13 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 	if (desc == NULL)
 		goto unlock;
 
-	if (sg_next(&sg_src[sg_len - 1]) == sg_src)
+	if (sg_next(&sg_src[sg_len - 1]) == sg_src) {
 		desc->cyclic = true;
+		if (desc->lli_len != sg_len) {
+			chan_err(chan, "Cyclic periods must fit in one LLI\n");
+			goto free_desc;
+		}
+	}
 
 	src_dev_addr = 0;
 	dst_dev_addr = 0;
@@ -2524,11 +2607,18 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr,
 		     size_t buf_len, size_t period_len,
 		     enum dma_transfer_direction direction, unsigned long flags)
 {
-	unsigned int periods = buf_len / period_len;
+	unsigned int periods;
 	struct dma_async_tx_descriptor *txd;
+	struct d40_desc *desc;
 	struct scatterlist *sg;
+	dma_addr_t buf_addr = dma_addr;
 	int i;
 
+	if (!buf_len || !period_len || buf_len % period_len)
+		return NULL;
+
+	periods = buf_len / period_len;
+
 	sg = kzalloc_objs(struct scatterlist, periods + 1, GFP_NOWAIT);
 	if (!sg)
 		return NULL;
@@ -2543,6 +2633,12 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr,
 
 	txd = d40_prep_sg(chan, sg, sg, periods, direction,
 			  DMA_PREP_INTERRUPT);
+	if (txd) {
+		desc = container_of(txd, struct d40_desc, txd);
+		desc->cyclic_dma_addr = buf_addr;
+		desc->cyclic_buf_len = buf_len;
+		desc->cyclic_residue = buf_len;
+	}
 
 	kfree(sg);
 
@@ -2563,7 +2659,7 @@ static enum dma_status d40_tx_status(struct dma_chan *chan,
 
 	ret = dma_cookie_status(chan, cookie, txstate);
 	if (ret != DMA_COMPLETE && txstate)
-		dma_set_residue(txstate, stedma40_residue(chan));
+		dma_set_residue(txstate, stedma40_residue(chan, cookie));
 
 	if (d40_is_paused(d40c))
 		ret = DMA_PAUSED;
Signature · 1 line
2.55.0
author maintainer
#3 lore raw

PATCH v7 3/24 dmaengine: ste_dma40: Recover coalesced cyclic callbacks

In reply to Linus Walleij

DMA40 has one terminal-count status bit per channel, so cyclic period interrupts can coalesce.

Use the memory-side pointer displacement to queue the minimum observable number of callbacks. If sampling fails, queue one callback and invalidate the saved position; the next successful sample resynchronizes without recounting it.

The pointer is modulo the cyclic buffer: a displacement of d periods can mean d plus n complete iterations of the buffer. Report d, so the driver could have missed n iterations of the buffer; DMA40 has no counter to recover them. For an unchanged pointer, report one callback rather than risk a spurious full-buffer burst.

This condition has not been seen in practice and is only a product of review comments that the buffer can miss interrupts.

The preceding cyclic-residue fix ensures that every cyclic period fits in one LLI, so each boundary corresponds to one client callback.

Fixes 0c842b551063 ("dma40: cyclic xfer support")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 69 ++++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 68 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +68 -1
index eab9c09b4bfe..4b138aa313c8 100644
@@ -384,11 +384,14 @@ struct d40_lli_pool {
  * @cyclic_dma_addr: Start address of the cyclic buffer.
  * @cyclic_buf_len: Length of the cyclic buffer.
  * @cyclic_residue: Last valid cyclic residue sample.
+ * @cyclic_period_len: Length of one cyclic period.
+ * @cyclic_callback_pos: Position after the callbacks already queued.
  * @txd: DMA engine struct. Used for among other things for communication
  * during a transfer.
  * @node: List entry.
  * @is_in_client_list: true if the client owns this descriptor.
  * @cyclic: true if this is a cyclic job
+ * @cyclic_callback_pos_valid: Whether cyclic_callback_pos is reliable.
  *
  * This descriptor is used for both logical and physical transfers.
  */
@@ -405,12 +408,15 @@ struct d40_desc {
 	dma_addr_t			 cyclic_dma_addr;
 	size_t				 cyclic_buf_len;
 	size_t				 cyclic_residue;
+	size_t				 cyclic_period_len;
+	size_t				 cyclic_callback_pos;
 
 	struct dma_async_tx_descriptor	 txd;
 	struct list_head		 node;
 
 	bool				 is_in_client_list;
 	bool				 cyclic;
+	bool				 cyclic_callback_pos_valid;
 };
 
 /**
@@ -1487,6 +1493,61 @@ static bool d40_cyclic_offset(struct d40_chan *d40c, struct d40_desc *d40d,
 	return false;
 }
 
+static unsigned int d40_cyclic_periods_elapsed(struct d40_chan *d40c,
+					       struct d40_desc *d40d)
+{
+	size_t current_pos;
+	size_t delta;
+	size_t offset;
+	unsigned int periods;
+
+	if (!d40d->cyclic_period_len)
+		return 1;
+
+	if (!d40_cyclic_offset(d40c, d40d, &offset)) {
+		d40d->cyclic_callback_pos_valid = false;
+		return 1;
+	}
+
+	current_pos = rounddown(offset, d40d->cyclic_period_len);
+	if (!d40_residue(d40c) && current_pos != offset)
+		current_pos += d40d->cyclic_period_len;
+	if (current_pos == d40d->cyclic_buf_len)
+		current_pos = 0;
+
+	if (!d40d->cyclic_callback_pos_valid) {
+		/*
+		 * The previous interrupt was reported without a pointer
+		 * sample. Resynchronize without using the stale position,
+		 * which would count that callback again.
+		 */
+		d40d->cyclic_callback_pos = current_pos;
+		d40d->cyclic_callback_pos_valid = true;
+		return 1;
+	}
+
+	/*
+	 * The pointer wraps with the cyclic buffer, so its displacement is
+	 * only the minimum number of elapsed periods. Complete buffer laps
+	 * are not observable.
+	 */
+	delta = (current_pos + d40d->cyclic_buf_len -
+		 d40d->cyclic_callback_pos) % d40d->cyclic_buf_len;
+	periods = delta / d40d->cyclic_period_len;
+	if (!periods) {
+		/*
+		 * The TC status is a single latched bit. An unchanged pointer
+		 * cannot distinguish a complete lap from a repeated interrupt,
+		 * so do not amplify it into a buffer's worth of callbacks.
+		 */
+		periods = 1;
+	}
+
+	d40d->cyclic_callback_pos = current_pos;
+
+	return periods;
+}
+
 static bool d40_tx_is_linked(struct d40_chan *d40c)
 {
 	bool is_link;
@@ -1609,6 +1670,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
 static void dma_tc_handle(struct d40_chan *d40c)
 {
 	struct d40_desc *d40d;
+	unsigned int callbacks = 1;
 
 	/* Get first active entry from list */
 	d40d = d40_first_active_get(d40c);
@@ -1633,6 +1695,8 @@ static void dma_tc_handle(struct d40_chan *d40c)
 			if (d40d->lli_current == d40d->lli_len)
 				d40d->lli_current = 0;
 		}
+
+		callbacks = d40_cyclic_periods_elapsed(d40c, d40d);
 	} else {
 		d40_lcla_free_all(d40c, d40d);
 
@@ -1653,7 +1717,7 @@ static void dma_tc_handle(struct d40_chan *d40c)
 		d40_desc_done(d40c, d40d);
 	}
 
-	d40c->pending_tx++;
+	d40c->pending_tx += callbacks;
 	tasklet_schedule(&d40c->tasklet);
 
 }
@@ -2638,6 +2702,9 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr,
 		desc->cyclic_dma_addr = buf_addr;
 		desc->cyclic_buf_len = buf_len;
 		desc->cyclic_residue = buf_len;
+		desc->cyclic_period_len = period_len;
+		desc->cyclic_callback_pos = 0;
+		desc->cyclic_callback_pos_valid = true;
 	}
 
 	kfree(sg);
Signature · 1 line
2.55.0
Reviewed-by on v7 3/24
#4 lore raw

Re: [PATCH v7 03/24] dmaengine: ste_dma40: Recover coalesced cyclic callbacks

Quoted 17 lines · Linus Walleij

DMA40 has one terminal-count status bit per channel, so cyclic period interrupts can coalesce.

Use the memory-side pointer displacement to queue the minimum observable number of callbacks. If sampling fails, queue one callback and invalidate the saved position; the next successful sample resynchronizes without recounting it.

The pointer is modulo the cyclic buffer: a displacement of d periods can mean d plus n complete iterations of the buffer. Report d, so the driver could have missed n iterations of the buffer; DMA40 has no counter to recover them. For an unchanged pointer, report one callback rather than risk a spurious full-buffer burst.

This condition has not been seen in practice and is only a product of review comments that the buffer can miss interrupts.

Quoted 7 lines

The preceding cyclic-residue fix ensures that every cyclic period fits in one LLI, so each boundary corresponds to one client callback.

Fixes 0c842b551063 ("dma40: cyclic xfer support")
Assisted-by LLM

---

Quoted 140 lines
 drivers/dma/ste_dma40.c | 69 ++++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 68 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +68 -2
index eab9c09b4bfe..4b138aa313c8 100644
@@ -384,11 +384,14 @@ struct d40_lli_pool {
  * @cyclic_dma_addr: Start address of the cyclic buffer.
  * @cyclic_buf_len: Length of the cyclic buffer.
  * @cyclic_residue: Last valid cyclic residue sample.
+ * @cyclic_period_len: Length of one cyclic period.
+ * @cyclic_callback_pos: Position after the callbacks already queued.
  * @txd: DMA engine struct. Used for among other things for communication
  * during a transfer.
  * @node: List entry.
  * @is_in_client_list: true if the client owns this descriptor.
  * @cyclic: true if this is a cyclic job
+ * @cyclic_callback_pos_valid: Whether cyclic_callback_pos is reliable.
  *
  * This descriptor is used for both logical and physical transfers.
  */
@@ -405,12 +408,15 @@ struct d40_desc {
 	dma_addr_t			 cyclic_dma_addr;
 	size_t				 cyclic_buf_len;
 	size_t				 cyclic_residue;
+	size_t				 cyclic_period_len;
+	size_t				 cyclic_callback_pos;
 
 	struct dma_async_tx_descriptor	 txd;
 	struct list_head		 node;
 
 	bool				 is_in_client_list;
 	bool				 cyclic;
+	bool				 cyclic_callback_pos_valid;
 };
 
 /**
@@ -1487,6 +1493,61 @@ static bool d40_cyclic_offset(struct d40_chan *d40c, struct d40_desc *d40d,
 	return false;
 }
 
+static unsigned int d40_cyclic_periods_elapsed(struct d40_chan *d40c,
+					       struct d40_desc *d40d)
+{
+	size_t current_pos;
+	size_t delta;
+	size_t offset;
+	unsigned int periods;
+
+	if (!d40d->cyclic_period_len)
+		return 1;
+
+	if (!d40_cyclic_offset(d40c, d40d, &offset)) {
+		d40d->cyclic_callback_pos_valid = false;
+		return 1;
+	}
+
+	current_pos = rounddown(offset, d40d->cyclic_period_len);
+	if (!d40_residue(d40c) && current_pos != offset)
+		current_pos += d40d->cyclic_period_len;
+	if (current_pos == d40d->cyclic_buf_len)
+		current_pos = 0;
+
+	if (!d40d->cyclic_callback_pos_valid) {
+		/*
+		 * The previous interrupt was reported without a pointer
+		 * sample. Resynchronize without using the stale position,
+		 * which would count that callback again.
+		 */
+		d40d->cyclic_callback_pos = current_pos;
+		d40d->cyclic_callback_pos_valid = true;
+		return 1;
+	}
+
+	/*
+	 * The pointer wraps with the cyclic buffer, so its displacement is
+	 * only the minimum number of elapsed periods. Complete buffer laps
+	 * are not observable.
+	 */
+	delta = (current_pos + d40d->cyclic_buf_len -
+		 d40d->cyclic_callback_pos) % d40d->cyclic_buf_len;
+	periods = delta / d40d->cyclic_period_len;
+	if (!periods) {
+		/*
+		 * The TC status is a single latched bit. An unchanged pointer
+		 * cannot distinguish a complete lap from a repeated interrupt,
+		 * so do not amplify it into a buffer's worth of callbacks.
+		 */
+		periods = 1;
+	}
+
+	d40d->cyclic_callback_pos = current_pos;
+
+	return periods;
+}
+
 static bool d40_tx_is_linked(struct d40_chan *d40c)
 {
 	bool is_link;
@@ -1609,6 +1670,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
 static void dma_tc_handle(struct d40_chan *d40c)
 {
 	struct d40_desc *d40d;
+	unsigned int callbacks = 1;
 
 	/* Get first active entry from list */
 	d40d = d40_first_active_get(d40c);
@@ -1633,6 +1695,8 @@ static void dma_tc_handle(struct d40_chan *d40c)
 			if (d40d->lli_current == d40d->lli_len)
 				d40d->lli_current = 0;
 		}
+
+		callbacks = d40_cyclic_periods_elapsed(d40c, d40d);
 	} else {
 		d40_lcla_free_all(d40c, d40d);
 
@@ -1653,7 +1717,7 @@ static void dma_tc_handle(struct d40_chan *d40c)
 		d40_desc_done(d40c, d40d);
 	}
 
-	d40c->pending_tx++;
+	d40c->pending_tx += callbacks;
 	tasklet_schedule(&d40c->tasklet);
 
 }
@@ -2638,6 +2702,9 @@ dma40_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr,
 		desc->cyclic_dma_addr = buf_addr;
 		desc->cyclic_buf_len = buf_len;
 		desc->cyclic_residue = buf_len;
+		desc->cyclic_period_len = period_len;
+		desc->cyclic_callback_pos = 0;
+		desc->cyclic_callback_pos_valid = true;
 	}
 
 	kfree(sg);
 
--

2.55.0

author maintainer
#5 lore raw

PATCH v7 4/24 dmaengine: ste_dma40: Fix failed start cleanup

In reply to Linus Walleij

If d40_start() fails after a queued descriptor has been moved to the active list, d40_queue_start() currently returns NULL without unwinding the transfer state or clearing the channel busy flag.

Fix this pre-existing error path by completing the descriptor through the normal tasklet path, clearing the busy flag, balancing the runtime PM reference and returning an error pointer to distinguish the failure from the no-work case. Do not free the descriptor directly, since it has already been submitted and has a DMA cookie.

When starting the next queued transfer from the completion handler, put the completed descriptor on the done list first. This preserves FIFO completion order if the new transfer fails to start and prevents the completed cookie from moving backwards.

Use done-list membership rather than the cyclic flag to identify terminal descriptors in the tasklet. A cyclic descriptor that failed to start is then completed and removed instead of remaining permanently at the head of the done list.

Fixes 7d83a854a1a4 ("dma40: remove "hardware link with previous jobs" code")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 25 +++++++++++++++++--------
 1 file changed, 17 insertions(+), 8 deletions(-)
drivers/dma/ste_dma40.c +17 -8
index 4b138aa313c8..64f7a0ca20b9 100644
@@ -1659,8 +1659,15 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
 		/* Start dma job */
 		err = d40_start(d40c);
 
-		if (err)
-			return NULL;
+		if (err) {
+			d40_desc_remove(d40d);
+			d40_desc_done(d40c, d40d);
+			d40c->pending_tx++;
+			d40c->busy = false;
+			pm_runtime_put_autosuspend(d40c->base->dev);
+			tasklet_schedule(&d40c->tasklet);
+			return ERR_PTR(err);
+		}
 	}
 
 	return d40d;
@@ -1707,14 +1714,14 @@ static void dma_tc_handle(struct d40_chan *d40c)
 			return;
 		}
 
+		d40_desc_remove(d40d);
+		d40_desc_done(d40c, d40d);
+
 		if (d40_queue_start(d40c) == NULL) {
 			d40c->busy = false;
 
 			pm_runtime_put_autosuspend(d40c->base->dev);
 		}
-
-		d40_desc_remove(d40d);
-		d40_desc_done(d40c, d40d);
 	}
 
 	d40c->pending_tx += callbacks;
@@ -1728,20 +1735,22 @@ static void dma_tasklet(struct tasklet_struct *t)
 	struct d40_desc *d40d;
 	unsigned long flags;
 	bool callback_active;
+	bool from_done;
 	struct dmaengine_desc_callback cb;
 
 	spin_lock_irqsave(&d40c->lock, flags);
 
 	/* Get first entry from the done list */
 	d40d = d40_first_done(d40c);
-	if (d40d == NULL) {
+	from_done = !!d40d;
+	if (!from_done) {
 		/* Check if we have reached here for cyclic job */
 		d40d = d40_first_active_get(d40c);
 		if (d40d == NULL || !d40d->cyclic)
 			goto check_pending_tx;
 	}
 
-	if (!d40d->cyclic)
+	if (from_done)
 		dma_cookie_complete(&d40d->txd);
 
 	/*
@@ -1757,7 +1766,7 @@ static void dma_tasklet(struct tasklet_struct *t)
 	callback_active = !!(d40d->txd.flags & DMA_PREP_INTERRUPT);
 	dmaengine_desc_get_callback(&d40d->txd, &cb);
 
-	if (!d40d->cyclic) {
+	if (from_done) {
 		if (async_tx_test_ack(&d40d->txd)) {
 			d40_desc_remove(d40d);
 			d40_desc_free(d40c, d40d);
Signature · 1 line
2.55.0
author maintainer
#6 lore raw

PATCH v7 5/24 dmaengine: ste_dma40: Fix probe runtime PM disable

In reply to Linus Walleij

Some d40_probe() error paths jump to destroy_cache before runtime PM has been enabled for the DMA controller device. The label unconditionally calls pm_runtime_disable(), which increments disable_depth even though this probe attempt never enabled runtime PM.

Use devm_pm_runtime_set_active_enabled() to mark the controller active, enable runtime PM and register balanced cleanup for probe failure. This avoids both the disable-depth imbalance and ad-hoc probe state tracking.

The interrupt handler uses pm_runtime_get_if_active() and cannot acknowledge a pending interrupt while runtime PM is disabled. Request the IRQ only after enabling runtime PM so the handler cannot enter an unacknowledged interrupt loop during probe.

Fixes 0618c077a8c2 ("dmaengine: ste_dma40: Fix PM disable depth imbalance in d40_probe")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 23 +++++++++++++----------
 1 file changed, 13 insertions(+), 10 deletions(-)
drivers/dma/ste_dma40.c +13 -10
index 64f7a0ca20b9..1dcfeabb3f36 100644
@@ -3757,12 +3757,6 @@ static int __init d40_probe(struct platform_device *pdev)
 		goto destroy_cache;
 	}
 
-	ret = request_irq(base->irq, d40_handle_interrupt, 0, D40_NAME, base);
-	if (ret) {
-		d40_err(dev, "No IRQ defined\n");
-		goto destroy_cache;
-	}
-
 	if (base->plat_data->use_esram_lcla) {
 
 		base->lcpa_regulator = regulator_get(base->dev, "lcla_esram");
@@ -3787,10 +3781,20 @@ static int __init d40_probe(struct platform_device *pdev)
 
 	pm_runtime_irq_safe(base->dev);
 	pm_runtime_set_autosuspend_delay(base->dev, DMA40_AUTOSUSPEND_DELAY);
-	pm_runtime_use_autosuspend(base->dev);
 	pm_runtime_mark_last_busy(base->dev);
-	pm_runtime_set_active(base->dev);
-	pm_runtime_enable(base->dev);
+
+	ret = devm_pm_runtime_set_active_enabled(base->dev);
+	if (ret) {
+		d40_err(dev, "Failed to enable runtime PM: %d\n", ret);
+		goto destroy_cache;
+	}
+	pm_runtime_use_autosuspend(base->dev);
+
+	ret = request_irq(base->irq, d40_handle_interrupt, 0, D40_NAME, base);
+	if (ret) {
+		d40_err(dev, "No IRQ defined\n");
+		goto destroy_cache;
+	}
 
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
@@ -3826,7 +3830,6 @@ static int __init d40_probe(struct platform_device *pdev)
 		regulator_disable(base->lcpa_regulator);
 		regulator_put(base->lcpa_regulator);
 	}
-	pm_runtime_disable(base->dev);
 
  report_failure:
 	d40_err(dev, "probe failed\n");
Signature · 1 line
2.55.0
author maintainer
#7 lore raw

PATCH v7 6/24 dmaengine: ste_dma40: Check runtime PM in IRQ

In reply to Linus Walleij

d40_handle_interrupt() reads DMA40 interrupt registers unconditionally. A spurious interrupt can arrive while the device is runtime suspended, after dma40_runtime_suspend() has disabled the GCC clock.

Avoid touching the registers unless the device is runtime active by taking a conditional runtime PM reference. Return IRQ_NONE when the device is suspended, and drop the reference after handling an active interrupt.

When CONFIG_PM is disabled, pm_runtime_get_if_active() returns -EINVAL even though the registers remain accessible. Keep handling interrupts in that configuration and only drop the runtime PM reference when one was acquired.

Fixes 7fb3e75e1833 ("dmaengine/ste_dma40: support pm in dma40")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/dma/ste_dma40.c +8 -0
index 1dcfeabb3f36..5e9b6342c5a9 100644
@@ -1807,6 +1807,11 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)
 	u32 *regs = base->regs_interrupt;
 	struct d40_interrupt_lookup *il = base->gen_dmac.il;
 	u32 il_size = base->gen_dmac.il_size;
+	int ret;
+
+	ret = pm_runtime_get_if_active(base->dev);
+	if (IS_ENABLED(CONFIG_PM) && ret <= 0)
+		return IRQ_NONE;
 
 	spin_lock(&base->interrupt_lock);
 
@@ -1855,6 +1860,9 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)
 
 	spin_unlock(&base->interrupt_lock);
 
+	if (ret > 0)
+		pm_runtime_put_autosuspend(base->dev);
+
 	return IRQ_HANDLED;
 }
 
Signature · 1 line
2.55.0
#8 lore raw

Re: [PATCH v7 06/24] dmaengine: ste_dma40: Check runtime PM in IRQ

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider: - [High] dmaengine: ste_dma40: IRQ storm due to unhandled interrupt during RPM_RESUMING --

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [High] dmaengine: ste_dma40: IRQ storm due to unhandled interrupt during RPM_RESUMING --

commit 5c375e7c3c832d3f8400ed368962408e5da22738
Author: Linus Walleij <[email protected]>

dmaengine: ste_dma40: Check runtime PM in IRQ

d40_handle_interrupt() reads DMA40 interrupt registers unconditionally. A spurious interrupt can arrive while the device is runtime suspended, after dma40_runtime_suspend() has disabled the GCC clock. Avoid touching the registers unless the device is runtime active by taking a conditional runtime PM reference.

drivers/dma/ste_dma40.c static irqreturn_t d40_handle_interrupt(int irq, void *data) · line 1814

Quoted 13 lines
drivers/dma/ste_dma40.c +5 -0
index 1dcfeabb3f363..5e9b6342c5a9e 100644
@@ -1807,6 +1807,11 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)
 	u32 *regs = base->regs_interrupt;
 	struct d40_interrupt_lookup *il = base->gen_dmac.il;
 	u32 il_size = base->gen_dmac.il_size;
+	int ret;
+
+	ret = pm_runtime_get_if_active(base->dev);
+	if (IS_ENABLED(CONFIG_PM) && ret <= 0)
+		return IRQ_NONE;

[Severity: High]
Does returning IRQ_NONE here cause an IRQ storm during device resume?

In dma40_runtime_resume(), the hardware clocks are enabled which immediately asserts any pending interrupts. However, the PM core's status is still RPM_RESUMING, causing pm_runtime_get_if_active() to return 0.

Because the interrupt handler skips acknowledging the hardware interrupt and returns IRQ_NONE, the level-triggered interrupt remains asserted.

A similar situation can happen during system suspend when pm_runtime_force_suspend() disables runtime PM (disable_depth > 0), causing pm_runtime_get_if_active() to return -EINVAL.

Will this cause the kernel to eventually disable the interrupt line ("nobody cared") and permanently break the DMA controller?

Signature · 1 line
Sashiko AI review · https://sashiko.dev/#/patchset/[email protected]?part=6
author maintainer
#9 lore raw

Re: [PATCH v7 06/24] dmaengine: ste_dma40: Check runtime PM in IRQ

Quoted 2 lines · On Sun, Sep 27, 2026 at 11:24 AM <[email protected]> wrote:

Will this cause the kernel to eventually disable the interrupt line ("nobody cared") and permanently break the DMA controller?

Yes that is the idea.

That is what spurious interrupt handling does.

Yours,
Linus Walleij

author maintainer
#10 lore raw

PATCH v7 7/24 dmaengine: ste_dma40: Handle runtime PM resume errors

In reply to Linus Walleij

Several channel operations use pm_runtime_get_sync() and access DMA40 registers without checking whether runtime resume succeeded. If resume fails, the registers may be inaccessible. pm_runtime_get_sync() also increments the usage counter on failure, making error unwinding easy to unbalance.

Use pm_runtime_resume_and_get() and avoid register access when resume fails. Acquire the runtime PM reference before allocating a channel so failure needs no channel-allocation rollback.

If a queued transfer cannot be started because resume failed, retire all issued descriptors through the normal tasklet path. Since dma_async_issue_pending() cannot return an error, leaving them queued would make clients wait indefinitely for callbacks.

Termination and channel release must also clean up software state when the controller cannot resume. d40_term_all() only releases descriptor state and does not access DMA40 registers, so it remains unconditional.

Balance each transient runtime PM reference in its successful acquisition block, without bookkeeping flags. Release the outstanding busy reference and channel allocation state when freeing a channel. Skip only the hardware stop that requires register access.

Fixes 7fb3e75e1833 ("dmaengine/ste_dma40: support pm in dma40")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 74 ++++++++++++++++++++++++++++++++++---------------
 1 file changed, 52 insertions(+), 22 deletions(-)
drivers/dma/ste_dma40.c +52 -22
index 5e9b6342c5a9..80780f76dff0 100644
@@ -1576,11 +1576,14 @@ static int d40_pause(struct dma_chan *chan)
 		return 0;
 
 	spin_lock_irqsave(&d40c->lock, flags);
-	pm_runtime_get_sync(d40c->base->dev);
+	res = pm_runtime_resume_and_get(d40c->base->dev);
+	if (res < 0)
+		goto unlock;
 
 	res = d40_channel_execute_command(d40c, D40_DMA_SUSPEND_REQ);
 
 	pm_runtime_put_autosuspend(d40c->base->dev);
+ unlock:
 	spin_unlock_irqrestore(&d40c->lock, flags);
 	return res;
 }
@@ -1600,13 +1603,16 @@ static int d40_resume(struct dma_chan *chan)
 		return 0;
 
 	spin_lock_irqsave(&d40c->lock, flags);
-	pm_runtime_get_sync(d40c->base->dev);
+	res = pm_runtime_resume_and_get(d40c->base->dev);
+	if (res < 0)
+		goto unlock;
 
 	/* If bytes left to transfer or linked tx resume job */
 	if (d40_residue(d40c) || d40_tx_is_linked(d40c))
 		res = d40_channel_execute_command(d40c, D40_DMA_RUN);
 
 	pm_runtime_put_autosuspend(d40c->base->dev);
+ unlock:
 	spin_unlock_irqrestore(&d40c->lock, flags);
 	return res;
 }
@@ -1643,8 +1649,20 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
 
 	if (d40d != NULL) {
 		if (!d40c->busy) {
+			err = pm_runtime_resume_and_get(d40c->base->dev);
+			if (err < 0) {
+				chan_err(d40c, "Failed to resume DMA: %d\n",
+					 err);
+				do {
+					d40_desc_remove(d40d);
+					d40_desc_done(d40c, d40d);
+					d40c->pending_tx++;
+					d40d = d40_first_queued(d40c);
+				} while (d40d);
+				tasklet_schedule(&d40c->tasklet);
+				return ERR_PTR(err);
+			}
 			d40c->busy = true;
-			pm_runtime_get_sync(d40c->base->dev);
 		}
 
 		/* Remove from queue */
@@ -2161,9 +2179,6 @@ static int d40_free_dma(struct d40_chan *d40c)
 	struct d40_phy_res *phy = d40c->phy_chan;
 	bool is_src;
 
-	/* Terminate all queued and active transfers */
-	d40_term_all(d40c);
-
 	if (phy == NULL) {
 		chan_err(d40c, "phy == null\n");
 		return -EINVAL;
@@ -2185,11 +2200,18 @@ static int d40_free_dma(struct d40_chan *d40c)
 		return -EINVAL;
 	}
 
-	pm_runtime_get_sync(d40c->base->dev);
-	res = d40_channel_execute_command(d40c, D40_DMA_STOP);
-	if (res) {
-		chan_err(d40c, "stop failed\n");
-		goto mark_last_busy;
+	/* Release descriptor state; this does not access DMA40 registers. */
+	d40_term_all(d40c);
+
+	res = pm_runtime_resume_and_get(d40c->base->dev);
+	if (res >= 0) {
+		res = d40_channel_execute_command(d40c, D40_DMA_STOP);
+		if (res)
+			chan_err(d40c, "stop failed\n");
+
+		pm_runtime_put_autosuspend(d40c->base->dev);
+		if (res)
+			return res;
 	}
 
 	d40_alloc_mask_free(phy, is_src, chan_is_logical(d40c) ? event : 0);
@@ -2205,8 +2227,6 @@ static int d40_free_dma(struct d40_chan *d40c)
 	d40c->busy = false;
 	d40c->phy_chan = NULL;
 	d40c->configured = false;
- mark_last_busy:
-	pm_runtime_put_autosuspend(d40c->base->dev);
 	return res;
 }
 
@@ -2581,10 +2601,14 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
 		err = d40_config_memcpy(d40c);
 		if (err) {
 			chan_err(d40c, "Failed to configure memcpy channel\n");
-			goto mark_last_busy;
+			goto unlock;
 		}
 	}
 
+	err = pm_runtime_resume_and_get(d40c->base->dev);
+	if (err < 0)
+		goto unlock;
+
 	err = d40_allocate_channel(d40c, &is_free_phy);
 	if (err) {
 		chan_err(d40c, "Failed to allocate channel\n");
@@ -2592,8 +2616,6 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
 		goto mark_last_busy;
 	}
 
-	pm_runtime_get_sync(d40c->base->dev);
-
 	d40_set_prio_realtime(d40c);
 
 	if (chan_is_logical(d40c)) {
@@ -2625,6 +2647,7 @@ static int d40_alloc_chan_resources(struct dma_chan *chan)
 		d40_config_write(d40c);
  mark_last_busy:
 	pm_runtime_put_autosuspend(d40c->base->dev);
+ unlock:
 	spin_unlock_irqrestore(&d40c->lock, flags);
 	return err;
 }
@@ -2785,19 +2808,26 @@ static int d40_terminate_all(struct dma_chan *chan)
 
 	spin_lock_irqsave(&d40c->lock, flags);
 
-	pm_runtime_get_sync(d40c->base->dev);
-	ret = d40_channel_execute_command(d40c, D40_DMA_STOP);
-	if (ret)
-		chan_err(d40c, "Failed to stop channel\n");
+	ret = pm_runtime_resume_and_get(d40c->base->dev);
+	if (ret >= 0) {
+		ret = d40_channel_execute_command(d40c, D40_DMA_STOP);
+		if (ret)
+			chan_err(d40c, "Failed to stop channel\n");
+
+		pm_runtime_put_autosuspend(d40c->base->dev);
+	}
 
+	/*
+	 * Always release software state, even when the controller cannot
+	 * resume. d40_term_all() does not access DMA40 registers.
+	 */
 	d40_term_all(d40c);
-	pm_runtime_put_autosuspend(d40c->base->dev);
 	if (d40c->busy)
 		pm_runtime_put_autosuspend(d40c->base->dev);
 	d40c->busy = false;
 
 	spin_unlock_irqrestore(&d40c->lock, flags);
-	return 0;
+	return ret;
 }
 
 static int
Signature · 1 line
2.55.0
author maintainer
#11 lore raw

PATCH v7 8/24 dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending

In reply to Linus Walleij

d40_handle_interrupt() returns IRQ_HANDLED even when no terminal-count or error status bit is pending.

IRQ_NONE is not only used to identify a device on a shared interrupt. The generic IRQ core also counts it as unhandled for spurious IRQ detection. DMA40 does not request this IRQ with IRQF_SHARED, so interrupt sharing is not the purpose of this change.

If the line remains asserted without matching DMA40 status, returning IRQ_HANDLED hides the stuck interrupt and can leave the CPU servicing it indefinitely. Track whether any DMA40 status is pending and return IRQ_NONE when none is present, allowing the generic IRQ core to diagnose and eventually disable the faulty line.

DMA40 channels can be owned by other SoC cores. Their status means that the interrupt is real, but Linux must not acknowledge it. Treat foreign status as handled and leave its acknowledgment to the owning core, while acknowledging and dispatching only registered Linux channels.

Fixes 8d318a50b3d7 ("DMAENGINE: Support for ST-Ericssons DMA40 block v3")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +8 -1
index 80780f76dff0..86efe2149be9 100644
@@ -1816,6 +1816,7 @@ static void dma_tasklet(struct tasklet_struct *t)
 
 static irqreturn_t d40_handle_interrupt(int irq, void *data)
 {
+	irqreturn_t handled = IRQ_NONE;
 	int i;
 	u32 idx;
 	u32 row;
@@ -1849,6 +1850,12 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)
 		row = chan / BITS_PER_LONG;
 		idx = chan & (BITS_PER_LONG - 1);
 
+		/*
+		 * Status for a channel owned by another core still explains
+		 * the interrupt, but only ACK Linux-owned channels below.
+		 */
+		handled = IRQ_HANDLED;
+
 		if (il[row].offset == D40_PHY_CHAN)
 			d40c = base->lookup_phy_chans[idx];
 		else
@@ -1881,7 +1888,7 @@ static irqreturn_t d40_handle_interrupt(int irq, void *data)
 	if (ret > 0)
 		pm_runtime_put_autosuspend(base->dev);
 
-	return IRQ_HANDLED;
+	return handled;
 }
 
 static int d40_validate_conf(struct d40_chan *d40c,
Signature · 1 line
2.55.0
author maintainer
#12 lore raw

PATCH v7 9/24 dmaengine: ste_dma40: Init hardware before registration

In reply to Linus Walleij

d40_probe() enables the interrupt handler and registers DMAengine devices before calling d40_hw_init(). An interrupt pending from the bootloader can therefore reach the handler while the hardware interrupt state is not initialized and channel lookup entries are empty. The handler deliberately does not acknowledge an interrupt for an unknown channel, so a level IRQ can retrigger continuously.

Initialize the hardware and set the DMA segment limit before requesting the IRQ or registering DMAengine devices. d40_hw_init() clears pending logical and physical interrupt status, so request_irq() can enable the line normally after the hardware state is initialized.

This ensures that the handler and clients only observe initialized hardware.

Fixes 8d318a50b3d7 ("DMAENGINE: Support for ST-Ericssons DMA40 block v3")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +4 -5
index 86efe2149be9..3bf89b057ccf 100644
@@ -3835,20 +3835,19 @@ static int __init d40_probe(struct platform_device *pdev)
 	}
 	pm_runtime_use_autosuspend(base->dev);
 
+	dma_set_max_seg_size(base->dev, STEDMA40_MAX_SEG_SIZE);
+
+	d40_hw_init(base);
+
 	ret = request_irq(base->irq, d40_handle_interrupt, 0, D40_NAME, base);
 	if (ret) {
 		d40_err(dev, "No IRQ defined\n");
 		goto destroy_cache;
 	}
-
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
 		goto destroy_cache;
 
-	dma_set_max_seg_size(base->dev, STEDMA40_MAX_SEG_SIZE);
-
-	d40_hw_init(base);
-
 	ret = of_dma_controller_register(np, d40_xlate, NULL);
 	if (ret) {
 		dev_err(dev,
Signature · 1 line
2.55.0
Reviewed-by on v7 9/24
#13 lore raw

Re: [PATCH v7 09/24] dmaengine: ste_dma40: Init hardware before registration

Quoted 15 lines · Linus Walleij

d40_probe() enables the interrupt handler and registers DMAengine devices before calling d40_hw_init(). An interrupt pending from the bootloader can therefore reach the handler while the hardware interrupt state is not initialized and channel lookup entries are empty. The handler deliberately does not acknowledge an interrupt for an unknown channel, so a level IRQ can retrigger continuously.

Initialize the hardware and set the DMA segment limit before requesting the IRQ or registering DMAengine devices. d40_hw_init() clears pending logical and physical interrupt status, so request_irq() can enable the line normally after the hardware state is initialized.

This ensures that the handler and clients only observe initialized hardware.

Quoted 6 lines
Fixes 8d318a50b3d7 ("DMAENGINE: Support for ST-Ericssons DMA40 block v3")
Reported-by [email protected]
Assisted-by LLM

---

Quoted 36 lines
 drivers/dma/ste_dma40.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +4 -6
index 86efe2149be9..3bf89b057ccf 100644
@@ -3835,20 +3835,19 @@ static int __init d40_probe(struct platform_device *pdev)
 	}
 	pm_runtime_use_autosuspend(base->dev);
 
+	dma_set_max_seg_size(base->dev, STEDMA40_MAX_SEG_SIZE);
+
+	d40_hw_init(base);
+
 	ret = request_irq(base->irq, d40_handle_interrupt, 0, D40_NAME, base);
 	if (ret) {
 		d40_err(dev, "No IRQ defined\n");
 		goto destroy_cache;
 	}
-
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
 		goto destroy_cache;
 
-	dma_set_max_seg_size(base->dev, STEDMA40_MAX_SEG_SIZE);
-
-	d40_hw_init(base);
-
 	ret = of_dma_controller_register(np, d40_xlate, NULL);
 	if (ret) {
 		dev_err(dev,
 
--

2.55.0

author maintainer
#14 lore raw

PATCH v7 10/24 dmaengine: ste_dma40: Fix probe IRQ leak

In reply to Linus Walleij

d40_probe() registers the hardware interrupt before several later probe steps that can fail. Those error paths jump to destroy_cache without freeing the IRQ, leaving the handler registered after probe resources have been released.

Route failures after a successful IRQ request through a dedicated cleanup label. Keep the request before DMAengine registration because that registration publishes channels to clients.

Fixes 8d318a50b3d7 ("DMAENGINE: Support for ST-Ericssons DMA40 block v3")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/dma/ste_dma40.c +4 -2
index 3bf89b057ccf..4c545a947264 100644
@@ -3846,18 +3846,20 @@ static int __init d40_probe(struct platform_device *pdev)
 	}
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
-		goto destroy_cache;
+		goto release_irq;
 
 	ret = of_dma_controller_register(np, d40_xlate, NULL);
 	if (ret) {
 		dev_err(dev,
 			"could not register of_dma_controller\n");
-		goto destroy_cache;
+		goto release_irq;
 	}
 
 	dev_info(base->dev, "initialized\n");
 	return 0;
 
+ release_irq:
+	free_irq(base->irq, base);
  destroy_cache:
 	if (base->lcla_pool.dma_addr)
 		dma_unmap_single(base->dev, base->lcla_pool.dma_addr,
Signature · 1 line
2.55.0
Reviewed-by on v7 10/24
#15 lore raw

Re: [PATCH v7 10/24] dmaengine: ste_dma40: Fix probe IRQ leak

Quoted 9 lines · Linus Walleij

d40_probe() registers the hardware interrupt before several later probe steps that can fail. Those error paths jump to destroy_cache without freeing the IRQ, leaving the handler registered after probe resources have been released.

Route failures after a successful IRQ request through a dedicated cleanup label. Keep the request before DMAengine registration because that registration publishes channels to clients.

Quoted 6 lines
Fixes 8d318a50b3d7 ("DMAENGINE: Support for ST-Ericssons DMA40 block v3")
Reported-by [email protected]
Assisted-by LLM

---

Quoted 34 lines
 drivers/dma/ste_dma40.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/dma/ste_dma40.c +4 -3
index 3bf89b057ccf..4c545a947264 100644
@@ -3846,18 +3846,20 @@ static int __init d40_probe(struct platform_device *pdev)
 	}
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
-		goto destroy_cache;
+		goto release_irq;
 
 	ret = of_dma_controller_register(np, d40_xlate, NULL);
 	if (ret) {
 		dev_err(dev,
 			"could not register of_dma_controller\n");
-		goto destroy_cache;
+		goto release_irq;
 	}
 
 	dev_info(base->dev, "initialized\n");
 	return 0;
 
+ release_irq:
+	free_irq(base->irq, base);
  destroy_cache:
 	if (base->lcla_pool.dma_addr)
 		dma_unmap_single(base->dev, base->lcla_pool.dma_addr,
 
--

2.55.0

author maintainer
#16 lore raw

PATCH v7 11/24 dmaengine: ste_dma40: Fix DMA registration unwind

In reply to Linus Walleij

d40_dmaengine_init() registers DMAengine devices using devres-managed unregister actions. If probe fails after one of those registrations, the DMAengine devices stay visible until devres unwinds after d40_probe() returns.

The channel tasklets are also initialized before each DMAengine device is registered. An interrupt can therefore have queued a tasklet by the time a later registration step fails, but unregistering the DMAengine devices does not drain that tasklet before probe-owned storage is released.

Add tasklet cleanup actions to the DMAengine registration devres group. Install each action before publishing its DMAengine device. If action registration fails, those tasklets have never been exposed and cannot have been scheduled, so use devm_add_action() without immediate reset cleanup.

On later failure, free the IRQ before releasing the group so no new tasklets can be scheduled, then unregister the DMAengine devices and drain their tasklets before freeing the remaining probe resources. Keep the managed registrations and cleanup actions in place on successful probe by removing only the temporary group markers.

Fixes 42ae6f1695be ("dmaengine: ste_dma40: Remove platform data")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 45 +++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 43 insertions(+), 2 deletions(-)
drivers/dma/ste_dma40.c +43 -2
index 4c545a947264..f72d91c8d0fa 100644
@@ -3039,6 +3039,18 @@ static void __init d40_chan_init(struct d40_base *base, struct dma_device *dma,
 	}
 }
 
+static void d40_kill_tasklets(void *data)
+{
+	struct dma_device *dma = data;
+	struct d40_chan *d40c;
+	struct dma_chan *chan;
+
+	list_for_each_entry(chan, &dma->channels, device_node) {
+		d40c = container_of(chan, struct d40_chan, chan);
+		tasklet_kill(&d40c->tasklet);
+	}
+}
+
 static void d40_ops_init(struct d40_base *base, struct dma_device *dev)
 {
 	if (dma_has_cap(DMA_SLAVE, dev->cap_mask)) {
@@ -3085,6 +3097,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 
 	d40_ops_init(base, &base->dma_slave);
 
+	err = devm_add_action(base->dev, d40_kill_tasklets,
+			      &base->dma_slave);
+	if (err)
+		goto exit;
+
 	err = dmaenginem_async_device_register(&base->dma_slave);
 
 	if (err) {
@@ -3100,6 +3117,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 
 	d40_ops_init(base, &base->dma_memcpy);
 
+	err = devm_add_action(base->dev, d40_kill_tasklets,
+			      &base->dma_memcpy);
+	if (err)
+		goto exit;
+
 	err = dmaenginem_async_device_register(&base->dma_memcpy);
 
 	if (err) {
@@ -3117,6 +3139,12 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 	dma_cap_set(DMA_CYCLIC, base->dma_both.cap_mask);
 
 	d40_ops_init(base, &base->dma_both);
+
+	err = devm_add_action(base->dev, d40_kill_tasklets,
+			      &base->dma_both);
+	if (err)
+		goto exit;
+
 	err = dmaenginem_async_device_register(&base->dma_both);
 
 	if (err) {
@@ -3714,6 +3742,7 @@ static int __init d40_probe(struct platform_device *pdev)
 	struct d40_base *base;
 	struct resource *res;
 	struct resource res_lcpa;
+	void *dmaenginem_reg_group;
 	int num_reserved_chans;
 	u32 val;
 	int ret;
@@ -3844,20 +3873,32 @@ static int __init d40_probe(struct platform_device *pdev)
 		d40_err(dev, "No IRQ defined\n");
 		goto destroy_cache;
 	}
+
+	dmaenginem_reg_group = devres_open_group(dev, NULL, GFP_KERNEL);
+	if (!dmaenginem_reg_group) {
+		ret = -ENOMEM;
+		goto release_irq;
+	}
+
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
-		goto release_irq;
+		goto release_dmaenginem;
 
 	ret = of_dma_controller_register(np, d40_xlate, NULL);
 	if (ret) {
 		dev_err(dev,
 			"could not register of_dma_controller\n");
-		goto release_irq;
+		goto release_dmaenginem;
 	}
+	devres_remove_group(dev, dmaenginem_reg_group);
 
 	dev_info(base->dev, "initialized\n");
 	return 0;
 
+ release_dmaenginem:
+	free_irq(base->irq, base);
+	devres_release_group(dev, dmaenginem_reg_group);
+	goto destroy_cache;
  release_irq:
 	free_irq(base->irq, base);
  destroy_cache:
Signature · 1 line
2.55.0
Reviewed-by on v7 11/24
#17 lore raw

Re: [PATCH v7 11/24] dmaengine: ste_dma40: Fix DMA registration unwind

Quoted 21 lines · Linus Walleij

d40_dmaengine_init() registers DMAengine devices using devres-managed unregister actions. If probe fails after one of those registrations, the DMAengine devices stay visible until devres unwinds after d40_probe() returns.

The channel tasklets are also initialized before each DMAengine device is registered. An interrupt can therefore have queued a tasklet by the time a later registration step fails, but unregistering the DMAengine devices does not drain that tasklet before probe-owned storage is released.

Add tasklet cleanup actions to the DMAengine registration devres group. Install each action before publishing its DMAengine device. If action registration fails, those tasklets have never been exposed and cannot have been scheduled, so use devm_add_action() without immediate reset cleanup.

On later failure, free the IRQ before releasing the group so no new tasklets can be scheduled, then unregister the DMAengine devices and drain their tasklets before freeing the remaining probe resources. Keep the managed registrations and cleanup actions in place on successful probe by removing only the temporary group markers.

Quoted 6 lines
Fixes 42ae6f1695be ("dmaengine: ste_dma40: Remove platform data")
Reported-by [email protected]
Assisted-by LLM

---

Quoted 110 lines
 drivers/dma/ste_dma40.c | 45 +++++++++++++++++++++++++++++++++++++++++++--
 1 file changed, 43 insertions(+), 2 deletions(-)
drivers/dma/ste_dma40.c +43 -3
index 4c545a947264..f72d91c8d0fa 100644
@@ -3039,6 +3039,18 @@ static void __init d40_chan_init(struct d40_base *base, struct dma_device *dma,
 	}
 }
 
+static void d40_kill_tasklets(void *data)
+{
+	struct dma_device *dma = data;
+	struct d40_chan *d40c;
+	struct dma_chan *chan;
+
+	list_for_each_entry(chan, &dma->channels, device_node) {
+		d40c = container_of(chan, struct d40_chan, chan);
+		tasklet_kill(&d40c->tasklet);
+	}
+}
+
 static void d40_ops_init(struct d40_base *base, struct dma_device *dev)
 {
 	if (dma_has_cap(DMA_SLAVE, dev->cap_mask)) {
@@ -3085,6 +3097,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 
 	d40_ops_init(base, &base->dma_slave);
 
+	err = devm_add_action(base->dev, d40_kill_tasklets,
+			      &base->dma_slave);
+	if (err)
+		goto exit;
+
 	err = dmaenginem_async_device_register(&base->dma_slave);
 
 	if (err) {
@@ -3100,6 +3117,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 
 	d40_ops_init(base, &base->dma_memcpy);
 
+	err = devm_add_action(base->dev, d40_kill_tasklets,
+			      &base->dma_memcpy);
+	if (err)
+		goto exit;
+
 	err = dmaenginem_async_device_register(&base->dma_memcpy);
 
 	if (err) {
@@ -3117,6 +3139,12 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 	dma_cap_set(DMA_CYCLIC, base->dma_both.cap_mask);
 
 	d40_ops_init(base, &base->dma_both);
+
+	err = devm_add_action(base->dev, d40_kill_tasklets,
+			      &base->dma_both);
+	if (err)
+		goto exit;
+
 	err = dmaenginem_async_device_register(&base->dma_both);
 
 	if (err) {
@@ -3714,6 +3742,7 @@ static int __init d40_probe(struct platform_device *pdev)
 	struct d40_base *base;
 	struct resource *res;
 	struct resource res_lcpa;
+	void *dmaenginem_reg_group;
 	int num_reserved_chans;
 	u32 val;
 	int ret;
@@ -3844,20 +3873,32 @@ static int __init d40_probe(struct platform_device *pdev)
 		d40_err(dev, "No IRQ defined\n");
 		goto destroy_cache;
 	}
+
+	dmaenginem_reg_group = devres_open_group(dev, NULL, GFP_KERNEL);
+	if (!dmaenginem_reg_group) {
+		ret = -ENOMEM;
+		goto release_irq;
+	}
+
 	ret = d40_dmaengine_init(base, num_reserved_chans);
 	if (ret)
-		goto release_irq;
+		goto release_dmaenginem;
 
 	ret = of_dma_controller_register(np, d40_xlate, NULL);
 	if (ret) {
 		dev_err(dev,
 			"could not register of_dma_controller\n");
-		goto release_irq;
+		goto release_dmaenginem;
 	}
+	devres_remove_group(dev, dmaenginem_reg_group);
 
 	dev_info(base->dev, "initialized\n");
 	return 0;
 
+ release_dmaenginem:
+	free_irq(base->irq, base);
+	devres_release_group(dev, dmaenginem_reg_group);
+	goto destroy_cache;
  release_irq:
 	free_irq(base->irq, base);
  destroy_cache:
 
--

2.55.0

author maintainer
#18 lore raw

PATCH v7 12/24 dmaengine: ste_dma40: Fix LCLA allocation order

In reply to Linus Walleij

d40_lcla_allocate() calculates the number of pages needed for LCLA, but passes that raw page count as the allocation order to __get_free_pages(). The same value is later passed to free_pages().

Store the allocation order with get_order() instead, and use a separate byte size for allocation diagnostics, fallback kmalloc() sizing and DMA mapping.

Fixes 508849ade23c ("DMAENGINE: ste_dma40: allocate LCLA dynamically")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 33 ++++++++++++++++-----------------
 1 file changed, 16 insertions(+), 17 deletions(-)
drivers/dma/ste_dma40.c +16 -17
index f72d91c8d0fa..58bc08c2ed0f 100644
@@ -426,8 +426,8 @@ struct d40_desc {
  * @dma_addr: DMA address, if mapped
  * @base_unaligned: The original kmalloc pointer, if kmalloc is used.
  * This pointer is only there for clean-up on error.
- * @pages: The number of pages needed for all physical channels.
- * Only used later for clean-up on error
+ * @alloc_order: Order used for the LCLA page allocation.
+ * Only used later for clean-up on error.
  * @lock: Lock to protect the content in this struct.
  * @alloc_map: big map over which LCLA entry is own by which job.
  */
@@ -435,7 +435,7 @@ struct d40_lcla_pool {
 	void		*base;
 	dma_addr_t	dma_addr;
 	void		*base_unaligned;
-	int		 pages;
+	unsigned int	 alloc_order;
 	spinlock_t	 lock;
 	struct d40_desc	**alloc_map;
 };
@@ -3603,6 +3603,7 @@ static void __init d40_hw_init(struct d40_base *base)
 static int __init d40_lcla_allocate(struct d40_base *base)
 {
 	struct d40_lcla_pool *pool = &base->lcla_pool;
+	size_t lcla_size = SZ_1K * base->num_phy_chans;
 	unsigned long *page_list;
 	int i, j;
 	int ret;
@@ -3618,20 +3619,20 @@ static int __init d40_lcla_allocate(struct d40_base *base)
 	if (!page_list)
 		return -ENOMEM;
 
-	/* Calculating how many pages that are required */
-	base->lcla_pool.pages = SZ_1K * base->num_phy_chans / PAGE_SIZE;
+	base->lcla_pool.alloc_order = get_order(lcla_size);
 
 	for (i = 0; i < MAX_LCLA_ALLOC_ATTEMPTS; i++) {
 		page_list[i] = __get_free_pages(GFP_KERNEL,
-						base->lcla_pool.pages);
+						base->lcla_pool.alloc_order);
 		if (!page_list[i]) {
 
-			d40_err(base->dev, "Failed to allocate %d pages.\n",
-				base->lcla_pool.pages);
+			d40_err(base->dev, "Failed to allocate %zu bytes.\n",
+				lcla_size);
 			ret = -ENOMEM;
 
 			for (j = 0; j < i; j++)
-				free_pages(page_list[j], base->lcla_pool.pages);
+				free_pages(page_list[j],
+					   base->lcla_pool.alloc_order);
 			goto free_page_list;
 		}
 
@@ -3641,7 +3642,7 @@ static int __init d40_lcla_allocate(struct d40_base *base)
 	}
 
 	for (j = 0; j < i; j++)
-		free_pages(page_list[j], base->lcla_pool.pages);
+		free_pages(page_list[j], base->lcla_pool.alloc_order);
 
 	if (i < MAX_LCLA_ALLOC_ATTEMPTS) {
 		base->lcla_pool.base = (void *)page_list[i];
@@ -3651,10 +3652,9 @@ static int __init d40_lcla_allocate(struct d40_base *base)
 		 * alignment, try with allocating a big buffer.
 		 */
 		dev_warn(base->dev,
-			 "[%s] Failed to get %d pages @ 18 bit align.\n",
-			 __func__, base->lcla_pool.pages);
-		base->lcla_pool.base_unaligned = kmalloc(SZ_1K *
-							 base->num_phy_chans +
+			 "[%s] Failed to get %zu bytes @ 18 bit align.\n",
+			 __func__, lcla_size);
+		base->lcla_pool.base_unaligned = kmalloc(lcla_size +
 							 LCLA_ALIGNMENT,
 							 GFP_KERNEL);
 		if (!base->lcla_pool.base_unaligned) {
@@ -3666,8 +3666,7 @@ static int __init d40_lcla_allocate(struct d40_base *base)
 						 LCLA_ALIGNMENT);
 	}
 
-	pool->dma_addr = dma_map_single(base->dev, pool->base,
-					SZ_1K * base->num_phy_chans,
+	pool->dma_addr = dma_map_single(base->dev, pool->base, lcla_size,
 					DMA_TO_DEVICE);
 	if (dma_mapping_error(base->dev, pool->dma_addr)) {
 		pool->dma_addr = 0;
@@ -3909,7 +3908,7 @@ static int __init d40_probe(struct platform_device *pdev)
 
 	if (!base->lcla_pool.base_unaligned && base->lcla_pool.base)
 		free_pages((unsigned long)base->lcla_pool.base,
-			   base->lcla_pool.pages);
+			   base->lcla_pool.alloc_order);
 
 	kfree(base->lcla_pool.base_unaligned);
 
Signature · 1 line
2.55.0
author maintainer
#19 lore raw

PATCH v7 13/24 dmaengine: ste_dma40: Fix probe LCLA free

In reply to Linus Walleij

When LCLA is placed in ESRAM, d40_probe() stores a devm_ioremap() address in lcla_pool.base and leaves base_unaligned unset. The destroy_cache error path can then pass the ioremap address to free_pages().

Only free lcla_pool.base with free_pages() when the driver allocated the LCLA pool from normal memory. The ESRAM mapping is devm-managed.

Fixes 339f5041089a ("dmaengine: ste_dma40: Use managed resources")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +2 -1
index 58bc08c2ed0f..e3756d8edc61 100644
@@ -3906,7 +3906,8 @@ static int __init d40_probe(struct platform_device *pdev)
 				 SZ_1K * base->num_phy_chans,
 				 DMA_TO_DEVICE);
 
-	if (!base->lcla_pool.base_unaligned && base->lcla_pool.base)
+	if (!base->plat_data->use_esram_lcla &&
+	    !base->lcla_pool.base_unaligned && base->lcla_pool.base)
 		free_pages((unsigned long)base->lcla_pool.base,
 			   base->lcla_pool.alloc_order);
 
Signature · 1 line
2.55.0
author maintainer
#20 lore raw

PATCH v7 14/24 dmaengine: ste_dma40: Put the LCPA SRAM node

In reply to Linus Walleij

of_parse_phandle() takes a reference to the LCPA SRAM node, but d40_probe() does not release it after translating the node into a resource. This leaks the node reference for the lifetime of the system.

Put the node immediately after of_address_to_resource() so both the success and error paths release the reference.

Fixes 5a1a3b9c19dd ("dmaengine: ste_dma40: Get LCPA SRAM from SRAM node")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 1 +
 1 file changed, 1 insertion(+)
drivers/dma/ste_dma40.c +1 -0
index e3756d8edc61..70f2a6594945 100644
@@ -3771,6 +3771,7 @@ static int __init d40_probe(struct platform_device *pdev)
 	}
 	/* This is no device so read the address directly from the node */
 	ret = of_address_to_resource(np_lcpa, 0, &res_lcpa);
+	of_node_put(np_lcpa);
 	if (ret) {
 		dev_err(dev, "no LCPA SRAM resource\n");
 		goto report_failure;
Signature · 1 line
2.55.0
author maintainer
#21 lore raw

PATCH v7 15/24 dmaengine: ste_dma40: Fix memcpy channel parsing

In reply to Linus Walleij

d40_of_probe() validates the memcpy-channels property against D40_MEMCPY_MAX_CHANS, but reads the property directly into a smaller global array. A long property can therefore overwrite adjacent data. The mutable global also lets a later DMA40 instance replace the memcpy channel mapping used for future allocations on an earlier instance.

Store the mapping in the per-device platform data, validate the property against that storage, and check the property read result. The property is required and d40_probe() always populates the platform data, so remove the obsolete global mapping and fallback.

Fixes a7dacb68b35a ("dmaengine: ste_dma40: Allow memcpy channels to be configured from DT")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 45 ++++++++++++++-------------------------------
 1 file changed, 14 insertions(+), 31 deletions(-)
drivers/dma/ste_dma40.c +14 -31
index 70f2a6594945..43a6ded6aa09 100644
@@ -28,6 +28,8 @@
 #include "ste_dma40.h"
 #include "ste_dma40_ll.h"
 
+#define D40_MEMCPY_MAX_CHANS	8
+
 /**
  * struct stedma40_platform_data - Configuration struct for the dma device.
  *
@@ -41,6 +43,7 @@
  * to use SoftLLI.
  * @use_esram_lcla: flag for mapping the lcla into esram region
  * @num_of_memcpy_chans: The number of channels reserved for memcpy.
+ * @memcpy_channels: The event lines used for memcpy.
  * @num_of_phy_chans: The number of physical channels implemented in HW.
  * 0 means reading the number of channels from DMA HW but this is only valid
  * for 'multiple of 4' channels, like 8.
@@ -51,6 +54,7 @@ struct stedma40_platform_data {
 	int				 num_of_soft_lli_chans;
 	bool				 use_esram_lcla;
 	int				 num_of_memcpy_chans;
+	u32				 memcpy_channels[D40_MEMCPY_MAX_CHANS];
 	int				 num_of_phy_chans;
 };
 
@@ -89,25 +93,6 @@ struct stedma40_platform_data {
 #define D40_ALLOC_PHY		BIT(30)
 #define D40_ALLOC_LOG_FREE	0
 
-#define D40_MEMCPY_MAX_CHANS	8
-
-/* Reserved event lines for memcpy only. */
-#define DB8500_DMA_MEMCPY_EV_0	51
-#define DB8500_DMA_MEMCPY_EV_1	56
-#define DB8500_DMA_MEMCPY_EV_2	57
-#define DB8500_DMA_MEMCPY_EV_3	58
-#define DB8500_DMA_MEMCPY_EV_4	59
-#define DB8500_DMA_MEMCPY_EV_5	60
-
-static int dma40_memcpy_channels[] = {
-	DB8500_DMA_MEMCPY_EV_0,
-	DB8500_DMA_MEMCPY_EV_1,
-	DB8500_DMA_MEMCPY_EV_2,
-	DB8500_DMA_MEMCPY_EV_3,
-	DB8500_DMA_MEMCPY_EV_4,
-	DB8500_DMA_MEMCPY_EV_5,
-};
-
 /* Default configuration for physical memcpy */
 static const struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
 	.mode = STEDMA40_MODE_PHYSICAL,
@@ -2154,7 +2139,8 @@ static int d40_config_memcpy(struct d40_chan *d40c)
 
 	if (dma_has_cap(DMA_MEMCPY, cap) && !dma_has_cap(DMA_SLAVE, cap)) {
 		d40c->dma_cfg = dma40_memcpy_conf_log;
-		d40c->dma_cfg.dev_type = dma40_memcpy_channels[d40c->chan.chan_id];
+		d40c->dma_cfg.dev_type =
+			d40c->base->plat_data->memcpy_channels[d40c->chan.chan_id];
 
 		d40_log_cfg(&d40c->dma_cfg,
 			    &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
@@ -3434,12 +3420,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev,
 	num_phy_chans = min(num_phy_chans, STEDMA40_MAX_PHYS);
 
 	/* The number of channels used for memcpy */
-	if (plat_data->num_of_memcpy_chans)
-		num_memcpy_chans = plat_data->num_of_memcpy_chans;
-	else
-		num_memcpy_chans = ARRAY_SIZE(dma40_memcpy_channels);
-
-	num_memcpy_chans = min(num_memcpy_chans, D40_MEMCPY_MAX_CHANS);
+	num_memcpy_chans = plat_data->num_of_memcpy_chans;
 	num_log_chans = num_phy_chans * D40_MAX_LOG_CHAN_PER_PHY;
 
 	dev_info(dev,
@@ -3688,6 +3669,7 @@ static int __init d40_of_probe(struct device *dev,
 	struct stedma40_platform_data *pdata;
 	int num_phy = 0, num_memcpy = 0, num_disabled = 0;
 	const __be32 *list;
+	int ret;
 
 	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata)
@@ -3701,18 +3683,19 @@ static int __init d40_of_probe(struct device *dev,
 	list = of_get_property(np, "memcpy-channels", &num_memcpy);
 	num_memcpy /= sizeof(*list);
 
-	if (num_memcpy > D40_MEMCPY_MAX_CHANS || num_memcpy <= 0) {
+	if (num_memcpy > ARRAY_SIZE(pdata->memcpy_channels) ||
+	    num_memcpy <= 0) {
 		d40_err(dev,
 			"Invalid number of memcpy channels specified (%d)\n",
 			num_memcpy);
 		return -EINVAL;
 	}
+	ret = of_property_read_u32_array(np, "memcpy-channels",
+					 pdata->memcpy_channels, num_memcpy);
+	if (ret)
+		return ret;
 	pdata->num_of_memcpy_chans = num_memcpy;
 
-	of_property_read_u32_array(np, "memcpy-channels",
-				   dma40_memcpy_channels,
-				   num_memcpy);
-
 	list = of_get_property(np, "disabled-channels", &num_disabled);
 	num_disabled /= sizeof(*list);
 
Signature · 1 line
2.55.0
author maintainer
#22 lore raw

PATCH v7 16/24 dmaengine: ste_dma40: Validate disabled channel indexes

In reply to Linus Walleij

d40_of_probe() checks how many entries disabled-channels contains, but not the channel numbers themselves. d40_phy_res_init() later uses every value as an index into base->phy_res, whose size is the number of channels found in this DMA40 instance. An out-of-range value can therefore write beyond the allocation.

Validate each disabled channel against the detected hardware channel count before allocating and initializing the channel resources.

Fixes 499c2bc3cc89 ("dmaengine: ste_dma40: Fetch disabled channels from DT")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/dma/ste_dma40.c +9 -0
index 43a6ded6aa09..32dd63a2c27a 100644
@@ -3419,6 +3419,15 @@ static int __init d40_hw_detect_init(struct platform_device *pdev,
 
 	num_phy_chans = min(num_phy_chans, STEDMA40_MAX_PHYS);
 
+	for (i = 0; plat_data->disabled_channels[i] != -1; i++) {
+		int chan = plat_data->disabled_channels[i];
+
+		if (chan < 0 || chan >= num_phy_chans) {
+			dev_err(dev, "Invalid disabled channel %d\n", chan);
+			return -EINVAL;
+		}
+	}
+
 	/* The number of channels used for memcpy */
 	num_memcpy_chans = plat_data->num_of_memcpy_chans;
 	num_log_chans = num_phy_chans * D40_MAX_LOG_CHAN_PER_PHY;
Signature · 1 line
2.55.0
author maintainer
#23 lore raw

PATCH v7 17/24 dmaengine: ste_dma40: Validate DMA specifier length

In reply to Linus Walleij

The DMA40 binding requires three cells, but d40_xlate() reads args[0], args[1], and args[2] without checking args_count. A malformed provider node can specify fewer cells, leaving some of these values uninitialized when the OF DMA core invokes the translation callback.

Reject specifiers that do not contain exactly three cells before reading the argument array.

Fixes fa332de5c6b3 ("dmaengine: ste_dma40: Supply full Device Tree parsing support")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/dma/ste_dma40.c +3 -0
index 32dd63a2c27a..479e69313e4a 100644
@@ -2542,6 +2542,9 @@ static struct dma_chan *d40_xlate(struct of_phandle_args *dma_spec,
 	dma_cap_mask_t cap;
 	u32 flags;
 
+	if (dma_spec->args_count != 3)
+		return NULL;
+
 	memset(&cfg, 0, sizeof(struct stedma40_chan_cfg));
 
 	dma_cap_zero(cap);
Signature · 1 line
2.55.0
author maintainer
#24 lore raw

PATCH v7 18/24 dmaengine: ste_dma40: Reject direction changes after allocation

In reply to Linus Walleij

Logical channel allocation uses the configured direction to select the source or destination allocation mask, derive the logical channel number, and choose the LCPA location.

d40_set_runtime_config_write() nevertheless overwrites the configured direction when a transfer is prepared for the opposite direction. d40_free_dma() then clears the wrong allocation mask, leaking the original resource and potentially releasing one used by another client.

Reject directions that differ from the direction used during allocation and propagate runtime configuration errors to callers. Skip slave runtime configuration for memcpy transfers, which also use d40_prep_sg() but do not require it.

Fixes 95e1400fa131 ("DMAENGINE: add runtime slave config to DMA40 v3")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 29 ++++++++++++++---------------
 1 file changed, 14 insertions(+), 15 deletions(-)
drivers/dma/ste_dma40.c +14 -15
index 479e69313e4a..1b1edcb72480 100644
@@ -2410,7 +2410,13 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 		return NULL;
 	}
 
-	d40_set_runtime_config_write(dchan, &chan->slave_config, direction);
+	if (direction != DMA_MEM_TO_MEM) {
+		ret = d40_set_runtime_config_write(dchan,
+						   &chan->slave_config,
+						   direction);
+		if (ret)
+			return NULL;
+	}
 
 	spin_lock_irqsave(&chan->lock, flags);
 
@@ -2886,6 +2892,13 @@ static int d40_set_runtime_config_write(struct dma_chan *chan,
 		return -EINVAL;
 	}
 
+	if (direction != cfg->dir) {
+		chan_err(d40c,
+			 "transfer direction %d differs from allocated direction %d\n",
+			 direction, cfg->dir);
+		return -EINVAL;
+	}
+
 	src_addr_width = config->src_addr_width;
 	src_maxburst = config->src_maxburst;
 	dst_addr_width = config->dst_addr_width;
@@ -2894,13 +2907,6 @@ static int d40_set_runtime_config_write(struct dma_chan *chan,
 	if (direction == DMA_DEV_TO_MEM) {
 		config_addr = config->src_addr;
 
-		if (cfg->dir != DMA_DEV_TO_MEM)
-			dev_dbg(d40c->base->dev,
-				"channel was not configured for peripheral "
-				"to memory transfer (%d) overriding\n",
-				cfg->dir);
-		cfg->dir = DMA_DEV_TO_MEM;
-
 		/* Configure the memory side */
 		if (dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
 			dst_addr_width = src_addr_width;
@@ -2910,13 +2916,6 @@ static int d40_set_runtime_config_write(struct dma_chan *chan,
 	} else if (direction == DMA_MEM_TO_DEV) {
 		config_addr = config->dst_addr;
 
-		if (cfg->dir != DMA_MEM_TO_DEV)
-			dev_dbg(d40c->base->dev,
-				"channel was not configured for memory "
-				"to peripheral transfer (%d) overriding\n",
-				cfg->dir);
-		cfg->dir = DMA_MEM_TO_DEV;
-
 		/* Configure the memory side */
 		if (src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
 			src_addr_width = dst_addr_width;
Signature · 1 line
2.55.0
author maintainer
#25 lore raw

PATCH v7 19/24 dmaengine: ste_dma40: Fix logical channel bounds check

In reply to Linus Walleij

d40_validate_conf() checks the raw dev_type against num_log_chans, but d40_allocate_channel() derives the lookup_log_chans index as either 2 * dev_type or 2 * dev_type + 1.

Validate the dev_type against the derived logical channel index limit so channel allocation cannot write past lookup_log_chans.

Fixes 26955c07dcf3 ("dmaengine: ste_dma40: Amalgamate DMA source and destination channel numbers")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)
drivers/dma/ste_dma40.c +14 -3
index 1b1edcb72480..fcb074928675 100644
@@ -1881,15 +1881,26 @@ static int d40_validate_conf(struct d40_chan *d40c,
 {
 	int res = 0;
 	bool is_log = conf->mode == STEDMA40_MODE_LOGICAL;
+	bool invalid_dev_type = conf->dev_type < 0;
 
 	if (!conf->dir) {
 		chan_err(d40c, "Invalid direction.\n");
 		res = -EINVAL;
 	}
 
-	if ((is_log && conf->dev_type > d40c->base->num_log_chans)  ||
-	    (!is_log && conf->dev_type > d40c->base->num_phy_chans) ||
-	    (conf->dev_type < 0)) {
+	if (!invalid_dev_type && is_log) {
+		int max_dev_type;
+
+		if (conf->dir == DMA_DEV_TO_MEM)
+			max_dev_type = DIV_ROUND_UP(d40c->base->num_log_chans, 2);
+		else
+			max_dev_type = d40c->base->num_log_chans / 2;
+
+		invalid_dev_type = conf->dev_type >= max_dev_type;
+	}
+
+	if (invalid_dev_type ||
+	    (!is_log && conf->dev_type > d40c->base->num_phy_chans)) {
 		chan_err(d40c, "Invalid device type (%d)\n", conf->dev_type);
 		res = -EINVAL;
 	}
Signature · 1 line
2.55.0
Reviewed-by on v7 19/24
#26 lore raw

Re: [PATCH v7 19/24] dmaengine: ste_dma40: Fix logical channel bounds check

Quoted 7 lines · Linus Walleij

d40_validate_conf() checks the raw dev_type against num_log_chans, but d40_allocate_channel() derives the lookup_log_chans index as either 2 * dev_type or 2 * dev_type + 1.

Validate the dev_type against the derived logical channel index limit so channel allocation cannot write past lookup_log_chans.

Quoted 6 lines
Fixes 26955c07dcf3 ("dmaengine: ste_dma40: Amalgamate DMA source and destination channel numbers")
Reported-by [email protected]
Assisted-by LLM

---

Quoted 41 lines
 drivers/dma/ste_dma40.c | 17 ++++++++++++++---
 1 file changed, 14 insertions(+), 3 deletions(-)
drivers/dma/ste_dma40.c +14 -4
index 1b1edcb72480..fcb074928675 100644
@@ -1881,15 +1881,26 @@ static int d40_validate_conf(struct d40_chan *d40c,
 {
 	int res = 0;
 	bool is_log = conf->mode == STEDMA40_MODE_LOGICAL;
+	bool invalid_dev_type = conf->dev_type < 0;
 
 	if (!conf->dir) {
 		chan_err(d40c, "Invalid direction.\n");
 		res = -EINVAL;
 	}
 
-	if ((is_log && conf->dev_type > d40c->base->num_log_chans)  ||
-	    (!is_log && conf->dev_type > d40c->base->num_phy_chans) ||
-	    (conf->dev_type < 0)) {
+	if (!invalid_dev_type && is_log) {
+		int max_dev_type;
+
+		if (conf->dir == DMA_DEV_TO_MEM)
+			max_dev_type = DIV_ROUND_UP(d40c->base->num_log_chans, 2);
+		else
+			max_dev_type = d40c->base->num_log_chans / 2;
+
+		invalid_dev_type = conf->dev_type >= max_dev_type;
+	}
+
+	if (invalid_dev_type ||
+	    (!is_log && conf->dev_type > d40c->base->num_phy_chans)) {
 		chan_err(d40c, "Invalid device type (%d)\n", conf->dev_type);
 		res = -EINVAL;
 	}
 
--

2.55.0

author maintainer
#27 lore raw

PATCH v7 20/24 dmaengine: ste_dma40: Fix event group bounds

In reply to Linus Walleij

The dev_type validation can allow values whose derived event group has no matching physical channel pair. d40_allocate_channel() then indexes phy_res with j + event_group * 2, and __d40_set_prio_rt() uses the same group to select priority and realtime registers.

The physical-mode validation also compares dev_type with the number of physical channels. However, dev_type identifies an event line: DB8500 has eight physical channels but 64 source and 64 destination event lines. The event group determines which physical channel pair can serve an event, so the physical channel count is not a valid dev_type limit.

Reject dev_type values outside the hardware event-group range, remove the incorrect physical channel count limit, and stop the physical-channel search before a partial final channel group can index past phy_res.

Fixes 26955c07dcf3 ("dmaengine: ste_dma40: Amalgamate DMA source and destination channel numbers")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/dma/ste_dma40.c +22 -4
index fcb074928675..91dc143f9a80 100644
@@ -82,6 +82,10 @@ struct stedma40_platform_data {
 #define D40_LCLA_LINK_PER_EVENT_GRP 128
 #define D40_LCLA_END D40_LCLA_LINK_PER_EVENT_GRP
 
+/* Number of event groups per hardware register layout */
+#define D40_EVENT_GROUPS_V4A 4
+#define D40_EVENT_GROUPS_V4B 5
+
 /* Max number of logical channels per physical channel */
 #define D40_MAX_LOG_CHAN_PER_PHY 32
 
@@ -522,6 +526,7 @@ struct d40_chan {
  * @high_prio_clear: the high priority clear register
  * @interrupt_en: the interrupt enable register
  * @interrupt_clear: the interrupt clear register
+ * @num_event_groups: number of supported event groups
  * @il: the pointer to struct d40_interrupt_lookup
  * @il_size: the size of d40_interrupt_lookup array
  * @init_reg: the pointer to the struct d40_reg_val
@@ -536,6 +541,7 @@ struct d40_gen_dmac {
 	u32				 high_prio_clear;
 	u32				 interrupt_en;
 	u32				 interrupt_clear;
+	u32				 num_event_groups;
 	struct d40_interrupt_lookup	*il;
 	u32				 il_size;
 	struct d40_reg_val		*init_reg;
@@ -1883,6 +1889,11 @@ static int d40_validate_conf(struct d40_chan *d40c,
 	bool is_log = conf->mode == STEDMA40_MODE_LOGICAL;
 	bool invalid_dev_type = conf->dev_type < 0;
 
+	if (!invalid_dev_type &&
+	    D40_TYPE_TO_GROUP(conf->dev_type) >=
+	    d40c->base->gen_dmac.num_event_groups)
+		invalid_dev_type = true;
+
 	if (!conf->dir) {
 		chan_err(d40c, "Invalid direction.\n");
 		res = -EINVAL;
@@ -1899,8 +1910,7 @@ static int d40_validate_conf(struct d40_chan *d40c,
 		invalid_dev_type = conf->dev_type >= max_dev_type;
 	}
 
-	if (invalid_dev_type ||
-	    (!is_log && conf->dev_type > d40c->base->num_phy_chans)) {
+	if (invalid_dev_type) {
 		chan_err(d40c, "Invalid device type (%d)\n", conf->dev_type);
 		res = -EINVAL;
 	}
@@ -2065,8 +2075,12 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 				}
 			}
 		} else
-			for (j = 0; j < d40c->base->num_phy_chans; j += 8) {
+			for (j = 0; j < d40c->base->num_phy_chans;
+			     j += D40_GROUP_SIZE) {
 				int phy_num = j  + event_group * 2;
+				if (phy_num + 1 >= num_phy_chans)
+					break;
+
 				for (i = phy_num; i < phy_num + 2; i++) {
 					if (d40_alloc_mask_set(&phys[i],
 							       is_src,
@@ -2086,8 +2100,10 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		return -EINVAL;
 
 	/* Find logical channel */
-	for (j = 0; j < d40c->base->num_phy_chans; j += 8) {
+	for (j = 0; j < d40c->base->num_phy_chans; j += D40_GROUP_SIZE) {
 		int phy_num = j + event_group * 2;
+		if (phy_num + 1 >= num_phy_chans)
+			break;
 
 		if (d40c->dma_cfg.use_fixed_channel) {
 			i = d40c->dma_cfg.phy_channel;
@@ -3467,6 +3483,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev,
 	base->log_chans = &base->phy_chans[num_phy_chans];
 
 	if (base->plat_data->num_of_phy_chans == 14) {
+		base->gen_dmac.num_event_groups = D40_EVENT_GROUPS_V4B;
 		base->gen_dmac.backup = d40_backup_regs_v4b;
 		base->gen_dmac.backup_size = BACKUP_REGS_SZ_V4B;
 		base->gen_dmac.interrupt_en = D40_DREG_CPCMIS;
@@ -3480,6 +3497,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev,
 		base->gen_dmac.init_reg = dma_init_reg_v4b;
 		base->gen_dmac.init_reg_size = ARRAY_SIZE(dma_init_reg_v4b);
 	} else {
+		base->gen_dmac.num_event_groups = D40_EVENT_GROUPS_V4A;
 		if (base->rev >= 3) {
 			base->gen_dmac.backup = d40_backup_regs_v4a;
 			base->gen_dmac.backup_size = BACKUP_REGS_SZ_V4A;
Signature · 1 line
2.55.0
Reviewed-by on v7 20/24
#28 lore raw

Re: [PATCH v7 20/24] dmaengine: ste_dma40: Fix event group bounds

Quoted 15 lines · Linus Walleij

The dev_type validation can allow values whose derived event group has no matching physical channel pair. d40_allocate_channel() then indexes phy_res with j + event_group * 2, and __d40_set_prio_rt() uses the same group to select priority and realtime registers.

The physical-mode validation also compares dev_type with the number of physical channels. However, dev_type identifies an event line: DB8500 has eight physical channels but 64 source and 64 destination event lines. The event group determines which physical channel pair can serve an event, so the physical channel count is not a valid dev_type limit.

Reject dev_type values outside the hardware event-group range, remove the incorrect physical channel count limit, and stop the physical-channel search before a partial final channel group can index past phy_res.

Quoted 7 lines
Fixes 26955c07dcf3 ("dmaengine: ste_dma40: Amalgamate DMA source and destination channel numbers")
Reported-by [email protected]
Assisted-by LLM

---

Quoted 102 lines
 drivers/dma/ste_dma40.c | 26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/dma/ste_dma40.c +22 -5
index fcb074928675..91dc143f9a80 100644
@@ -82,6 +82,10 @@ struct stedma40_platform_data {
 #define D40_LCLA_LINK_PER_EVENT_GRP 128
 #define D40_LCLA_END D40_LCLA_LINK_PER_EVENT_GRP
 
+/* Number of event groups per hardware register layout */
+#define D40_EVENT_GROUPS_V4A 4
+#define D40_EVENT_GROUPS_V4B 5
+
 /* Max number of logical channels per physical channel */
 #define D40_MAX_LOG_CHAN_PER_PHY 32
 
@@ -522,6 +526,7 @@ struct d40_chan {
  * @high_prio_clear: the high priority clear register
  * @interrupt_en: the interrupt enable register
  * @interrupt_clear: the interrupt clear register
+ * @num_event_groups: number of supported event groups
  * @il: the pointer to struct d40_interrupt_lookup
  * @il_size: the size of d40_interrupt_lookup array
  * @init_reg: the pointer to the struct d40_reg_val
@@ -536,6 +541,7 @@ struct d40_gen_dmac {
 	u32				 high_prio_clear;
 	u32				 interrupt_en;
 	u32				 interrupt_clear;
+	u32				 num_event_groups;
 	struct d40_interrupt_lookup	*il;
 	u32				 il_size;
 	struct d40_reg_val		*init_reg;
@@ -1883,6 +1889,11 @@ static int d40_validate_conf(struct d40_chan *d40c,
 	bool is_log = conf->mode == STEDMA40_MODE_LOGICAL;
 	bool invalid_dev_type = conf->dev_type < 0;
 
+	if (!invalid_dev_type &&
+	    D40_TYPE_TO_GROUP(conf->dev_type) >=
+	    d40c->base->gen_dmac.num_event_groups)
+		invalid_dev_type = true;
+
 	if (!conf->dir) {
 		chan_err(d40c, "Invalid direction.\n");
 		res = -EINVAL;
@@ -1899,8 +1910,7 @@ static int d40_validate_conf(struct d40_chan *d40c,
 		invalid_dev_type = conf->dev_type >= max_dev_type;
 	}
 
-	if (invalid_dev_type ||
-	    (!is_log && conf->dev_type > d40c->base->num_phy_chans)) {
+	if (invalid_dev_type) {
 		chan_err(d40c, "Invalid device type (%d)\n", conf->dev_type);
 		res = -EINVAL;
 	}
@@ -2065,8 +2075,12 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 				}
 			}
 		} else
-			for (j = 0; j < d40c->base->num_phy_chans; j += 8) {
+			for (j = 0; j < d40c->base->num_phy_chans;
+			     j += D40_GROUP_SIZE) {
 				int phy_num = j  + event_group * 2;
+				if (phy_num + 1 >= num_phy_chans)
+					break;
+
 				for (i = phy_num; i < phy_num + 2; i++) {
 					if (d40_alloc_mask_set(&phys[i],
 							       is_src,
@@ -2086,8 +2100,10 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		return -EINVAL;
 
 	/* Find logical channel */
-	for (j = 0; j < d40c->base->num_phy_chans; j += 8) {
+	for (j = 0; j < d40c->base->num_phy_chans; j += D40_GROUP_SIZE) {
 		int phy_num = j + event_group * 2;
+		if (phy_num + 1 >= num_phy_chans)
+			break;
 
 		if (d40c->dma_cfg.use_fixed_channel) {
 			i = d40c->dma_cfg.phy_channel;
@@ -3467,6 +3483,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev,
 	base->log_chans = &base->phy_chans[num_phy_chans];
 
 	if (base->plat_data->num_of_phy_chans == 14) {
+		base->gen_dmac.num_event_groups = D40_EVENT_GROUPS_V4B;
 		base->gen_dmac.backup = d40_backup_regs_v4b;
 		base->gen_dmac.backup_size = BACKUP_REGS_SZ_V4B;
 		base->gen_dmac.interrupt_en = D40_DREG_CPCMIS;
@@ -3480,6 +3497,7 @@ static int __init d40_hw_detect_init(struct platform_device *pdev,
 		base->gen_dmac.init_reg = dma_init_reg_v4b;
 		base->gen_dmac.init_reg_size = ARRAY_SIZE(dma_init_reg_v4b);
 	} else {
+		base->gen_dmac.num_event_groups = D40_EVENT_GROUPS_V4A;
 		if (base->rev >= 3) {
 			base->gen_dmac.backup = d40_backup_regs_v4a;
 			base->gen_dmac.backup_size = BACKUP_REGS_SZ_V4A;
 
--

2.55.0

author maintainer
#29 lore raw

PATCH v7 21/24 dmaengine: ste_dma40: Fix V4B event group mapping

In reply to Linus Walleij

DMA40 physical resources are connected in pairs to event groups. The mapping repeats after each complete set of groups.

D40_GROUP_SIZE and D40_PHYS_TO_GROUP() encode the four-group V4A layout. On V4B, which has five groups, resources 8 and 9 are consequently offered both to event groups 0 and 4. The GCC clock bookkeeping also treats these resources as group 0 instead of group 4.

Derive the physical-resource stride and reverse mapping from the variant-specific number of event groups. This preserves the V4A mapping and gives V4B a ten-resource stride: resources 8 and 9 belong only to group 4, while resources 10 and 11 repeat group 0.

Fixes 3cb645dc85a0 ("dmaengine: ste_dma40: support more than 128 event lines")
Assisted-by LLM
---
 drivers/dma/ste_dma40.c    | 47 ++++++++++++++++++++++++++++++++--------------
 drivers/dma/ste_dma40_ll.h |  2 --
 2 files changed, 33 insertions(+), 16 deletions(-)
drivers/dma/ste_dma40.c +33 -14
index 91dc143f9a80..a5471a9157cd 100644
@@ -85,6 +85,7 @@ struct stedma40_platform_data {
 /* Number of event groups per hardware register layout */
 #define D40_EVENT_GROUPS_V4A 4
 #define D40_EVENT_GROUPS_V4B 5
+#define D40_PHYS_PER_EVENT_GROUP 2
 
 /* Max number of logical channels per physical channel */
 #define D40_MAX_LOG_CHAN_PER_PHY 32
@@ -2027,6 +2028,12 @@ static bool d40_alloc_mask_free(struct d40_phy_res *phy, bool is_src,
 	return is_free;
 }
 
+static int d40_phy_to_group(struct d40_base *base, int phy)
+{
+	return (phy / D40_PHYS_PER_EVENT_GROUP) %
+	       base->gen_dmac.num_event_groups;
+}
+
 static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 {
 	int dev_type = d40c->dma_cfg.dev_type;
@@ -2037,11 +2044,14 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 	int j;
 	int log_num;
 	int num_phy_chans;
+	int phy_group_stride;
 	bool is_src;
 	bool is_log = d40c->dma_cfg.mode == STEDMA40_MODE_LOGICAL;
 
 	phys = d40c->base->phy_res;
 	num_phy_chans = d40c->base->num_phy_chans;
+	phy_group_stride = D40_PHYS_PER_EVENT_GROUP *
+			   d40c->base->gen_dmac.num_event_groups;
 
 	if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM) {
 		log_num = 2 * dev_type;
@@ -2075,13 +2085,18 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 				}
 			}
 		} else
-			for (j = 0; j < d40c->base->num_phy_chans;
-			     j += D40_GROUP_SIZE) {
-				int phy_num = j  + event_group * 2;
-				if (phy_num + 1 >= num_phy_chans)
+			for (j = 0; j < num_phy_chans;
+			     j += phy_group_stride) {
+				int phy_num = j + event_group *
+					      D40_PHYS_PER_EVENT_GROUP;
+
+				if (phy_num + D40_PHYS_PER_EVENT_GROUP >
+				    num_phy_chans)
 					break;
 
-				for (i = phy_num; i < phy_num + 2; i++) {
+				for (i = phy_num;
+				     i < phy_num + D40_PHYS_PER_EVENT_GROUP;
+				     i++) {
 					if (d40_alloc_mask_set(&phys[i],
 							       is_src,
 							       0,
@@ -2100,9 +2115,10 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		return -EINVAL;
 
 	/* Find logical channel */
-	for (j = 0; j < d40c->base->num_phy_chans; j += D40_GROUP_SIZE) {
-		int phy_num = j + event_group * 2;
-		if (phy_num + 1 >= num_phy_chans)
+	for (j = 0; j < num_phy_chans; j += phy_group_stride) {
+		int phy_num = j + event_group * D40_PHYS_PER_EVENT_GROUP;
+
+		if (phy_num + D40_PHYS_PER_EVENT_GROUP > num_phy_chans)
 			break;
 
 		if (d40c->dma_cfg.use_fixed_channel) {
@@ -2129,14 +2145,17 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		 * channels.
 		 */
 		if (is_src) {
-			for (i = phy_num; i < phy_num + 2; i++) {
+			for (i = phy_num;
+			     i < phy_num + D40_PHYS_PER_EVENT_GROUP;
+			     i++) {
 				if (d40_alloc_mask_set(&phys[i], is_src,
 						       event_line, is_log,
 						       first_phy_user))
 					goto found_log;
 			}
 		} else {
-			for (i = phy_num + 1; i >= phy_num; i--) {
+			for (i = phy_num + D40_PHYS_PER_EVENT_GROUP - 1;
+			     i >= phy_num; i--) {
 				if (d40_alloc_mask_set(&phys[i], is_src,
 						       event_line, is_log,
 						       first_phy_user))
@@ -3307,9 +3326,9 @@ static int __init d40_phy_res_init(struct d40_base *base)
 			base->phy_res[i].allocated_src = D40_ALLOC_PHY;
 			base->phy_res[i].allocated_dst = D40_ALLOC_PHY;
 			base->phy_res[i].reserved = true;
-			gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(i),
+			gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, i),
 						       D40_DREG_GCC_SRC);
-			gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(i),
+			gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, i),
 						       D40_DREG_GCC_DST);
 
 
@@ -3329,9 +3348,9 @@ static int __init d40_phy_res_init(struct d40_base *base)
 		base->phy_res[chan].allocated_src = D40_ALLOC_PHY;
 		base->phy_res[chan].allocated_dst = D40_ALLOC_PHY;
 		base->phy_res[chan].reserved = true;
-		gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(chan),
+		gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, chan),
 					       D40_DREG_GCC_SRC);
-		gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(chan),
+		gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, chan),
 					       D40_DREG_GCC_DST);
 		num_phy_chans_avail--;
 	}
drivers/dma/ste_dma40_ll.h +0 -2
index 2e30e9a94a1e..55090cb31057 100644
@@ -16,8 +16,6 @@
 
 #define D40_TYPE_TO_GROUP(type) (type / 16)
 #define D40_TYPE_TO_EVENT(type) (type % 16)
-#define D40_GROUP_SIZE 8
-#define D40_PHYS_TO_GROUP(phys) ((phys & (D40_GROUP_SIZE - 1)) / 2)
 
 /* Most bits of the CFG register are the same in log as in phy mode */
 #define D40_SREG_CFG_MST_POS		15
Signature · 1 line
2.55.0
Reviewed-by on v7 21/24
#30 lore raw

Re: [PATCH v7 21/24] dmaengine: ste_dma40: Fix V4B event group mapping

Quoted 13 lines · Linus Walleij

DMA40 physical resources are connected in pairs to event groups. The mapping repeats after each complete set of groups.

D40_GROUP_SIZE and D40_PHYS_TO_GROUP() encode the four-group V4A layout. On V4B, which has five groups, resources 8 and 9 are consequently offered both to event groups 0 and 4. The GCC clock bookkeeping also treats these resources as group 0 instead of group 4.

Derive the physical-resource stride and reverse mapping from the variant-specific number of event groups. This preserves the V4A mapping and gives V4B a ten-resource stride: resources 8 and 9 belong only to group 4, while resources 10 and 11 repeat group 0.

Quoted 4 lines
Fixes 3cb645dc85a0 ("dmaengine: ste_dma40: support more than 128 event lines")
Assisted-by LLM

---

Quoted 143 lines
 drivers/dma/ste_dma40.c    | 47 ++++++++++++++++++++++++++++++++--------------
 drivers/dma/ste_dma40_ll.h |  2 --
 2 files changed, 33 insertions(+), 16 deletions(-)
drivers/dma/ste_dma40.c +33 -14
index 91dc143f9a80..a5471a9157cd 100644
@@ -85,6 +85,7 @@ struct stedma40_platform_data {
 /* Number of event groups per hardware register layout */
 #define D40_EVENT_GROUPS_V4A 4
 #define D40_EVENT_GROUPS_V4B 5
+#define D40_PHYS_PER_EVENT_GROUP 2
 
 /* Max number of logical channels per physical channel */
 #define D40_MAX_LOG_CHAN_PER_PHY 32
@@ -2027,6 +2028,12 @@ static bool d40_alloc_mask_free(struct d40_phy_res *phy, bool is_src,
 	return is_free;
 }
 
+static int d40_phy_to_group(struct d40_base *base, int phy)
+{
+	return (phy / D40_PHYS_PER_EVENT_GROUP) %
+	       base->gen_dmac.num_event_groups;
+}
+
 static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 {
 	int dev_type = d40c->dma_cfg.dev_type;
@@ -2037,11 +2044,14 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 	int j;
 	int log_num;
 	int num_phy_chans;
+	int phy_group_stride;
 	bool is_src;
 	bool is_log = d40c->dma_cfg.mode == STEDMA40_MODE_LOGICAL;
 
 	phys = d40c->base->phy_res;
 	num_phy_chans = d40c->base->num_phy_chans;
+	phy_group_stride = D40_PHYS_PER_EVENT_GROUP *
+			   d40c->base->gen_dmac.num_event_groups;
 
 	if (d40c->dma_cfg.dir == DMA_DEV_TO_MEM) {
 		log_num = 2 * dev_type;
@@ -2075,13 +2085,18 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 				}
 			}
 		} else
-			for (j = 0; j < d40c->base->num_phy_chans;
-			     j += D40_GROUP_SIZE) {
-				int phy_num = j  + event_group * 2;
-				if (phy_num + 1 >= num_phy_chans)
+			for (j = 0; j < num_phy_chans;
+			     j += phy_group_stride) {
+				int phy_num = j + event_group *
+					      D40_PHYS_PER_EVENT_GROUP;
+
+				if (phy_num + D40_PHYS_PER_EVENT_GROUP >
+				    num_phy_chans)
 					break;
 
-				for (i = phy_num; i < phy_num + 2; i++) {
+				for (i = phy_num;
+				     i < phy_num + D40_PHYS_PER_EVENT_GROUP;
+				     i++) {
 					if (d40_alloc_mask_set(&phys[i],
 							       is_src,
 							       0,
@@ -2100,9 +2115,10 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		return -EINVAL;
 
 	/* Find logical channel */
-	for (j = 0; j < d40c->base->num_phy_chans; j += D40_GROUP_SIZE) {
-		int phy_num = j + event_group * 2;
-		if (phy_num + 1 >= num_phy_chans)
+	for (j = 0; j < num_phy_chans; j += phy_group_stride) {
+		int phy_num = j + event_group * D40_PHYS_PER_EVENT_GROUP;
+
+		if (phy_num + D40_PHYS_PER_EVENT_GROUP > num_phy_chans)
 			break;
 
 		if (d40c->dma_cfg.use_fixed_channel) {
@@ -2129,14 +2145,17 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		 * channels.
 		 */
 		if (is_src) {
-			for (i = phy_num; i < phy_num + 2; i++) {
+			for (i = phy_num;
+			     i < phy_num + D40_PHYS_PER_EVENT_GROUP;
+			     i++) {
 				if (d40_alloc_mask_set(&phys[i], is_src,
 						       event_line, is_log,
 						       first_phy_user))
 					goto found_log;
 			}
 		} else {
-			for (i = phy_num + 1; i >= phy_num; i--) {
+			for (i = phy_num + D40_PHYS_PER_EVENT_GROUP - 1;
+			     i >= phy_num; i--) {
 				if (d40_alloc_mask_set(&phys[i], is_src,
 						       event_line, is_log,
 						       first_phy_user))
@@ -3307,9 +3326,9 @@ static int __init d40_phy_res_init(struct d40_base *base)
 			base->phy_res[i].allocated_src = D40_ALLOC_PHY;
 			base->phy_res[i].allocated_dst = D40_ALLOC_PHY;
 			base->phy_res[i].reserved = true;
-			gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(i),
+			gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, i),
 						       D40_DREG_GCC_SRC);
-			gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(i),
+			gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, i),
 						       D40_DREG_GCC_DST);
 
 
@@ -3329,9 +3348,9 @@ static int __init d40_phy_res_init(struct d40_base *base)
 		base->phy_res[chan].allocated_src = D40_ALLOC_PHY;
 		base->phy_res[chan].allocated_dst = D40_ALLOC_PHY;
 		base->phy_res[chan].reserved = true;
-		gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(chan),
+		gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, chan),
 					       D40_DREG_GCC_SRC);
-		gcc |= D40_DREG_GCC_EVTGRP_ENA(D40_PHYS_TO_GROUP(chan),
+		gcc |= D40_DREG_GCC_EVTGRP_ENA(d40_phy_to_group(base, chan),
 					       D40_DREG_GCC_DST);
 		num_phy_chans_avail--;
 	}
drivers/dma/ste_dma40_ll.h +0 -3
index 2e30e9a94a1e..55090cb31057 100644
@@ -16,8 +16,6 @@
 
 #define D40_TYPE_TO_GROUP(type) (type / 16)
 #define D40_TYPE_TO_EVENT(type) (type % 16)
-#define D40_GROUP_SIZE 8
-#define D40_PHYS_TO_GROUP(phys) ((phys & (D40_GROUP_SIZE - 1)) / 2)
 
 /* Most bits of the CFG register are the same in log as in phy mode */
 #define D40_SREG_CFG_MST_POS		15
 
--

2.55.0

author maintainer
#31 lore raw

PATCH v7 22/24 dmaengine: ste_dma40: Search all blocks for fixed logical channels

In reply to Linus Walleij

Fixed logical channel allocation scans physical channels in blocks of eight. When the requested physical channel does not belong to the first block, d40_allocate_channel() returns -EINVAL instead of checking later blocks.

Skip nonmatching blocks so controllers with more than eight physical channels can allocate fixed logical channels from the later blocks.

Fixes 5cd326fd27da ("dmaengine/ste_dma40: allow fixed physical channel")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +2 -5
index a5471a9157cd..fe9539138549 100644
@@ -2124,11 +2124,8 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		if (d40c->dma_cfg.use_fixed_channel) {
 			i = d40c->dma_cfg.phy_channel;
 
-			if ((i != phy_num) && (i != phy_num + 1)) {
-				dev_err(chan2dev(d40c),
-					"invalid fixed phy channel %d\n", i);
-				return -EINVAL;
-			}
+			if (i != phy_num && i != phy_num + 1)
+				continue;
 
 			if (d40_alloc_mask_set(&phys[i], is_src, event_line,
 					       is_log, first_phy_user))
Signature · 1 line
2.55.0
maintainer
#32 lore raw

Re: [PATCH v7 22/24] dmaengine: ste_dma40: Search all blocks for fixed logical channels

Quoted 7 lines · Linus Walleij

Fixed logical channel allocation scans physical channels in blocks of eight. When the requested physical channel does not belong to the first block, d40_allocate_channel() returns -EINVAL instead of checking later blocks.

Skip nonmatching blocks so controllers with more than eight physical channels can allocate fixed logical channels from the later blocks.

This failed to apply for me, I have skipped and applied the rest

Quoted 32 lines
Fixes 5cd326fd27da ("dmaengine/ste_dma40: allow fixed physical channel")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/dma/ste_dma40.c +2 -5
index a5471a9157cd..fe9539138549 100644
@@ -2124,11 +2124,8 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 		if (d40c->dma_cfg.use_fixed_channel) {
 			i = d40c->dma_cfg.phy_channel;
 
-			if ((i != phy_num) && (i != phy_num + 1)) {
-				dev_err(chan2dev(d40c),
-					"invalid fixed phy channel %d\n", i);
-				return -EINVAL;
-			}
+			if (i != phy_num && i != phy_num + 1)
+				continue;
 
 			if (d40_alloc_mask_set(&phys[i], is_src, event_line,
 					       is_log, first_phy_user))
Signature · 2 lines
-- 
2.55.0
Signature · 1 line
~Vinod
author maintainer
#33 lore raw

Re: [PATCH v7 22/24] dmaengine: ste_dma40: Search all blocks for fixed logical channels

Hi Vinod,

Quoted 10 lines · Vinod Koul
Quoted 7 lines · Linus Walleij

Fixed logical channel allocation scans physical channels in blocks of eight. When the requested physical channel does not belong to the first block, d40_allocate_channel() returns -EINVAL instead of checking later blocks.

Skip nonmatching blocks so controllers with more than eight physical channels can allocate fixed logical channels from the later blocks.

This failed to apply for me, I have skipped and applied the rest

Thanks Vinod, I'll rebase it on your tree and send it separately.

Yours,
Linus Walleij

author maintainer
#34 lore raw

PATCH v7 23/24 dmaengine: ste_dma40: Validate fixed physical channel indexes

In reply to Linus Walleij

Fixed physical memcpy allocation uses dma_cfg.phy_channel directly as an index into phy_res when use_fixed_channel is set. d40_validate_conf() validates dev_type but not the fixed physical channel, allowing an invalid configuration to access memory outside the array.

Validate the fixed physical channel centrally before accepting the channel configuration.

Fixes f000df8c5a0e ("dmaengine: ste_dma40: support fixed physical channel allocation")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/dma/ste_dma40.c +8 -0
index fe9539138549..4bf969511439 100644
@@ -1916,6 +1916,14 @@ static int d40_validate_conf(struct d40_chan *d40c,
 		res = -EINVAL;
 	}
 
+	if (conf->use_fixed_channel &&
+	    (conf->phy_channel < 0 ||
+	     conf->phy_channel >= d40c->base->num_phy_chans)) {
+		chan_err(d40c, "Invalid physical channel (%d)\n",
+			 conf->phy_channel);
+		res = -EINVAL;
+	}
+
 	if (conf->dir == DMA_DEV_TO_DEV) {
 		/*
 		 * DMAC HW supports it. Will be added to this driver,
Signature · 1 line
2.55.0
author maintainer
#35 lore raw

PATCH v7 24/24 dmaengine: ste_dma40: Validate memcpy configuration

In reply to Linus Walleij

d40_config_memcpy() builds a default memcpy configuration without passing it through d40_validate_conf(). A dev_type supplied through the memcpy-channels device tree property can therefore bypass the bounds checks added for client configurations.

The generic DMA direction enum assigns zero to DMA_MEM_TO_MEM, unlike DMA40's old private enum. Allow memory-to-memory directions in the validator so checking the generated configuration does not reject all memcpy channels.

Validate the generated memcpy configuration before deriving logical channel registers or allocating the channel.

Fixes 2c2b62d5d911 ("dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones")
Reported-by [email protected]
Assisted-by LLM
---
 drivers/dma/ste_dma40.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
drivers/dma/ste_dma40.c +11 -1
index 4bf969511439..71942d0b0516 100644
@@ -1895,7 +1895,8 @@ static int d40_validate_conf(struct d40_chan *d40c,
 	    d40c->base->gen_dmac.num_event_groups)
 		invalid_dev_type = true;
 
-	if (!conf->dir) {
+	if (conf->dir != DMA_MEM_TO_MEM &&
+	    !is_slave_direction(conf->dir)) {
 		chan_err(d40c, "Invalid direction.\n");
 		res = -EINVAL;
 	}
@@ -2187,12 +2188,17 @@ static int d40_allocate_channel(struct d40_chan *d40c, bool *first_phy_user)
 static int d40_config_memcpy(struct d40_chan *d40c)
 {
 	dma_cap_mask_t cap = d40c->chan.device->cap_mask;
+	int ret;
 
 	if (dma_has_cap(DMA_MEMCPY, cap) && !dma_has_cap(DMA_SLAVE, cap)) {
 		d40c->dma_cfg = dma40_memcpy_conf_log;
 		d40c->dma_cfg.dev_type =
 			d40c->base->plat_data->memcpy_channels[d40c->chan.chan_id];
 
+		ret = d40_validate_conf(d40c, &d40c->dma_cfg);
+		if (ret)
+			return ret;
+
 		d40_log_cfg(&d40c->dma_cfg,
 			    &d40c->log_def.lcsp1, &d40c->log_def.lcsp3);
 
@@ -2200,6 +2206,10 @@ static int d40_config_memcpy(struct d40_chan *d40c)
 		   dma_has_cap(DMA_SLAVE, cap)) {
 		d40c->dma_cfg = dma40_memcpy_conf_phy;
 
+		ret = d40_validate_conf(d40c, &d40c->dma_cfg);
+		if (ret)
+			return ret;
+
 		/* Generate interrupt at end of transfer or relink. */
 		d40c->dst_def_cfg |= BIT(D40_SREG_CFG_TIM_POS);
 
Signature · 1 line
2.55.0
maintainer Applied
#36 lore raw
In reply to Linus Walleij
Quoted 8 lines · Linus Walleij

This series fixes many DMA40 bugs.

Roughly half were found while reviewing the Ux500 LCLA SRAM power-domain conversion.

The cyclic transfer residue bug was exposed by Ux500 audio playback.

[...]

Applied, thanks!

[01/24] dmaengine: ste_dma40: Fix physical cyclic capability

        commit: 11101a8e3e42273a5910a149f6324040b88f4747
[02/24] dmaengine: ste_dma40: Fix cyclic transfer residue
        commit: c80edceff29ee212987c2d2c851b2cb2eb4b477a
[03/24] dmaengine: ste_dma40: Recover coalesced cyclic callbacks
        commit: db28400d92cd97005065dad230b8a5d72ab121cb
[04/24] dmaengine: ste_dma40: Fix failed start cleanup
        commit: 8175ead5727173d4b96d1e830e696765d75ade71
[05/24] dmaengine: ste_dma40: Fix probe runtime PM disable
        commit: c6809b381e34f8966cc3d9e5d7d658775a408f83
[06/24] dmaengine: ste_dma40: Check runtime PM in IRQ
        commit: 12787e3f2f93f3af59769b08ee4fcb044531120b
[07/24] dmaengine: ste_dma40: Handle runtime PM resume errors
        commit: 55a35231b8ced2250a7743ec350a9566d553780e
[08/24] dmaengine: ste_dma40: Return IRQ_NONE when no interrupt is pending
        commit: b96967644c524d34b2fdd2e58c31e7b36e3469e6
[09/24] dmaengine: ste_dma40: Init hardware before registration
        commit: ffd583a734dc4bdafb9e18d9aa48b6efafd1a628
[10/24] dmaengine: ste_dma40: Fix probe IRQ leak
        commit: 7ca608cf6b842685bbbe131d4f7d638f7cdc2b5d
[11/24] dmaengine: ste_dma40: Fix DMA registration unwind
        commit: f71ef686f913c8e9771a54466a76d653b83cd3dd
[12/24] dmaengine: ste_dma40: Fix LCLA allocation order
        commit: 7d4dc355c574d414d2402ac481a2fc4ee51e2771
[13/24] dmaengine: ste_dma40: Fix probe LCLA free
        commit: 750dfcdb7a406bdd52d604099a631bbe96ddda91
[14/24] dmaengine: ste_dma40: Put the LCPA SRAM node
        commit: 9a3762b470421658214baeb6cce3eed7344bb435
[15/24] dmaengine: ste_dma40: Fix memcpy channel parsing
        commit: f2baf04a695de4f952513cb00ccf0338c6db2e00
[16/24] dmaengine: ste_dma40: Validate disabled channel indexes
        commit: c96e9f056095825b5f8d4a11f4107fc174892f92
[17/24] dmaengine: ste_dma40: Validate DMA specifier length
        commit: 9f1064ebe17cf3ab65ac6eb166398e02678aea33
[18/24] dmaengine: ste_dma40: Reject direction changes after allocation
        commit: 77ebc64f40717b8501793b5f5ee717a141e62e8e
[19/24] dmaengine: ste_dma40: Fix logical channel bounds check
        commit: 57938e0c2a24f9f792fe9f611391ef6b58d1aa21
[20/24] dmaengine: ste_dma40: Fix event group bounds
        commit: e66a9dbe04c71249cfb2a544c9c25d1b3b761fba
[21/24] dmaengine: ste_dma40: Fix V4B event group mapping
        commit: b36f8fce7314fed53563c60e683ff86deb8a51ae
[22/24] dmaengine: ste_dma40: Search all blocks for fixed logical channels
        (no commit info)
[23/24] dmaengine: ste_dma40: Validate fixed physical channel indexes
        commit: 884e01160bc727509b4fdf04e763a86b936df464
[24/24] dmaengine: ste_dma40: Validate memcpy configuration
        commit: 0ac4a90c4805b41013044fdefff051ae59a54302

Best regards,

Signature · 1 line
~Vinod