Skip to contentSkip to conversation

U-Boot load and run via NAND flash - ARM926EJ-S

U-Boot Thomas Jackson 4 participants 4 messages Sep 17, 2009 – Sep 18, 2009

lore
Share & tools
lore
#0 lore raw

Hi List,
I understand NOR-based flash memory devices have traditionally been used for non-volatile storage for a bootloader and other various advantages including support for execute-in-place code, random access to memory, and zero error rate, etc. However, we have a project that we would like to have U-Boot bootloader run via NAND Flash memory device on a ARM926EJ-S based board. I searched the mailing list for this and didn't see anything. I only found a question posted in 2006 where it was asked if the kernel based on ARM926EJ-S
can boot from NAND flash. Which I know is ok. Does the community know of
any existing mechanisms for this type of configuration to enable U-Boot load and run via NAND flash?

Thanks in advance!
TJ

Signature · 2 lines
View this message in context: http://www.nabble.com/U-Boot-load-and-run-via-NAND-flash---ARM926EJ-S-tp25484494p25484494.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw

I presume you system will have SDRAM and execution is from SDRAM. I did a port to an Atmel 9260 with only NAND flash (for bootstrap, bootloader, RFS). The only issue with NAND is dealing with bad blocks. There are many ways to work this. One example:
1. bootstrap - I put it in the first block as it guarantees good by manufacturer. ATmel's bootstrap will skip to next block when reading u-boot into SDRAM for execution
2. RFS - Initially I tried read/writeable FS with bad block management like JFFS2 but performance was bad. I end up using CRAMFS on top of UBI in a read only RFS partition and a small JFFS2 for RW.

Hope this helps.
Norman

Quoted 17 lines · Thomas Jackson

Hi List,
I understand NOR-based flash memory devices have traditionally been used for non-volatile storage for a bootloader and other various advantages including support for execute-in-place code, random access to memory, and zero error rate, etc. However, we have a project that we would like to have U-Boot bootloader run via NAND Flash memory device on a ARM926EJ-S based board. I searched the mailing list for this and didn't see anything. I only found a question posted in 2006 where it was asked if the kernel based on ARM926EJ-S can boot from NAND flash. Which I know is
ok. Does the community know of any existing mechanisms for this type of
configuration to enable U-Boot load and run via NAND flash?

Thanks in advance!
TJ

Signature · 2 lines
View this message in context: http://www.nabble.com/U-Boot-load-and-run-via-NAND-flash---ARM926EJ-S-tp25484494p25486169.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#2 lore raw
In reply to Thomas Jackson

Dear Thomas Jackson,

Quoted 7 lines · In message <[email protected]> you wrote:

I understand NOR-based flash memory devices have traditionally been used for non-volatile storage for a bootloader and other various advantages including support for execute-in-place code, random access to memory, and zero error rate, etc. However, we have a project that we would like to have U-Boot bootloader run via NAND Flash memory device on a ARM926EJ-S based board. I searched the mailing list for this and didn't see anything. I only found a

I have no idea how you performed that search, but it seems you have a special aptitude to avoid all the obvious hits.

Quoted 4 lines

question posted in 2006 where it was asked if the kernel based on ARM926EJ-S
can boot from NAND flash. Which I know is ok. Does the community know of
any existing mechanisms for this type of configuration to enable U-Boot load and run via NAND flash?

It's a standard feature and available on many (most?) boards that support booting from NAND. Dunno if this includes AT91 boards.

Jean-Christophe should be able to answer this, but he is currently off this planet.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Anyone can count the seeds in an apple.
No one can count the apples in a seed.
#3 lore raw
Quoted 32 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Wolfgang Denk
Sent: Thursday, September 17, 2009 1:14 PM
To: Thomas Jackson
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] U-Boot load and run via NAND flash - ARM926EJ-S

Dear Thomas Jackson,

Quoted 2 lines · In message <[email protected]> you wrote:

I understand NOR-based flash memory devices have

traditionally been used for

Quoted 1 line

non-volatile storage for a bootloader and other various

advantages including

Quoted 1 line

support for execute-in-place code, random access to memory,

and zero error

Quoted 1 line

rate, etc. However, we have a project that we would like

to have U-Boot

Quoted 1 line

bootloader run via NAND Flash memory device on a ARM926EJ-S

based board. I

Quoted 1 line

searched the mailing list for this and didn't see anything.

I only found a

I have no idea how you performed that search, but it seems you have a special aptitude to avoid all the obvious hits.

Quoted 1 line

question posted in 2006 where it was asked if the kernel

based on ARM926EJ-S

Quoted 8 lines
Quoted 1 line

can boot from NAND flash. Which I know is ok. Does the

community know of

Quoted 1 line

any existing mechanisms for this type of configuration to

enable U-Boot load

Quoted 1 line

and run via NAND flash?

It's a standard feature and available on many (most?) boards that support booting from NAND. Dunno if this includes AT91 boards.

On Kirkwood there is internal BootROM which takes care of this. In this case you need to add some header on the top of u-boot binary Pls go through doc/README.kwbimage

On Nomadik platforms there is intermediate binary sits on the very first sector which does DRAM initialization ,some other basic system setup and loads u-boot into DRAM.

I am not familiar with AT91, but there must be similar approach. May be new mkimage structure may find useful for you

Regards..

Prafulla . .

Quoted 19 lines

Jean-Christophe should be able to answer this, but he is currently off this planet.

Best regards,

Wolfgang Denk

Signature · 9 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Anyone can count the seeds in an apple.
No one can count the apples in a seed.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot