Skip to contentSkip to conversation

arm64: dts: qcom: monaco: Add EL2 overlay for monaco-arduino-monza

PATCH Applied Pablo del Arco 4 participants 4 messages Oct 4 – Nov 8

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: qcom: monaco: Add EL2 overlay for monaco-arduino-monza

Build an EL2 combined DTB for the Arduino VENTUNO Q (monaco-arduino-monza) from the base DTB and monaco-el2.dtbo, as monaco-evk-el2.dtb already does for the Monaco EVK.

The board boots under Gunyah by default. This DTB lets it run Linux at EL2 with KVM when the boot firmware is set up for that.

---
Build tested with CHECK_DTBS=y on top of qcom for-next. Not boot tested at EL2, the board ships boot firmware set up for Gunyah.

 arch/arm64/boot/dts/qcom/Makefile | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/Makefile +4 -0
index 88230c4e0..859586cdc 100644
@@ -68,6 +68,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= mahua-lenovo-thinkpad-t14s-gen7-lcd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= milos-fairphone-fp6.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= milos-nothing-asteroids.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-arduino-monza.dtb
+
+monaco-arduino-monza-el2-dtbs	:= monaco-arduino-monza.dtb monaco-el2.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM)	+= monaco-arduino-monza-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-ac-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-evk.dtb
 
Signature · 1 line
2.43.0
Reviewed-by on v1 1/1
#1 lore raw
Quoted 8 lines · Pablo del Arco

Build an EL2 combined DTB for the Arduino VENTUNO Q (monaco-arduino-monza) from the base DTB and monaco-el2.dtbo, as monaco-evk-el2.dtb already does for the Monaco EVK.

The board boots under Gunyah by default. This DTB lets it run Linux at EL2 with KVM when the boot firmware is set up for that.

Signature · 1 line
-Mukesh Ojha
Reviewed-by on v1 1/1
#2 lore raw
In reply to Pablo del Arco
Quoted 9 lines · Pablo del Arco

Build an EL2 combined DTB for the Arduino VENTUNO Q (monaco-arduino-monza) from the base DTB and monaco-el2.dtbo, as monaco-evk-el2.dtb already does for the Monaco EVK.

The board boots under Gunyah by default. This DTB lets it run Linux at EL2 with KVM when the boot firmware is set up for that.

---

Konrad

maintainer Applied
#3 lore raw
In reply to Pablo del Arco
Quoted 8 lines · Pablo del Arco

Build an EL2 combined DTB for the Arduino VENTUNO Q (monaco-arduino-monza) from the base DTB and monaco-el2.dtbo, as monaco-evk-el2.dtb already does for the Monaco EVK.

The board boots under Gunyah by default. This DTB lets it run Linux at EL2 with KVM when the boot firmware is set up for that.

[...]

Applied, thanks!

[1/1] arm64: dts: qcom: monaco: Add EL2 overlay for monaco-arduino-monza

      commit: 288c04d58f3cb8178540661d10ef95798170f545

Best regards,

Signature · 1 line
Bjorn Andersson <[email protected]>