Skip to contentSkip to conversation

Support mt7531 on BPI-R2 Pro

PATCH Applied Frank Wunderlich 4 participants 14 messages Jun 10, 2022 – Jun 15, 2022

Subsystems (7)
lore
Share & tools
lore
#0 lore raw

v4 cover Support mt7531 on BPI-R2 Pro

From: Frank Wunderlich <[email protected]>

This Series add Support for the mt7531 switch on Bananapi R2 Pro board.

This board uses port5 of the switch to conect to the gmac0 of the rk3568 SoC.

Currently CPU-Port is hardcoded in the mt7530 driver to port 6.

Compared to v1 the reset-Patch was dropped as it was not needed and CPU-Port-changes are completely rewriten based on suggestions/code from Vladimir Oltean (many thanks to this).
In DTS Patch i only dropped the status-property that was not needed/ignored by driver.

Due to the Changes i also made a regression test on mt7623 bpi-r2 (mt7623 soc + mt7530) and bpi-r64 (mt7622 soc + mt7531) with cpu- port 6. Tests were done directly (ipv4 config on dsa user port) and with vlan-aware bridge including vlan that was tagged outgoing on dsa user port.

v4:
- rebase on 5.19-rc1
- some changes in bindings-document and fix wrong squashing from v3

Frank Wunderlich (6):
dt-bindings: net: dsa: convert binding for mediatek switches
net: dsa: mt7530: rework mt7530_hw_vlan_{add,del}
net: dsa: mt7530: rework mt753[01]_setup
net: dsa: mt7530: get cpu-port via dp->cpu_dp instead of constant
dt-bindings: net: dsa: make reset optional and add rgmii-mode to

    mt7531

arm64: dts: rockchip: Add mt7531 dsa node to BPI-R2-Pro board

 .../bindings/net/dsa/mediatek,mt7530.yaml     | 404 ++++++++++++++++++
 .../devicetree/bindings/net/dsa/mt7530.txt    | 327 --------------
 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   |  48 +++
 drivers/net/dsa/mt7530.c                      |  82 ++--
 drivers/net/dsa/mt7530.h                      |   1 -
 5 files changed, 505 insertions(+), 357 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
 delete mode 100644 Documentation/devicetree/bindings/net/dsa/mt7530.txt
Signature · 1 line
2.34.1
#1 lore raw

PATCH v4 1/6 dt-bindings: net: dsa: convert binding for mediatek switches

From: Frank Wunderlich <[email protected]>

Convert txt binding to yaml binding for Mediatek switches.

---
v4:
- fix squash of port 5 as cpu-port
- drop type from interrupt-controller and add depency for this
- use ethernet-ports in examples
- drop address-/size-cells

v3:
- include standalone patch in mt7530 series
- drop some descriptions (gpio-cells,reset-gpios,reset-names)
- drop | from descriptions
- move patternProperties above allOf

v2:
- rename mediatek.yaml => mediatek,mt7530.yaml
- drop "boolean" in description
- drop description for interrupt-properties
- drop #interrupt-cells as requirement
- example: eth=>ethernet,mdio0=>mdio,comment indention
- replace 0 by GPIO_ACTIVE_HIGH in first example
- use port(s)-pattern from dsa.yaml
- adress/size-cells not added to required because this is defined at mdio-level inc current dts , not switch level

---
 .../bindings/net/dsa/mediatek,mt7530.yaml     | 406 ++++++++++++++++++
 .../devicetree/bindings/net/dsa/mt7530.txt    | 327 --------------
 2 files changed, 406 insertions(+), 327 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
 delete mode 100644 Documentation/devicetree/bindings/net/dsa/mt7530.txt
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml new file +406 -0
new file mode 100644
index 000000000000..112cfaa7e3f6
@@ -0,0 +1,406 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT7530 Ethernet switch
+
+maintainers:
+  - Sean Wang <[email protected]>
+  - Landen Chao <[email protected]>
+  - DENG Qingfang <[email protected]>
+
+description: |
+  Port 5 of mt7530 and mt7621 switch is muxed between:
+  1. GMAC5: GMAC5 can interface with another external MAC or PHY.
+  2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC
+     of the SOC. Used in many setups where port 0/4 becomes the WAN port.
+     Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to
+       GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not
+       connected to external component!
+
+  Port 5 modes/configurations:
+  1. Port 5 is disabled and isolated: An external phy can interface to the 2nd
+     GMAC of the SOC.
+     In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd
+     GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC!
+  2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC.
+     It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode
+     and RGMII delay.
+  3. Port 5 is muxed to GMAC5 and can interface to an external phy.
+     Port 5 becomes an extra switch port.
+     Only works on platform where external phy TX<->RX lines are swapped.
+     Like in the Ubiquiti ER-X-SFP.
+  4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port.
+     Currently a 2nd CPU port is not supported by DSA code.
+
+  Depending on how the external PHY is wired:
+  1. normal: The PHY can only connect to 2nd GMAC but not to the switch
+  2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as
+     a ethernet port. But can't interface to the 2nd GMAC.
+
+    Based on the DT the port 5 mode is configured.
+
+  Driver tries to lookup the phy-handle of the 2nd GMAC of the master device.
+  When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2.
+  phy-mode must be set, see also example 2 below!
+  * mt7621: phy-mode = "rgmii-txid";
+  * mt7623: phy-mode = "rgmii";
+
+  CPU-Ports need a phy-mode property:
+    Allowed values on mt7530 and mt7621:
+      - "rgmii"
+      - "trgmii"
+    On mt7531:
+      - "1000base-x"
+      - "2500base-x"
+      - "sgmii"
+
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt7530
+      - mediatek,mt7531
+      - mediatek,mt7621
+
+  core-supply:
+    description:
+      Phandle to the regulator node necessary for the core power.
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-controller:
+    type: boolean
+    description:
+      if defined, MT7530's LED controller will run on GPIO mode.
+
+  "#interrupt-cells":
+    const: 1
+
+  interrupt-controller: true
+
+  interrupts:
+    maxItems: 1
+
+  io-supply:
+    description:
+      Phandle to the regulator node necessary for the I/O power.
+      See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt
+      for details for the regulator setup on these boards.
+
+  mediatek,mcm:
+    type: boolean
+    description:
+      if defined, indicates that either MT7530 is the part on multi-chip
+      module belong to MT7623A has or the remotely standalone chip as the
+      function MT7623N reference board provided for.
+
+  reset-gpios:
+    maxItems: 1
+
+  reset-names:
+    const: mcm
+
+  resets:
+    description:
+      Phandle pointing to the system reset controller with line index for
+      the ethsys.
+    maxItems: 1
+
+patternProperties:
+  "^(ethernet-)?ports$":
+    type: object
+
+    patternProperties:
+      "^(ethernet-)?port@[0-9]+$":
+        type: object
+        description: Ethernet switch ports
+
+        unevaluatedProperties: false
+
+        properties:
+          reg:
+            description:
+              Port address described must be 6 for CPU port and from 0 to
+              5 for user ports.
+
+        allOf:
+          - $ref: dsa-port.yaml#
+          - if:
+              properties:
+                label:
+                  items:
+                    - const: cpu
+            then:
+              required:
+                - reg
+                - phy-mode
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - $ref: "dsa.yaml#"
+  - if:
+      required:
+        - mediatek,mcm
+    then:
+      required:
+        - resets
+        - reset-names
+    else:
+      required:
+        - reset-gpios
+
+  - dependencies:
+      interrupt-controller: [ interrupts ]
+
+  - if:
+      properties:
+        compatible:
+          items:
+            - const: mediatek,mt7530
+    then:
+      required:
+        - core-supply
+        - io-supply
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        switch@0 {
+            compatible = "mediatek,mt7530";
+            reg = <0>;
+
+            core-supply = <&mt6323_vpa_reg>;
+            io-supply = <&mt6323_vemc3v3_reg>;
+            reset-gpios = <&pio 33 GPIO_ACTIVE_HIGH>;
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                port@0 {
+                    reg = <0>;
+                    label = "lan0";
+                };
+
+                port@1 {
+                    reg = <1>;
+                    label = "lan1";
+                };
+
+                port@2 {
+                    reg = <2>;
+                    label = "lan2";
+                };
+
+                port@3 {
+                    reg = <3>;
+                    label = "lan3";
+                };
+
+                port@4 {
+                    reg = <4>;
+                    label = "wan";
+                };
+
+                port@6 {
+                    reg = <6>;
+                    label = "cpu";
+                    ethernet = <&gmac0>;
+                    phy-mode = "trgmii";
+                    fixed-link {
+                        speed = <1000>;
+                        full-duplex;
+                    };
+                };
+            };
+        };
+    };
+
+  - |
+    //Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4.
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        gmac0: mac@0 {
+            compatible = "mediatek,eth-mac";
+            reg = <0>;
+            phy-mode = "rgmii";
+
+            fixed-link {
+                speed = <1000>;
+                full-duplex;
+                pause;
+            };
+        };
+
+        gmac1: mac@1 {
+            compatible = "mediatek,eth-mac";
+            reg = <1>;
+            phy-mode = "rgmii-txid";
+            phy-handle = <&phy4>;
+        };
+
+        mdio: mdio-bus {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            /* Internal phy */
+            phy4: ethernet-phy@4 {
+                reg = <4>;
+            };
+
+            mt7530: switch@1f {
+                compatible = "mediatek,mt7621";
+                reg = <0x1f>;
+                mediatek,mcm;
+
+                resets = <&rstctrl 2>;
+                reset-names = "mcm";
+
+                ethernet-ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        label = "lan0";
+                    };
+
+                    port@1 {
+                        reg = <1>;
+                        label = "lan1";
+                    };
+
+                    port@2 {
+                        reg = <2>;
+                        label = "lan2";
+                    };
+
+                    port@3 {
+                        reg = <3>;
+                        label = "lan3";
+                    };
+
+                    /* Commented out. Port 4 is handled by 2nd GMAC.
+                    port@4 {
+                        reg = <4>;
+                        label = "lan4";
+                    };
+                    */
+
+                    port@6 {
+                        reg = <6>;
+                        label = "cpu";
+                        ethernet = <&gmac0>;
+                        phy-mode = "rgmii";
+
+                        fixed-link {
+                            speed = <1000>;
+                            full-duplex;
+                            pause;
+                        };
+                    };
+                };
+            };
+        };
+    };
+
+  - |
+    //Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY.
+
+    ethernet {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        gmac_0: mac@0 {
+            compatible = "mediatek,eth-mac";
+            reg = <0>;
+            phy-mode = "rgmii";
+
+            fixed-link {
+                speed = <1000>;
+                full-duplex;
+                pause;
+            };
+        };
+
+        mdio0: mdio-bus {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            /* External phy */
+            ephy5: ethernet-phy@7 {
+                reg = <7>;
+            };
+
+            switch@1f {
+                compatible = "mediatek,mt7621";
+                reg = <0x1f>;
+                mediatek,mcm;
+
+                resets = <&rstctrl 2>;
+                reset-names = "mcm";
+
+                ethernet-ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        label = "lan0";
+                    };
+
+                    port@1 {
+                        reg = <1>;
+                        label = "lan1";
+                    };
+
+                    port@2 {
+                        reg = <2>;
+                        label = "lan2";
+                    };
+
+                    port@3 {
+                        reg = <3>;
+                        label = "lan3";
+                    };
+
+                    port@4 {
+                        reg = <4>;
+                        label = "lan4";
+                    };
+
+                    port@5 {
+                        reg = <5>;
+                        label = "lan5";
+                        phy-mode = "rgmii";
+                        phy-handle = <&ephy5>;
+                    };
+
+                    cpu_port0: port@6 {
+                        reg = <6>;
+                        label = "cpu";
+                        ethernet = <&gmac_0>;
+                        phy-mode = "rgmii";
+
+                        fixed-link {
+                            speed = <1000>;
+                            full-duplex;
+                            pause;
+                        };
+                    };
+                };
+            };
+        };
+    };
Documentation/devicetree/bindings/net/dsa/mt7530.txt deleted +0 -327

327 lines not on this page · raw message

Signature · 1 line
2.34.1
maintainer Reviewed-by on v4 1/6
#2 lore raw

Re: [PATCH v4 1/6] dt-bindings: net: dsa: convert binding for mediatek switches

Quoted 28 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Convert txt binding to yaml binding for Mediatek switches.

---
v4:
- fix squash of port 5 as cpu-port
- drop type from interrupt-controller and add depency for this
- use ethernet-ports in examples
- drop address-/size-cells

v3:
- include standalone patch in mt7530 series
- drop some descriptions (gpio-cells,reset-gpios,reset-names)
- drop | from descriptions
- move patternProperties above allOf

v2:
- rename mediatek.yaml => mediatek,mt7530.yaml
- drop "boolean" in description
- drop description for interrupt-properties
- drop #interrupt-cells as requirement
- example: eth=>ethernet,mdio0=>mdio,comment indention
- replace 0 by GPIO_ACTIVE_HIGH in first example
- use port(s)-pattern from dsa.yaml
- adress/size-cells not added to required because this is defined at mdio-level inc current dts , not switch level

Quoted 7 lines
---
 .../bindings/net/dsa/mediatek,mt7530.yaml     | 406 ++++++++++++++++++
 .../devicetree/bindings/net/dsa/mt7530.txt    | 327 --------------
 2 files changed, 406 insertions(+), 327 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
 delete mode 100644 Documentation/devicetree/bindings/net/dsa/mt7530.txt
#3 lore raw

PATCH v4 2/6 net: dsa: mt7530: rework mt7530_hw_vlan_{add,del}

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Rework vlan_add/vlan_del functions in preparation for dynamic cpu port.

Currently BIT(MT7530_CPU_PORT) is added to new_members, even though mt7530_port_vlan_add() will be called on the CPU port too.

Let DSA core decide when to call port_vlan_add for the CPU port, rather than doing it implicitly.

We can do autonomous forwarding in a certain VLAN, but not add br0 to that VLAN and avoid flooding the CPU with those packets, if software knows it doesn't need to process them.

---
v2: new patch

---
 drivers/net/dsa/mt7530.c | 30 ++++++++++++------------------
 1 file changed, 12 insertions(+), 18 deletions(-)
drivers/net/dsa/mt7530.c +12 -18
index 2b02d823d497..c1922eaba67a 100644
@@ -1527,11 +1527,11 @@ static void
 mt7530_hw_vlan_add(struct mt7530_priv *priv,
 		   struct mt7530_hw_vlan_entry *entry)
 {
+	struct dsa_port *dp = dsa_to_port(priv->ds, entry->port);
 	u8 new_members;
 	u32 val;
 
-	new_members = entry->old_members | BIT(entry->port) |
-		      BIT(MT7530_CPU_PORT);
+	new_members = entry->old_members | BIT(entry->port);
 
 	/* Validate the entry with independent learning, create egress tag per
 	 * VLAN and joining the port as one of the port members.
@@ -1542,22 +1542,20 @@ mt7530_hw_vlan_add(struct mt7530_priv *priv,
 
 	/* Decide whether adding tag or not for those outgoing packets from the
 	 * port inside the VLAN.
-	 */
-	val = entry->untagged ? MT7530_VLAN_EGRESS_UNTAG :
-				MT7530_VLAN_EGRESS_TAG;
-	mt7530_rmw(priv, MT7530_VAWD2,
-		   ETAG_CTRL_P_MASK(entry->port),
-		   ETAG_CTRL_P(entry->port, val));
-
-	/* CPU port is always taken as a tagged port for serving more than one
+	 * CPU port is always taken as a tagged port for serving more than one
 	 * VLANs across and also being applied with egress type stack mode for
 	 * that VLAN tags would be appended after hardware special tag used as
 	 * DSA tag.
 	 */
+	if (dsa_port_is_cpu(dp))
+		val = MT7530_VLAN_EGRESS_STACK;
+	else if (entry->untagged)
+		val = MT7530_VLAN_EGRESS_UNTAG;
+	else
+		val = MT7530_VLAN_EGRESS_TAG;
 	mt7530_rmw(priv, MT7530_VAWD2,
-		   ETAG_CTRL_P_MASK(MT7530_CPU_PORT),
-		   ETAG_CTRL_P(MT7530_CPU_PORT,
-			       MT7530_VLAN_EGRESS_STACK));
+		   ETAG_CTRL_P_MASK(entry->port),
+		   ETAG_CTRL_P(entry->port, val));
 }
 
 static void
@@ -1576,11 +1574,7 @@ mt7530_hw_vlan_del(struct mt7530_priv *priv,
 		return;
 	}
 
-	/* If certain member apart from CPU port is still alive in the VLAN,
-	 * the entry would be kept valid. Otherwise, the entry is got to be
-	 * disabled.
-	 */
-	if (new_members && new_members != BIT(MT7530_CPU_PORT)) {
+	if (new_members) {
 		val = IVL_MAC | VTAG_EN | PORT_MEM(new_members) |
 		      VLAN_VALID;
 		mt7530_write(priv, MT7530_VAWD1, val);
Signature · 1 line
2.34.1
Reviewed-by on v4 2/6
#4 lore raw

Re: [PATCH v4 2/6] net: dsa: mt7530: rework mt7530_hw_vlan_{add,del}

Quoted 10 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Rework vlan_add/vlan_del functions in preparation for dynamic cpu port.

Currently BIT(MT7530_CPU_PORT) is added to new_members, even though mt7530_port_vlan_add() will be called on the CPU port too.

Let DSA core decide when to call port_vlan_add for the CPU port, rather than doing it implicitly.

Quoted 7 lines

We can do autonomous forwarding in a certain VLAN, but not add br0 to that VLAN and avoid flooding the CPU with those packets, if software knows it doesn't need to process them.

Signature · 1 line
Florian
#5 lore raw

PATCH v4 3/6 net: dsa: mt7530: rework mt753[01]_setup

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Enumerate available cpu-ports instead of using hardcoded constant.

---
 drivers/net/dsa/mt7530.c | 25 +++++++++++++++++++++----
 1 file changed, 21 insertions(+), 4 deletions(-)
drivers/net/dsa/mt7530.c +21 -4
index c1922eaba67a..9c14e46692ee 100644
@@ -2092,11 +2092,12 @@ static int
 mt7530_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
+	struct device_node *dn = NULL;
 	struct device_node *phy_node;
 	struct device_node *mac_np;
 	struct mt7530_dummy_poll p;
 	phy_interface_t interface;
-	struct device_node *dn;
+	struct dsa_port *cpu_dp;
 	u32 id, val;
 	int ret, i;
 
@@ -2104,7 +2105,19 @@ mt7530_setup(struct dsa_switch *ds)
 	 * controller also is the container for two GMACs nodes representing
 	 * as two netdev instances.
 	 */
-	dn = dsa_to_port(ds, MT7530_CPU_PORT)->master->dev.of_node->parent;
+	dsa_switch_for_each_cpu_port(cpu_dp, ds) {
+		dn = cpu_dp->master->dev.of_node->parent;
+		/* It doesn't matter which CPU port is found first,
+		 * their masters should share the same parent OF node
+		 */
+		break;
+	}
+
+	if (!dn) {
+		dev_err(ds->dev, "parent OF node of DSA master not found");
+		return -EINVAL;
+	}
+
 	ds->assisted_learning_on_cpu_port = true;
 	ds->mtu_enforcement_ingress = true;
 
@@ -2266,6 +2279,7 @@ mt7531_setup(struct dsa_switch *ds)
 {
 	struct mt7530_priv *priv = ds->priv;
 	struct mt7530_dummy_poll p;
+	struct dsa_port *cpu_dp;
 	u32 val, id;
 	int ret, i;
 
@@ -2338,8 +2352,11 @@ mt7531_setup(struct dsa_switch *ds)
 				 CORE_PLL_GROUP4, val);
 
 	/* BPDU to CPU port */
-	mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
-		   BIT(MT7530_CPU_PORT));
+	dsa_switch_for_each_cpu_port(cpu_dp, ds) {
+		mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
+			   BIT(cpu_dp->index));
+		break;
+	}
 	mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
 		   MT753X_BPDU_CPU_ONLY);
 
Signature · 1 line
2.34.1
Reviewed-by on v4 3/6
#6 lore raw

Re: [PATCH v4 3/6] net: dsa: mt7530: rework mt753[01]_setup

Quoted 7 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Enumerate available cpu-ports instead of using hardcoded constant.

Signature · 1 line
Florian
#7 lore raw

PATCH v4 4/6 net: dsa: mt7530: get cpu-port via dp->cpu_dp instead of constant

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Replace last occurences of hardcoded cpu-port by cpu_dp member of dsa_port struct.

Now the constant can be dropped.

---
 drivers/net/dsa/mt7530.c | 27 ++++++++++++++++++++-------
 drivers/net/dsa/mt7530.h |  1 -
 2 files changed, 20 insertions(+), 8 deletions(-)
drivers/net/dsa/mt7530.c +20 -7
index 9c14e46692ee..835807911be0 100644
@@ -1038,6 +1038,7 @@ static int
 mt7530_port_enable(struct dsa_switch *ds, int port,
 		   struct phy_device *phy)
 {
+	struct dsa_port *dp = dsa_to_port(ds, port);
 	struct mt7530_priv *priv = ds->priv;
 
 	mutex_lock(&priv->reg_mutex);
@@ -1046,7 +1047,11 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
 	 * restore the port matrix if the port is the member of a certain
 	 * bridge.
 	 */
-	priv->ports[port].pm |= PCR_MATRIX(BIT(MT7530_CPU_PORT));
+	if (dsa_port_is_user(dp)) {
+		struct dsa_port *cpu_dp = dp->cpu_dp;
+
+		priv->ports[port].pm |= PCR_MATRIX(BIT(cpu_dp->index));
+	}
 	priv->ports[port].enable = true;
 	mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
 		   priv->ports[port].pm);
@@ -1195,7 +1200,8 @@ mt7530_port_bridge_join(struct dsa_switch *ds, int port,
 			struct netlink_ext_ack *extack)
 {
 	struct dsa_port *dp = dsa_to_port(ds, port), *other_dp;
-	u32 port_bitmap = BIT(MT7530_CPU_PORT);
+	struct dsa_port *cpu_dp = dp->cpu_dp;
+	u32 port_bitmap = BIT(cpu_dp->index);
 	struct mt7530_priv *priv = ds->priv;
 
 	mutex_lock(&priv->reg_mutex);
@@ -1272,9 +1278,12 @@ mt7530_port_set_vlan_unaware(struct dsa_switch *ds, int port)
 	 * the CPU port get out of VLAN filtering mode.
 	 */
 	if (all_user_ports_removed) {
-		mt7530_write(priv, MT7530_PCR_P(MT7530_CPU_PORT),
+		struct dsa_port *dp = dsa_to_port(ds, port);
+		struct dsa_port *cpu_dp = dp->cpu_dp;
+
+		mt7530_write(priv, MT7530_PCR_P(cpu_dp->index),
 			     PCR_MATRIX(dsa_user_ports(priv->ds)));
-		mt7530_write(priv, MT7530_PVC_P(MT7530_CPU_PORT), PORT_SPEC_TAG
+		mt7530_write(priv, MT7530_PVC_P(cpu_dp->index), PORT_SPEC_TAG
 			     | PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
 	}
 }
@@ -1312,6 +1321,7 @@ mt7530_port_bridge_leave(struct dsa_switch *ds, int port,
 			 struct dsa_bridge bridge)
 {
 	struct dsa_port *dp = dsa_to_port(ds, port), *other_dp;
+	struct dsa_port *cpu_dp = dp->cpu_dp;
 	struct mt7530_priv *priv = ds->priv;
 
 	mutex_lock(&priv->reg_mutex);
@@ -1340,8 +1350,8 @@ mt7530_port_bridge_leave(struct dsa_switch *ds, int port,
 	 */
 	if (priv->ports[port].enable)
 		mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
-			   PCR_MATRIX(BIT(MT7530_CPU_PORT)));
-	priv->ports[port].pm = PCR_MATRIX(BIT(MT7530_CPU_PORT));
+			   PCR_MATRIX(BIT(cpu_dp->index)));
+	priv->ports[port].pm = PCR_MATRIX(BIT(cpu_dp->index));
 
 	/* When a port is removed from the bridge, the port would be set up
 	 * back to the default as is at initial boot which is a VLAN-unaware
@@ -1508,6 +1518,9 @@ static int
 mt7530_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
 			   struct netlink_ext_ack *extack)
 {
+	struct dsa_port *dp = dsa_to_port(ds, port);
+	struct dsa_port *cpu_dp = dp->cpu_dp;
+
 	if (vlan_filtering) {
 		/* The port is being kept as VLAN-unaware port when bridge is
 		 * set up with vlan_filtering not being set, Otherwise, the
@@ -1515,7 +1528,7 @@ mt7530_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
 		 * for becoming a VLAN-aware port.
 		 */
 		mt7530_port_set_vlan_aware(ds, port);
-		mt7530_port_set_vlan_aware(ds, MT7530_CPU_PORT);
+		mt7530_port_set_vlan_aware(ds, cpu_dp->index);
 	} else {
 		mt7530_port_set_vlan_unaware(ds, port);
 	}
drivers/net/dsa/mt7530.h +0 -1
index 71e36b69b96d..e509af95c354 100644
@@ -8,7 +8,6 @@
 
 #define MT7530_NUM_PORTS		7
 #define MT7530_NUM_PHYS			5
-#define MT7530_CPU_PORT			6
 #define MT7530_NUM_FDB_RECORDS		2048
 #define MT7530_ALL_MEMBERS		0xff
 
Signature · 1 line
2.34.1
Reviewed-by on v4 4/6
#8 lore raw

Re: [PATCH v4 4/6] net: dsa: mt7530: get cpu-port via dp->cpu_dp instead of constant

Quoted 10 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Replace last occurences of hardcoded cpu-port by cpu_dp member of dsa_port struct.

Now the constant can be dropped.

Signature · 1 line
Florian
#9 lore raw

PATCH v4 5/6 dt-bindings: net: dsa: make reset optional and add rgmii-mode to mt7531

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

A board may have no independent reset-line, so reset cannot be used inside switch driver.

E.g. on Bananapi-R2 Pro switch and gmac are connected to same reset-line.

Resets should be acquired only to 1 device/driver. This prevents reset to be bound to switch-driver if reset is already used for gmac. If reset is only used by switch driver it resets the switch *and* the gmac after the mdio bus comes up resulting in mdio bus goes down. It takes some time until all is up again, switch driver tries to read from mdio, will fail and defer the probe. On next try the reset does the same again.

Make reset optional for such boards.

Allow port 5 as cpu-port and phy-mode rgmii for mt7531.

- MT7530 supports RGMII on port 5 and RGMII/TRGMII on port 6.
- MT7531 supports on port 5 RGMII and SGMII (dual-sgmii) and SGMII on port 6.

---
v4:
- add port 5 as CPU-Port
- change description

---
 .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml      | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +3 -5
index 112cfaa7e3f6..a3bf432960d8 100644
@@ -55,6 +55,7 @@ description: |
     On mt7531:
       - "1000base-x"
       - "2500base-x"
+      - "rgmii"
       - "sgmii"
 
 
@@ -124,8 +125,8 @@ patternProperties:
         properties:
           reg:
             description:
-              Port address described must be 6 for CPU port and from 0 to
-              5 for user ports.
+              Port address described must be 5 or 6 for CPU port and from 0
+              to 5 for user ports.
 
         allOf:
           - $ref: dsa-port.yaml#
@@ -152,9 +153,6 @@ allOf:
       required:
         - resets
         - reset-names
-    else:
-      required:
-        - reset-gpios
 
   - dependencies:
       interrupt-controller: [ interrupts ]
Signature · 1 line
2.34.1
maintainer Reviewed-by on v4 5/6
#10 lore raw

Re: [PATCH v4 5/6] dt-bindings: net: dsa: make reset optional and add rgmii-mode to mt7531

Quoted 22 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

A board may have no independent reset-line, so reset cannot be used inside switch driver.

E.g. on Bananapi-R2 Pro switch and gmac are connected to same reset-line.

Resets should be acquired only to 1 device/driver. This prevents reset to be bound to switch-driver if reset is already used for gmac. If reset is only used by switch driver it resets the switch *and* the gmac after the mdio bus comes up resulting in mdio bus goes down. It takes some time until all is up again, switch driver tries to read from mdio, will fail and defer the probe. On next try the reset does the same again.

Make reset optional for such boards.

Allow port 5 as cpu-port and phy-mode rgmii for mt7531.

- MT7530 supports RGMII on port 5 and RGMII/TRGMII on port 6.
- MT7531 supports on port 5 RGMII and SGMII (dual-sgmii) and SGMII on port 6.

Quoted 9 lines

---
v4:
- add port 5 as CPU-Port
- change description

---
 .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml      | 8 +++-----
 1 file changed, 3 insertions(+), 5 deletions(-)
#11 lore raw

PATCH v4 6/6 arm64: dts: rockchip: Add mt7531 dsa node to BPI-R2-Pro board

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add Device Tree node for mt7531 switch connected to gmac0.

---
v2:
- drop status=disabled

---
 .../boot/dts/rockchip/rk3568-bpi-r2-pro.dts   | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)
arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts +48 -0
index 40cf2236c0b6..7df8cfb1d3b9 100644
@@ -394,6 +394,54 @@ &i2c5 {
 	status = "disabled";
 };
 
+&mdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				label = "lan0";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan1";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan2";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan3";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&gmac0>;
+				phy-mode = "rgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+	};
+};
+
 &mdio1 {
 	rgmii_phy1: ethernet-phy@0 {
 		compatible = "ethernet-phy-ieee802.3-c22";
Signature · 1 line
2.34.1
#13 lore raw
In reply to Frank Wunderlich
This series was applied to netdev/net-next.git (master) by Jakub Kicinski <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (master) by Jakub Kicinski <[email protected]>:

Quoted 8 lines · On Fri, 10 Jun 2022 19:05:35 +0200 you wrote:

From: Frank Wunderlich <[email protected]>

This Series add Support for the mt7531 switch on Bananapi R2 Pro board.

This board uses port5 of the switch to conect to the gmac0 of the rk3568 SoC.

[...]

Here is the summary with links:
- [v4,1/6] dt-bindings: net: dsa: convert binding for mediatek switches

    https://git.kernel.org/netdev/net-next/c/e0dda3119741
  - [v4,2/6] net: dsa: mt7530: rework mt7530_hw_vlan_{add,del}
    https://git.kernel.org/netdev/net-next/c/a9c317417c27
  - [v4,3/6] net: dsa: mt7530: rework mt753[01]_setup
    https://git.kernel.org/netdev/net-next/c/6e19bc26cccd
  - [v4,4/6] net: dsa: mt7530: get cpu-port via dp->cpu_dp instead of constant
    https://git.kernel.org/netdev/net-next/c/1f9a6abecf53
  - [v4,5/6] dt-bindings: net: dsa: make reset optional and add rgmii-mode to mt7531
    https://git.kernel.org/netdev/net-next/c/ae07485d7a1d
  - [v4,6/6] arm64: dts: rockchip: Add mt7531 dsa node to BPI-R2-Pro board
    https://git.kernel.org/netdev/net-next/c/c1804463e5c6

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html