Skip to contentSkip to conversation

Allow link the it66121 display bridge driver as a lib

PATCH In review Sui Jingfeng 6 participants 64 messages Nov 14, 2023 – Nov 25, 2023

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover Allow link the it66121 display bridge driver as a lib

From: Sui Jingfeng <[email protected]>

The goal is to make this driver usuable on non-DT based systems, while without introduce duplication and preserve code sharing. The first seven patch just doing trivial cleanup, the last patch try to solve the mentioned problem by allowing static linking. Tested on a ACPI-based platform:

$ dmseg | grep drm

ACPI: bus type drm_connector registered
loongson 0000:00:06.1: [drm] dc: 264MHz, gmc: 529MHz, gpu: 529MHz loongson 0000:00:06.1: [drm] Dedicated vram start: 0xe0030000000, size: 64MiB loongson 0000:00:06.1: [drm] Loongson VBIOS version: 0.3
loongson 0000:00:06.1: [drm] Loongson VBIOS: has 8 DCBs
loongson 0000:00:06.1: [drm] VRAM: 4096 pages ready
loongson 0000:00:06.1: [drm] GTT: 32768 pages ready
loongson 0000:00:06.1: [drm] lsdc-i2c0(sda pin mask=1, scl pin mask=2) created loongson 0000:00:06.1: [drm] lsdc-i2c1(sda pin mask=4, scl pin mask=8) created loongson 0000:00:06.1: [drm] DisplayPipe-0 has DVO-0 connector i2c 1-004c: IT66121 probed, chip id: 0x4954:0x612, revision: 1 loongson 0000:00:06.1: [drm] DisplayPipe-1 has IT66121@4c attached loongson 0000:00:06.1: [drm] Total 2 outputs
loongson 0000:00:06.1: [drm] registered irq: 40
[drm] Initialized loongson 1.0.0 20220701 for 0000:00:06.1 on minor 0 loongson 0000:00:06.1: [drm] fb0: loongsondrmfb frame buffer device

Sui Jingfeng (8):
drm/bridge: it66121: Use dev replace ctx->dev in the it66121_probe() drm/bridge: it66121: Add bridge_to_it66121() helper and use it drm/bridge: it66121: Add a helper function to read bus width drm/bridge: it66121: Add a helper function to get the next bridge drm/bridge: it66121: Add a helper function to read chip id drm/bridge: it66121: Add a helper to initialize the DRM bridge
structure
drm/bridge: it66121: Add another implementation for getting match data drm/bridge: it66121: Allow link this driver as a lib

 drivers/gpu/drm/bridge/ite-it66121.c | 340 +++++++++++++++++++--------
 include/drm/bridge/ite-it66121.h     |  17 ++
 2 files changed, 258 insertions(+), 99 deletions(-)
 create mode 100644 include/drm/bridge/ite-it66121.h
Signature · 1 line
2.34.1
#1 lore raw

PATCH 1/8 drm/bridge: it66121: Use dev replace ctx->dev in the it66121_probe()

From: Sui Jingfeng <[email protected]>

As the value of 'ctx->dev' has already been cached to the local variable 'dev', so keep the usage consistent. Just trivial cleanup, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +4 -4
index 1cf3fb1f13dc..6e5c10cfa0bc 100644
@@ -1536,20 +1536,20 @@ static int it66121_probe(struct i2c_client *client)
 
 	ep = of_graph_get_remote_node(dev->of_node, 1, -1);
 	if (!ep) {
-		dev_err(ctx->dev, "The endpoint is unconnected\n");
+		dev_err(dev, "The endpoint is unconnected\n");
 		return -EINVAL;
 	}
 
 	if (!of_device_is_available(ep)) {
 		of_node_put(ep);
-		dev_err(ctx->dev, "The remote device is disabled\n");
+		dev_err(dev, "The remote device is disabled\n");
 		return -ENODEV;
 	}
 
 	ctx->next_bridge = of_drm_find_bridge(ep);
 	of_node_put(ep);
 	if (!ctx->next_bridge) {
-		dev_dbg(ctx->dev, "Next bridge not found, deferring probe\n");
+		dev_dbg(dev, "Next bridge not found, deferring probe\n");
 		return -EPROBE_DEFER;
 	}
 
@@ -1599,7 +1599,7 @@ static int it66121_probe(struct i2c_client *client)
 
 	drm_bridge_add(&ctx->bridge);
 
-	dev_info(ctx->dev, "IT66121 revision %d probed\n", revision_id);
+	dev_info(dev, "IT66121 revision %d probed\n", revision_id);
 
 	return 0;
 }
Signature · 1 line
2.34.1
Reviewed-by on v1 1/8
#2 lore raw

Re: [PATCH 1/8] drm/bridge: it66121: Use dev replace ctx->dev in the it66121_probe()

Quoted 8 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

As the value of 'ctx->dev' has already been cached to the local variable 'dev', so keep the usage consistent. Just trivial cleanup, no functional change.

Signature · 2 lines
With best wishes
Dmitry
#3 lore raw

PATCH 2/8 drm/bridge: it66121: Add bridge_to_it66121() helper and use it

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Instead of using the container_of() directly, which avoid the code lines too long in horizontial. Just trivial cleanup, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 27 ++++++++++++++++-----------
 1 file changed, 16 insertions(+), 11 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +16 -11
index 6e5c10cfa0bc..83dbdbfc9ed8 100644
@@ -315,6 +315,11 @@ struct it66121_ctx {
 	const struct it66121_chip_info *info;
 };
 
+static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
+{
+	return container_of(bridge, struct it66121_ctx, bridge);
+}
+
 static const struct regmap_range_cfg it66121_regmap_banks[] = {
 	{
 		.name = "it66121",
@@ -588,7 +593,7 @@ static bool it66121_is_hpd_detect(struct it66121_ctx *ctx)
 static int it66121_bridge_attach(struct drm_bridge *bridge,
 				 enum drm_bridge_attach_flags flags)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	int ret;
 
 	if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
@@ -699,7 +704,7 @@ static u32 *it66121_bridge_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
 						     u32 output_fmt,
 						     unsigned int *num_input_fmts)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	u32 *input_fmts;
 
 	*num_input_fmts = 0;
@@ -723,7 +728,7 @@ static u32 *it66121_bridge_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
 static void it66121_bridge_enable(struct drm_bridge *bridge,
 				  struct drm_bridge_state *bridge_state)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	struct drm_atomic_state *state = bridge_state->base.state;
 
 	ctx->connector = drm_atomic_get_new_connector_for_encoder(state, bridge->encoder);
@@ -734,7 +739,7 @@ static void it66121_bridge_enable(struct drm_bridge *bridge,
 static void it66121_bridge_disable(struct drm_bridge *bridge,
 				   struct drm_bridge_state *bridge_state)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 
 	it66121_set_mute(ctx, true);
 
@@ -746,7 +751,7 @@ static int it66121_bridge_check(struct drm_bridge *bridge,
 				struct drm_crtc_state *crtc_state,
 				struct drm_connector_state *conn_state)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 
 	if (ctx->info->id == ID_IT6610) {
 		/* The IT6610 only supports these settings */
@@ -765,7 +770,7 @@ void it66121_bridge_mode_set(struct drm_bridge *bridge,
 			     const struct drm_display_mode *adjusted_mode)
 {
 	u8 buf[HDMI_INFOFRAME_SIZE(AVI)];
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	int ret;
 
 	mutex_lock(&ctx->lock);
@@ -831,7 +836,7 @@ static enum drm_mode_status it66121_bridge_mode_valid(struct drm_bridge *bridge,
 						      const struct drm_display_info *info,
 						      const struct drm_display_mode *mode)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	unsigned long max_clock;
 
 	max_clock = (ctx->bus_width == 12) ? 74250 : 148500;
@@ -847,7 +852,7 @@ static enum drm_mode_status it66121_bridge_mode_valid(struct drm_bridge *bridge,
 
 static enum drm_connector_status it66121_bridge_detect(struct drm_bridge *bridge)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 
 	return it66121_is_hpd_detect(ctx) ? connector_status_connected
 					  : connector_status_disconnected;
@@ -855,7 +860,7 @@ static enum drm_connector_status it66121_bridge_detect(struct drm_bridge *bridge
 
 static void it66121_bridge_hpd_enable(struct drm_bridge *bridge)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	int ret;
 
 	ret = regmap_write_bits(ctx->regmap, IT66121_INT_MASK1_REG, IT66121_INT_MASK1_HPD, 0);
@@ -865,7 +870,7 @@ static void it66121_bridge_hpd_enable(struct drm_bridge *bridge)
 
 static void it66121_bridge_hpd_disable(struct drm_bridge *bridge)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	int ret;
 
 	ret = regmap_write_bits(ctx->regmap, IT66121_INT_MASK1_REG,
@@ -877,7 +882,7 @@ static void it66121_bridge_hpd_disable(struct drm_bridge *bridge)
 static struct edid *it66121_bridge_get_edid(struct drm_bridge *bridge,
 					    struct drm_connector *connector)
 {
-	struct it66121_ctx *ctx = container_of(bridge, struct it66121_ctx, bridge);
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
 	struct edid *edid;
 	int ret;
 
Signature · 1 line
2.34.1
Reviewed-by on v1 2/8
#4 lore raw

Re: [PATCH 2/8] drm/bridge: it66121: Add bridge_to_it66121() helper and use it

Quoted 7 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Instead of using the container_of() directly, which avoid the code lines too long in horizontial. Just trivial cleanup, no functional change.

Quoted 3 lines
---
 drivers/gpu/drm/bridge/ite-it66121.c | 27 ++++++++++++++++-----------
 1 file changed, 16 insertions(+), 11 deletions(-)
Signature · 2 lines
With best wishes
Dmitry
#5 lore raw

PATCH 3/8 drm/bridge: it66121: Add a helper function to read bus width

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Group those relavent code lines (which with common purpose) into one helper function, suppress the dependency on DT to function level. Just trivial cleanup, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 32 ++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +23 -9
index 83dbdbfc9ed8..0f78737adc83 100644
@@ -320,6 +320,26 @@ static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
 	return container_of(bridge, struct it66121_ctx, bridge);
 }
 
+static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width)
+{
+	struct device_node *np;
+	u32 bw;
+
+	np = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
+	if (!np)
+		return -EINVAL;
+
+	of_property_read_u32(np, "bus-width", &bw);
+	of_node_put(np);
+
+	if (bw != 12 && bw != 24)
+		return -EINVAL;
+
+	*bus_width = bw;
+
+	return 0;
+}
+
 static const struct regmap_range_cfg it66121_regmap_banks[] = {
 	{
 		.name = "it66121",
@@ -1525,19 +1545,13 @@ static int it66121_probe(struct i2c_client *client)
 	if (!ctx)
 		return -ENOMEM;
 
-	ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
-	if (!ep)
-		return -EINVAL;
-
 	ctx->dev = dev;
 	ctx->client = client;
 	ctx->info = i2c_get_match_data(client);
 
-	of_property_read_u32(ep, "bus-width", &ctx->bus_width);
-	of_node_put(ep);
-
-	if (ctx->bus_width != 12 && ctx->bus_width != 24)
-		return -EINVAL;
+	ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
+	if (ret)
+		return ret;
 
 	ep = of_graph_get_remote_node(dev->of_node, 1, -1);
 	if (!ep) {
Signature · 1 line
2.34.1
#6 lore raw

Re: [PATCH 3/8] drm/bridge: it66121: Add a helper function to read bus width

Quoted 17 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Group those relavent code lines (which with common purpose) into one helper function, suppress the dependency on DT to function level. Just trivial cleanup, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 32 ++++++++++++++++++++--------
 1 file changed, 23 insertions(+), 9 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 83dbdbfc9ed8..0f78737adc83 100644

drivers/gpu/drm/bridge/ite-it66121.c static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge) · line 323

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +1 -0
@@ -320,6 +320,26 @@ static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
        return container_of(bridge, struct it66121_ctx, bridge);
 }
 
+static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width)

Using a pointer to return int value doesn't look right. Just return a signed int here and if it is not an error, assign it to ctx->bus_width

Quoted 48 lines
drivers/gpu/drm/bridge/ite-it66121.c +22 -10
+{
+       struct device_node *np;
+       u32 bw;
+
+       np = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
+       if (!np)
+               return -EINVAL;
+
+       of_property_read_u32(np, "bus-width", &bw);
+       of_node_put(np);
+
+       if (bw != 12 && bw != 24)
+               return -EINVAL;
+
+       *bus_width = bw;
+
+       return 0;
+}
+
 static const struct regmap_range_cfg it66121_regmap_banks[] = {
        {
                .name = "it66121",
@@ -1525,19 +1545,13 @@ static int it66121_probe(struct i2c_client *client)
        if (!ctx)
                return -ENOMEM;
 
-       ep = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
-       if (!ep)
-               return -EINVAL;
-
        ctx->dev = dev;
        ctx->client = client;
        ctx->info = i2c_get_match_data(client);
 
-       of_property_read_u32(ep, "bus-width", &ctx->bus_width);
-       of_node_put(ep);
-
-       if (ctx->bus_width != 12 && ctx->bus_width != 24)
-               return -EINVAL;
+       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
+       if (ret)
+               return ret;
 
        ep = of_graph_get_remote_node(dev->of_node, 1, -1);
        if (!ep) {
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#7 lore raw

PATCH 4/8 drm/bridge: it66121: Add a helper function to get the next bridge

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Group the code lines(which with the same functional) into one dedicated function, which reduce the weight of it66121_probe() function. Just trivial cleanuo, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 53 ++++++++++++++++++----------
 1 file changed, 34 insertions(+), 19 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +34 -19
index 0f78737adc83..7e473beefc79 100644
@@ -340,6 +340,37 @@ static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width)
 	return 0;
 }
 
+static int it66121_of_get_next_bridge(struct device *dev,
+				      struct drm_bridge **next_bridge)
+{
+	struct device_node *np;
+	struct drm_bridge *bridge;
+
+	np = of_graph_get_remote_node(dev->of_node, 1, -1);
+	if (!np) {
+		dev_err(dev, "The endpoint is unconnected\n");
+		return -EINVAL;
+	}
+
+	if (!of_device_is_available(np)) {
+		of_node_put(np);
+		dev_err(dev, "The remote device is disabled\n");
+		return -ENODEV;
+	}
+
+	bridge = of_drm_find_bridge(np);
+	of_node_put(np);
+
+	if (!bridge) {
+		dev_dbg(dev, "Next bridge not found, deferring probe\n");
+		return -EPROBE_DEFER;
+	}
+
+	*next_bridge = bridge;
+
+	return 0;
+}
+
 static const struct regmap_range_cfg it66121_regmap_banks[] = {
 	{
 		.name = "it66121",
@@ -1531,7 +1562,6 @@ static const char * const it66121_supplies[] = {
 static int it66121_probe(struct i2c_client *client)
 {
 	u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
-	struct device_node *ep;
 	int ret;
 	struct it66121_ctx *ctx;
 	struct device *dev = &client->dev;
@@ -1553,24 +1583,9 @@ static int it66121_probe(struct i2c_client *client)
 	if (ret)
 		return ret;
 
-	ep = of_graph_get_remote_node(dev->of_node, 1, -1);
-	if (!ep) {
-		dev_err(dev, "The endpoint is unconnected\n");
-		return -EINVAL;
-	}
-
-	if (!of_device_is_available(ep)) {
-		of_node_put(ep);
-		dev_err(dev, "The remote device is disabled\n");
-		return -ENODEV;
-	}
-
-	ctx->next_bridge = of_drm_find_bridge(ep);
-	of_node_put(ep);
-	if (!ctx->next_bridge) {
-		dev_dbg(dev, "Next bridge not found, deferring probe\n");
-		return -EPROBE_DEFER;
-	}
+	ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+	if (ret)
+		return ret;
 
 	i2c_set_clientdata(client, ctx);
 	mutex_init(&ctx->lock);
Signature · 1 line
2.34.1
#8 lore raw

Re: [PATCH 4/8] drm/bridge: it66121: Add a helper function to get the next bridge

Quoted 17 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Group the code lines(which with the same functional) into one dedicated function, which reduce the weight of it66121_probe() function. Just trivial cleanuo, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 53 ++++++++++++++++++----------
 1 file changed, 34 insertions(+), 19 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 0f78737adc83..7e473beefc79 100644

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width) · line 344

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -0
@@ -340,6 +340,37 @@ static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width)
        return 0;
 }
 
+static int it66121_of_get_next_bridge(struct device *dev,
+                                     struct drm_bridge **next_bridge)

it already exists and it is called drm_of_find_panel_or_bridge(), could you please use it instead?

Quoted 71 lines
drivers/gpu/drm/bridge/ite-it66121.c +32 -20
+{
+       struct device_node *np;
+       struct drm_bridge *bridge;
+
+       np = of_graph_get_remote_node(dev->of_node, 1, -1);
+       if (!np) {
+               dev_err(dev, "The endpoint is unconnected\n");
+               return -EINVAL;
+       }
+
+       if (!of_device_is_available(np)) {
+               of_node_put(np);
+               dev_err(dev, "The remote device is disabled\n");
+               return -ENODEV;
+       }
+
+       bridge = of_drm_find_bridge(np);
+       of_node_put(np);
+
+       if (!bridge) {
+               dev_dbg(dev, "Next bridge not found, deferring probe\n");
+               return -EPROBE_DEFER;
+       }
+
+       *next_bridge = bridge;
+
+       return 0;
+}
+
 static const struct regmap_range_cfg it66121_regmap_banks[] = {
        {
                .name = "it66121",
@@ -1531,7 +1562,6 @@ static const char * const it66121_supplies[] = {
 static int it66121_probe(struct i2c_client *client)
 {
        u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
-       struct device_node *ep;
        int ret;
        struct it66121_ctx *ctx;
        struct device *dev = &client->dev;
@@ -1553,24 +1583,9 @@ static int it66121_probe(struct i2c_client *client)
        if (ret)
                return ret;
 
-       ep = of_graph_get_remote_node(dev->of_node, 1, -1);
-       if (!ep) {
-               dev_err(dev, "The endpoint is unconnected\n");
-               return -EINVAL;
-       }
-
-       if (!of_device_is_available(ep)) {
-               of_node_put(ep);
-               dev_err(dev, "The remote device is disabled\n");
-               return -ENODEV;
-       }
-
-       ctx->next_bridge = of_drm_find_bridge(ep);
-       of_node_put(ep);
-       if (!ctx->next_bridge) {
-               dev_dbg(dev, "Next bridge not found, deferring probe\n");
-               return -EPROBE_DEFER;
-       }
+       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+       if (ret)
+               return ret;
 
        i2c_set_clientdata(client, ctx);
        mutex_init(&ctx->lock);
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#9 lore raw

Re: [PATCH 4/8] drm/bridge: it66121: Add a helper function to get the next bridge

Hi,

Quoted 20 lines · Dmitry Baryshkov
Quoted 19 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Group the code lines(which with the same functional) into one dedicated function, which reduce the weight of it66121_probe() function. Just trivial cleanuo, no functional change.

---
  drivers/gpu/drm/bridge/ite-it66121.c | 53 ++++++++++++++++++----------
  1 file changed, 34 insertions(+), 19 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 0f78737adc83..7e473beefc79 100644
@@ -340,6 +340,37 @@ static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width)
         return 0;
  }
 
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width) · line 344

Quoted 2 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -0
+static int it66121_of_get_next_bridge(struct device *dev,
+                                     struct drm_bridge **next_bridge)

it already exists and it is called drm_of_find_panel_or_bridge(), could you please use it instead?

That function is too fat and tangled, and should be untangled. it66121 can not connect with a panel, this is a prior knowledge and is known at compile time. So this prior knowledge shouldn't be dropped.

Quoted 72 lines
Quoted 71 lines
drivers/gpu/drm/bridge/ite-it66121.c +32 -20
+{
+       struct device_node *np;
+       struct drm_bridge *bridge;
+
+       np = of_graph_get_remote_node(dev->of_node, 1, -1);
+       if (!np) {
+               dev_err(dev, "The endpoint is unconnected\n");
+               return -EINVAL;
+       }
+
+       if (!of_device_is_available(np)) {
+               of_node_put(np);
+               dev_err(dev, "The remote device is disabled\n");
+               return -ENODEV;
+       }
+
+       bridge = of_drm_find_bridge(np);
+       of_node_put(np);
+
+       if (!bridge) {
+               dev_dbg(dev, "Next bridge not found, deferring probe\n");
+               return -EPROBE_DEFER;
+       }
+
+       *next_bridge = bridge;
+
+       return 0;
+}
+
  static const struct regmap_range_cfg it66121_regmap_banks[] = {
         {
                 .name = "it66121",
@@ -1531,7 +1562,6 @@ static const char * const it66121_supplies[] = {
  static int it66121_probe(struct i2c_client *client)
  {
         u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
-       struct device_node *ep;
         int ret;
         struct it66121_ctx *ctx;
         struct device *dev = &client->dev;
@@ -1553,24 +1583,9 @@ static int it66121_probe(struct i2c_client *client)
         if (ret)
                 return ret;
 
-       ep = of_graph_get_remote_node(dev->of_node, 1, -1);
-       if (!ep) {
-               dev_err(dev, "The endpoint is unconnected\n");
-               return -EINVAL;
-       }
-
-       if (!of_device_is_available(ep)) {
-               of_node_put(ep);
-               dev_err(dev, "The remote device is disabled\n");
-               return -ENODEV;
-       }
-
-       ctx->next_bridge = of_drm_find_bridge(ep);
-       of_node_put(ep);
-       if (!ctx->next_bridge) {
-               dev_dbg(dev, "Next bridge not found, deferring probe\n");
-               return -EPROBE_DEFER;
-       }
+       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+       if (ret)
+               return ret;
 
         i2c_set_clientdata(client, ctx);
         mutex_init(&ctx->lock);
--

2.34.1

#10 lore raw

Re: [PATCH 4/8] drm/bridge: it66121: Add a helper function to get the next bridge

Quoted 30 lines · Sui Jingfeng

Hi,

Quoted 20 lines · Dmitry Baryshkov
Quoted 19 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Group the code lines(which with the same functional) into one dedicated function, which reduce the weight of it66121_probe() function. Just trivial cleanuo, no functional change.

---
  drivers/gpu/drm/bridge/ite-it66121.c | 53 ++++++++++++++++++----------
  1 file changed, 34 insertions(+), 19 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 0f78737adc83..7e473beefc79 100644
@@ -340,6 +340,37 @@ static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width)
         return 0;
  }
 
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_of_read_bus_width(struct device *dev, u32 *bus_width) · line 344

Quoted 2 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -0
+static int it66121_of_get_next_bridge(struct device *dev,
+                                     struct drm_bridge **next_bridge)

it already exists and it is called drm_of_find_panel_or_bridge(), could you please use it instead?

Quoted 4 lines

That function is too fat and tangled, and should be untangled. it66121 can not connect with a panel, this is a prior knowledge and is known at compile time. So this prior knowledge shouldn't be dropped.

This prior knowledge is kept by passing NULL as a panel. We already have a helper. It covers your use case. There is no need to write your own boilerplate code for it.

Quoted 73 lines
Quoted 73 lines
Quoted 72 lines
drivers/gpu/drm/bridge/ite-it66121.c +32 -20
+{
+       struct device_node *np;
+       struct drm_bridge *bridge;
+
+       np = of_graph_get_remote_node(dev->of_node, 1, -1);
+       if (!np) {
+               dev_err(dev, "The endpoint is unconnected\n");
+               return -EINVAL;
+       }
+
+       if (!of_device_is_available(np)) {
+               of_node_put(np);
+               dev_err(dev, "The remote device is disabled\n");
+               return -ENODEV;
+       }
+
+       bridge = of_drm_find_bridge(np);
+       of_node_put(np);
+
+       if (!bridge) {
+               dev_dbg(dev, "Next bridge not found, deferring probe\n");
+               return -EPROBE_DEFER;
+       }
+
+       *next_bridge = bridge;
+
+       return 0;
+}
+
  static const struct regmap_range_cfg it66121_regmap_banks[] = {
         {
                 .name = "it66121",
@@ -1531,7 +1562,6 @@ static const char * const it66121_supplies[] = {
  static int it66121_probe(struct i2c_client *client)
  {
         u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
-       struct device_node *ep;
         int ret;
         struct it66121_ctx *ctx;
         struct device *dev = &client->dev;
@@ -1553,24 +1583,9 @@ static int it66121_probe(struct i2c_client *client)
         if (ret)
                 return ret;
 
-       ep = of_graph_get_remote_node(dev->of_node, 1, -1);
-       if (!ep) {
-               dev_err(dev, "The endpoint is unconnected\n");
-               return -EINVAL;
-       }
-
-       if (!of_device_is_available(ep)) {
-               of_node_put(ep);
-               dev_err(dev, "The remote device is disabled\n");
-               return -ENODEV;
-       }
-
-       ctx->next_bridge = of_drm_find_bridge(ep);
-       of_node_put(ep);
-       if (!ctx->next_bridge) {
-               dev_dbg(dev, "Next bridge not found, deferring probe\n");
-               return -EPROBE_DEFER;
-       }
+       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+       if (ret)
+               return ret;
 
         i2c_set_clientdata(client, ctx);
         mutex_init(&ctx->lock);
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#11 lore raw

PATCH 5/8 drm/bridge: it66121: Add a helper function to read chip id

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
 1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +34 -13
index 7e473beefc79..f36d05331f25 100644
@@ -313,6 +313,9 @@ struct it66121_ctx {
 		bool auto_cts;
 	} audio;
 	const struct it66121_chip_info *info;
+	u16 vender_id;
+	u16 device_id;
+	u8 revision;
 };
 
 static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
 	gpiod_set_value(ctx->gpio_reset, 0);
 }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+	u8 id[4];
+	int ret;
+
+	ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+	if (ret < 0) {
+		dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+		return ret;
+	}
+
+	ctx->vender_id = (u16)id[1] << 8 | id[0];
+	ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+	/* Revision is shared with DEVICE_ID1 */
+	ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+	if (verbose) {
+		dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+			 ctx->vender_id, ctx->device_id, ctx->revision);
+	}
+
+	return 0;
+}
+
 static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
 {
 	return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
 static int it66121_probe(struct i2c_client *client)
 {
-	u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
 	int ret;
 	struct it66121_ctx *ctx;
 	struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
 	if (IS_ERR(ctx->regmap))
 		return PTR_ERR(ctx->regmap);
 
-	regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-	regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-	regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-	regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-	/* Revision is shared with DEVICE_ID1 */
-	revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-	device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+	ret = it66121_read_chip_id(ctx, false);
+	if (ret)
+		return ret;
 
-	if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-	    (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+	if (ctx->vender_id != ctx->info->vid ||
+	    ctx->device_id != ctx->info->pid)
 		return -ENODEV;
-	}
 
 	ctx->bridge.funcs = &it66121_bridge_funcs;
 	ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
 	drm_bridge_add(&ctx->bridge);
 
-	dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+	dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+		 ctx->vender_id, ctx->device_id, ctx->revision);
 
 	return 0;
 }
Signature · 1 line
2.34.1
#12 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Quoted 17 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
 1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                bool auto_cts;
        } audio;
        const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 80 lines
drivers/gpu/drm/bridge/ite-it66121.c +31 -14
 };
 
 static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
        gpiod_set_value(ctx->gpio_reset, 0);
 }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
 static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
 {
        return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
 static int it66121_probe(struct i2c_client *client)
 {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
        int ret;
        struct it66121_ctx *ctx;
        struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
        if (IS_ERR(ctx->regmap))
                return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)
                return -ENODEV;
-       }
 
        ctx->bridge.funcs = &it66121_bridge_funcs;
        ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
        drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
        return 0;
 }
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#13 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
  drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
  1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                 bool auto_cts;
         } audio;
         const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
  };
 
  static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
         gpiod_set_value(ctx->gpio_reset, 0);
  }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
  static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
  {
         return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
  static int it66121_probe(struct i2c_client *client)
  {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
         int ret;
         struct it66121_ctx *ctx;
         struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
         if (IS_ERR(ctx->regmap))
                 return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

Quoted 19 lines
Quoted 18 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                 return -ENODEV;
-       }
 
         ctx->bridge.funcs = &it66121_bridge_funcs;
         ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
         drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
         return 0;
  }
--

2.34.1

#14 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Quoted 88 lines · Sui Jingfeng

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
  drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
  1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                 bool auto_cts;
         } audio;
         const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
  };
 
  static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
         gpiod_set_value(ctx->gpio_reset, 0);
  }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
  static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
  {
         return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
  static int it66121_probe(struct i2c_client *client)
  {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
         int ret;
         struct it66121_ctx *ctx;
         struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
         if (IS_ERR(ctx->regmap))
                 return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 8 lines
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

And the patch 7 will be changed once you have proper i2c client struct registered.

Quoted 4 lines

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

I'd say, there is little point in whoami debugfs files. Debugfs is for the useful information.

Quoted 21 lines
Quoted 21 lines
Quoted 20 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                 return -ENODEV;
-       }
 
         ctx->bridge.funcs = &it66121_bridge_funcs;
         ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
         drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
         return 0;
  }
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#15 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Hi,

Quoted 94 lines · Dmitry Baryshkov
Quoted 93 lines · Sui Jingfeng

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
   drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
   1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                  bool auto_cts;
          } audio;
          const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
   };
 
   static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
          gpiod_set_value(ctx->gpio_reset, 0);
   }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
   static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
   {
          return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
   static int it66121_probe(struct i2c_client *client)
   {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
          int ret;
          struct it66121_ctx *ctx;
          struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
          if (IS_ERR(ctx->regmap))
                  return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

Quoted 4 lines
Quoted 1 line

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

And the patch 7 will be changed once you have proper i2c client struct registered.

We will create a "wrong"i2c client intentionally by calling i2c_new_client_device, the "wrong" here means that 'board_info.type' is not equal to "it66121" or "it6610".

I probably know what you means, but please note that we are not object you at here.
The reason why we prefer theit66121_get_match_data() over the i2c_get_match_data() is that our it66121_get_match_data() works with *the least dependency*. Ourversion don't rely on the DT to provide compatible strings. Because the it66121 itself already
provided constant hard-coded vender id and device id on-chip register. This is a bit
similar with the PCIe devices. This chip id speak everything about chip identify.
By re-arranging the variants into array, searching and matching against became
straight-forward. We can also utilize the vender id and device id information to
dynamic bind the instance specific functions *at the setup(probe) time*. Which helps
to untangle the it66121 and it6610 cases with function object. Currently they are
tangled. This is not a problem simply because the model supported is too small(less).

Quoted 27 lines
Quoted 3 lines

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

I'd say, there is little point in whoami debugfs files. Debugfs is for the useful information.

Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                  return -ENODEV;
-       }
 
          ctx->bridge.funcs = &it66121_bridge_funcs;
          ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
          drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
          return 0;
   }
--

2.34.1

#16 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Quoted 106 lines · Sui Jingfeng

Hi,

Quoted 94 lines · Dmitry Baryshkov
Quoted 93 lines · Sui Jingfeng

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
   drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
   1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                  bool auto_cts;
          } audio;
          const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
   };
 
   static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
          gpiod_set_value(ctx->gpio_reset, 0);
   }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
   static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
   {
          return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
   static int it66121_probe(struct i2c_client *client)
   {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
          int ret;
          struct it66121_ctx *ctx;
          struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
          if (IS_ERR(ctx->regmap))
                  return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

Quoted 4 lines
Quoted 1 line

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

And the patch 7 will be changed once you have proper i2c client struct registered.

We will create a "wrong"i2c client intentionally by calling i2c_new_client_device, the "wrong" here means that 'board_info.type' is not equal to "it66121" or "it6610".

Quoted 11 lines

I probably know what you means, but please note that we are not object you at here. The reason why we prefer theit66121_get_match_data() over the i2c_get_match_data() is that our it66121_get_match_data() works with *the least dependency*. Ourversion
don't rely on the DT to provide compatible strings. Because the it66121 itself already provided constant hard-coded vender id and device id on-chip register. This is a bit similar with the PCIe devices. This chip id speak everything about chip identify. By re-arranging the variants into array, searching and matching against became straight-forward. We can also utilize the vender id and device id information to dynamic bind the instance specific functions *at the setup(probe) time*. Which helps to untangle the it66121 and it6610 cases with function object. Currently they are tangled. This is not a problem simply because the model supported is too small(less).

The difference is that PCI or USB are discoverable buses, but I2C and SPI are not.
The kernel tends to use generic mechanisms if possible. And for the I2C / SPI buses the generic mechanism is match data.
What you are doing is nice if there was just the it66121 driver. However there is more than that. Many more drivers. And the generic approach becomes important, as it helps other developers to work with better efficiency.

Quoted 26 lines
Quoted 26 lines
Quoted 2 lines

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

I'd say, there is little point in whoami debugfs files. Debugfs is for the useful information.

Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                  return -ENODEV;
-       }
 
          ctx->bridge.funcs = &it66121_bridge_funcs;
          ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
          drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
          return 0;
   }
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#17 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

In reply to Dmitry Baryshkov

Hi,

Quoted 95 lines · Dmitry Baryshkov
Quoted 87 lines · Sui Jingfeng

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
   drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
   1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                  bool auto_cts;
          } audio;
          const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
   };
 
   static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
          gpiod_set_value(ctx->gpio_reset, 0);
   }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
   static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
   {
          return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
   static int it66121_probe(struct i2c_client *client)
   {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
          int ret;
          struct it66121_ctx *ctx;
          struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
          if (IS_ERR(ctx->regmap))
                  return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 7 lines
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

Quoted 8 lines

And the patch 7 will be changed once you have proper i2c client struct registered.

Quoted 3 lines

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

I'd say, there is little point in whoami debugfs files. Debugfs is for the useful information.

Sinceit6610 was introduced, how do you know what the device it66121 driver is binding? Printing model specific information is common practice for a large driver. Especially if you can only able to debug remotely where only a SSH is given. You could see debugfs of drm/etnaviv for a reference. It is common to testing a large driver running on 20+ machines with various hardware model.

Quoted 21 lines
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                  return -ENODEV;
-       }
 
          ctx->bridge.funcs = &it66121_bridge_funcs;
          ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
          drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
          return 0;
   }
--

2.34.1

#18 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Quoted 106 lines · Sui Jingfeng

Hi,

Quoted 101 lines · Dmitry Baryshkov
Quoted 87 lines · Sui Jingfeng

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
   drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
   1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                  bool auto_cts;
          } audio;
          const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
   };
 
   static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
          gpiod_set_value(ctx->gpio_reset, 0);
   }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
   static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
   {
          return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
   static int it66121_probe(struct i2c_client *client)
   {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
          int ret;
          struct it66121_ctx *ctx;
          struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
          if (IS_ERR(ctx->regmap))
                  return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 7 lines
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

And the patch 7 will be changed once you have proper i2c client struct registered.

Quoted 3 lines

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

Quoted 7 lines
Quoted 2 lines

I'd say, there is little point in whoami debugfs files. Debugfs is for the useful information.

Sinceit6610 was introduced, how do you know what the device it66121 driver is binding? Printing model specific information is common practice for a large driver. Especially if you can only able to debug remotely where only a SSH is given.

cat /sys/bus/i2c/devices/.../name

Quoted 26 lines

You could see debugfs of drm/etnaviv for a
reference. It is common to testing a large driver running on 20+ machines with various hardware model.

Quoted 21 lines
Quoted 19 lines
Quoted 19 lines
Quoted 19 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                  return -ENODEV;
-       }
 
          ctx->bridge.funcs = &it66121_bridge_funcs;
          ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
          drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
          return 0;
   }
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#19 lore raw

Re: [PATCH 5/8] drm/bridge: it66121: Add a helper function to read chip id

Hi,

Quoted 105 lines · Dmitry Baryshkov
Quoted 104 lines · Sui Jingfeng

Hi,

Quoted 100 lines · Dmitry Baryshkov
Quoted 87 lines · Sui Jingfeng

Hi,

Quoted 83 lines · Dmitry Baryshkov
Quoted 16 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Read the required chip id data back by calling regmap_bulk_read() once, reduce the number of local variables needed in it66121_probe() function. And store its values into struct it66121_ctx, as it will be used latter.

---
    drivers/gpu/drm/bridge/ite-it66121.c | 47 ++++++++++++++++++++--------
    1 file changed, 34 insertions(+), 13 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index 7e473beefc79..f36d05331f25 100644

drivers/gpu/drm/bridge/ite-it66121.c struct it66121_ctx { · line 318

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -313,6 +313,9 @@ struct it66121_ctx {
                   bool auto_cts;
           } audio;
           const struct it66121_chip_info *info;
+       u16 vender_id;
+       u16 device_id;
+       u8 revision;

There is no need to store them, they are not used by the driver anywhere.

Quoted 58 lines
drivers/gpu/drm/bridge/ite-it66121.c +27 -9
    };
 
    static inline struct it66121_ctx *bridge_to_it66121(struct drm_bridge *bridge)
@@ -399,6 +402,30 @@ static void it66121_hw_reset(struct it66121_ctx *ctx)
           gpiod_set_value(ctx->gpio_reset, 0);
    }
 
+static int it66121_read_chip_id(struct it66121_ctx *ctx, bool verbose)
+{
+       u8 id[4];
+       int ret;
+
+       ret = regmap_bulk_read(ctx->regmap, IT66121_VENDOR_ID0_REG, id, 4);
+       if (ret < 0) {
+               dev_err(ctx->dev, "Failed to read chip ID: %d\n", ret);
+               return ret;
+       }
+
+       ctx->vender_id = (u16)id[1] << 8 | id[0];
+       ctx->device_id = ((u16)(id[3] & IT66121_DEVICE_ID1_MASK) << 8 | id[2]);
+       /* Revision is shared with DEVICE_ID1 */
+       ctx->revision = FIELD_GET(IT66121_REVISION_MASK, id[3]);
+
+       if (verbose) {
+               dev_info(ctx->dev, "Found ITE66121: 0x%x%x, revision: %u\n",
+                        ctx->vender_id, ctx->device_id, ctx->revision);
+       }
+
+       return 0;
+}
+
    static inline int it66121_preamble_ddc(struct it66121_ctx *ctx)
    {
           return regmap_write(ctx->regmap, IT66121_MASTER_SEL_REG, IT66121_MASTER_SEL_HOST);
@@ -1561,7 +1588,6 @@ static const char * const it66121_supplies[] = {
 
    static int it66121_probe(struct i2c_client *client)
    {
-       u32 revision_id, vendor_ids[2] = { 0 }, device_ids[2] = { 0 };
           int ret;
           struct it66121_ctx *ctx;
           struct device *dev = &client->dev;
@@ -1603,19 +1629,13 @@ static int it66121_probe(struct i2c_client *client)
           if (IS_ERR(ctx->regmap))
                   return PTR_ERR(ctx->regmap);
 
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID0_REG, &vendor_ids[0]);
-       regmap_read(ctx->regmap, IT66121_VENDOR_ID1_REG, &vendor_ids[1]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID0_REG, &device_ids[0]);
-       regmap_read(ctx->regmap, IT66121_DEVICE_ID1_REG, &device_ids[1]);
-
-       /* Revision is shared with DEVICE_ID1 */
-       revision_id = FIELD_GET(IT66121_REVISION_MASK, device_ids[1]);
-       device_ids[1] &= IT66121_DEVICE_ID1_MASK;
+       ret = it66121_read_chip_id(ctx, false);
+       if (ret)
+               return ret;
 
Quoted 7 lines
Quoted 4 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1637

Quoted 4 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -2
-       if ((vendor_ids[1] << 8 | vendor_ids[0]) != ctx->info->vid ||
-           (device_ids[1] << 8 | device_ids[0]) != ctx->info->pid) {
+       if (ctx->vender_id != ctx->info->vid ||
+           ctx->device_id != ctx->info->pid)

Q: There is no need to store them, they are not used by the driver anywhere.

A: Here it is used, it is also used by the 0007-patch to get the entity(instance)-specific data.

And the patch 7 will be changed once you have proper i2c client struct registered.

Quoted 2 lines

Since it6610 was introduced, this is used for chip identifying. It can also be used with in debugfs context, to show who I am.

Quoted 7 lines
Quoted 6 lines
Quoted 2 lines

I'd say, there is little point in whoami debugfs files. Debugfs is for the useful information.

Sinceit6610 was introduced, how do you know what the device it66121 driver is binding? Printing model specific information is common practice for a large driver. Especially if you can only able to debug remotely where only a SSH is given.

cat /sys/bus/i2c/devices/.../name

No, this is not enough. This is also not straight-forward. Because the system will have multiple i2c device. This is a bit hard to find which one is corresponding to the it66121.

This is needed during the development and debug phase.
We will also want to know the vendor id, device id and revision id. As those chip id are constant values, matching those chip id against the values in datasheet is a kind of sanity test. Which helps us to know if the i2c regmap(the communication channel) has been setup successfully or not.

Quoted 26 lines
Quoted 24 lines

You could see debugfs of drm/etnaviv for a
reference. It is common to testing a large driver running on 20+ machines with various hardware model.

Quoted 19 lines
Quoted 18 lines
Quoted 18 lines
Quoted 18 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
                   return -ENODEV;
-       }
 
           ctx->bridge.funcs = &it66121_bridge_funcs;
           ctx->bridge.of_node = dev->of_node;
@@ -1633,7 +1653,8 @@ static int it66121_probe(struct i2c_client *client)
 
           drm_bridge_add(&ctx->bridge);
 
-       dev_info(dev, "IT66121 revision %d probed\n", revision_id);
+       dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
+                ctx->vender_id, ctx->device_id, ctx->revision);
 
           return 0;
    }
--

2.34.1

#20 lore raw

PATCH 6/8 drm/bridge: it66121: Add a helper to initialize the DRM bridge structure

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Helps the it66121_probe() function to reduce weight, no functional change.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +17 -7
index f36d05331f25..2f7f00f1bedb 100644
@@ -1004,6 +1004,21 @@ static const struct drm_bridge_funcs it66121_bridge_funcs = {
 	.hpd_disable = it66121_bridge_hpd_disable,
 };
 
+static void it66121_bridge_init_base(struct drm_bridge *bridge,
+				     struct device_node *of_node,
+				     bool hpd_support)
+{
+	bridge->funcs = &it66121_bridge_funcs;
+	bridge->type = DRM_MODE_CONNECTOR_HDMIA;
+	bridge->ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID;
+	if (hpd_support)
+		bridge->ops |= DRM_BRIDGE_OP_HPD;
+
+	bridge->of_node = of_node;
+
+	drm_bridge_add(bridge);
+}
+
 static irqreturn_t it66121_irq_threaded_handler(int irq, void *dev_id)
 {
 	int ret;
@@ -1637,11 +1652,6 @@ static int it66121_probe(struct i2c_client *client)
 	    ctx->device_id != ctx->info->pid)
 		return -ENODEV;
 
-	ctx->bridge.funcs = &it66121_bridge_funcs;
-	ctx->bridge.of_node = dev->of_node;
-	ctx->bridge.type = DRM_MODE_CONNECTOR_HDMIA;
-	ctx->bridge.ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD;
-
 	ret = devm_request_threaded_irq(dev, client->irq, NULL,	it66121_irq_threaded_handler,
 					IRQF_ONESHOT, dev_name(dev), ctx);
 	if (ret < 0) {
@@ -1649,9 +1659,9 @@ static int it66121_probe(struct i2c_client *client)
 		return ret;
 	}
 
-	it66121_audio_codec_init(ctx, dev);
+	it66121_bridge_init_base(&ctx->bridge, dev->of_node, true);
 
-	drm_bridge_add(&ctx->bridge);
+	it66121_audio_codec_init(ctx, dev);
 
 	dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
 		 ctx->vender_id, ctx->device_id, ctx->revision);
Signature · 1 line
2.34.1
#21 lore raw

Re: [PATCH 6/8] drm/bridge: it66121: Add a helper to initialize the DRM bridge structure

Quoted 4 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Helps the it66121_probe() function to reduce weight, no functional change.

This is not a proper commit message.

Quoted 11 lines
---
 drivers/gpu/drm/bridge/ite-it66121.c | 24 +++++++++++++++++-------
 1 file changed, 17 insertions(+), 7 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +0 -0
index f36d05331f25..2f7f00f1bedb 100644

drivers/gpu/drm/bridge/ite-it66121.c static const struct drm_bridge_funcs it66121_bridge_funcs = { · line 1009

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
@@ -1004,6 +1004,21 @@ static const struct drm_bridge_funcs it66121_bridge_funcs = {
        .hpd_disable = it66121_bridge_hpd_disable,
 };
 
+static void it66121_bridge_init_base(struct drm_bridge *bridge,
+                                    struct device_node *of_node,
+                                    bool hpd_support)

At this point there is no reason for the bridge to miss HPD support.

Quoted 42 lines
drivers/gpu/drm/bridge/ite-it66121.c +14 -8
+{
+       bridge->funcs = &it66121_bridge_funcs;
+       bridge->type = DRM_MODE_CONNECTOR_HDMIA;
+       bridge->ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID;
+       if (hpd_support)
+               bridge->ops |= DRM_BRIDGE_OP_HPD;
+
+       bridge->of_node = of_node;
+
+       drm_bridge_add(bridge);
+}
+
 static irqreturn_t it66121_irq_threaded_handler(int irq, void *dev_id)
 {
        int ret;
@@ -1637,11 +1652,6 @@ static int it66121_probe(struct i2c_client *client)
            ctx->device_id != ctx->info->pid)
                return -ENODEV;
 
-       ctx->bridge.funcs = &it66121_bridge_funcs;
-       ctx->bridge.of_node = dev->of_node;
-       ctx->bridge.type = DRM_MODE_CONNECTOR_HDMIA;
-       ctx->bridge.ops = DRM_BRIDGE_OP_DETECT | DRM_BRIDGE_OP_EDID | DRM_BRIDGE_OP_HPD;
-
        ret = devm_request_threaded_irq(dev, client->irq, NULL, it66121_irq_threaded_handler,
                                        IRQF_ONESHOT, dev_name(dev), ctx);
        if (ret < 0) {
@@ -1649,9 +1659,9 @@ static int it66121_probe(struct i2c_client *client)
                return ret;
        }
 
-       it66121_audio_codec_init(ctx, dev);
+       it66121_bridge_init_base(&ctx->bridge, dev->of_node, true);
 
-       drm_bridge_add(&ctx->bridge);
+       it66121_audio_codec_init(ctx, dev);
 
        dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
                 ctx->vender_id, ctx->device_id, ctx->revision);
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#22 lore raw

PATCH 7/8 drm/bridge: it66121: Add another implementation for getting match data

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Because if use the i2c_get_match_data() function on our platform, the following error will emerge.

[    3.597872] ACPI: bus type drm_connector registered
[    3.602877] loongson 0000:00:06.1: Found LS7A1000 bridge chipset, revision: 1
[    3.610013] loongson 0000:00:06.1: [drm] dc: 264MHz, gmc: 529MHz, gpu: 529MHz
[    3.617111] loongson 0000:00:06.1: [drm] Dedicated vram start: 0xe0030000000, size: 64MiB
[    3.633628] loongson 0000:00:06.1: [drm] Loongson VBIOS version: 0.3
[    3.639944] loongson 0000:00:06.1: [drm] Loongson VBIOS: has 8 DCBs
[    3.646271] Console: switching to colour dummy device 80x25
[    3.651902] loongson 0000:00:06.1: [drm] VRAM: 4096 pages ready
[    3.657791] loongson 0000:00:06.1: [drm] GTT: 32768 pages ready
[    3.663731] loongson 0000:00:06.1: [drm] lsdc-i2c0(sda pin mask=1, scl pin mask=2) created
[    3.671966] loongson 0000:00:06.1: [drm] lsdc-i2c1(sda pin mask=4, scl pin mask=8) created
[    3.680188] loongson 0000:00:06.1: [drm] DisplayPipe-0 has DVO-0 connector
[    3.711860] debugfs: Directory '1-004c' with parent 'regmap' already present!
[    3.720312] CPU 0 Unable to handle kernel paging request at virtual address 0000000000000090, era == 9000000002faffec, ra == 9000000002faffc8
[    3.732935] Oops[#1]:
[    3.735187] CPU: 0 PID: 8 Comm: kworker/0:0 Not tainted 6.6.0-rc3+ #941
[    3.741757] Hardware name: Loongson Loongson-3A5000-7A1000-1w-ML5A/Loongson-LS3A5000-7A1000-1w-ML5A, BIOS vUDK2018-LoongArch-V4.0.05-test-stable202305 06/
[    3.755500] Workqueue: events work_for_cpu_fn
[    3.759833] pc 9000000002faffec ra 9000000002faffc8 tp 900000010017c000 sp 900000010017fb80
[    3.768132] a0 0000000000000000 a1 9000000101c00420 a2 0000000000000001 a3 900000010017fbc0
[    3.776430] a4 0000000000000004 a5 0000000000000000 a6 0000000000000001 a7 0000000000000001
[    3.784727] t0 0000000000000000 t1 0000000000000001 t2 0000000006124954 t3 0000000000000012
[    3.793026] t4 0000000000004954 t5 900000000800b530 t6 0000000000000000 t7 0000000000018500
[    3.801324] t8 90000001019c90c0 u0 9000000101c00c00 s9 fffffffffffff000 s0 9000000101c00400
[    3.809621] s1 0000000000000000 s2 0000000000000000 s3 9000000003c42cb0 s4 9000000101c00420
[    3.817920] s5 900000010017fc48 s6 0000000000000000 s7 0000000000000000 s8 90000000037fa000
[    3.826219]    ra: 9000000002faffc8 i2c_get_match_data+0x24/0xac
[    3.832189]   ERA: 9000000002faffec i2c_get_match_data+0x48/0xac
[    3.838156]  CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[    3.844303]  PRMD: 00000004 (PPLV0 +PIE -PWE)
[    3.848631]  EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
[    3.853391]  ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
[    3.858149] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[    3.863599]  BADV: 0000000000000090
[    3.867058]  PRID: 0014c011 (Loongson-64bit, Loongson-3A5000)
[    3.872764] Modules linked in:
[    3.875793] Process kworker/0:0 (pid: 8, threadinfo=(____ptrval____), task=(____ptrval____))
[    3.884180] Stack : 9000000101c00400 0000000000000000 900000010177f428 9000000002ceb734
[    3.892137]         9000000101c00404 90000000037fa000 900000010017fc60 9000000101c00400
[    3.900093]         9000000016124954 8c326e68047d36df 0000004c037fa000 900000010017fc50
[    3.908050]         0000000000000080 9000000003c44490 900000010017fcb0 90000001003e9ec0
[    3.916007]         0000000000000001 900000010044f000 900000010017fc60 9000000101c00400
[    3.923964]         90000000037fa000 9000000002cf05a8 90000001003e8000 900000010017fcb2
[    3.931920]         000000304c17fc68 0000000000000000 000000000000004c 0000000000000000
[    3.939877]         4031323136365449 0000000000006334 004c000000000000 0000000000000000
[    3.947833]         0000000000000000 0000000000000000 0000000000000000 0000000000000000
[    3.955790]         0000000000000000 0000000000000000 9000000100449a98 8c326e68047d36df
[    3.963746]         ...
[    3.966170] Call Trace:
[    3.966172] [<9000000002faffec>] i2c_get_match_data+0x48/0xac
[    3.974304] [<9000000002ceb734>] it66121_create_bridge+0x15c/0x404
[    3.980446] [<9000000002cf05a8>] ls7a1000_output_init+0x228/0x248
[    3.986503] [<9000000002cee494>] lsdc_pci_probe+0x4dc/0x5b0
[    3.992038] [<9000000002b86b50>] local_pci_probe+0x48/0xa0
[    3.997487] [<90000000023b5d04>] work_for_cpu_fn+0x1c/0x30
[    4.002936] [<90000000023b7c0c>] process_one_work+0x14c/0x288
[    4.008644] [<90000000023b8084>] worker_thread+0x33c/0x438
[    4.014092] [<90000000023c1ccc>] kthread+0x124/0x130
[    4.019023] [<9000000002381188>] ret_from_kernel_thread+0xc/0xa4
[    4.024991]
[    4.026463] Code: 26000079  02c08063  4c000020 <28c24318> 43ffe31f  43ffdeff  2a00030c  43ffd59f  02c012f7
[    4.036154]
[    4.037630] ---[ end trace 0000000000000000 ]---
---
 drivers/gpu/drm/bridge/ite-it66121.c | 51 +++++++++++++++++++---------
 1 file changed, 35 insertions(+), 16 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +35 -16
index 2f7f00f1bedb..8971414a2a60 100644
@@ -292,8 +292,39 @@ enum chip_id {
 struct it66121_chip_info {
 	enum chip_id id;
 	u16 vid, pid;
+	char name[24];
 };
 
+static const struct it66121_chip_info it66121_chip_info[] = {
+	{
+		.id = ID_IT66121,
+		.vid = 0x4954,
+		.pid = 0x0612,
+		.name = "IT66121",
+	},
+	{
+		.id = ID_IT6610,
+		.vid = 0xca00,
+		.pid = 0x0611,
+		.name = "IT6610",
+	},
+};
+
+static const struct it66121_chip_info *
+it66121_get_match_data(u16 vender_id, u16 device_id)
+{
+	const struct it66121_chip_info *info;
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(it66121_chip_info); i++) {
+		info = &it66121_chip_info[i];
+		if (info->vid == vender_id && info->pid == device_id)
+			return info;
+	}
+
+	return NULL;
+}
+
 struct it66121_ctx {
 	struct regmap *regmap;
 	struct drm_bridge bridge;
@@ -1677,28 +1708,16 @@ static void it66121_remove(struct i2c_client *client)
 	mutex_destroy(&ctx->lock);
 }
 
-static const struct it66121_chip_info it66121_chip_info = {
-	.id = ID_IT66121,
-	.vid = 0x4954,
-	.pid = 0x0612,
-};
-
-static const struct it66121_chip_info it6610_chip_info = {
-	.id = ID_IT6610,
-	.vid = 0xca00,
-	.pid = 0x0611,
-};
-
 static const struct of_device_id it66121_dt_match[] = {
-	{ .compatible = "ite,it66121", &it66121_chip_info },
-	{ .compatible = "ite,it6610", &it6610_chip_info },
+	{ .compatible = "ite,it66121", &it66121_chip_info[0] },
+	{ .compatible = "ite,it6610", &it66121_chip_info[1] },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, it66121_dt_match);
 
 static const struct i2c_device_id it66121_id[] = {
-	{ "it66121", (kernel_ulong_t) &it66121_chip_info },
-	{ "it6610", (kernel_ulong_t) &it6610_chip_info },
+	{ "it66121", (kernel_ulong_t) &it66121_chip_info[0] },
+	{ "it6610", (kernel_ulong_t) &it66121_chip_info[1] },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, it66121_id);
Signature · 1 line
2.34.1
#23 lore raw

Re: [PATCH 7/8] drm/bridge: it66121: Add another implementation for getting match data

Quoted 49 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

Because if use the i2c_get_match_data() function on our platform, the following error will emerge.

[    3.597872] ACPI: bus type drm_connector registered
[    3.602877] loongson 0000:00:06.1: Found LS7A1000 bridge chipset, revision: 1
[    3.610013] loongson 0000:00:06.1: [drm] dc: 264MHz, gmc: 529MHz, gpu: 529MHz
[    3.617111] loongson 0000:00:06.1: [drm] Dedicated vram start: 0xe0030000000, size: 64MiB
[    3.633628] loongson 0000:00:06.1: [drm] Loongson VBIOS version: 0.3
[    3.639944] loongson 0000:00:06.1: [drm] Loongson VBIOS: has 8 DCBs
[    3.646271] Console: switching to colour dummy device 80x25
[    3.651902] loongson 0000:00:06.1: [drm] VRAM: 4096 pages ready
[    3.657791] loongson 0000:00:06.1: [drm] GTT: 32768 pages ready
[    3.663731] loongson 0000:00:06.1: [drm] lsdc-i2c0(sda pin mask=1, scl pin mask=2) created
[    3.671966] loongson 0000:00:06.1: [drm] lsdc-i2c1(sda pin mask=4, scl pin mask=8) created
[    3.680188] loongson 0000:00:06.1: [drm] DisplayPipe-0 has DVO-0 connector
[    3.711860] debugfs: Directory '1-004c' with parent 'regmap' already present!
[    3.720312] CPU 0 Unable to handle kernel paging request at virtual address 0000000000000090, era == 9000000002faffec, ra == 9000000002faffc8
[    3.732935] Oops[#1]:
[    3.735187] CPU: 0 PID: 8 Comm: kworker/0:0 Not tainted 6.6.0-rc3+ #941
[    3.741757] Hardware name: Loongson Loongson-3A5000-7A1000-1w-ML5A/Loongson-LS3A5000-7A1000-1w-ML5A, BIOS vUDK2018-LoongArch-V4.0.05-test-stable202305 06/
[    3.755500] Workqueue: events work_for_cpu_fn
[    3.759833] pc 9000000002faffec ra 9000000002faffc8 tp 900000010017c000 sp 900000010017fb80
[    3.768132] a0 0000000000000000 a1 9000000101c00420 a2 0000000000000001 a3 900000010017fbc0
[    3.776430] a4 0000000000000004 a5 0000000000000000 a6 0000000000000001 a7 0000000000000001
[    3.784727] t0 0000000000000000 t1 0000000000000001 t2 0000000006124954 t3 0000000000000012
[    3.793026] t4 0000000000004954 t5 900000000800b530 t6 0000000000000000 t7 0000000000018500
[    3.801324] t8 90000001019c90c0 u0 9000000101c00c00 s9 fffffffffffff000 s0 9000000101c00400
[    3.809621] s1 0000000000000000 s2 0000000000000000 s3 9000000003c42cb0 s4 9000000101c00420
[    3.817920] s5 900000010017fc48 s6 0000000000000000 s7 0000000000000000 s8 90000000037fa000
[    3.826219]    ra: 9000000002faffc8 i2c_get_match_data+0x24/0xac
[    3.832189]   ERA: 9000000002faffec i2c_get_match_data+0x48/0xac
[    3.838156]  CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE)
[    3.844303]  PRMD: 00000004 (PPLV0 +PIE -PWE)
[    3.848631]  EUEN: 00000000 (-FPE -SXE -ASXE -BTE)
[    3.853391]  ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
[    3.858149] ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0)
[    3.863599]  BADV: 0000000000000090
[    3.867058]  PRID: 0014c011 (Loongson-64bit, Loongson-3A5000)
[    3.872764] Modules linked in:
[    3.875793] Process kworker/0:0 (pid: 8, threadinfo=(____ptrval____), task=(____ptrval____))
[    3.884180] Stack : 9000000101c00400 0000000000000000 900000010177f428 9000000002ceb734
[    3.892137]         9000000101c00404 90000000037fa000 900000010017fc60 9000000101c00400
[    3.900093]         9000000016124954 8c326e68047d36df 0000004c037fa000 900000010017fc50
[    3.908050]         0000000000000080 9000000003c44490 900000010017fcb0 90000001003e9ec0
[    3.916007]         0000000000000001 900000010044f000 900000010017fc60 9000000101c00400
[    3.923964]         90000000037fa000 9000000002cf05a8 90000001003e8000 900000010017fcb2
Quoted 8 lines
[    3.931920]         000000304c17fc68 0000000000000000 000000000000004c 0000000000000000
[    3.939877]         4031323136365449 0000000000006334 004c000000000000 0000000000000000
[    3.947833]         0000000000000000 0000000000000000 0000000000000000 0000000000000000
[    3.955790]         0000000000000000 0000000000000000 9000000100449a98 8c326e68047d36df
[    3.963746]         ...
[    3.966170] Call Trace:
[    3.966172] [<9000000002faffec>] i2c_get_match_data+0x48/0xac
[    3.974304] [<9000000002ceb734>] it66121_create_bridge+0x15c/0x404

This function gets added only in patch 8, it is not broken otherwise.

I can only repeat my suggestion from the previous series: register a proper I2C device. Don't try to overplay Linux device model.

Quoted 98 lines
[    3.980446] [<9000000002cf05a8>] ls7a1000_output_init+0x228/0x248
[    3.986503] [<9000000002cee494>] lsdc_pci_probe+0x4dc/0x5b0
[    3.992038] [<9000000002b86b50>] local_pci_probe+0x48/0xa0
[    3.997487] [<90000000023b5d04>] work_for_cpu_fn+0x1c/0x30
[    4.002936] [<90000000023b7c0c>] process_one_work+0x14c/0x288
[    4.008644] [<90000000023b8084>] worker_thread+0x33c/0x438
[    4.014092] [<90000000023c1ccc>] kthread+0x124/0x130
[    4.019023] [<9000000002381188>] ret_from_kernel_thread+0xc/0xa4
[    4.024991]
[    4.026463] Code: 26000079  02c08063  4c000020 <28c24318> 43ffe31f  43ffdeff  2a00030c  43ffd59f  02c012f7
[    4.036154]
[    4.037630] ---[ end trace 0000000000000000 ]---
---
 drivers/gpu/drm/bridge/ite-it66121.c | 51 +++++++++++++++++++---------
 1 file changed, 35 insertions(+), 16 deletions(-)
drivers/gpu/drm/bridge/ite-it66121.c +35 -17
index 2f7f00f1bedb..8971414a2a60 100644
@@ -292,8 +292,39 @@ enum chip_id {
 struct it66121_chip_info {
        enum chip_id id;
        u16 vid, pid;
+       char name[24];
 };
 
+static const struct it66121_chip_info it66121_chip_info[] = {
+       {
+               .id = ID_IT66121,
+               .vid = 0x4954,
+               .pid = 0x0612,
+               .name = "IT66121",
+       },
+       {
+               .id = ID_IT6610,
+               .vid = 0xca00,
+               .pid = 0x0611,
+               .name = "IT6610",
+       },
+};
+
+static const struct it66121_chip_info *
+it66121_get_match_data(u16 vender_id, u16 device_id)
+{
+       const struct it66121_chip_info *info;
+       unsigned int i;
+
+       for (i = 0; i < ARRAY_SIZE(it66121_chip_info); i++) {
+               info = &it66121_chip_info[i];
+               if (info->vid == vender_id && info->pid == device_id)
+                       return info;
+       }
+
+       return NULL;
+}
+
 struct it66121_ctx {
        struct regmap *regmap;
        struct drm_bridge bridge;
@@ -1677,28 +1708,16 @@ static void it66121_remove(struct i2c_client *client)
        mutex_destroy(&ctx->lock);
 }
 
-static const struct it66121_chip_info it66121_chip_info = {
-       .id = ID_IT66121,
-       .vid = 0x4954,
-       .pid = 0x0612,
-};
-
-static const struct it66121_chip_info it6610_chip_info = {
-       .id = ID_IT6610,
-       .vid = 0xca00,
-       .pid = 0x0611,
-};
-
 static const struct of_device_id it66121_dt_match[] = {
-       { .compatible = "ite,it66121", &it66121_chip_info },
-       { .compatible = "ite,it6610", &it6610_chip_info },
+       { .compatible = "ite,it66121", &it66121_chip_info[0] },
+       { .compatible = "ite,it6610", &it66121_chip_info[1] },
        { }
 };
 MODULE_DEVICE_TABLE(of, it66121_dt_match);
 
 static const struct i2c_device_id it66121_id[] = {
-       { "it66121", (kernel_ulong_t) &it66121_chip_info },
-       { "it6610", (kernel_ulong_t) &it6610_chip_info },
+       { "it66121", (kernel_ulong_t) &it66121_chip_info[0] },
+       { "it6610", (kernel_ulong_t) &it66121_chip_info[1] },
        { }
 };
 MODULE_DEVICE_TABLE(i2c, it66121_id);
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#24 lore raw

PATCH 8/8 drm/bridge: it66121: Allow link this driver as a lib

In reply to Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
 include/drm/bridge/ite-it66121.h     |  17 ++++
 2 files changed, 113 insertions(+), 38 deletions(-)
 create mode 100644 include/drm/bridge/ite-it66121.h
drivers/gpu/drm/bridge/ite-it66121.c +96 -38
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
 #include <drm/drm_edid.h>
 #include <drm/drm_modes.h>
 #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
 				 enum drm_bridge_attach_flags flags)
 {
 	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+	struct drm_bridge *next_bridge = ctx->next_bridge;
+	struct drm_encoder *encoder = bridge->encoder;
 	int ret;
 
-	if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-		return -EINVAL;
+	if (next_bridge) {
+		if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+			WARN_ON(1);
+			flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+		}
+		ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+		if (ret)
+			return ret;
+	} else {
+		struct drm_connector *connector;
 
-	ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-	if (ret)
-		return ret;
+		if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+			WARN_ON(1);
+
+		connector = drm_bridge_connector_init(bridge->dev, encoder);
+		if (IS_ERR(connector))
+			return PTR_ERR(connector);
+
+		drm_connector_attach_encoder(connector, encoder);
+
+		ctx->connector = connector;
+	}
 
 	if (ctx->info->id == ID_IT66121) {
 		ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
 	"vcn33", "vcn18", "vrf12"
 };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+			  bool hpd_support, bool audio_support,
+			  struct drm_bridge **bridge)
 {
+	struct device *dev = &client->dev;
 	int ret;
 	struct it66121_ctx *ctx;
-	struct device *dev = &client->dev;
-
-	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-		dev_err(dev, "I2C check functionality failed.\n");
-		return -ENXIO;
-	}
 
 	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
 	if (!ctx)
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client *client)
 
 	ctx->dev = dev;
 	ctx->client = client;
-	ctx->info = i2c_get_match_data(client);
-
-	ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-	if (ret)
-		return ret;
-
-	ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-	if (ret)
-		return ret;
-
-	i2c_set_clientdata(client, ctx);
 	mutex_init(&ctx->lock);
 
-	ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
-					     it66121_supplies);
-	if (ret) {
-		dev_err(dev, "Failed to enable power supplies\n");
-		return ret;
+	if (of_support) {
+		ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
+		if (ret)
+			return ret;
+
+		ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+		if (ret)
+			return ret;
+	} else {
+		ctx->bus_width = 24;
+		ctx->next_bridge = NULL;
 	}
 
 	it66121_hw_reset(ctx);
@@ -1679,33 +1690,80 @@ static int it66121_probe(struct i2c_client *client)
 	if (ret)
 		return ret;
 
-	if (ctx->vender_id != ctx->info->vid ||
-	    ctx->device_id != ctx->info->pid)
+	ctx->info = it66121_get_match_data(ctx->vender_id, ctx->device_id);
+	if (!ctx->info)
 		return -ENODEV;
 
-	ret = devm_request_threaded_irq(dev, client->irq, NULL,	it66121_irq_threaded_handler,
-					IRQF_ONESHOT, dev_name(dev), ctx);
-	if (ret < 0) {
-		dev_err(dev, "Failed to request irq %d:%d\n", client->irq, ret);
-		return ret;
+	if (hpd_support) {
+		ret = devm_request_threaded_irq(dev, client->irq, NULL,
+						it66121_irq_threaded_handler,
+						IRQF_ONESHOT, dev_name(dev),
+						ctx);
+		if (ret < 0) {
+			dev_err(dev, "Failed to request irq: %d\n", ret);
+			return ret;
+		}
 	}
 
 	it66121_bridge_init_base(&ctx->bridge, dev->of_node, true);
 
-	it66121_audio_codec_init(ctx, dev);
+	if (audio_support)
+		it66121_audio_codec_init(ctx, dev);
+
+	*bridge = &ctx->bridge;
 
 	dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
 		 ctx->vender_id, ctx->device_id, ctx->revision);
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(it66121_create_bridge);
+
+static int it66121_probe(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct it66121_ctx *ctx;
+	struct drm_bridge *bridge;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(dev, "I2C check functionality failed.\n");
+		return -ENXIO;
+	}
+
+	ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
+					     it66121_supplies);
+	if (ret) {
+		dev_err(dev, "Failed to enable power supplies\n");
+		return ret;
+	}
+
+	ret = it66121_create_bridge(client, true, true, true, &bridge);
+	if (ret)
+		return ret;
+
+	ctx = bridge_to_it66121(bridge);
+
+	i2c_set_clientdata(client, ctx);
+
+	return 0;
+}
+
+void it66121_destroy_bridge(struct drm_bridge *bridge)
+{
+	struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+
+	drm_bridge_remove(bridge);
+
+	mutex_destroy(&ctx->lock);
+}
+EXPORT_SYMBOL_GPL(it66121_destroy_bridge);
 
 static void it66121_remove(struct i2c_client *client)
 {
 	struct it66121_ctx *ctx = i2c_get_clientdata(client);
 
-	drm_bridge_remove(&ctx->bridge);
-	mutex_destroy(&ctx->lock);
+	it66121_destroy_bridge(&ctx->bridge);
 }
 
 static const struct of_device_id it66121_dt_match[] = {
include/drm/bridge/ite-it66121.h new file +17 -0
new file mode 100644
index 000000000000..e6753f695b7f
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __ITE_IT66121_H__
+#define __ITE_IT66121_H__
+
+#include <linux/i2c.h>
+
+#include <drm/drm_bridge.h>
+#include <drm/drm_device.h>
+
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+			  bool hpd_support, bool audio_support,
+			  struct drm_bridge **bridge);
+
+void it66121_destroy_bridge(struct drm_bridge *bridge);
+
+#endif
Signature · 1 line
2.34.1
#25 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 29 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
 drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
 include/drm/bridge/ite-it66121.h     |  17 ++++
 2 files changed, 113 insertions(+), 38 deletions(-)
 create mode 100644 include/drm/bridge/ite-it66121.h
drivers/gpu/drm/bridge/ite-it66121.c +1 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
 #include <drm/drm_edid.h>
 #include <drm/drm_modes.h>
 #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                 enum drm_bridge_attach_flags flags)
 {

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 10 lines
drivers/gpu/drm/bridge/ite-it66121.c +5 -2
        struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
        int ret;
 
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 13 lines
drivers/gpu/drm/bridge/ite-it66121.c +9 -3
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 729

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 51 lines
drivers/gpu/drm/bridge/ite-it66121.c +9 -23
+
+               ctx->connector = connector;
+       }
 
        if (ctx->info->id == ID_IT66121) {
                ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
        "vcn33", "vcn18", "vrf12"
 };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
 {
+       struct device *dev = &client->dev;
        int ret;
        struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
 
        ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
        if (!ctx)
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client *client)
 
        ctx->dev = dev;
        ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
        mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
-                                            it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev, &ctx->bus_width);

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1681

Quoted 10 lines
drivers/gpu/drm/bridge/ite-it66121.c +9 -0
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+               if (ret)
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
        }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +0 -2
        it66121_hw_reset(ctx);
@@ -1679,33 +1690,80 @@ static int it66121_probe(struct i2c_client *client)
        if (ret)
                return ret;
 
-       if (ctx->vender_id != ctx->info->vid ||
-           ctx->device_id != ctx->info->pid)

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1697

Quoted 10 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -5
+       ctx->info = it66121_get_match_data(ctx->vender_id, ctx->device_id);
+       if (!ctx->info)
                return -ENODEV;
 
-       ret = devm_request_threaded_irq(dev, client->irq, NULL, it66121_irq_threaded_handler,
-                                       IRQF_ONESHOT, dev_name(dev), ctx);
-       if (ret < 0) {
-               dev_err(dev, "Failed to request irq %d:%d\n", client->irq, ret);
-               return ret;
+       if (hpd_support) {

Who handles HPD in your platform case?

Quoted 101 lines
drivers/gpu/drm/bridge/ite-it66121.c +54 -3
+               ret = devm_request_threaded_irq(dev, client->irq, NULL,
+                                               it66121_irq_threaded_handler,
+                                               IRQF_ONESHOT, dev_name(dev),
+                                               ctx);
+               if (ret < 0) {
+                       dev_err(dev, "Failed to request irq: %d\n", ret);
+                       return ret;
+               }
        }
 
        it66121_bridge_init_base(&ctx->bridge, dev->of_node, true);
 
-       it66121_audio_codec_init(ctx, dev);
+       if (audio_support)
+               it66121_audio_codec_init(ctx, dev);
+
+       *bridge = &ctx->bridge;
 
        dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
                 ctx->vender_id, ctx->device_id, ctx->revision);
 
        return 0;
 }
+EXPORT_SYMBOL_GPL(it66121_create_bridge);
+
+static int it66121_probe(struct i2c_client *client)
+{
+       struct device *dev = &client->dev;
+       struct it66121_ctx *ctx;
+       struct drm_bridge *bridge;
+       int ret;
+
+       if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+               dev_err(dev, "I2C check functionality failed.\n");
+               return -ENXIO;
+       }
+
+       ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
+                                            it66121_supplies);
+       if (ret) {
+               dev_err(dev, "Failed to enable power supplies\n");
+               return ret;
+       }
+
+       ret = it66121_create_bridge(client, true, true, true, &bridge);
+       if (ret)
+               return ret;
+
+       ctx = bridge_to_it66121(bridge);
+
+       i2c_set_clientdata(client, ctx);
+
+       return 0;
+}
+
+void it66121_destroy_bridge(struct drm_bridge *bridge)
+{
+       struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+
+       drm_bridge_remove(bridge);
+
+       mutex_destroy(&ctx->lock);
+}
+EXPORT_SYMBOL_GPL(it66121_destroy_bridge);
 
 static void it66121_remove(struct i2c_client *client)
 {
        struct it66121_ctx *ctx = i2c_get_clientdata(client);
 
-       drm_bridge_remove(&ctx->bridge);
-       mutex_destroy(&ctx->lock);
+       it66121_destroy_bridge(&ctx->bridge);
 }
 
 static const struct of_device_id it66121_dt_match[] = {
include/drm/bridge/ite-it66121.h new file +17 -1
new file mode 100644
index 000000000000..e6753f695b7f
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __ITE_IT66121_H__
+#define __ITE_IT66121_H__
+
+#include <linux/i2c.h>
+
+#include <drm/drm_bridge.h>
+#include <drm/drm_device.h>
+
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge);
+
+void it66121_destroy_bridge(struct drm_bridge *bridge);
+
+#endif
--

2.34.1

Signature · 2 lines
With best wishes
Dmitry
#26 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
  drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
  include/drm/bridge/ite-it66121.h     |  17 ++++
  2 files changed, 113 insertions(+), 38 deletions(-)

create mode 100644 include/drm/bridge/ite-it66121.h

drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
  #include <drm/drm_atomic_helper.h>
  #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
  #include <drm/drm_edid.h>
  #include <drm/drm_modes.h>
  #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                  enum drm_bridge_attach_flags flags)
  {
         struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
         int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

Quoted 18 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 729

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
         if (ctx->info->id == ID_IT66121) {
                 ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
         "vcn33", "vcn18", "vrf12"
  };
#27 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 70 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
  drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
  include/drm/bridge/ite-it66121.h     |  17 ++++
  2 files changed, 113 insertions(+), 38 deletions(-)

create mode 100644 include/drm/bridge/ite-it66121.h

drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
  #include <drm/drm_atomic_helper.h>
  #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
  #include <drm/drm_edid.h>
  #include <drm/drm_modes.h>
  #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                  enum drm_bridge_attach_flags flags)
  {
         struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
         int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 20 lines
Quoted 20 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 729

Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
         if (ctx->info->id == ID_IT66121) {
                 ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
         "vcn33", "vcn18", "vrf12"
  };
Signature · 2 lines
With best wishes
Dmitry
#28 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 78 lines · Dmitry Baryshkov
Quoted 67 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
   drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
   include/drm/bridge/ite-it66121.h     |  17 ++++
   2 files changed, 113 insertions(+), 38 deletions(-)

create mode 100644 include/drm/bridge/ite-it66121.h

drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
   #include <drm/drm_atomic_helper.h>
   #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
   #include <drm/drm_edid.h>
   #include <drm/drm_modes.h>
   #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                   enum drm_bridge_attach_flags flags)
   {
          struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
          int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 11 lines
Quoted 7 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display bridge(say it66121) in the middle. After all, there is no *direct physical connection* from the perspective of the hardware. I means that there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a perfect abstract on the software side. Especially for such a simple use case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

Quoted 20 lines
Quoted 18 lines
Quoted 18 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 729

Quoted 7 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
          if (ctx->info->id == ID_IT66121) {
                  ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
          "vcn33", "vcn18", "vrf12"
   };
#29 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 100 lines · Sui Jingfeng

Hi,

Quoted 78 lines · Dmitry Baryshkov
Quoted 67 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
   drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
   include/drm/bridge/ite-it66121.h     |  17 ++++
   2 files changed, 113 insertions(+), 38 deletions(-)

create mode 100644 include/drm/bridge/ite-it66121.h

drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
   #include <drm/drm_atomic_helper.h>
   #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
   #include <drm/drm_edid.h>
   #include <drm/drm_modes.h>
   #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                   enum drm_bridge_attach_flags flags)
   {
          struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
          int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 11 lines
Quoted 7 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one. The host can not specify the DRM_BRIDGE_ATTACH_NO_CONNECTOR)

Quoted 31 lines
Quoted 14 lines
Quoted 4 lines
Quoted 4 lines
Quoted 1 line

+ WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 11 lines
Quoted 7 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one. The host can not specify the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

Quoted 22 lines
Quoted 22 lines
Quoted 20 lines
Quoted 20 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 729

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
          if (ctx->info->id == ID_IT66121) {
                  ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
          "vcn33", "vcn18", "vrf12"
   };
Signature · 2 lines
With best wishes
Dmitry
#30 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 157 lines · Dmitry Baryshkov
Quoted 96 lines · Sui Jingfeng

Hi,

Quoted 78 lines · Dmitry Baryshkov
Quoted 67 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
    drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
    include/drm/bridge/ite-it66121.h     |  17 ++++
    2 files changed, 113 insertions(+), 38 deletions(-)
    create mode 100644 include/drm/bridge/ite-it66121.h
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
    #include <drm/drm_atomic_helper.h>
    #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
    #include <drm/drm_edid.h>
    #include <drm/drm_modes.h>
    #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                    enum drm_bridge_attach_flags flags)
    {
           struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
           int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one. The host can not specify the DRM_BRIDGE_ATTACH_NO_CONNECTOR)

Quoted 28 lines
Quoted 14 lines
Quoted 4 lines
Quoted 4 lines
Quoted 1 line

+ WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

Quoted 3 lines

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

No, I'm only intend to modify the one when there has a user emerged. If we have the connector related code in the KMS display driver side, then I think we don't honor the meaning of the word *bridge*. I was told drm_bridge is a modern design, if we still need the DC side worry about something do not have a physical connection, then it will not be modern anymore, it is not a good bridge.

Quoted 3 lines

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one.

Yes and no!

If one of them are transparent, then thisimplementation still can works. It is just that this will not be a good abstract anymore.I do have seen such design on some notebook hardware. But from my programming experiences, using two bridges are typically a bad practice in engineering. As it tend
to increase the PCB board area and increase entire cost. As you need buy
one more TX encoder chip. Please also consider that the embedded world focus
on low cost and low power consume.

I think, multiple display bridges case should be avoided for middle/low end application. Or allow us to handle the two and/or more bridges cases in the future. When there has at least one user emerged, we will introduce new approach to handle then.

Do you find any product level boards that using two external display bridge and one of them is it66121? If we can not even find a user, we are not even have a board to test if current design (state of art) works. Does it suffer from module loading order problems? what if their i2c slave address is same? Does such a use case will past the S3/S4 test? All of those concerns are imposed to every display bridges programmer from the very beginning.

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Quoted 4 lines

The host can not specify the
DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flagare implement-defined, for our case, I could just ignore it if their don't have a signal(DT or ACPI) tell me that there are multiple bridges in the chain. This depend on community's attitude.

For it66121 with a canonical design, the host should not need to specify this flag. Because at the time of when the device driver(it66121.ko) get loaded, the it66121 driver could parse the DT by itself, and detect if there has a next bridge, is it a connector or is it yet another display bridges. The DT speak everything about the topology. The flag is there just for the KMS display controller driver to explicit control, use it and make it more useful is the right way, is it?

Quoted 21 lines
Quoted 19 lines
Quoted 19 lines
Quoted 18 lines
Quoted 18 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 729

Quoted 7 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
           if (ctx->info->id == ID_IT66121) {
                   ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
           "vcn33", "vcn18", "vrf12"
    };
#31 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 166 lines · Sui Jingfeng

Hi,

Quoted 157 lines · Dmitry Baryshkov
Quoted 96 lines · Sui Jingfeng

Hi,

Quoted 78 lines · Dmitry Baryshkov
Quoted 67 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
    drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
    include/drm/bridge/ite-it66121.h     |  17 ++++
    2 files changed, 113 insertions(+), 38 deletions(-)
    create mode 100644 include/drm/bridge/ite-it66121.h
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
    #include <drm/drm_atomic_helper.h>
    #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
    #include <drm/drm_edid.h>
    #include <drm/drm_modes.h>
    #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                    enum drm_bridge_attach_flags flags)
    {
           struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
           int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one. The host can not specify the DRM_BRIDGE_ATTACH_NO_CONNECTOR)

Quoted 28 lines
Quoted 14 lines
Quoted 4 lines
Quoted 4 lines
Quoted 1 line

+ WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

Quoted 3 lines

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Quoted 6 lines

No, I'm only intend to modify the one when there has a user emerged. If we have the connector related code in the KMS display driver side, then I think we don't honor the meaning of the word *bridge*. I was told drm_bridge is a modern design, if we still need the DC side worry about something do not have a physical connection, then it will not be modern anymore, it is not a good bridge.

Next time the user emerges for another bridge. And then for another. This way the very similar code is copy-pasted over all bridge drivers. So instead it was decided to keep it in the display driver code.

Quoted 6 lines
Quoted 5 lines

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one.

Quoted 8 lines

Yes and no!

If one of them are transparent, then thisimplementation still can works. It is just that this will not be a good abstract anymore.I do have seen such design on some notebook hardware. But from my programming experiences, using two bridges are typically a bad practice in engineering. As it tend
to increase the PCB board area and increase entire cost. As you need buy
one more TX encoder chip. Please also consider that the embedded world focus
on low cost and low power consume.

A typical pipeline for an embedded device can perfectly look like:
- DSI host (drm_encoder)
- DSI-HDMI or DSI-eDP bridge (drm_bridge)
- hdmi-connector or panel-bridge (drm_bridge)
- drm_bridge_connector.

Two drm_bridge instances.

Quoted 6 lines

I think, multiple display bridges case should be avoided for middle/low end application. Or allow us to handle the two and/or more bridges cases in the future. When there has at least one user emerged, we will introduce new approach to handle then.

Quoted 6 lines

Do you find any product level boards that using two external display bridge and one of them is it66121? If we can not even find a user, we are not even have a board to test if current design (state of art) works. Does it suffer from module loading order problems? what if their i2c slave address is same? Does such a use case will past the S3/S4 test? All of those concerns are imposed to every display bridges programmer from the very beginning.

Please add a hdmi-connector device to your testing model. You don't have to use it, but it is a fully legit use case. And suddenly you have to drm_bridge instances in your chain.

Quoted 4 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

Quoted 7 lines
Quoted 5 lines

The host can not specify the
DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flagare implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Quoted 3 lines

for our case, I could just ignore it if their
don't have a signal(DT or ACPI) tell me that there are multiple bridges in the chain. This depend on community's attitude.

Ignoring a flag is a bad idea.

Quoted 7 lines

For it66121 with a canonical design, the host should not need to specify this flag. Because at the time of when the device driver(it66121.ko) get loaded, the it66121 driver could parse the DT by itself, and detect if there has a next bridge, is it a connector or is it yet another display bridges. The DT speak everything about the topology. The flag is there just for the KMS display controller driver to explicit control, use it and make it more useful is the right way, is it?

No. We have been there (before the DRM_BRIDGE_ATTACH_NO_CONNECTOR was introduced), we have gone away from it.

Quoted 23 lines
Quoted 23 lines
Quoted 21 lines
Quoted 21 lines
Quoted 20 lines
Quoted 20 lines

drivers/gpu/drm/bridge/ite-it66121.c

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
           if (ctx->info->id == ID_IT66121) {
                   ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
           "vcn33", "vcn18", "vrf12"
    };
Signature · 2 lines
With best wishes
Dmitry
maintainer
#32 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 193 lines · Dmitry Baryshkov
Quoted 166 lines · Sui Jingfeng

Hi,

Quoted 157 lines · Dmitry Baryshkov
Quoted 96 lines · Sui Jingfeng

Hi,

Quoted 78 lines · Dmitry Baryshkov
Quoted 67 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 34 lines · Dmitry Baryshkov
Quoted 33 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
     drivers/gpu/drm/bridge/ite-it66121.c | 134 +++++++++++++++++++--------
     include/drm/bridge/ite-it66121.h     |  17 ++++
     2 files changed, 113 insertions(+), 38 deletions(-)
     create mode 100644 include/drm/bridge/ite-it66121.h
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
     #include <drm/drm_atomic_helper.h>
     #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
     #include <drm/drm_edid.h>
     #include <drm/drm_modes.h>
     #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                     enum drm_bridge_attach_flags flags)
     {
            struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
            int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 8 lines
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+                       flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 723

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one. The host can not specify the DRM_BRIDGE_ATTACH_NO_CONNECTOR)

Quoted 28 lines
Quoted 14 lines
Quoted 4 lines
Quoted 4 lines
Quoted 1 line

+ WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

Quoted 3 lines

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Quoted 6 lines

No, I'm only intend to modify the one when there has a user emerged. If we have the connector related code in the KMS display driver side, then I think we don't honor the meaning of the word *bridge*. I was told drm_bridge is a modern design, if we still need the DC side worry about something do not have a physical connection, then it will not be modern anymore, it is not a good bridge.

Next time the user emerges for another bridge. And then for another. This way the very similar code is copy-pasted over all bridge drivers. So instead it was decided to keep it in the display driver code.

Quoted 6 lines
Quoted 5 lines

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one.

Quoted 8 lines

Yes and no!

If one of them are transparent, then thisimplementation still can works. It is just that this will not be a good abstract anymore.I do have seen such design on some notebook hardware. But from my programming experiences, using two bridges are typically a bad practice in engineering. As it tend
to increase the PCB board area and increase entire cost. As you need buy
one more TX encoder chip. Please also consider that the embedded world focus
on low cost and low power consume.

Quoted 7 lines

A typical pipeline for an embedded device can perfectly look like:
- DSI host (drm_encoder)
- DSI-HDMI or DSI-eDP bridge (drm_bridge)
- hdmi-connector or panel-bridge (drm_bridge)
- drm_bridge_connector.

Two drm_bridge instances.

Nowadays, we are moving the encoder code into bridge so we can have way more than 2 bridges, and connector code has been moved to a bridge.

On Amlogic SoCs, the HDMI chain has at least 3 bridges, it can have up to 4 on DSI usecase if you plug a DSI to eDP bridge.

On iMX8 platform, they have multiple internal SoC bridges even before the HDMI or DSI bridge.

The model works very well across extremely heterogeneous embedded platforms.

Quoted 80 lines
Quoted 7 lines

I think, multiple display bridges case should be avoided for middle/low end application. Or allow us to handle the two and/or more bridges cases in the future. When there has at least one user emerged, we will introduce new approach to handle then.

Quoted 6 lines

Do you find any product level boards that using two external display bridge and one of them is it66121? If we can not even find a user, we are not even have a board to test if current design (state of art) works. Does it suffer from module loading order problems? what if their i2c slave address is same? Does such a use case will past the S3/S4 test? All of those concerns are imposed to every display bridges programmer from the very beginning.

Please add a hdmi-connector device to your testing model. You don't have to use it, but it is a fully legit use case. And suddenly you have to drm_bridge instances in your chain.

Quoted 4 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

Quoted 7 lines
Quoted 5 lines

The host can not specify the
DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flagare implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Quoted 3 lines

for our case, I could just ignore it if their
don't have a signal(DT or ACPI) tell me that there are multiple bridges in the chain. This depend on community's attitude.

Ignoring a flag is a bad idea.

Quoted 7 lines

For it66121 with a canonical design, the host should not need to specify this flag. Because at the time of when the device driver(it66121.ko) get loaded, the it66121 driver could parse the DT by itself, and detect if there has a next bridge, is it a connector or is it yet another display bridges. The DT speak everything about the topology. The flag is there just for the KMS display controller driver to explicit control, use it and make it more useful is the right way, is it?

No. We have been there (before the DRM_BRIDGE_ATTACH_NO_CONNECTOR was introduced), we have gone away from it.

Quoted 23 lines
Quoted 23 lines
Quoted 21 lines
Quoted 21 lines
Quoted 20 lines
Quoted 20 lines

drivers/gpu/drm/bridge/ite-it66121.c

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +6 -0
+
+               connector = drm_bridge_connector_init(bridge->dev, encoder);
+               if (IS_ERR(connector))
+                       return PTR_ERR(connector);
+
+               drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
            if (ctx->info->id == ID_IT66121) {
                    ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
            "vcn33", "vcn18", "vrf12"
     };
#33 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 209 lines · Neil Armstrong
Quoted 197 lines · Dmitry Baryshkov
Quoted 170 lines · Sui Jingfeng

Hi,

Quoted 161 lines · Dmitry Baryshkov
Quoted 100 lines · Sui Jingfeng

Hi,

Quoted 82 lines · Dmitry Baryshkov
Quoted 71 lines · Sui Jingfeng

Hi,

Thanks a lot for reviewing!

Quoted 36 lines · Dmitry Baryshkov
Quoted 35 lines · Sui Jingfeng

From: Sui Jingfeng <[email protected]>

The it66121_create_bridge() and it66121_destroy_bridge() are added to export the core functionalities. Create a connector manually by using bridge connector helpers when link as a lib.

---
     drivers/gpu/drm/bridge/ite-it66121.c | 134
+++++++++++++++++++--------
     include/drm/bridge/ite-it66121.h     |  17 ++++

     2 files changed, 113 insertions(+), 38 deletions(-)

     create mode 100644 include/drm/bridge/ite-it66121.h

drivers/gpu/drm/bridge/ite-it66121.c +3 -0
index 8971414a2a60..f5968b679c5d 100644
@@ -22,6 +22,7 @@
 
      #include <drm/drm_atomic_helper.h>
      #include <drm/drm_bridge.h>
+#include <drm/drm_bridge_connector.h>
      #include <drm/drm_edid.h>
      #include <drm/drm_modes.h>
      #include <drm/drm_print.h>
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct 
 drm_bridge *bridge,
                                      enum drm_bridge_attach_flags flags)
      {
             struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
             int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct · line 714

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Originally I want to

Quoted 9 lines
Quoted 9 lines
drivers/gpu/drm/bridge/ite-it66121.c +7 -0
+ flags |= DRM_BRIDGE_ATTACH_NO_CONNECTOR;
+               }
+               ret = drm_bridge_attach(encoder, next_bridge, 
 bridge, flags);
+               if (ret)
+                       return ret;
+       } else {
+               struct drm_connector *connector;
 
Quoted 9 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct · line 726

Quoted 6 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -3
-       ret = drm_bridge_attach(bridge->encoder, 
 ctx->next_bridge, bridge, flags);
-       if (ret)
-               return ret;
+               if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)
+                       WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a  decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one. The host can not specify the DRM_BRIDGE_ATTACH_NO_CONNECTOR)

Quoted 28 lines
Quoted 14 lines
Quoted 4 lines
Quoted 4 lines
Quoted 1 line

+ WARN_ON(1);

No. It is perfectly fine to create attach a bridge with no next_bridge and with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag.

Quoted 9 lines

The document say when DRM_BRIDGE_ATTACH_NO_CONNECTOR flag is set the bridge shall not create a drm_connector. So I think if a display bridge driver don't have a next bridge attached (Currently, this is told by the DT), it says that this is a non-DT environment. On such a case, this display bridge driver(it66121.ko) should behavior like a *agent*. Because the upstream port of it66121 is the DVO port of the display controller, the downstream port of it66121 is the HDMI connector. it66121 is on the middle. So I think the it66121.ko should handle all of troubles on behalf of the display controller drivers.

No. Don't make decisions for the other drivers. They might have different needs.

[...]

Quoted 10 lines
Quoted 6 lines

Therefore (when in non-DT use case), the display controller drivers side should not set DRM_BRIDGE_ATTACH_NO_CONNECTOR flag anymore. Which is to hint that the it66121 should totally in charge of those tasks (either by using bridge connector helper or create a connector manually). I don't understand on such a case, why bother display controller drivers anymore.

This is the reason why we had introduced this flag. It allows the driver to customise the connector. It even allows the driver to implement a connector on its own, completely ignoring the drm_bridge_connector.

Quoted 12 lines

I know what you said is right in the sense of the universe cases,
but I think the most frequent(majority) use case is that there is
only one display bridge on the middle. Therefore, I don't want to
movethe connector things into device driver if there is only one display
bridge(say it66121) in the middle. After all, there is no *direct
physical connection* from the perspective of the hardware. I means that
there is no hardware wires connectthe HDMI connector and the DVO port. So display controller drivers should not interact with anything related with the connector on a
perfect abstract on the software side. Especially for such a simple use
case. It probably make senses to make a  decision for themost frequently use case, please also note that this patch didn't introduce any-restriction for the more advance
uses cases(multiple bridges in the middle).

Quoted 3 lines

So, for the sake of not having the connector in the display driver, you want to add boilerplate code basically to each and every bridge driver. In the end, they should all behave in the same way.

Quoted 6 lines

No, I'm only intend to modify the one when there has a user emerged. If we have the connector related code in the KMS display driver side, then I think we don't honor the meaning of the word *bridge*. I was told drm_bridge is a modern design, if we still need the DC side worry about something do not have a physical connection, then it will not be modern anymore, it is not a good bridge.

Next time the user emerges for another bridge. And then for another. This way the very similar code is copy-pasted over all bridge drivers. So instead it was decided to keep it in the display driver code.

Quoted 6 lines
Quoted 5 lines

Moreover, there is no way this implementation can work without a warning if there are two bridges in a chain and the it66121 is the second (the last) one.

Quoted 8 lines

Yes and no!

If one of them are transparent, then thisimplementation still can works. It is just that this will not be a good abstract anymore.I do have seen such design on some notebook hardware.  But from my programming experiences, using two bridges are typically a bad practice in engineering. As it tend
to increase the PCB board area and increase entire cost. As you need buy
one more TX encoder chip. Please also consider that the embedded world focus
on low cost and low power consume.

Quoted 7 lines

A typical pipeline for an embedded device can perfectly look like:
- DSI host (drm_encoder)
- DSI-HDMI or DSI-eDP bridge (drm_bridge)
- hdmi-connector or panel-bridge (drm_bridge)
- drm_bridge_connector.

Two drm_bridge instances.

Nowadays, we are moving the encoder code into bridge so we can have way more than 2 bridges, and connector code has been moved to a bridge.

Quoted 7 lines

On Amlogic SoCs, the HDMI chain has at least 3 bridges, it can have up to 4 on DSI usecase if you plug a DSI to eDP bridge.

On iMX8 platform, they have multiple internal SoC bridges even before the HDMI or DSI bridge.

The model works very well across extremely heterogeneous embedded platforms.

But you don't mention the prerequisite, there have difference between display bridge devices *inside* of the SoC and display bridge devices *outside* of the SoC. IT66121 is a onboard device. Suppose you are the hardware vendor ITE, you definitely want your chip can be used on any platform. The model probably works well on ARM, but on X86 platform there no DT support, the abstract for the onboard device becomes pale.

Quoted 83 lines
Quoted 82 lines
Quoted 7 lines

I think, multiple display bridges case should be avoided for middle/low end application. Or allow us to handle the two and/or more bridges cases in the future. When there has at least one user emerged, we will introduce new approach to handle then.

Quoted 6 lines

Do you find any product level boards that using two external display bridge and one of them is it66121? If we can not even find a user, we are not even have a board to test if current design (state of art) works. Does it suffer from module loading order problems? what if their i2c slave address is same? Does such a use case will past the S3/S4 test? All of those concerns are imposed to every display bridges programmer from the very beginning.

Please add a hdmi-connector device to your testing model. You don't have to use it, but it is a fully legit use case. And suddenly you have to drm_bridge instances in your chain.

Quoted 4 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

Quoted 7 lines
Quoted 5 lines

The host can not specify the
DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flagare implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Quoted 3 lines

for our case, I could just ignore it if their
don't have a signal(DT or ACPI) tell me that there are multiple bridges in the chain. This depend on community's attitude.

Ignoring a flag is a bad idea.

Quoted 7 lines

For it66121 with a canonical design, the host should not need to specify this flag. Because at the time of when the device driver(it66121.ko) get loaded, the it66121 driver could parse the DT by itself, and detect if there has a next bridge, is it a connector or is it yet another display bridges. The DT speak everything about the topology. The flag is there just for the KMS display controller driver to explicit control, use it and make it more useful is the right way, is it?

No. We have been there (before the DRM_BRIDGE_ATTACH_NO_CONNECTOR was introduced), we have gone away from it.

Quoted 25 lines
Quoted 25 lines
Quoted 23 lines
Quoted 23 lines
Quoted 22 lines
Quoted 22 lines
Quoted 10 lines

+
+               connector = drm_bridge_connector_init(bridge->dev, encoder); +               if (IS_ERR(connector))
+                       return PTR_ERR(connector); +
+ drm_connector_attach_encoder(connector, encoder);

This goes into your device driver.

Quoted 10 lines

+
+               ctx->connector = connector;
+       }

            if (ctx->info->id == ID_IT66121) {
                    ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,

drivers/gpu/drm/bridge/ite-it66121.c +0 -0
@@ -1632,16 +1651,13 @@ static const char * const 
 it66121_supplies[] = {

            "vcn33", "vcn18", "vrf12"
     };

#34 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 3 lines · Dmitry Baryshkov
Quoted 1 line

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flag are implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Then, my problem is that do we allow create a drm_connector instance in drm bridge driver nowadays?

#35 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 4 lines · Sui Jingfeng

Hi,

Quoted 8 lines
Quoted 3 lines · Dmitry Baryshkov
Quoted 1 line

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flag are implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Then, my problem is that do we allow create a drm_connector instance in drm bridge driver nowadays?

Yes, if there is no DRM_BRIDGE_ATTACH_NO_CONNECTOR. But that's deprecated IMO.

Signature · 2 lines
With best wishes
Dmitry
#36 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 4 lines · Dmitry Baryshkov
Quoted 3 lines · Sui Jingfeng

Hi,

Quoted 8 lines
Quoted 7 lines · Dmitry Baryshkov
Quoted 3 lines
Quoted 1 line

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flag are implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Then, my problem is that do we allow create a drm_connector instance in drm bridge driver nowadays?

Yes, if there is no DRM_BRIDGE_ATTACH_NO_CONNECTOR. But that's deprecated IMO.

Then can you read the code in bridge/ti-tfp410.c please?
The tfp410_attach() function will create drm_connector instance manually if the conditional (flags == 0) is true.

#37 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 4 lines · Dmitry Baryshkov
Quoted 4 lines
Quoted 4 lines

The host can not specify the
DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

Quoted 8 lines
Quoted 1 line

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flagare implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Quoted 3 lines

for our case, I could just ignore it if their
don't have a signal(DT or ACPI) tell me that there are multiple bridges in the chain. This depend on community's attitude.

Ignoring a flag is a bad idea.

Can you also read the code in the bridge/lontium-lt8912.c please? when flags == 0 is true, the lt8912 driver will just create a drm_connector instance in the drm bridge drivers. The behavior is similar with this patch in the perspective of spirit.

And the most important thing is that no matter what the flag the upstream port is passed, lt8912 just always pass the DRM_BRIDGE_ATTACH_NO_CONNECTOR flags to the next bridge. Does this count as a kind of ignore? or

This is to say that both the lt8912 and the tfp410 drm bridge drivers are allowing create a drm_connector manually in drm bridge drivers. They didn't being asked to move the drm_connector related code to display controller driver. I don't know why I can't follow this way?

Do you really read the code before do comments or I failed to understand something?

#38 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 24 lines · Sui Jingfeng

Hi,

Quoted 4 lines · Dmitry Baryshkov
Quoted 4 lines
Quoted 4 lines

The host can not specify the
DRM_BRIDGE_ATTACH_NO_CONNECTOR flag, it will cause a warning here. And it can not omit the flag (as otherwise the first bridge will create a connector, without consulting the second bridge).

Quoted 8 lines
Quoted 1 line

The semantics of DRM_BRIDGE_ATTACH_NO_CONNECTOR flagare implement-defined,

No, they are not. Semantics are pretty simple: do not create the drm_connector instance. Pass the flag to the next bridge in the chain.

Quoted 3 lines

for our case, I could just ignore it if their
don't have a signal(DT or ACPI) tell me that there are multiple bridges in the chain. This depend on community's attitude.

Ignoring a flag is a bad idea.

Can you also read the code in the bridge/lontium-lt8912.c please? when flags == 0 is true, the lt8912 driver will just create a drm_connector instance in the drm bridge drivers. The behavior is similar with this patch in the perspective of spirit.

Quoted 8 lines

And the most important thing is that no matter what the flag the upstream port is passed, lt8912 just always pass the DRM_BRIDGE_ATTACH_NO_CONNECTOR flags to the next bridge. Does this count as a kind of ignore? or

This is to say that both the lt8912 and the tfp410 drm bridge drivers are allowing create a drm_connector manually in drm bridge drivers. They didn't being asked to move the drm_connector related code to display controller driver. I don't know why I can't follow this way?

This is called 'legacy'.

Quoted 2 lines

Do you really read the code before do comments or I failed to understand something?

Signature · 2 lines
With best wishes
Dmitry
#39 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 5 lines · Dmitry Baryshkov
Quoted 3 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

What you said is just for the more complex uses case. I can't agree, sorry.

By choosing the word "canonical design", I means that the most frequently used cases in practice are the canonical design, 95+% motherboards I have seen has only one *onboard* display bridges chip. For my driver, I abstract the internal (inside of the chip) encoder as drm_encoder and abstract the external TX chip as drm_bridge, this design still works very well.

Originally, I means that this is a concept of the hardware design. You are wrong even through in the software design context, the transparent simple drm bridge drivers(simple-bridge.c) also *allow* to create drm connector manually. I don't think I need to emulate more example, please read the code by youself.

Canonical or not canonical is not a question to argue, if other programmers are allowed to do such kind of abstraction, I should also allowed too. Thanks.

maintainer
#40 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 16 lines · Sui Jingfeng
Quoted 5 lines · Dmitry Baryshkov
Quoted 3 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

What you said is just for the more complex uses case. I can't agree, sorry.

By choosing the word "canonical design", I means that the most frequently used cases in practice are the canonical design, 95+% motherboards I have seen has only one *onboard* display bridges chip. For my driver, I abstract the internal (inside of the chip) encoder as drm_encoder and abstract the external TX chip as drm_bridge, this design still works very well.

Quoted 5 lines

Originally, I means that this is a concept of the hardware design. You are wrong even through in the software design context, the transparent simple drm bridge drivers(simple-bridge.c) also *allow* to create drm connector manually. I don't think I need to emulate more example, please read the code by youself.

Ok. That's it. We've been patient long enough. You have been given a review and a list of things to fix for your driver to be merged. Whether you follow them or not is your decision.

We won't tolerate insulting comments though.

Maxime

#41 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 16 lines · Maxime Ripard
Quoted 15 lines · Sui Jingfeng
Quoted 5 lines · Dmitry Baryshkov
Quoted 3 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

What you said is just for the more complex uses case. I can't agree, sorry.

By choosing the word "canonical design", I means that the most frequently used cases in practice are the canonical design, 95+% motherboards I have seen has only one *onboard* display bridges chip. For my driver, I abstract the internal (inside of the chip) encoder as drm_encoder and abstract the external TX chip as drm_bridge, this design still works very well.

Quoted 5 lines
Quoted 5 lines

Originally, I means that this is a concept of the hardware design. You are wrong even through in the software design context, the transparent simple drm bridge drivers(simple-bridge.c) also *allow* to create drm connector manually. I don't think I need to emulate more example, please read the code by youself.

'emulate' -> 'enumerate'

Quoted 2 lines

Ok. That's it. We've been patient long enough. You have been given a review and a list of things to fix for your driver to be merged.

This series is not relevant to my driver, can we please *limit* the discussion to this series?

Quoted 2 lines

Whether
you follow them or not is your decision.

I'm not saying that I will not follow, just to make sure what's solution is you want. I need discussion to figure out.

Quoted 1 line

We won't tolerate insulting comments though.

There is *no* insulting, please don't misunderstanding before *sufficient* communication, OK? Originally, I thought Dmitry may ignore(or overlook) what is the current status.

Quoted 1 line

Maxime

maintainer
#42 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 25 lines · Sui Jingfeng

Hi,

Quoted 16 lines · Maxime Ripard
Quoted 15 lines · Sui Jingfeng
Quoted 5 lines · Dmitry Baryshkov
Quoted 3 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

What you said is just for the more complex uses case. I can't agree, sorry.

By choosing the word "canonical design", I means that the most frequently used cases in practice are the canonical design, 95+% motherboards I have seen has only one *onboard* display bridges chip. For my driver, I abstract the internal (inside of the chip) encoder as drm_encoder and abstract the external TX chip as drm_bridge, this design still works very well.

Quoted 5 lines
Quoted 5 lines

Originally, I means that this is a concept of the hardware design. You are wrong even through in the software design context, the transparent simple drm bridge drivers(simple-bridge.c) also *allow* to create drm connector manually. I don't think I need to emulate more example, please read the code by youself.

Quoted 7 lines

'emulate' -> 'enumerate'

Quoted 2 lines

Ok. That's it. We've been patient long enough. You have been given a review and a list of things to fix for your driver to be merged.

This series is not relevant to my driver, can we please *limit* the discussion to this series?

Right, I conflated the two, I meant this series, or the general goal to enable that bridge with your driver. The rest of the driver is of course unaffected.

Quoted 4 lines
Quoted 1 line

Whether you follow them or not is your decision.

I'm not saying that I will not follow, just to make sure what's solution is you want. I need discussion to figure out.

You had direct, repeated, feedback on that already by a maintainer and one of the most experienced dev and reviewer on bridges. If you need more guidance, you can definitely ask questions, but asking questions and telling them they are wrong is very different.

Quoted 5 lines
Quoted 1 line

We won't tolerate insulting comments though.

There is *no* insulting, please don't misunderstanding before *sufficient* communication, OK? Originally, I thought Dmitry may ignore(or overlook) what is the current status.

Saying to someone maintaining and/or reviewing that code for years now that they are wrong and should go read the code is insulting.

Maxime

#43 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 43 lines · Maxime Ripard
Quoted 24 lines · Sui Jingfeng

Hi,

Quoted 16 lines · Maxime Ripard
Quoted 15 lines · Sui Jingfeng
Quoted 5 lines · Dmitry Baryshkov
Quoted 3 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

What you said is just for the more complex uses case. I can't agree, sorry.

By choosing the word "canonical design", I means that the most frequently used cases in practice are the canonical design, 95+% motherboards I have seen has only one *onboard* display bridges chip. For my driver, I abstract the internal (inside of the chip) encoder as drm_encoder and abstract the external TX chip as drm_bridge, this design still works very well.

Quoted 5 lines
Quoted 5 lines

Originally, I means that this is a concept of the hardware design. You are wrong even through in the software design context, the transparent simple drm bridge drivers(simple-bridge.c) also *allow* to create drm connector manually. I don't think I need to emulate more example, please read the code by youself.

Quoted 6 lines

'emulate' -> 'enumerate'

Quoted 2 lines

Ok. That's it. We've been patient long enough. You have been given a review and a list of things to fix for your driver to be merged.

This series is not relevant to my driver, can we please *limit* the discussion to this series?

Right, I conflated the two, I meant this series, or the general goal to enable that bridge with your driver. The rest of the driver is of course unaffected.

Quoted 3 lines
Quoted 1 line

Whether you follow them or not is your decision.

I'm not saying that I will not follow, just to make sure what's solution is you want. I need discussion to figure out.

You had direct, repeated, feedback on that already by a maintainer and one of the most experienced dev and reviewer on bridges. If you need more guidance, you can definitely ask questions, but asking questions and telling them they are wrong is very different.

Quoted 6 lines
Quoted 4 lines
Quoted 1 line

We won't tolerate insulting comments though.

There is *no* insulting, please don't misunderstanding before *sufficient* communication, OK? Originally, I thought Dmitry may ignore(or overlook) what is the current status.

Saying to someone maintaining and/or reviewing that code for years now that they are wrong and should go read the code is insulting.

OK, I will remind my written words in the future.
I will back to investigate for a period of time.
Thanks a lot for reviewing.

Quoted 1 line

Maxime

#44 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Maxime Ripard
Quoted 43 lines · Maxime Ripard
Quoted 24 lines · Sui Jingfeng

Hi,

Quoted 16 lines · Maxime Ripard
Quoted 15 lines · Sui Jingfeng
Quoted 5 lines · Dmitry Baryshkov
Quoted 3 lines

I'm agree with the idea that drm bridges drivers involved toward to a direction that support more complex design, but I think we should also leave a way for the most frequent use case. Make it straight-forward as a canonical design.

Not having anything connector-related in the drm_bridge driver is a canonical design.

What you said is just for the more complex uses case. I can't agree, sorry.

By choosing the word "canonical design", I means that the most frequently used cases in practice are the canonical design, 95+% motherboards I have seen has only one *onboard* display bridges chip. For my driver, I abstract the internal (inside of the chip) encoder as drm_encoder and abstract the external TX chip as drm_bridge, this design still works very well.

Quoted 5 lines
Quoted 5 lines

Originally, I means that this is a concept of the hardware design. You are wrong even through in the software design context, the transparent simple drm bridge drivers(simple-bridge.c) also *allow* to create drm connector manually. I don't think I need to emulate more example, please read the code by youself.

Quoted 6 lines

'emulate' -> 'enumerate'

Quoted 2 lines

Ok. That's it. We've been patient long enough. You have been given a review and a list of things to fix for your driver to be merged.

This series is not relevant to my driver, can we please *limit* the discussion to this series?

Right, I conflated the two, I meant this series, or the general goal to enable that bridge with your driver. The rest of the driver is of course unaffected.

Quoted 3 lines
Quoted 1 line

Whether you follow them or not is your decision.

I'm not saying that I will not follow, just to make sure what's solution is you want. I need discussion to figure out.

You had direct, repeated, feedback on that already by a maintainer and one of the most experienced dev and reviewer on bridges. If you need more guidance, you can definitely ask questions, but asking questions and telling them they are wrong is very different.

Quoted 6 lines
Quoted 4 lines
Quoted 1 line

We won't tolerate insulting comments though.

There is *no* insulting, please don't misunderstanding before *sufficient* communication, OK? Originally, I thought Dmitry may ignore(or overlook) what is the current status.

Saying to someone maintaining and/or reviewing that code for years now that they are wrong and should go read the code is insulting.

Back to that time, I'm focus on kindly technique debating, this is a kind of defensive reply for the patch. This is a kind of remind in case of ignores. Probably a bit of negative, but please don't misunderstanding as insult anyway.

Dmitry, really thanks a lot for the instructs, I have learned a lot while talking with you. I will back to try mentioned method.

#45 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -0
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                  enum drm_bridge_attach_flags flags)
  {
         struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
         int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

If (next_bridge) is true, it says that the driver *already* known that
it66121 have a next bridges attached. Then it66121 driver should certainly
attach it, no matter what it is. Either a connector or another display bridge.
It also says that this is a DT-based system on such a case. CallingWARN_ON(1) here helps to see(print) which DC driver is doing the wired things. Ok, I will remove the WARN_ON(1) on the next version.

#46 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 20 lines · Sui Jingfeng

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 8 lines
drivers/gpu/drm/bridge/ite-it66121.c +2 -0
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                  enum drm_bridge_attach_flags flags)
  {
         struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
         int ret;
 
Quoted 6 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -2
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Quoted 5 lines

If (next_bridge) is true, it says that the driver *already* known that
it66121 have a next bridges attached. Then it66121 driver should certainly
attach it, no matter what it is. Either a connector or another display bridge.
It also says that this is a DT-based system on such a case. CallingWARN_ON(1) here helps to see(print) which DC driver is doing the wired things. Ok, I will remove the WARN_ON(1) on the next version.

That's why I pointed you to WARN(). WARN_ON(1) gives no information to the user. WARN() allows you to add a message.

Signature · 2 lines
With best wishes
Dmitry
#47 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 21 lines · Dmitry Baryshkov
Quoted 20 lines · Sui Jingfeng

Hi,

Quoted 14 lines · Dmitry Baryshkov

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_bridge_attach(struct drm_bridge *bridge, · line 713

Quoted 13 lines
drivers/gpu/drm/bridge/ite-it66121.c +5 -2
@@ -703,14 +704,32 @@ static int it66121_bridge_attach(struct drm_bridge *bridge,
                                  enum drm_bridge_attach_flags flags)
  {
         struct it66121_ctx *ctx = bridge_to_it66121(bridge);
+       struct drm_bridge *next_bridge = ctx->next_bridge;
+       struct drm_encoder *encoder = bridge->encoder;
         int ret;
 
-       if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR))
-               return -EINVAL;
+       if (next_bridge) {
+               if (!(flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR)) {
+                       WARN_ON(1);

Why? At least use WARN() instead

Quoted 8 lines
Quoted 5 lines

If (next_bridge) is true, it says that the driver *already* known that
it66121 have a next bridges attached. Then it66121 driver should certainly
attach it, no matter what it is. Either a connector or another display bridge.
It also says that this is a DT-based system on such a case. CallingWARN_ON(1) here helps to see(print) which DC driver is doing the wired things. Ok, I will remove the WARN_ON(1) on the next version.

That's why I pointed you to WARN(). WARN_ON(1) gives no information to the user. WARN() allows you to add a message.

Please use drm_WARN* while at it.

BR,
Jani.

Signature · 1 line
Jani Nikula, Intel
#48 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 56 lines · Dmitry Baryshkov
Quoted 56 lines
drivers/gpu/drm/bridge/ite-it66121.c +14 -23
+
+               ctx->connector = connector;
+       }
 
         if (ctx->info->id == ID_IT66121) {
                 ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
         "vcn33", "vcn18", "vrf12"
  };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
  {
+       struct device *dev = &client->dev;
         int ret;
         struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
 
         ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
         if (!ctx)
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client *client)
 
         ctx->dev = dev;
         ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
         mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
-                                            it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+               if (ret)
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1681

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +4 -0
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
         }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Honestly, I don't want to leave any scratch(breadcrumbs).
I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch *still* be useful in the DT world. Because the newly introduced it66121_create_bridge() function is a core. I think It's better leave this task to a more advance programmer. if there have use case. It can be introduced at a latter time, probably parallel with the DT.

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more prefer to turn this driver to support hot-plug, even remove the device on the run time freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has a corresponding struct device representation in linux kernel.

so I still think It is best to make this drivers functional as a static lib, but I want to hear you to say more. Why it would be a *better* alternative to turn OF calls into fwnode calls? what are the potential benefits?

#49 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 71 lines · Sui Jingfeng

Hi,

Quoted 56 lines · Dmitry Baryshkov
Quoted 56 lines
drivers/gpu/drm/bridge/ite-it66121.c +14 -23
+
+               ctx->connector = connector;
+       }
 
         if (ctx->info->id == ID_IT66121) {
                 ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
         "vcn33", "vcn18", "vrf12"
  };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
  {
+       struct device *dev = &client->dev;
         int ret;
         struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
 
         ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
         if (!ctx)
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client *client)
 
         ctx->dev = dev;
         ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
         mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
-                                            it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+               if (ret)
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1681

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +4 -0
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
         }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 5 lines

Honestly, I don't want to leave any scratch(breadcrumbs).
I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch *still* be useful in the DT world.

fwnode calls work for both DT and non-DT cases. In the DT case they work with DT nodes and properties. In the non-DT case, they work with manually populated properties.

Quoted 11 lines

Because the newly introduced it66121_create_bridge()
function is a core. I think It's better leave this task to a more advance programmer. if there have use case. It can be introduced at a latter time, probably parallel with the DT.

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more prefer to turn this driver to support hot-plug, even remove the device on the run time freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has a corresponding struct device representation in linux kernel.

It has. See i2c_client::dev.

Quoted 3 lines

so I still think It is best to make this drivers functional as a static lib, but I want to hear you to say more. Why it would be a *better* alternative to turn OF calls into fwnode calls? what are the potential benefits?

Because then you can populate device properties from your root device. Because it allows the platform to specify the bus width instead of hardcoding 24 bits (which might work in your case, but might not be applicable to another user next week).

Anyway, even without fwnode, I'd strongly suggest you to drop the it66121_create_bridge() as it is now and start by populating the i2c bus from your root device. Then you will need some way (fwnode?) to discover the bridge chain. And at the last point you will get into the device data and/or properties business.

Signature · 2 lines
With best wishes
Dmitry
#50 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 84 lines · Dmitry Baryshkov
Quoted 69 lines · Sui Jingfeng

Hi,

Quoted 56 lines · Dmitry Baryshkov
Quoted 56 lines
drivers/gpu/drm/bridge/ite-it66121.c +14 -23
+
+               ctx->connector = connector;
+       }
 
          if (ctx->info->id == ID_IT66121) {
                  ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,
@@ -1632,16 +1651,13 @@ static const char * const it66121_supplies[] = {
          "vcn33", "vcn18", "vrf12"
   };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
   {
+       struct device *dev = &client->dev;
          int ret;
          struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
 
          ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
          if (!ctx)
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client *client)
 
          ctx->dev = dev;
          ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
          mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
-                                            it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
+               if (ret)
Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1681

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +4 -0
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
          }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 5 lines

Honestly, I don't want to leave any scratch(breadcrumbs).
I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch *still* be useful in the DT world.

fwnode calls work for both DT and non-DT cases. In the DT case they work with DT nodes and properties. In the non-DT case, they work with manually populated properties.

Quoted 5 lines

Because the newly introduced it66121_create_bridge()
function is a core. I think It's better leave this task to a more advance programmer. if there have use case. It can be introduced at a latter time, probably parallel with the DT.

Quoted 7 lines
Quoted 6 lines

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more prefer to turn this driver to support hot-plug, even remove the device on the run time freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has a corresponding struct device representation in linux kernel.

It has. See i2c_client::dev.

No, what I mean is that there don't have a device driver for monitor(display) hardware entity. And the drm_do_probe_ddc_edid() is the static linked driver, which is similar with the idea this series want to express.

Quoted 7 lines
Quoted 3 lines

so I still think It is best to make this drivers functional as a static lib, but I want to hear you to say more. Why it would be a *better* alternative to turn OF calls into fwnode calls? what are the potential benefits?

Because then you can populate device properties from your root device. Because it allows the platform to specify the bus width instead of hardcoding 24 bits (which might work in your case, but might not be applicable to another user next week).

No, this problem can be easily solved. Simply add another argument.

```

int it66121_create_bridge(struct i2c_client *client, bool of_support,
                          bool hpd_support, bool audio_support, u32 bus_width,
                          struct drm_bridge **bridge);
```
Quoted 3 lines

Anyway, even without fwnode, I'd strongly suggest you to drop the it66121_create_bridge() as it is now and start by populating the i2c bus from your root device.

This will force all non-DT users to add the similar code patter at the display controller side, which is another kind of duplication. The monitor is also as I2C slave device, can be abstract as a identify drm bridges in theory, I guess.

Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

#51 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 127 lines · Sui Jingfeng

Hi,

Quoted 91 lines · Dmitry Baryshkov
Quoted 76 lines · Sui Jingfeng

Hi,

Quoted 63 lines · Dmitry Baryshkov
Quoted 63 lines

+
+               ctx->connector = connector;
+       }

          if (ctx->info->id == ID_IT66121) {
                  ret = regmap_write_bits(ctx->regmap, IT66121_CLK_BANK_REG,

(quoted diff) +0 -0
@@ -1632,16 +1651,13 @@ static const char * const 
 it66121_supplies[] = {

          "vcn33", "vcn18", "vrf12"
   };

(quoted diff) +1 -1
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool 

of_support,
+                         bool hpd_support, bool audio_support, +                         struct drm_bridge **bridge)
   {
+       struct device *dev = &client->dev;
          int ret;
          struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n"); -               return -ENXIO;
-       }

          ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); if (!ctx)

drivers/gpu/drm/bridge/ite-it66121.c +6 -16
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client 
 *client)
 
           ctx->dev = dev;
           ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
           mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev, 
 ARRAY_SIZE(it66121_supplies),
- it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev, 
 &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev, 

&ctx->next_bridge);
+               if (ret)

Quoted 8 lines
Quoted 5 lines

+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
          }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 5 lines

Honestly, I don't want to leave any scratch(breadcrumbs).
I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch *still* be useful in the DT world.

fwnode calls work for both DT and non-DT cases. In the DT case they work with DT nodes and properties. In the non-DT case, they work with manually populated properties.

Quoted 5 lines

Because the newly introduced it66121_create_bridge()
function is a core. I think It's better leave this task to a more advance programmer. if there have use case. It can be introduced at a latter time, probably parallel with the DT.

Quoted 7 lines
Quoted 6 lines

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more prefer to turn this driver to support hot-plug, even remove the device on the run time freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has a corresponding struct device representation in linux kernel.

It has. See i2c_client::dev.

No, what I mean is that there don't have a device driver for monitor(display) hardware entity. And the drm_do_probe_ddc_edid() is the static linked driver, which is similar with the idea this series want to express.

Quoted 7 lines
Quoted 3 lines

so I still think It is best to make this drivers functional as a static lib, but I want to hear you to say more. Why it would be a *better* alternative to turn OF calls into fwnode calls? what are the potential benefits?

Because then you can populate device properties from your root device. Because it allows the platform to specify the bus width instead of hardcoding 24 bits (which might work in your case, but might not be applicable to another user next week).

No, this problem can be easily solved. Simply add another argument.

```

int it66121_create_bridge(struct i2c_client *client, bool of_support,
                          bool hpd_support, bool audio_support, u32 bus_width,
                          struct drm_bridge **bridge);
```
Quoted 8 lines
Quoted 3 lines

Anyway, even without fwnode, I'd strongly suggest you to drop the it66121_create_bridge() as it is now and start by populating the i2c bus from your root device.

This will force all non-DT users to add the similar code patter at the display controller side, which is another kind of duplication. The monitor is also as I2C slave device, can be abstract as a identify drm bridges in theory, I guess.

'identify' -> 'identity'

Quoted 9 lines
Quoted 5 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

#52 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 115 lines · Sui Jingfeng
Quoted 112 lines · Sui Jingfeng

Hi,

Quoted 108 lines · Dmitry Baryshkov
Quoted 77 lines · Sui Jingfeng

Hi,

Quoted 64 lines · Dmitry Baryshkov
Quoted 64 lines
drivers/gpu/drm/bridge/ite-it66121.c +3 -0
+
+               ctx->connector = connector;
+       }
 
          if (ctx->info->id == ID_IT66121) {
                  ret = regmap_write_bits(ctx->regmap,

IT66121_CLK_BANK_REG,

drivers/gpu/drm/bridge/ite-it66121.c +4 -7
@@ -1632,16 +1651,13 @@ static const char * const
 it66121_supplies[] = {
          "vcn33", "vcn18", "vrf12"
   };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool
 of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
   {
+       struct device *dev = &client->dev;
          int ret;
          struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter,
 I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
          ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
          if (!ctx)
drivers/gpu/drm/bridge/ite-it66121.c +6 -16
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client
 *client)
 
          ctx->dev = dev;
          ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
          mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev,
 ARRAY_SIZE(it66121_supplies),
- it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev,
 &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev,

&ctx->next_bridge);
+ if (ret)

Quoted 8 lines

drivers/gpu/drm/bridge/ite-it66121.c static int it66121_probe(struct i2c_client *client) · line 1681

Quoted 5 lines
drivers/gpu/drm/bridge/ite-it66121.c +4 -0
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
          }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 7 lines

Honestly, I don't want to leave any scratch(breadcrumbs). I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch
*still* be useful in the DT world.

fwnode calls work for both DT and non-DT cases. In the DT case they work with DT nodes and properties. In the non-DT case, they work with manually populated properties.

Quoted 18 lines

Because the newly introduced it66121_create_bridge() function is a core. I think It's better leave this task to a more advance programmer.
if there have use case. It can be introduced at a latter time, probably parallel with
the DT.

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is
a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more
prefer to turn this driver to support hot-plug, even remove the device on the run time
freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which
contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has
a corresponding struct device representation in linux kernel.

Quoted 7 lines
Quoted 7 lines
Quoted 1 line

It has. See i2c_client::dev.

No, what I mean is that there don't have a device driver for monitor(display) hardware entity.
And the drm_do_probe_ddc_edid() is the static linked driver, which is similar with the idea
this series want to express.

Because the monitor is not a part of the display pipeline.

Quoted 28 lines
Quoted 28 lines
Quoted 11 lines
Quoted 7 lines

so I still think It is best to make this drivers functional as a static lib, but I want
to hear you to say more. Why it would be a *better* alternative to turn OF calls into
fwnode calls? what are the potential benefits?

Because then you can populate device properties from your root device. Because it allows the platform to specify the bus width instead of hardcoding 24 bits (which might work in your case, but might not be applicable to another user next week).

No, this problem can be easily solved. Simply add another argument.

```

int it66121_create_bridge(struct i2c_client *client, bool of_support,
                          bool hpd_support, bool audio_support, u32
bus_width,
                          struct drm_bridge **bridge);
```
Quoted 3 lines

Anyway, even without fwnode, I'd strongly suggest you to drop the it66121_create_bridge() as it is now and start by populating the i2c bus from your root device.

Quoted 18 lines
Quoted 6 lines

This will force all non-DT users to add the similar code patter at the display controller side,
which is another kind of duplication. The monitor is also as I2C slave device, can be abstract
as a identify drm bridges in theory, I guess.

'identify' -> 'identity'

Quoted 8 lines
Quoted 5 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

Signature · 2 lines
With best wishes
Dmitry
#53 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 114 lines · Dmitry Baryshkov
Quoted 113 lines · Sui Jingfeng
Quoted 111 lines · Sui Jingfeng

Hi,

Quoted 107 lines · Dmitry Baryshkov
Quoted 76 lines · Sui Jingfeng

Hi,

Quoted 64 lines · Dmitry Baryshkov
Quoted 64 lines
(quoted diff) +3 -0
+
+               ctx->connector = connector;
+       }
 
           if (ctx->info->id == ID_IT66121) {
                   ret = regmap_write_bits(ctx->regmap,

IT66121_CLK_BANK_REG,

(quoted diff) +4 -7
@@ -1632,16 +1651,13 @@ static const char * const
 it66121_supplies[] = {
           "vcn33", "vcn18", "vrf12"
    };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool
 of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
    {
+       struct device *dev = &client->dev;
           int ret;
           struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter,
 I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
           ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
           if (!ctx)
(quoted diff) +6 -16
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client
 *client)
 
           ctx->dev = dev;
           ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
           mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev,
 ARRAY_SIZE(it66121_supplies),
- it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev,
 &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev,

&ctx->next_bridge);
+ if (ret)

Quoted 8 lines

Review

Quoted 5 lines
(quoted diff) +4 -0
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
           }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 7 lines

Honestly, I don't want to leave any scratch(breadcrumbs). I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch
*still* be useful in the DT world.

fwnode calls work for both DT and non-DT cases. In the DT case they work with DT nodes and properties. In the non-DT case, they work with manually populated properties.

Quoted 18 lines

Because the newly introduced it66121_create_bridge() function is a core. I think It's better leave this task to a more advance programmer.
if there have use case. It can be introduced at a latter time, probably parallel with
the DT.

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is
a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more
prefer to turn this driver to support hot-plug, even remove the device on the run time
freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which
contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has
a corresponding struct device representation in linux kernel.

Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 1 line

It has. See i2c_client::dev.

No, what I mean is that there don't have a device driver for monitor(display) hardware entity.
And the drm_do_probe_ddc_edid() is the static linked driver, which is similar with the idea
this series want to express.

Because the monitor is not a part of the display pipeline.

I think the monitor *is definitely* part of the display pipeline, and it is the most important part of the entire display pipeline.

1)

DPMS, self-refreshing, display timings, resolutions supported, HDR, DSC, gsync and freesync etc can be part of whole mode-set. Please consider what the various ->mode_valid() and -> the atomic_check() are for?

2)

If the monitor is not a part of the display pipeline, then the various display panels hardware should also not be part of the display pipeline. Because they are all belong to display category.

the monitor = panel + panel drive IC(such as RTD2281CL, HT1622, ssd130x).

There are panel bridges which abstract the panel + connector as a drm bridge, why the bare panel can be part of the display pipeline, while the more complex monitor can't be?

maintainer
#54 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 133 lines · Sui Jingfeng
Quoted 114 lines · Dmitry Baryshkov
Quoted 113 lines · Sui Jingfeng
Quoted 111 lines · Sui Jingfeng

Hi,

Quoted 107 lines · Dmitry Baryshkov
Quoted 76 lines · Sui Jingfeng

Hi,

Quoted 64 lines · Dmitry Baryshkov
Quoted 64 lines
(quoted diff) +3 -0
+
+               ctx->connector = connector;
+       }
 
           if (ctx->info->id == ID_IT66121) {
                   ret = regmap_write_bits(ctx->regmap,

IT66121_CLK_BANK_REG,

(quoted diff) +4 -7
@@ -1632,16 +1651,13 @@ static const char * const
 it66121_supplies[] = {
           "vcn33", "vcn18", "vrf12"
    };
 
-static int it66121_probe(struct i2c_client *client)
+int it66121_create_bridge(struct i2c_client *client, bool
 of_support,
+                         bool hpd_support, bool audio_support,
+                         struct drm_bridge **bridge)
    {
+       struct device *dev = &client->dev;
           int ret;
           struct it66121_ctx *ctx;
-       struct device *dev = &client->dev;
-
-       if (!i2c_check_functionality(client->adapter,
 I2C_FUNC_I2C)) {
-               dev_err(dev, "I2C check functionality failed.\n");
-               return -ENXIO;
-       }
           ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
           if (!ctx)
(quoted diff) +6 -16
@@ -1649,24 +1665,19 @@ static int it66121_probe(struct i2c_client
 *client)
 
           ctx->dev = dev;
           ctx->client = client;
-       ctx->info = i2c_get_match_data(client);
-
-       ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
-       if (ret)
-               return ret;
-
-       ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
-       if (ret)
-               return ret;
-
-       i2c_set_clientdata(client, ctx);
           mutex_init(&ctx->lock);
 
-       ret = devm_regulator_bulk_get_enable(dev,
 ARRAY_SIZE(it66121_supplies),
- it66121_supplies);
-       if (ret) {
-               dev_err(dev, "Failed to enable power supplies\n");
-               return ret;
+       if (of_support) {
+               ret = it66121_of_read_bus_width(dev,
 &ctx->bus_width);
+               if (ret)
+                       return ret;
+
+               ret = it66121_of_get_next_bridge(dev,

&ctx->next_bridge);
+ if (ret)

Quoted 8 lines

Review

Quoted 5 lines
(quoted diff) +4 -0
+                       return ret;
+       } else {
+               ctx->bus_width = 24;
+               ctx->next_bridge = NULL;
           }

A better alternative would be to turn OF calls into fwnode calls and to populate the fwnode properties. See drivers/platform/x86/intel/chtwc_int33fe.c for example.

Quoted 7 lines

Honestly, I don't want to leave any scratch(breadcrumbs). I'm worries about that turn OF calls into fwnode calls will leave something unwanted.

Because I am not sure if fwnode calls will make sense in the DT world, while my patch
*still* be useful in the DT world.

fwnode calls work for both DT and non-DT cases. In the DT case they work with DT nodes and properties. In the non-DT case, they work with manually populated properties.

Quoted 18 lines

Because the newly introduced it66121_create_bridge() function is a core. I think It's better leave this task to a more advance programmer.
if there have use case. It can be introduced at a latter time, probably parallel with
the DT.

I think DT and/or ACPI is best for integrated devices, but it66121 display bridges is
a i2c slave device. Personally, I think slave device shouldn't be standalone. I'm more
prefer to turn this driver to support hot-plug, even remove the device on the run time
freely when detach and allow reattach. Like the I2C EEPROM device in the monitor (which
contains the EDID, with I2C slave address 0x50). The I2C EEPROM device *also* don't has
a corresponding struct device representation in linux kernel.

Quoted 8 lines
Quoted 6 lines
Quoted 6 lines
Quoted 1 line

It has. See i2c_client::dev.

No, what I mean is that there don't have a device driver for monitor(display) hardware entity.
And the drm_do_probe_ddc_edid() is the static linked driver, which is similar with the idea
this series want to express.

Because the monitor is not a part of the display pipeline.

I think the monitor *is definitely* part of the display pipeline, and it is the most important part of the entire display pipeline.

1)

DPMS, self-refreshing, display timings, resolutions supported, HDR, DSC, gsync and freesync etc can be part of whole mode-set. Please consider what the various ->mode_valid() and -> the atomic_check() are for?

Quoted 6 lines

2)

If the monitor is not a part of the display pipeline, then the various display panels hardware should also not be part of the display pipeline. Because they are all belong to display category.
the monitor = panel + panel drive IC(such as RTD2281CL, HT1622, ssd130x).

To expand further on that, I guess one of the key difference is that you don't really expect to interact with the EEPROM, you'll only read it, which is fairly different from your bridge.

And if someone wanted to instatiate nvmem devices for the various EEPROMs in the monitor, I would very much welcome that change.

Maxime

#55 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution? I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant. But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

Can I switch back or any other ideas?

#56 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 23 lines · Sui Jingfeng

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution? I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant. But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

Quoted 1 line

Can I switch back or any other ideas?

I keep on repeating: create the i2c device from your root device driver, which parses BIOS data.

Signature · 2 lines
With best wishes
Dmitry
#57 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Hi,

Quoted 22 lines · Dmitry Baryshkov
Quoted 21 lines · Sui Jingfeng

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution? I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant. But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

Quoted 4 lines
Quoted 1 line

Can I switch back or any other ideas?

I keep on repeating: create the i2c device from your root device driver, which parses BIOS data.

This is not my own problems, currently it66121 (but not only) display bridge driver don't works on X86 either. What we are trying to do is to provide a generic, non-platform dependent solution. It is not only relevant to my driver. In fact, this series made no assumption which hardware/display controller will be the user.

I have investigated before respin this patch, there are other hardwares which ship the it66121 display bridge. For example, the Fresco Logic FL2000dx USB 3.0 to VGA display adapter[1][2]. Even the windows have a driver.

[1] https://github.com/FrescoLogic/FL2000
[2] https://oemdrivers.com/graphics-fresco-logic-fl2000

maintainer
#58 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 34 lines · Sui Jingfeng

Hi,

Quoted 22 lines · Dmitry Baryshkov
Quoted 21 lines · Sui Jingfeng

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

  From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution? I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant. But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

Quoted 4 lines
Quoted 1 line

Can I switch back or any other ideas?

I keep on repeating: create the i2c device from your root device driver, which parses BIOS data.

This is not my own problems, currently it66121 (but not only) display bridge driver don't works on X86 either. What we are trying to do is to provide a generic, non-platform dependent solution. It is not only relevant to my driver. In fact, this series made no assumption which hardware/display controller will be the user.

Quoted 6 lines

I have investigated before respin this patch, there are other hardwares which ship the it66121 display bridge. For example, the Fresco Logic FL2000dx USB 3.0 to VGA display adapter[1][2]. Even the windows have a driver.

[1] https://github.com/FrescoLogic/FL2000
[2] https://oemdrivers.com/graphics-fresco-logic-fl2000

Switching to fwnodes, registering an i2c bus and generating fwnode data matching the interconnect architecture is the way.

DRM Bridge transition to fwnode only should be done first, this will open bridge to any architecture and device description (DT or ACPI).

Neil

Quoted 1 line
#59 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Dmitry Baryshkov

Hi,

Quoted 22 lines · Dmitry Baryshkov
Quoted 21 lines · Sui Jingfeng

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution? I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant. But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

Quoted 3 lines
Quoted 1 line

Can I switch back or any other ideas?

I keep on repeating: create the i2c device from your root device driver, which parses BIOS data.

You didn't focus on solve the problem, You are focus on solving me. How does the method that parsing BIOS data can be generic and applied universally?

#60 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

Quoted 27 lines · Sui Jingfeng

Hi,

Quoted 22 lines · Dmitry Baryshkov
Quoted 21 lines · Sui Jingfeng

Hi,

Quoted 8 lines · Dmitry Baryshkov
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution? I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant. But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

Quoted 8 lines
Quoted 3 lines
Quoted 1 line

Can I switch back or any other ideas?

I keep on repeating: create the i2c device from your root device driver, which parses BIOS data.

You didn't focus on solve the problem, You are focus on solving me. How does the method that parsing BIOS data can be generic and applied universally?

Parsing BIOS data is unique to your platform (as well as your BIOS tables). However using and extending (instead of replacing it just for your platform) is a generic item.

Signature · 2 lines
With best wishes
Dmitry
maintainer
#61 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Sui Jingfeng
Quoted 7 lines · Sui Jingfeng

Hi,

Quoted 4 lines · Dmitry Baryshkov
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines

Then you will need some way (fwnode?) to
discover the bridge chain. And at the last point you will get into the device data and/or properties business.

Quoted 8 lines
Quoted 4 lines
Quoted 3 lines
Quoted 3 lines

No, leave that chance to a more better programmer and forgive me please, too difficult, I'm afraid of not able to solve. Thanks a lot for the trust!

From my point of view: no.

I respect the fact that the community prefer generic mechanisms. If our approach is not what the community want, can I switch back to my previous solution?

By your previous solution, you mean rolling your own bridge driver? If so, then no, it's not acceptable either.

Quoted 3 lines

I can reduce the duplication of our localized it66121 driver to a minimal, rewrite it until it meets the community's requirement. I know our device looks weird and our approach is not elegant.

I'm glad we agree then :)

Quoted 3 lines

But at the very least, we could not mess the community's design up by localize. Otherwise, I don't know what is the better approach to solve such a problem.

I think there's a gap between what we want from you and what you want from us.

What we really care about is maintenance. In other words, it's mostly about two things:

- Once you and/or your company have moved on to other things, how easy it will be for us to keep that driver in good shape, and how much it will hold back any future development.

- If we want to do a big rework, how much your driver will stand in the way.

That's pretty much all that we care about, and we will very much prefer not to merge a driver in the first place than to have to maintain it for 10y while it stands in our way and we don't have any real documentation or help.

So by making it "not weird" or "elegant" or whatever we can call it, you effectively remove any concern we might have about merging your driver, and there's only an upside (more hardware support and company involvement is good!). So you're making it easy for you too.

Maxime

#62 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Sui Jingfeng
kernel test robot noticed the following build warnings:

Hi Sui,

kernel test robot noticed the following build warnings:

[auto build test WARNING on drm-misc/drm-misc-next]
[also build test WARNING on linus/master v6.7-rc1 next-20231115] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Sui-Jingfeng/drm-bridge-it66121-Use-dev-replace-ctx-dev-in-the-it66121_probe/20231114-231203
base:   git://anongit.freedesktop.org/drm/drm-misc drm-misc-next
patch link:    https://lore.kernel.org/r/20231114150130.497915-9-sui.jingfeng%40linux.dev
patch subject: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib
config: x86_64-randconfig-005-20231115 (https://download.01.org/0day-ci/archive/20231115/[email protected]/config)
compiler: gcc-12 (Debian 12.2.0-14) 12.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20231115/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

All warnings (new ones prefixed by >>):

>> drivers/gpu/drm/bridge/ite-it66121.c:1654:5: warning: no previous prototype for 'it66121_create_bridge' [-Wmissing-prototypes]
    1654 | int it66121_create_bridge(struct i2c_client *client, bool of_support,
         |     ^~~~~~~~~~~~~~~~~~~~~
>> drivers/gpu/drm/bridge/ite-it66121.c:1752:6: warning: no previous prototype for 'it66121_destroy_bridge' [-Wmissing-prototypes]
    1752 | void it66121_destroy_bridge(struct drm_bridge *bridge)
         |      ^~~~~~~~~~~~~~~~~~~~~~

vim +/it66121_create_bridge +1654 drivers/gpu/drm/bridge/ite-it66121.c

1653

> 1654	int it66121_create_bridge(struct i2c_client *client, bool of_support,
  1655				  bool hpd_support, bool audio_support,
  1656				  struct drm_bridge **bridge)
  1657	{
  1658		struct device *dev = &client->dev;
  1659		int ret;
  1660		struct it66121_ctx *ctx;
  1661	
  1662		ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
  1663		if (!ctx)
  1664			return -ENOMEM;
  1665	
  1666		ctx->dev = dev;
  1667		ctx->client = client;
  1668		mutex_init(&ctx->lock);
  1669	
  1670		if (of_support) {
  1671			ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
  1672			if (ret)
  1673				return ret;
  1674	
  1675			ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
  1676			if (ret)
  1677				return ret;
  1678		} else {
  1679			ctx->bus_width = 24;
  1680			ctx->next_bridge = NULL;
  1681		}
  1682	
  1683		it66121_hw_reset(ctx);
  1684	
  1685		ctx->regmap = devm_regmap_init_i2c(client, &it66121_regmap_config);
  1686		if (IS_ERR(ctx->regmap))
  1687			return PTR_ERR(ctx->regmap);
  1688	
  1689		ret = it66121_read_chip_id(ctx, false);
  1690		if (ret)
  1691			return ret;
  1692	
  1693		ctx->info = it66121_get_match_data(ctx->vender_id, ctx->device_id);
  1694		if (!ctx->info)
  1695			return -ENODEV;
  1696	
  1697		if (hpd_support) {
  1698			ret = devm_request_threaded_irq(dev, client->irq, NULL,
  1699							it66121_irq_threaded_handler,
  1700							IRQF_ONESHOT, dev_name(dev),
  1701							ctx);
  1702			if (ret < 0) {
  1703				dev_err(dev, "Failed to request irq: %d\n", ret);
  1704				return ret;
  1705			}
  1706		}
  1707	
  1708		it66121_bridge_init_base(&ctx->bridge, dev->of_node, true);
  1709	
  1710		if (audio_support)
  1711			it66121_audio_codec_init(ctx, dev);
  1712	
  1713		*bridge = &ctx->bridge;
  1714	
  1715		dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
  1716			 ctx->vender_id, ctx->device_id, ctx->revision);
  1717	
  1718		return 0;
  1719	}
  1720	EXPORT_SYMBOL_GPL(it66121_create_bridge);
  1721	
  1722	static int it66121_probe(struct i2c_client *client)
  1723	{
  1724		struct device *dev = &client->dev;
  1725		struct it66121_ctx *ctx;
  1726		struct drm_bridge *bridge;
  1727		int ret;
  1728	
  1729		if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
  1730			dev_err(dev, "I2C check functionality failed.\n");
  1731			return -ENXIO;
  1732		}
  1733	
  1734		ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
  1735						     it66121_supplies);
  1736		if (ret) {
  1737			dev_err(dev, "Failed to enable power supplies\n");
  1738			return ret;
  1739		}
  1740	
  1741		ret = it66121_create_bridge(client, true, true, true, &bridge);
  1742		if (ret)
  1743			return ret;
  1744	
  1745		ctx = bridge_to_it66121(bridge);
  1746	
  1747		i2c_set_clientdata(client, ctx);
  1748	
  1749		return 0;
  1750	}
  1751	
> 1752	void it66121_destroy_bridge(struct drm_bridge *bridge)

1753 {
1754 struct it66121_ctx *ctx = bridge_to_it66121(bridge);
1755
1756 drm_bridge_remove(bridge);
1757
1758 mutex_destroy(&ctx->lock);
1759 }
1760 EXPORT_SYMBOL_GPL(it66121_destroy_bridge);
1761

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki
#63 lore raw

Re: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib

In reply to Sui Jingfeng
kernel test robot noticed the following build warnings:

Hi Sui,

kernel test robot noticed the following build warnings:

[auto build test WARNING on drm-misc/drm-misc-next]
[also build test WARNING on linus/master v6.7-rc2 next-20231120] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]

url:    https://github.com/intel-lab-lkp/linux/commits/Sui-Jingfeng/drm-bridge-it66121-Use-dev-replace-ctx-dev-in-the-it66121_probe/20231114-231203
base:   git://anongit.freedesktop.org/drm/drm-misc drm-misc-next
patch link:    https://lore.kernel.org/r/20231114150130.497915-9-sui.jingfeng%40linux.dev
patch subject: [PATCH 8/8] drm/bridge: it66121: Allow link this driver as a lib
config: x86_64-buildonly-randconfig-004-20231120 (https://download.01.org/0day-ci/archive/20231120/[email protected]/config)
compiler: clang version 16.0.4 (https://github.com/llvm/llvm-project.git ae42196bc493ffe877a7e3dff8be32035dea4d07)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20231120/[email protected]/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <[email protected]>
| Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/

All warnings (new ones prefixed by >>):

>> drivers/gpu/drm/bridge/ite-it66121.c:1654:5: warning: no previous prototype for function 'it66121_create_bridge' [-Wmissing-prototypes]
   int it66121_create_bridge(struct i2c_client *client, bool of_support,
       ^
   drivers/gpu/drm/bridge/ite-it66121.c:1654:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
   int it66121_create_bridge(struct i2c_client *client, bool of_support,
   ^
   static 
>> drivers/gpu/drm/bridge/ite-it66121.c:1752:6: warning: no previous prototype for function 'it66121_destroy_bridge' [-Wmissing-prototypes]
   void it66121_destroy_bridge(struct drm_bridge *bridge)
        ^

drivers/gpu/drm/bridge/ite-it66121.c:1752:1: note: declare 'static' if the function is not intended to be used outside of this translation unit void it66121_destroy_bridge(struct drm_bridge *bridge)
^
static
2 warnings generated.

vim +/it66121_create_bridge +1654 drivers/gpu/drm/bridge/ite-it66121.c

1653

> 1654	int it66121_create_bridge(struct i2c_client *client, bool of_support,
  1655				  bool hpd_support, bool audio_support,
  1656				  struct drm_bridge **bridge)
  1657	{
  1658		struct device *dev = &client->dev;
  1659		int ret;
  1660		struct it66121_ctx *ctx;
  1661	
  1662		ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
  1663		if (!ctx)
  1664			return -ENOMEM;
  1665	
  1666		ctx->dev = dev;
  1667		ctx->client = client;
  1668		mutex_init(&ctx->lock);
  1669	
  1670		if (of_support) {
  1671			ret = it66121_of_read_bus_width(dev, &ctx->bus_width);
  1672			if (ret)
  1673				return ret;
  1674	
  1675			ret = it66121_of_get_next_bridge(dev, &ctx->next_bridge);
  1676			if (ret)
  1677				return ret;
  1678		} else {
  1679			ctx->bus_width = 24;
  1680			ctx->next_bridge = NULL;
  1681		}
  1682	
  1683		it66121_hw_reset(ctx);
  1684	
  1685		ctx->regmap = devm_regmap_init_i2c(client, &it66121_regmap_config);
  1686		if (IS_ERR(ctx->regmap))
  1687			return PTR_ERR(ctx->regmap);
  1688	
  1689		ret = it66121_read_chip_id(ctx, false);
  1690		if (ret)
  1691			return ret;
  1692	
  1693		ctx->info = it66121_get_match_data(ctx->vender_id, ctx->device_id);
  1694		if (!ctx->info)
  1695			return -ENODEV;
  1696	
  1697		if (hpd_support) {
  1698			ret = devm_request_threaded_irq(dev, client->irq, NULL,
  1699							it66121_irq_threaded_handler,
  1700							IRQF_ONESHOT, dev_name(dev),
  1701							ctx);
  1702			if (ret < 0) {
  1703				dev_err(dev, "Failed to request irq: %d\n", ret);
  1704				return ret;
  1705			}
  1706		}
  1707	
  1708		it66121_bridge_init_base(&ctx->bridge, dev->of_node, true);
  1709	
  1710		if (audio_support)
  1711			it66121_audio_codec_init(ctx, dev);
  1712	
  1713		*bridge = &ctx->bridge;
  1714	
  1715		dev_info(dev, "IT66121 probed, chip id: 0x%x:0x%x, revision: %u\n",
  1716			 ctx->vender_id, ctx->device_id, ctx->revision);
  1717	
  1718		return 0;
  1719	}
  1720	EXPORT_SYMBOL_GPL(it66121_create_bridge);
  1721	
  1722	static int it66121_probe(struct i2c_client *client)
  1723	{
  1724		struct device *dev = &client->dev;
  1725		struct it66121_ctx *ctx;
  1726		struct drm_bridge *bridge;
  1727		int ret;
  1728	
  1729		if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
  1730			dev_err(dev, "I2C check functionality failed.\n");
  1731			return -ENXIO;
  1732		}
  1733	
  1734		ret = devm_regulator_bulk_get_enable(dev, ARRAY_SIZE(it66121_supplies),
  1735						     it66121_supplies);
  1736		if (ret) {
  1737			dev_err(dev, "Failed to enable power supplies\n");
  1738			return ret;
  1739		}
  1740	
  1741		ret = it66121_create_bridge(client, true, true, true, &bridge);
  1742		if (ret)
  1743			return ret;
  1744	
  1745		ctx = bridge_to_it66121(bridge);
  1746	
  1747		i2c_set_clientdata(client, ctx);
  1748	
  1749		return 0;
  1750	}
  1751	
> 1752	void it66121_destroy_bridge(struct drm_bridge *bridge)

1753 {
1754 struct it66121_ctx *ctx = bridge_to_it66121(bridge);
1755
1756 drm_bridge_remove(bridge);
1757
1758 mutex_destroy(&ctx->lock);
1759 }
1760 EXPORT_SYMBOL_GPL(it66121_destroy_bridge);
1761

Signature · 2 lines
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki