Skip to contentSkip to conversation

Compactflash (Sandisk 512) hangs on access

DISCUSSION Prashant Viswanathan 2 participants 4 messages Jan 27, 2005 – Feb 3, 2005

lore
Share & tools
lore
#0 lore raw

I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).

I use a CF->IDE adapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open /dev/hdc".

I have looked at newsgroups and tried the following things
* Used another CF (same brand) to make sure it wasn't due to a bad CF. Moreover I can access it perfectly well using a USB flash
reader/writer (shows up as a SCSI disk).
* Tried a compactflash from another manufacturer.
* Upgraded my Linux kernel from 2.4.26 to 2.6.7
* Disabled DMA on the IDE drive using hdparm
* Built and used kernels with and without devfs.
* Used compactflash as a slave on the IDE channel, as a master and on both primary and secondary channels.

I get errors like (from dmesg)
"hdc: irq timeout: status=0xff { Busy }" (no dma)
or
"hdc: lost interrupt" (when i had dma enabled)

Is there some nasty race condition that I am hitting?

Also, now I can't seem to turn dma back on.

<snip>
everest root # hdparm -d1 /dev/hdc

/dev/hdc:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
</snip>

I would appreciate any help/suggestions/pointers.

Thanks a lot in advance for reading through this and any help. Prashant

P.S Please CC me on the responses.

#1 lore raw

Have you checked that the power connector really provides 5V to the IDE-CF adapter ? I had the exact same behaviour 5 years ago with a power wire cut. Signal lines were powerful enough to bring power to the cheap flash (16 MB), I could even read it, most times. The kernel almost always booted from it, and when it turned to mount the ext2 fs R/W, it hanged. I finally partially destroyed it this way, and it got several defects which could not be cleaned with a simple write or format.

Other than that, I have lots of CF cards on IDE adapters (some on motherboard, some hand-made, some bought to serious makers), and never ran into such problems since.

Willy

Quoted 54 lines · Prashant Viswanathan

I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).

I use a CF->IDE adapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open /dev/hdc".

I have looked at newsgroups and tried the following things
* Used another CF (same brand) to make sure it wasn't due to a bad CF. Moreover I can access it perfectly well using a USB flash
reader/writer (shows up as a SCSI disk).
* Tried a compactflash from another manufacturer.
* Upgraded my Linux kernel from 2.4.26 to 2.6.7
* Disabled DMA on the IDE drive using hdparm
* Built and used kernels with and without devfs.
* Used compactflash as a slave on the IDE channel, as a master and on both primary and secondary channels.

I get errors like (from dmesg)
"hdc: irq timeout: status=0xff { Busy }" (no dma)
or
"hdc: lost interrupt" (when i had dma enabled)

Is there some nasty race condition that I am hitting?

Also, now I can't seem to turn dma back on.

<snip>
everest root # hdparm -d1 /dev/hdc

/dev/hdc:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
</snip>

I would appreciate any help/suggestions/pointers.

Thanks a lot in advance for reading through this and any help. Prashant

P.S Please CC me on the responses.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#2 lore raw
Quoted 11 lines
Quoted 11 lines

I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).

I use a CF->IDE adapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open /dev/hdc".

Quoted 8 lines · Willy Tarreau

Have you checked that the power connector really provides 5V to the IDE-CF adapter ? I had the exact same behaviour 5 years ago with a power wire cut. Signal lines were powerful enough to bring power to the cheap flash (16 MB), I could even read it, most times. The kernel almost always booted from it, and when it turned to mount the ext2 fs R/W, it hanged. I finally partially destroyed it this way, and it got several defects which could not be cleaned with a simple write or format.

Quoted 5 lines

Other than that, I have lots of CF cards on IDE adapters (some on motherboard, some hand-made, some bought to serious makers), and never ran into such problems since.

Willy

The power connector is fine.

I also disabled DMA (some suggestion on this newsgroup to a similar error) and now I can't turn it back on.

<snip>
everest root # hdparm -d1 /dev/hdc

/dev/hdc:
setting using_dma to 1 (on)

#3 lore raw
Quoted 29 lines · Prashant Viswanathan
Quoted 11 lines
Quoted 11 lines

I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).

I use a CF->IDE adapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open /dev/hdc".

Quoted 8 lines · Willy Tarreau

Have you checked that the power connector really provides 5V to the IDE-CF adapter ? I had the exact same behaviour 5 years ago with a power wire cut. Signal lines were powerful enough to bring power to the cheap flash (16 MB), I could even read it, most times. The kernel almost always booted from it, and when it turned to mount the ext2 fs R/W, it hanged. I finally partially destroyed it this way, and it got several defects which could not be cleaned with a simple write or format.

Quoted 5 lines

Other than that, I have lots of CF cards on IDE adapters (some on motherboard, some hand-made, some bought to serious makers), and never ran into such problems since.

Willy

The power connector is fine.

Quoted 9 lines

I also disabled DMA (some suggestion on this newsgroup to a similar error) and now I can't turn it back on.

<snip>
everest root # hdparm -d1 /dev/hdc

/dev/hdc:
setting using_dma to 1 (on)

Finally figured out the problem (or at least worked around it). Everything seems to work perfectly after I switched to an older 40 conductor IDE cable! Before that I was using the newer 80 conductor IDE cable. I sitll dont understand why the newer ( and apparently better) cables are problematic. Higher speeds causing race conditions perhaps?