mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
Subsystems (2)
v4 cover mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using chip_good() to chip_ready(), because DQ true data 0xFF is read on S29GL064N and an error returned by chip_good(). One way to solve the issue is to revert the change partially to use chip_ready for S29GL064N.
[1] https://lore.kernel.org/r/[email protected]/
Tokunori Ikegami (3):
mtd: cfi_cmdset_0002: Move and rename
chip_check/chip_ready/chip_good_for_write
mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
mtd: cfi_cmdset_0002: Add S29GL064N ID definition
drivers/mtd/chips/cfi_cmdset_0002.c | 93 +++++++++++++++-------------- 1 file changed, 49 insertions(+), 44 deletions(-)
Signature · 1 line
2.32.0
PATCH v4 1/3 mtd: cfi_cmdset_0002: Move and rename chip_check/chip_ready/chip_good_for_write
This is a preparation patch for the functional change in preparation to a change expected to fix the buffered writes on S29GL064N.
--- drivers/mtd/chips/cfi_cmdset_0002.c | 77 ++++++++++++----------------- 1 file changed, 32 insertions(+), 45 deletions(-)
drivers/mtd/chips/cfi_cmdset_0002.c +32 -45
@@ -801,22 +801,12 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)return NULL ; } -/* -* Return true if the chip is ready. -* -* Ready is one of: read mode, query mode, erase-suspend-read mode (in any -* non-suspended sector) and is indicated by no toggle bits toggling. -* -* Note that anything more complicated than checking if no bits are toggling -* (including checking DQ5 for an error status) is tricky to get working -* correctly and is therefore not done (particularly with interleaved chips -* as each chip must be checked independently of the others). -*/ -static int __xipram chip_ready(struct map_info *map, struct flchip *chip, -unsigned long addr) +static int __xipram chip_check(struct map_info *map, struct flchip *chip, +unsigned long addr,map_word *expected) {struct cfi_private *cfi = map->fldrv_priv; -map_word d, t; +map_word oldd, curd; +int ret;if (cfi_use_status_reg (cfi)) {map_word ready =CMD (CFI_SR_DRB );
@@ -826,17 +816,35 @@ static int __xipram chip_ready(struct map_info *map, struct flchip *chip,*/ cfi_send_gen_cmd (0x70 , cfi->addr_unlock1, chip->start, map, cfi, cfi->device_type,NULL ); - d =map_read (map, addr); + curd =map_read (map, addr); -return map_word_andequal (map, d, ready, ready); +return map_word_andequal (map, curd, ready, ready); } - d =map_read (map, addr); - t =map_read (map, addr); + oldd =map_read (map, addr); + curd =map_read (map, addr); + + ret =map_word_equal (map, oldd, curd); -return map_word_equal (map, d, t); +if (!ret || !expected) +return ret; + +return map_word_equal (map, curd, *expected); } +/* +* Return true if the chip is ready. +* +* Ready is one of: read mode, query mode, erase-suspend-read mode (in any +* non-suspended sector) and is indicated by no toggle bits toggling. +* +* Note that anything more complicated than checking if no bits are toggling +* (including checking DQ5 for an error status) is tricky to get working +* correctly and is therefore not done (particularly with interleaved chips +* as each chip must be checked independently of the others). +*/ +#define chip_ready (map, chip, addr) chip_check(map, chip, addr, NULL) +/* * Return true if the chip is ready and has the correct value. *
@@ -852,32 +860,11 @@ static int __xipram chip_ready(struct map_info *map, struct flchip *chip,* as each chip must be checked independently of the others). * */ -static int __xipram chip_good(struct map_info *map, struct flchip *chip, -unsigned long addr,map_word expected) -{ -struct cfi_private *cfi = map->fldrv_priv; -map_word oldd, curd; - -if (cfi_use_status_reg (cfi)) { -map_word ready =CMD (CFI_SR_DRB ); - -/* -* For chips that support status register, check device -* ready bit -*/ -cfi_send_gen_cmd (0x70 , cfi->addr_unlock1, chip->start, map, cfi, - cfi->device_type,NULL ); - curd =map_read (map, addr); - -return map_word_andequal (map, curd, ready, ready); - } - - oldd =map_read (map, addr); - curd =map_read (map, addr); - -return map_word_equal (map, oldd, curd) && -map_word_equal (map, curd, expected); -} +#define chip_good (map, chip, addr, expected) \ + ({ \ + map_word datum = expected; \ + chip_check(map, chip, addr, &datum); \ + })static int get_chip (struct map_info *map,struct flchip *chip,unsigned long adr,int mode) {
Signature · 1 line
2.32.0
Miquel Raynal
maintainerRe: [PATCH v4 1/3] mtd: cfi_cmdset_0002: Move and rename chip_check/chip_ready/chip_good_for_write
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:53 +0900:
Quoted 2 lines
This is a preparation patch for the functional change in preparation to a change expected to fix the buffered writes on S29GL064N.
This is a preparation patch for the S29GL064N buffer writes fix. There is no functional change.
Quoted 40 lines
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 77 ++++++++++++----------------- 1 file changed, 32 insertions(+), 45 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +4
-14@@ -801,22 +801,12 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)return NULL ; } -/* -* Return true if the chip is ready. -* -* Ready is one of: read mode, query mode, erase-suspend-read mode (in any -* non-suspended sector) and is indicated by no toggle bits toggling. -* -* Note that anything more complicated than checking if no bits are toggling -* (including checking DQ5 for an error status) is tricky to get working -* correctly and is therefore not done (particularly with interleaved chips -* as each chip must be checked independently of the others). -*/ -static int __xipram chip_ready(struct map_info *map, struct flchip *chip, -unsigned long addr) +static int __xipram chip_check(struct map_info *map, struct flchip *chip, +unsigned long addr,map_word *expected) {struct cfi_private *cfi = map->fldrv_priv; -map_word d, t; +map_word oldd, curd; +int ret;if (cfi_use_status_reg (cfi)) {map_word ready =CMD (CFI_SR_DRB );
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 821
Quoted 8 lines
drivers/mtd/chips/cfi_cmdset_0002.c +2
-2@@ -826,17 +816,35 @@ static int __xipram chip_ready(struct map_info *map, struct flchip *chip,*/ cfi_send_gen_cmd (0x70 , cfi->addr_unlock1, chip->start, map, cfi, cfi->device_type,NULL ); - d =map_read (map, addr); + curd =map_read (map, addr); -return map_word_andequal (map, d, ready, ready); +return map_word_andequal (map, curd, ready, ready);
A lot of the diff is just a rename. I am not against a rename if you feel it's better, but in this order:
1: prepare the fix
2: fix
3: rename/define id's, whatever
Quoted 18 lines
drivers/mtd/chips/cfi_cmdset_0002.c +10
-3} - d =map_read (map, addr); - t =map_read (map, addr); + oldd =map_read (map, addr); + curd =map_read (map, addr); + + ret =map_word_equal (map, oldd, curd); -return map_word_equal (map, d, t); +if (!ret || !expected) +return ret; + +return map_word_equal (map, curd, *expected); } +/* +* Return true if the chip is ready.
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 846
Quoted 10 lines
drivers/mtd/chips/cfi_cmdset_0002.c +10
-0+* +* Ready is one of: read mode, query mode, erase-suspend-read mode (in any +* non-suspended sector) and is indicated by no toggle bits toggling. +* +* Note that anything more complicated than checking if no bits are toggling +* (including checking DQ5 for an error status) is tricky to get working +* correctly and is therefore not done (particularly with interleaved chips +* as each chip must be checked independently of the others). +*/ +#define chip_ready (map, chip, addr) chip_check(map, chip, addr, NULL)
I don't see the point of such a define. Just get rid of it.
Quoted 29 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-21+/* * Return true if the chip is ready and has the correct value. * @@ -852,32 +860,11 @@ static int __xipram chip_ready(struct map_info *map, struct flchip *chip,* as each chip must be checked independently of the others). * */ -static int __xipram chip_good(struct map_info *map, struct flchip *chip, -unsigned long addr,map_word expected) -{ -struct cfi_private *cfi = map->fldrv_priv; -map_word oldd, curd; - -if (cfi_use_status_reg (cfi)) { -map_word ready =CMD (CFI_SR_DRB ); - -/* -* For chips that support status register, check device -* ready bit -*/ -cfi_send_gen_cmd (0x70 , cfi->addr_unlock1, chip->start, map, cfi, - cfi->device_type,NULL ); - curd =map_read (map, addr); - -return map_word_andequal (map, curd, ready, ready); - } - - oldd =map_read (map, addr);
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 867
Quoted 10 lines
drivers/mtd/chips/cfi_cmdset_0002.c +5
-5- curd =map_read (map, addr); - -return map_word_equal (map, oldd, curd) && -map_word_equal (map, curd, expected); -} +#define chip_good (map, chip, addr, expected) \ + ({ \ + map_word datum = expected; \ + chip_check(map, chip, addr, &datum); \ + })
What is this for? Same here, I don't see the point. Please get rid of all these unnecessary helpers which do nothing, besides complicating user's life.
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 870
Quoted 2 lines
drivers/mtd/chips/cfi_cmdset_0002.c +0
-0static int get_chip (struct map_info *map,struct flchip *chip,unsigned long adr,int mode) {
Thanks,
Miquèl
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Re: [PATCH v4 1/3] mtd: cfi_cmdset_0002: Move and rename chip_check/chip_ready/chip_good_for_write
Hi Miquèl-san,
Quoted 8 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:53 +0900:
Quoted 2 lines
This is a preparation patch for the functional change in preparation to a change expected to fix the buffered writes on S29GL064N.
This is a preparation patch for the S29GL064N buffer writes fix. There is no functional change.
Fixed this by the version 5 patch.
Quoted 46 lines
Quoted 46 lines
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 77 ++++++++++++----------------- 1 file changed, 32 insertions(+), 45 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +5
-15@@ -801,22 +801,12 @@ static struct mtd_info *cfi_amdstd_setup(struct mtd_info *mtd)return NULL ; } -/* -* Return true if the chip is ready. -* -* Ready is one of: read mode, query mode, erase-suspend-read mode (in any -* non-suspended sector) and is indicated by no toggle bits toggling. -* -* Note that anything more complicated than checking if no bits are toggling -* (including checking DQ5 for an error status) is tricky to get working -* correctly and is therefore not done (particularly with interleaved chips -* as each chip must be checked independently of the others). -*/ -static int __xipram chip_ready(struct map_info *map, struct flchip *chip, -unsigned long addr) +static int __xipram chip_check(struct map_info *map, struct flchip *chip, +unsigned long addr,map_word *expected) {struct cfi_private *cfi = map->fldrv_priv; -map_word d, t; +map_word oldd, curd; +int ret;if (cfi_use_status_reg (cfi)) {map_word ready =CMD (CFI_SR_DRB );@@ -826,17 +816,35 @@ static int __xipram chip_ready(struct map_info *map, struct flchip *chip,*/ cfi_send_gen_cmd (0x70 , cfi->addr_unlock1, chip->start, map, cfi, cfi->device_type,NULL ); - d =map_read (map, addr); + curd =map_read (map, addr);
Quoted 7 lines
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 821
Quoted 2 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-1-return map_word_andequal (map, d, ready, ready); +return map_word_andequal (map, curd, ready, ready);A lot of the diff is just a rename. I am not against a rename if you feel it's better, but in this order:
1: prepare the fix
2: fix
3: rename/define id's, whatever
This is also fixed as same.
Quoted 17 lines
Quoted 17 lines
drivers/mtd/chips/cfi_cmdset_0002.c +8
-3} - d =map_read (map, addr); - t =map_read (map, addr); + oldd =map_read (map, addr); + curd =map_read (map, addr); + + ret =map_word_equal (map, oldd, curd); -return map_word_equal (map, d, t); +if (!ret || !expected) +return ret; + +return map_word_equal (map, curd, *expected); }
Quoted 13 lines
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 846
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+/* +* Return true if the chip is ready. +* +* Ready is one of: read mode, query mode, erase-suspend-read mode (in any +* non-suspended sector) and is indicated by no toggle bits toggling. +* +* Note that anything more complicated than checking if no bits are toggling +* (including checking DQ5 for an error status) is tricky to get working +* correctly and is therefore not done (particularly with interleaved chips +* as each chip must be checked independently of the others). +*/ +#define chip_ready (map, chip, addr) chip_check(map, chip, addr, NULL)I don't see the point of such a define. Just get rid of it.
Yes deleted the macro as changed the name chip_check to chip_ready and to use only chip_ready without the macro.
Quoted 35 lines
Quoted 35 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-26+/* * Return true if the chip is ready and has the correct value. * @@ -852,32 +860,11 @@ static int __xipram chip_ready(struct map_info *map, struct flchip *chip,* as each chip must be checked independently of the others). * */ -static int __xipram chip_good(struct map_info *map, struct flchip *chip, -unsigned long addr,map_word expected) -{ -struct cfi_private *cfi = map->fldrv_priv; -map_word oldd, curd; - -if (cfi_use_status_reg (cfi)) { -map_word ready =CMD (CFI_SR_DRB ); - -/* -* For chips that support status register, check device -* ready bit -*/ -cfi_send_gen_cmd (0x70 , cfi->addr_unlock1, chip->start, map, cfi, - cfi->device_type,NULL ); - curd =map_read (map, addr); - -return map_word_andequal (map, curd, ready, ready); - } - - oldd =map_read (map, addr); - curd =map_read (map, addr); - -return map_word_equal (map, oldd, curd) && -map_word_equal (map, curd, expected); -}
Quoted 8 lines
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 867
Quoted 5 lines
drivers/mtd/chips/cfi_cmdset_0002.c +5
-0+#define chip_good (map, chip, addr, expected) \ + ({ \ + map_word datum = expected; \ + chip_check(map, chip, addr, &datum); \ + })What is this for? Same here, I don't see the point. Please get rid of all these unnecessary helpers which do nothing, besides complicating user's life.
Fixed as same.
Regards,
Ikegami
Quoted 6 lines
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_ready(struct map_info *map, struct flchip *chip, · line 870
Quoted 3 lines
drivers/mtd/chips/cfi_cmdset_0002.c +0
-0static int get_chip (struct map_info *map,struct flchip *chip,unsigned long adr,int mode) {Thanks,
Miquèl
PATCH v4 2/3 mtd: cfi_cmdset_0002: Use chip_ready() for write on S29GL064N
In reply to Tokunori IkegamiAs pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using chip_good() to chip_ready(), because DQ true data 0xFF is read on S29GL064N and an error returned by chip_good(). One way to solve the issue is to revert the change partially to use chip_ready for S29GL064N.
[1] https://lore.kernel.org/r/[email protected]/
--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)
drivers/mtd/chips/cfi_cmdset_0002.c +21 -4
@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map) +{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr); + +return chip_good (map, chip, addr, expected); +} +static int get_chip (struct map_info *map,struct flchip *chip,unsigned long adr,int mode) {DECLARE_WAITQUEUE (wait, current);
@@ -1686,7 +1703,7 @@ static int __xipram do_write_oneword_once(struct map_info *map,* "chip_good" to avoid the failure due to scheduling. */ if (time_after (jiffies, timeo) && - !chip_good (map, chip, adr, datum)) { + !chip_good_for_write (map, chip, adr, datum)) {xip_enable (map, chip, adr);printk (KERN_WARNING "MTD %s(): software timeout\n" , __func__);xip_disable (map, chip, adr);
@@ -1694,7 +1711,7 @@ static int __xipram do_write_oneword_once(struct map_info *map,break ; } -if (chip_good (map, chip, adr, datum)) { +if (chip_good_for_write (map, chip, adr, datum)) {if (cfi_check_err_status (map, chip, adr)) ret = -EIO ;break ;
@@ -1966,14 +1983,14 @@ static int __xipram do_write_buffer_wait(struct map_info *map,* "chip_good" to avoid the failure due to scheduling. */ if (time_after (jiffies, timeo) && - !chip_good (map, chip, adr, datum)) { + !chip_good_for_write (map, chip, adr, datum)) {pr_err ("MTD %s(): software timeout, address:0x%.8lx.\n" , __func__, adr); ret = -EIO ;break ; } -if (chip_good (map, chip, adr, datum)) { +if (chip_good_for_write (map, chip, adr, datum)) {if (cfi_check_err_status (map, chip, adr)) ret = -EIO ;break ;
Signature · 1 line
2.32.0
Miquel Raynal
maintainerHi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().
Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
Quoted 18 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 869
Quoted 4 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)
At the very least I would call this function:cfi_use_chip_ready_for_writes()
Yet, I still don't fully get what chip_ready is versus chip_good.
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr);
If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this cfi_use_chip_ready_for_write() check.
Anyway, I would move this to the chip_good() implementation directly so we partially hide the quirks complexity from the core.
Quoted 32 lines
drivers/mtd/chips/cfi_cmdset_0002.c +7
-3+ +return chip_good (map, chip, addr, expected); +} +static int get_chip (struct map_info *map,struct flchip *chip,unsigned long adr,int mode) {DECLARE_WAITQUEUE (wait, current);@@ -1686,7 +1703,7 @@ static int __xipram do_write_oneword_once(struct map_info *map,* "chip_good" to avoid the failure due to scheduling. */ if (time_after (jiffies, timeo) && - !chip_good (map, chip, adr, datum)) { + !chip_good_for_write (map, chip, adr, datum)) {xip_enable (map, chip, adr);printk (KERN_WARNING "MTD %s(): software timeout\n" , __func__);xip_disable (map, chip, adr);@@ -1694,7 +1711,7 @@ static int __xipram do_write_oneword_once(struct map_info *map,break ; } -if (chip_good (map, chip, adr, datum)) { +if (chip_good_for_write (map, chip, adr, datum)) {if (cfi_check_err_status (map, chip, adr)) ret = -EIO ;break ;@@ -1966,14 +1983,14 @@ static int __xipram do_write_buffer_wait(struct map_info *map,* "chip_good" to avoid the failure due to scheduling. */ if (time_after (jiffies, timeo) && - !chip_good (map, chip, adr, datum)) { + !chip_good_for_write (map, chip, adr, datum)) { pr_err("MTD %s(): software timeout, address:0x%.8lx.\n",
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram do_write_buffer_wait(struct map_info *map, · line 1996
Quoted 10 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-1__func__, adr); ret = -EIO ;break ; } -if (chip_good (map, chip, adr, datum)) { +if (chip_good_for_write (map, chip, adr, datum)) {if (cfi_check_err_status (map, chip, adr)) ret = -EIO ;break ;
Thanks,
Miquèl
Vignesh Raghavendra
maintainerQuoted 11 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
How about:
Since commit dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value") buffered writes fail on S29GL064N. This is because, on S29GL064N, reads return 0xFF at the end of DQ polling for write completion, where as, chip_good() check expects actual data written to the last location to be returned post DQ polling completion. Fix is to revert to using chip_good() for S29GL064N which only checks for DQ lines to settle down to determine write completion.
Quoted 45 lines
Quoted 19 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 869
Quoted 4 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.
Quoted 2 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.
Yeah, unfortunately this driver does not use quirk flags and tends to hide quirks behind bool functions like above
Regards
Vignesh
Hello Vignesh,
Quoted 17 lines · Vignesh Raghavendra
Quoted 11 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
How about:
Quoted 7 lines
Since commit
dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")buffered writes fail on S29GL064N. This is because, on S29GL064N, reads return0xFFat the end of DQ polling for write completion, where as,chip_good()check expects actual data written to the last location to be returned post DQ polling completion. Fix is to revert to usingchip_good()for S29GL064N which only checks for DQ lines to settle down to determine write completion.
Message sounds good to me with one remark: The issue is independent of whether buffered writes are used or not. It's just because buffered writes are the default, that it was broken by dfeae1073583 ("mtd: cfi_cmdset_0002:
Change write buffer to check correct value"). The word write case was broken by 37c673ade35c ("mtd: cfi_cmdset_0002: Use chip_good() to retry in do_write_oneword()"), so the commit message should probably reference both. as this commit indeed fixes both FORCE_WORD_WRITE == 0 and == 1.
Thanks,
Ahmad
Quoted 55 lines
Quoted 46 lines
Quoted 20 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 869
Quoted 4 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.Quoted 2 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.Yeah, unfortunately this driver does not use quirk flags and tends to hide quirks behind bool functions like above
Regards
Vignesh
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi Ahmad-san,
Quoted 24 lines · Ahmad Fatoum
Hello Vignesh,
Quoted 14 lines · Vignesh Raghavendra
Quoted 10 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
How about:
Quoted 7 lines
Since commit
dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")buffered writes fail on S29GL064N. This is because, on S29GL064N, reads return0xFFat the end of DQ polling for write completion, where as,chip_good()check expects actual data written to the last location to be returned post DQ polling completion. Fix is to revert to usingchip_good()for S29GL064N which only checks for DQ lines to settle down to determine write completion.
Quoted 7 lines
Message sounds good to me with one remark: The issue is independent of whether buffered writes are used or not. It's just because buffered writes are the default, that it was broken by
dfeae1073583("mtd:cfi_cmdset_0002:
Change write buffer to check correct value"). The word write case was broken by37c673ade35c("mtd:cfi_cmdset_0002: Usechip_good()to retry indo_write_oneword()"), so the commit message should probably reference both. as this commit indeed fixes bothFORCE_WORD_WRITE== 0 and == 1.
Is this really caused the error on do_write_oneword by the changed? Actually it was changed to use chip_good instead of chip_ready.
But before the change still do_write_oneword uses both chip_ready and chip_good. So it seems that it is possible to be caused the error before the change also.
By the way could you please try to test the version 5 patches again?
Regards,
Ikegami
Quoted 56 lines
Thanks,
AhmadQuoted 50 lines
Quoted 42 lines
Quoted 18 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 869
Quoted 4 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.Quoted 2 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.Yeah, unfortunately this driver does not use quirk flags and tends to hide quirks behind bool functions like above
Regards
Vignesh
Quoted 35 lines · Tokunori Ikegami
Hi Ahmad-san,
Quoted 24 lines · Ahmad Fatoum
Hello Vignesh,
Quoted 14 lines · Vignesh Raghavendra
Quoted 10 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
How about:
Quoted 7 lines
Since commit
dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")buffered writes fail on S29GL064N. This is because, on S29GL064N, reads return0xFFat the end of DQ polling for write completion, where as,chip_good()check expects actual data written to the last location to be returned post DQ polling completion. Fix is to revert to usingchip_good()for S29GL064N which only checks for DQ lines to settle down to determine write completion.Quoted 7 lines
Message sounds good to me with one remark: The issue is independent of whether buffered writes are used or not. It's just because buffered writes are the default, that it was broken by
dfeae1073583("mtd:cfi_cmdset_0002:
Change write buffer to check correct value"). The word write case was broken by37c673ade35c("mtd:cfi_cmdset_0002: Usechip_good()to retry indo_write_oneword()"), so the commit message should probably reference both. as this commit indeed fixes bothFORCE_WORD_WRITE== 0 and == 1.
Quoted 4 lines
Is this really caused the error on
do_write_onewordby the changed? Actually it was changed to usechip_goodinstead ofchip_ready.
But before the change stilldo_write_oneworduses bothchip_readyandchip_good. So it seems that it is possible to be caused the error before the change also.
Oh, I think you're right. Disregard my suggestion for the other
Fixes: entry then.
Quoted 1 line
By the way could you please try to test the version 5 patches again?
Just did so for v7. Sorry for the delay.
Cheers,
Ahmad
Quoted 60 lines
Regards,
IkegamiQuoted 55 lines
Thanks,
AhmadQuoted 49 lines
Quoted 41 lines
Quoted 18 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>---
drivers/mtd/chips/cfi_cmdset_0002.c| 25 +++++++++++++++++++++----1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 868
Quoted 3 lines
drivers/mtd/chips/cfi_cmdset_0002.c +0
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip, chip_check(map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ + struct cfi_private *cfi = map->fldrv_priv; + + return cfi->mfr == CFI_MFR_AMD && cfi->id == 0x0c01; +} + +static int __xipram chip_good_for_write(struct map_info *map, + struct flchip *chip, unsigned long addr, + map_word expected) +{ + if (cfi_use_chip_ready_for_write(map)) + return chip_ready(map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.Quoted 2 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.Yeah, unfortunately this driver does not use quirk flags and tends to hide quirks behind bool functions like above
Regards
Vignesh
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi Ahmad-san,
Quoted 34 lines · Ahmad Fatoum
Quoted 33 lines · Tokunori Ikegami
Hi Ahmad-san,
Quoted 30 lines · Ahmad Fatoum
Hello Vignesh,
Quoted 13 lines · Vignesh Raghavendra
Quoted 10 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
How about:
Quoted 7 lines
Since commit
dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")buffered writes fail on S29GL064N. This is because, on S29GL064N, reads return0xFFat the end of DQ polling for write completion, where as,chip_good()check expects actual data written to the last location to be returned post DQ polling completion. Fix is to revert to usingchip_good()for S29GL064N which only checks for DQ lines to settle down to determine write completion.Message sounds good to me with one remark: The issue is independent of whether buffered writes are used or not. It's just because buffered writes are the default, that it was broken by
dfeae1073583("mtd:cfi_cmdset_0002:
Change write buffer to check correct value"). The word write case was broken by37c673ade35c("mtd:cfi_cmdset_0002: Usechip_good()to retry indo_write_oneword()"), so the commit message should probably reference both. as this commit indeed fixes bothFORCE_WORD_WRITE== 0 and == 1.
Quoted 6 lines
Quoted 4 lines
Is this really caused the error on
do_write_onewordby the changed? Actually it was changed to usechip_goodinstead ofchip_ready.
But before the change stilldo_write_oneworduses bothchip_readyandchip_good. So it seems that it is possible to be caused the error before the change also.Oh, I think you're right. Disregard my suggestion for the other
Fixes: entry then.
Thanks for the confirmation.
Quoted 3 lines
Quoted 2 lines
By the way could you please try to test the version 5 patches again?
Just did so for v7. Sorry for the delay.
Thank you so much for your help. Sorry I missed to cc on version 5 to version 7 patches.
Regards,
Ikegami
Quoted 61 lines
Cheers,
AhmadQuoted 56 lines
Regards,
IkegamiQuoted 53 lines
Thanks,
AhmadQuoted 49 lines
Quoted 41 lines
Quoted 18 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 868
Quoted 3 lines
drivers/mtd/chips/cfi_cmdset_0002.c +0
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip, chip_check(map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ + struct cfi_private *cfi = map->fldrv_priv; + + return cfi->mfr == CFI_MFR_AMD && cfi->id == 0x0c01; +} + +static int __xipram chip_good_for_write(struct map_info *map, + struct flchip *chip, unsigned long addr, + map_word expected) +{ + if (cfi_use_chip_ready_for_write(map)) + return chip_ready(map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.Quoted 2 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.Yeah, unfortunately this driver does not use quirk flags and tends to hide quirks behind bool functions like above
Regards
Vignesh
Hi,
Quoted 14 lines · Vignesh Raghavendra
Quoted 10 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
How about:
Quoted 7 lines
Since commit
dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")buffered writes fail on S29GL064N. This is because, on S29GL064N, reads return0xFFat the end of DQ polling for write completion, where as,chip_good()check expects actual data written to the last location to be returned post DQ polling completion. Fix is to revert to usingchip_good()for S29GL064N which only checks for DQ lines to settle down to determine write completion.
Fixed the commit message as suggested by the version 5 patch.
Quoted 42 lines
Quoted 42 lines
Quoted 18 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 869
Quoted 4 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ }) +static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 12 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.
Quoted 4 lines
Quoted 2 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.Yeah, unfortunately this driver does not use quirk flags and tends to hide quirks behind bool functions like above
Added the quirks flag as mentioned.
Regards,
Ikegami
Quoted 3 lines
Regards
Vignesh
Hi Miquèl-san,
Quoted 32 lines · Miquel Raynal
Hi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:54 +0900:
Quoted 4 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good().Vignesh, I believe you understand this issue better than I do, can you propose an improved commit log?
Quoted 21 lines
One way to solve the issue is to revert the change partially to use
chip_readyfor S29GL064N.[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>--- drivers/mtd/chips/cfi_cmdset_0002.c | 25 +++++++++++++++++++++---- 1 file changed, 21 insertions(+), 4 deletions(-)drivers/mtd/chips/cfi_cmdset_0002.c +0
-0@@ -866,6 +866,23 @@ static int __xipram chip_check(struct map_info *map, struct flchip *chip,chip_check (map, chip, addr, &datum); \ })
Quoted 5 lines
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 869
Quoted 1 line
drivers/mtd/chips/cfi_cmdset_0002.c +1
-0+static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map)At the very least I would call this function:
cfi_use_chip_ready_for_writes()Yet, I still don't fully get what
chip_readyis versuschip_good.
This was deleted as to use the quirks flag instead.
Quoted 15 lines
drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram chip_check(struct map_info *map, struct flchip *chip, · line 881
Quoted 13 lines
drivers/mtd/chips/cfi_cmdset_0002.c +12
-0+{ +struct cfi_private *cfi = map->fldrv_priv; + +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +} + +static int __xipram chip_good_for_write(struct map_info *map, +struct flchip *chip,unsigned long addr, +map_word expected) +{ +if (cfi_use_chip_ready_for_write (map)) +return chip_ready (map, chip, addr);If possible and not too invasive I would definitely add a "quirks" flag somewhere instead of this
cfi_use_chip_ready_for_write()check.
Added the quirks flag by the version 5 patch.
Quoted 3 lines
Anyway, I would move this to the
chip_good()implementation directly so we partially hide the quirks complexity from the core.
Yes also added the chip_good to check the quirks flag.
Regards,
Ikegami
Quoted 46 lines
Quoted 33 lines
drivers/mtd/chips/cfi_cmdset_0002.c +7
-3+ +return chip_good (map, chip, addr, expected); +} +static int get_chip (struct map_info *map,struct flchip *chip,unsigned long adr,int mode) {DECLARE_WAITQUEUE (wait, current);@@ -1686,7 +1703,7 @@ static int __xipram do_write_oneword_once(struct map_info *map,* "chip_good" to avoid the failure due to scheduling. */ if (time_after (jiffies, timeo) && - !chip_good (map, chip, adr, datum)) { + !chip_good_for_write (map, chip, adr, datum)) {xip_enable (map, chip, adr);printk (KERN_WARNING "MTD %s(): software timeout\n" , __func__);xip_disable (map, chip, adr);@@ -1694,7 +1711,7 @@ static int __xipram do_write_oneword_once(struct map_info *map,break ; } -if (chip_good (map, chip, adr, datum)) { +if (chip_good_for_write (map, chip, adr, datum)) {if (cfi_check_err_status (map, chip, adr)) ret = -EIO ;break ;@@ -1966,14 +1983,14 @@ static int __xipram do_write_buffer_wait(struct map_info *map,* "chip_good" to avoid the failure due to scheduling. */ if (time_after (jiffies, timeo) && - !chip_good (map, chip, adr, datum)) { + !chip_good_for_write (map, chip, adr, datum)) { pr_err("MTD %s(): software timeout, address:0x%.8lx.\n",drivers/mtd/chips/cfi_cmdset_0002.c static int __xipram do_write_buffer_wait(struct map_info *map, · line 1996
Quoted 10 lines
drivers/mtd/chips/cfi_cmdset_0002.c +1
-1__func__, adr); ret = -EIO ;break ; } -if (chip_good (map, chip, adr, datum)) { +if (chip_good_for_write (map, chip, adr, datum)) {if (cfi_check_err_status (map, chip, adr)) ret = -EIO ;break ;Thanks,
Miquèl
Quoted 7 lines · Tokunori Ikegami
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.
Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/
) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Link:
https://lore.kernel.org/r/[email protected]/
[1]
Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/
Miquel Raynal
maintainerHi Thorsten,
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 19 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Quoted 9 lines
Link:
https://lore.kernel.org/r/[email protected]/
[1]Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/
Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied. I then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?
Thanks,
Miquèl
Quoted 26 lines · Miquel Raynal
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 23 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Quoted 8 lines
Quoted 5 lines
Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied.
That can be an additional Link tag, that is done all the time.
Quoted 3 lines
I
then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?
But it's not your own project, we are all working with thousands of people together on this project on various different fronts. That needs coordination, as some things otherwise become hard or impossible. That's why we have documentation that explains how to do some things. Not following it just because you don't like it is not helpful and in this case makes my life as a volunteer a lot harder.
If you don't like the approach explained by the documentation, submit a patch adjusting the documentation and then we can talk about this. But until that is applied please stick to the format explained by the documentation.
Ciao, Thorsten
Miquel Raynal
maintainerThorsten,
[email protected] wrote on Mon, 21 Mar 2022 13:51:10 +0100:
Quoted 29 lines · Miquel Raynal
Quoted 28 lines
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 25 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Link:
https://lore.kernel.org/r/[email protected]/
[1]Ciao, Thorsten
Quoted 12 lines
Quoted 6 lines
Quoted 3 lines
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied.
That can be an additional Link tag, that is done all the time.
Quoted 3 lines
I
then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?
Perhaps I should emphasize that I don't remember your initial request regarding the use of a Link tag and my original idea was to help this contributor, not kill your tools which I actually know very little about.
Quoted 6 lines
But it's not your own project, we are all working with thousands of people together on this project on various different fronts. That needs coordination, as some things otherwise become hard or impossible. That's why we have documentation that explains how to do some things. Not following it just because you don't like it is not helpful and in this case makes my life as a volunteer a lot harder.
Let's be honest, you are referring to a Documentation patch that *you* wrote and was merged into Linus' tree mid January. How often do you think people used to the contribution workflow monitor these files?
I am totally fine enforcing the use of Link: tags if this is what has been decided, just don't expect everybody to switch to a style rather than another over a night.
Quoted 4 lines
If you don't like the approach explained by the documentation, submit a patch adjusting the documentation and then we can talk about this. But until that is applied please stick to the format explained by the documentation.
This is uselessly condescending.
Thanks,
Miquèl
Quoted 36 lines · Miquel Raynal
[email protected] wrote on Mon, 21 Mar 2022 13:51:10 +0100:
Quoted 35 lines · Miquel Raynal
Quoted 33 lines
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 19 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Quoted 9 lines
Link:
https://lore.kernel.org/r/[email protected]/
[1]Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied.
Quoted 8 lines
Quoted 5 lines
That can be an additional Link tag, that is done all the time.
Quoted 3 lines
I
then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?Perhaps I should emphasize that I don't remember your initial request regarding the use of a Link tag
Happen, no worries.
Quoted 4 lines
and my original idea was to help this
contributor, not kill your tools which I actually know very little about.Quoted 1 line
Quoted 1 line
But it's not your own project, we are all working with thousands of
Quoted 8 lines
Quoted 5 lines
people together on this project on various different fronts. That needs coordination, as some things otherwise become hard or impossible. That's why we have documentation that explains how to do some things. Not following it just because you don't like it is not helpful and in this case makes my life as a volunteer a lot harder.
Let's be honest, you are referring to a Documentation patch that *you* wrote
Correct, but in case of submitting-patches it was just a clarification how to place links; why the whole aspect was missing in the other is kinda odd and likely lost in history...
Quoted 2 lines
and was merged into Linus' tree mid January. How often do you think people used to the contribution workflow monitor these files?
Not often, that's why I have no problem pointing it out, even if that's slightly annoying. But you can imagine that it felt kinda odd on my side when asking someone to set the links (with references to the docs explaining how to set them) and seeing them added then in v2, just so see they vanished again in v3 of the same patch. :-/
Quoted 3 lines
I am totally fine enforcing the use of Link: tags if this is what has been decided, just don't expect everybody to switch to a style rather than another over a night.
I don't.
Quoted 5 lines
Quoted 4 lines
If you don't like the approach explained by the documentation, submit a patch adjusting the documentation and then we can talk about this. But until that is applied please stick to the format explained by the documentation.
This is uselessly condescending.
I apologize, it wasn't meant that way. I had to many discussions already where people were not setting any links and it seems the topic is slowly hitting a nerve here. Sorry.
Ciao, Thorsten
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Miquel Raynal
maintainerHi Thorsten,
[email protected] wrote on Mon, 21 Mar 2022 15:17:50 +0100:
Quoted 65 lines · Miquel Raynal
Quoted 36 lines
[email protected] wrote on Mon, 21 Mar 2022 13:51:10 +0100:
Quoted 35 lines · Miquel Raynal
Quoted 33 lines
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 19 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Quoted 9 lines
Link:
https://lore.kernel.org/r/[email protected]/
[1]Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied.
Quoted 8 lines
Quoted 5 lines
That can be an additional Link tag, that is done all the time.
Quoted 3 lines
I
then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?Perhaps I should emphasize that I don't remember your initial request regarding the use of a Link tag
Happen, no worries.
Quoted 4 lines
and my original idea was to help this
contributor, not kill your tools which I actually know very little about.Quoted 1 line
Quoted 1 line
But it's not your own project, we are all working with thousands of
Quoted 8 lines
Quoted 5 lines
people together on this project on various different fronts. That needs coordination, as some things otherwise become hard or impossible. That's why we have documentation that explains how to do some things. Not following it just because you don't like it is not helpful and in this case makes my life as a volunteer a lot harder.
Let's be honest, you are referring to a Documentation patch that *you* wrote
Correct, but in case of submitting-patches it was just a clarification how to place links; why the whole aspect was missing in the other is kinda odd and likely lost in history...
Quoted 8 lines
Quoted 2 lines
and was merged into Linus' tree mid January. How often do you think people used to the contribution workflow monitor these files?
Not often, that's why I have no problem pointing it out, even if that's slightly annoying. But you can imagine that it felt kinda odd on my side when asking someone to set the links (with references to the docs explaining how to set them) and seeing them added then in v2, just so see they vanished again in v3 of the same patch. :-/
I fully understand. I actually learned that these tags had to be used for this purpose, so I will actually enforce their use in my next reviews.
Just a side question, should the Documentation also mention how to refer to links for people not used to it? Something like [5.Posting.rst]:
"Link: <link> [1] Link: <link> [2]"
My original point was that maintainers would almost always add a Link tag at the end, containing the mailing-list thread about the patch being applied. Just saying in the commit log "see the link below" then becomes misleading.
Quoted 6 lines
Quoted 3 lines
I am totally fine enforcing the use of Link: tags if this is what has been decided, just don't expect everybody to switch to a style rather than another over a night.
I don't.
Quoted 7 lines
Quoted 5 lines
Quoted 4 lines
If you don't like the approach explained by the documentation, submit a patch adjusting the documentation and then we can talk about this. But until that is applied please stick to the format explained by the documentation.
This is uselessly condescending.
I apologize, it wasn't meant that way.
No worries, thanks :-)
Quoted 3 lines
I had to many discussions already
where people were not setting any links and it seems the topic is slowly hitting a nerve here. Sorry.
I also feel like I am repeating myself sometimes. And then I remember Rob and the ton of e-mails where he has to repeat himself hundreds of times a day and I feel slightly better :-p
Cheers, Miquèl
Quoted 79 lines · Miquel Raynal
[email protected] wrote on Mon, 21 Mar 2022 15:17:50 +0100:
Quoted 65 lines · Miquel Raynal
Quoted 36 lines
[email protected] wrote on Mon, 21 Mar 2022 13:51:10 +0100:
Quoted 35 lines · Miquel Raynal
Quoted 33 lines
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 19 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Quoted 9 lines
Link:
https://lore.kernel.org/r/[email protected]/
[1]Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied.
Quoted 8 lines
Quoted 5 lines
That can be an additional Link tag, that is done all the time.
Quoted 3 lines
I
then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?Perhaps I should emphasize that I don't remember your initial request regarding the use of a Link tag
Happen, no worries.
Quoted 4 lines
and my original idea was to help this
contributor, not kill your tools which I actually know very little about.Quoted 1 line
Quoted 1 line
But it's not your own project, we are all working with thousands of
Quoted 8 lines
Quoted 5 lines
people together on this project on various different fronts. That needs coordination, as some things otherwise become hard or impossible. That's why we have documentation that explains how to do some things. Not following it just because you don't like it is not helpful and in this case makes my life as a volunteer a lot harder.
Let's be honest, you are referring to a Documentation patch that *you* wrote
Correct, but in case of submitting-patches it was just a clarification how to place links; why the whole aspect was missing in the other is kinda odd and likely lost in history...
Quoted 8 lines
Quoted 2 lines
and was merged into Linus' tree mid January. How often do you think people used to the contribution workflow monitor these files?
Not often, that's why I have no problem pointing it out, even if that's slightly annoying. But you can imagine that it felt kinda odd on my side when asking someone to set the links (with references to the docs explaining how to set them) and seeing them added then in v2, just so see they vanished again in v3 of the same patch. :-/
I fully understand. I actually learned that these tags had to be used for this purpose, so I will actually enforce their use in my next reviews.
Quoted 6 lines
Just a side question, should the Documentation also mention how to refer to links for people not used to it? Something like [
5.Posting.rst]:"Link: <link> [1] Link: <link> [2]"
Maybe. But I think the better approach would be: introduce more specify tags like "Reported:" (and maybe drop "Reported-by" at the same time?) or "BugLink" (some people use that already!) would be better -- and then maybe "Posted:", "Reviewposting", or something like that for the link to the patch that is being applied; and leave "Link" for the rest. I proposed that a while ago, but that didn't get any traction.
Quoted 4 lines
My original point was that maintainers would almost always add a Link tag at the end, containing the mailing-list thread about the patch being applied. Just saying in the commit log "see the link below" then becomes misleading.
Maybe, but OTOH that link is normally at the end, which kinda makes it obvious.
Quoted 1 line
[...]
Ciao, Thorsten
Hi,
Quoted 75 lines · Thorsten Leemhuis
Quoted 74 lines · Miquel Raynal
[email protected] wrote on Mon, 21 Mar 2022 15:17:50 +0100:
Quoted 58 lines · Miquel Raynal
Quoted 33 lines
[email protected] wrote on Mon, 21 Mar 2022 13:51:10 +0100:
Quoted 32 lines · Miquel Raynal
Quoted 31 lines
[email protected] wrote on Mon, 21 Mar 2022 12:48:11 +0100:
Quoted 18 lines · Tokunori Ikegami
Quoted 7 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.Why did you switch from the documented format for links you added on my request (see
https://lore.kernel.org/stable/[email protected]/) to v2 to something else that is not recognized by tools and scripts that rely on proper link tags? You are making my and maybe other peoples life unnecessary hard. :-((
FWIW, the proper style should support footnote style like this:
Quoted 9 lines
Link:
https://lore.kernel.org/r/[email protected]/
[1]Ciao, Thorsten
#regzbot ^backmonitor:
https://lore.kernel.org/r/[email protected]/Because today's requirement from maintainers is to provide a Link tag that points to the mail discussion of the patch being applied.
Quoted 7 lines
Quoted 5 lines
That can be an additional Link tag, that is done all the time.
Quoted 3 lines
I
then asked to use the above form instead to point to the bug report because I don't see the point of having a "Link" tag for it?Perhaps I should emphasize that I don't remember your initial request regarding the use of a Link tag
Happen, no worries.
Quoted 11 lines
and my original idea was to help this
contributor, not kill your tools which I actually know very little about.Quoted 6 lines
Quoted 1 line
But it's not your own project, we are all working with thousands of
people together on this project on various different fronts. That needs coordination, as some things otherwise become hard or impossible. That's why we have documentation that explains how to do some things. Not following it just because you don't like it is not helpful and in this case makes my life as a volunteer a lot harder.
Let's be honest, you are referring to a Documentation patch that *you* wrote
Correct, but in case of submitting-patches it was just a clarification how to place links; why the whole aspect was missing in the other is kinda odd and likely lost in history...
Quoted 7 lines
Quoted 2 lines
and was merged into Linus' tree mid January. How often do you think people used to the contribution workflow monitor these files?
Not often, that's why I have no problem pointing it out, even if that's slightly annoying. But you can imagine that it felt kinda odd on my side when asking someone to set the links (with references to the docs explaining how to set them) and seeing them added then in v2, just so see they vanished again in v3 of the same patch. :-/
I fully understand. I actually learned that these tags had to be used for this purpose, so I will actually enforce their use in my next reviews.
Just a side question, should the Documentation also mention how to refer to links for people not used to it? Something like [
5.Posting.rst]:
Quoted 8 lines
Quoted 2 lines
"Link: <link> [1] Link: <link> [2]"Maybe. But I think the better approach would be: introduce more specify tags like "Reported:" (and maybe drop "Reported-by" at the same time?) or "BugLink" (some people use that already!) would be better -- and then maybe "Posted:", "Reviewposting", or something like that for the link to the patch that is being applied; and leave "Link" for the rest. I proposed that a while ago, but that didn't get any traction.
Fixed to use Link tag as before by the version 5 patches instead of [1].
Regards,
Ikegami
Quoted 10 lines
Quoted 5 lines
My original point was that maintainers would almost always add a Link tag at the end, containing the mailing-list thread about the patch being applied. Just saying in the commit log "see the link below" then becomes misleading.
Maybe, but OTOH that link is normally at the end, which kinda makes it obvious.
Quoted 1 line
[...]
Ciao, Thorsten
PATCH v4 3/3 mtd: cfi_cmdset_0002: Add S29GL064N ID definition
In reply to Tokunori IkegamiIt is for the model number 01, 02, V1 and V2.
--- drivers/mtd/chips/cfi_cmdset_0002.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/mtd/chips/cfi_cmdset_0002.c +3 -2
@@ -48,6 +48,7 @@#define SST49LF040B 0x0050#define SST49LF008A 0x005a#define AT49BV6416 0x00d6 +#define S29GL064N_MN12 0x0c01/* * Status Register bit description. Used by flash devices that don't
@@ -462,7 +463,7 @@ static struct cfi_fixup cfi_fixup_table[] = { { CFI_MFR_AMD, 0x0056, fixup_use_secsi }, { CFI_MFR_AMD, 0x005C, fixup_use_secsi }, { CFI_MFR_AMD, 0x005F, fixup_use_secsi }, - { CFI_MFR_AMD, 0x0c01, fixup_s29gl064n_sectors }, + { CFI_MFR_AMD, S29GL064N_MN12, fixup_s29gl064n_sectors }, { CFI_MFR_AMD, 0x1301, fixup_s29gl064n_sectors }, { CFI_MFR_AMD, 0x1a00, fixup_s29gl032n_sectors }, { CFI_MFR_AMD, 0x1a01, fixup_s29gl032n_sectors },
@@ -870,7 +871,7 @@ static bool __xipram cfi_use_chip_ready_for_write(struct map_info *map) {struct cfi_private *cfi = map->fldrv_priv; -return cfi->mfr ==CFI_MFR_AMD && cfi->id ==0x0c01 ; +return cfi->mfr ==CFI_MFR_AMD && cfi->id ==S29GL064N_MN12 ; } static int __xipram chip_good_for_write(struct map_info *map,
Signature · 6 lines
2.32.0 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
Miquel Raynal
maintainerHi Tokunori,
[email protected] wrote on Thu, 17 Mar 2022 00:54:52 +0900:
Quoted 5 lines
As pointed out by this bug report [1], buffered writes are now broken on S29GL064N. This issue comes from a rework which switched from using
chip_good()tochip_ready(), because DQ true data0xFFis read on S29GL064N and an error returned bychip_good(). One way to solve the issue is to revert the change partially to usechip_readyfor S29GL064N.
Thanks for your quick iterations but overall I seriously don't feel this series is ready. At least right now I am still not satisfied by its shape.
Quoted 4 lines
[1] https://lore.kernel.org/r/[email protected]/
Fixes dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to check correct value")
... and this Fixes tag points to a v4.18 kernel, so if this is true, we should have a backport-able patch. This also means that this is not as critical than I thought if people already lived 4 years with the bug.
Vignesh, I let you continue iterating with Tokunori and ack the series when you feel it's ready.
Quoted 4 lines
Signed-off-by Tokunori Ikegami <[email protected]>Tested-by Ahmad Fatoum <[email protected]>
Quoted 9 lines
Tokunori Ikegami (3):
mtd:cfi_cmdset_0002: Move and rename
chip_check/chip_ready/chip_good_for_write
mtd:cfi_cmdset_0002: Usechip_ready()for write on S29GL064N
mtd:cfi_cmdset_0002: Add S29GL064N ID definitiondrivers/mtd/chips/cfi_cmdset_0002.c | 93 +++++++++++++++-------------- 1 file changed, 49 insertions(+), 44 deletions(-)
Thanks,
Miquèl