Compactflash (Sandisk 512) hangs on access
I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).
I use a CF->IDE adapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open /dev/hdc".
I have looked at newsgroups and tried the following things
* Used another CF (same brand) to make sure it wasn't due to a bad CF. Moreover I can access it perfectly well using a USB flash
reader/writer (shows up as a SCSI disk).
* Tried a compactflash from another manufacturer.
* Upgraded my Linux kernel from 2.4.26 to 2.6.7
* Disabled DMA on the IDE drive using hdparm
* Built and used kernels with and without devfs.
* Used compactflash as a slave on the IDE channel, as a master and on both primary and secondary channels.
I get errors like (from dmesg)
"hdc: irq timeout: status=0xff { Busy }" (no dma)
or
"hdc: lost interrupt" (when i had dma enabled)
Is there some nasty race condition that I am hitting?
Also, now I can't seem to turn dma back on.
<snip>
everest root # hdparm -d1 /dev/hdc
/dev/hdc:
setting using_dma to 1 (on)HDIO_SET_DMA failed: Operation not permittedusing_dma = 0 (off)
</snip>
I would appreciate any help/suggestions/pointers.
Thanks a lot in advance for reading through this and any help. Prashant
P.S Please CC me on the responses.
Have you checked that the power connector really provides 5V to the IDE-CF adapter ? I had the exact same behaviour 5 years ago with a power wire cut. Signal lines were powerful enough to bring power to the cheap flash (16 MB), I could even read it, most times. The kernel almost always booted from it, and when it turned to mount the ext2 fs R/W, it hanged. I finally partially destroyed it this way, and it got several defects which could not be cleaned with a simple write or format.
Other than that, I have lots of CF cards on IDE adapters (some on motherboard, some hand-made, some bought to serious makers), and never ran into such problems since.
Willy
Quoted 54 lines · Prashant Viswanathan
I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).
I use a
CF->IDEadapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open/dev/hdc".I have looked at newsgroups and tried the following things
* Used another CF (same brand) to make sure it wasn't due to a bad CF. Moreover I can access it perfectly well using a USB flash
reader/writer (shows up as a SCSI disk).
* Tried a compactflash from another manufacturer.
* Upgraded my Linux kernel from 2.4.26 to 2.6.7
* Disabled DMA on the IDE drive using hdparm
* Built and used kernels with and without devfs.
* Used compactflash as a slave on the IDE channel, as a master and on both primary and secondary channels.I get errors like (from dmesg)
"hdc: irq timeout: status=0xff { Busy }" (no dma)
or
"hdc: lost interrupt" (when i had dma enabled)Is there some nasty race condition that I am hitting?
Also, now I can't seem to turn dma back on.
<snip>
everest root # hdparm -d1/dev/hdc
/dev/hdc:
settingusing_dmato 1 (on)HDIO_SET_DMAfailed: Operation not permittedusing_dma= 0 (off)
</snip>I would appreciate any help/suggestions/pointers.
Thanks a lot in advance for reading through this and any help. Prashant
P.SPlease CC me on the responses.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 11 lines
Quoted 11 lines
I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).
I use a
CF->IDEadapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open/dev/hdc".
Quoted 8 lines · Willy Tarreau
Have you checked that the power connector really provides 5V to the IDE-CF adapter ? I had the exact same behaviour 5 years ago with a power wire cut. Signal lines were powerful enough to bring power to the cheap flash (16 MB), I could even read it, most times. The kernel almost always booted from it, and when it turned to mount the ext2 fs R/W, it hanged. I finally partially destroyed it this way, and it got several defects which could not be cleaned with a simple write or format.
Quoted 5 lines
Other than that, I have lots of CF cards on IDE adapters (some on motherboard, some hand-made, some bought to serious makers), and never ran into such problems since.
Willy
The power connector is fine.
I also disabled DMA (some suggestion on this newsgroup to a similar error) and now I can't turn it back on.
<snip>
everest root # hdparm -d1 /dev/hdc
/dev/hdc:
setting using_dma to 1 (on)
Quoted 29 lines · Prashant Viswanathan
Quoted 11 lines
Quoted 11 lines
I have been trying unsuccessfully over the last 2 weeks to get compactflash working on my Linux system based on mini-ITX (Via CL motherboard, pentium compatible).
I use a
CF->IDEadapter to access it just like a IDE hard disk. My compactflash is Sandisk SDCFH-512. Linux can detect it. I can even mount it and do a fdisk on it. However, the moment I try to do anything substantial like copy multiple files or copy 1000 blocks using dd, I lose access to it. Linux loses access to it totally. I can't even do a fdisk on it. I get an error like "Unable to open/dev/hdc".Quoted 8 lines · Willy Tarreau
Have you checked that the power connector really provides 5V to the IDE-CF adapter ? I had the exact same behaviour 5 years ago with a power wire cut. Signal lines were powerful enough to bring power to the cheap flash (16 MB), I could even read it, most times. The kernel almost always booted from it, and when it turned to mount the ext2 fs R/W, it hanged. I finally partially destroyed it this way, and it got several defects which could not be cleaned with a simple write or format.
Quoted 5 lines
Other than that, I have lots of CF cards on IDE adapters (some on motherboard, some hand-made, some bought to serious makers), and never ran into such problems since.
Willy
The power connector is fine.
Quoted 9 lines
I also disabled DMA (some suggestion on this newsgroup to a similar error) and now I can't turn it back on.
<snip>
everest root # hdparm -d1/dev/hdc
/dev/hdc:
settingusing_dmato 1 (on)
Finally figured out the problem (or at least worked around it). Everything seems to work perfectly after I switched to an older 40 conductor IDE cable! Before that I was using the newer 80 conductor IDE cable. I sitll dont understand why the newer ( and apparently better) cables are problematic. Higher speeds causing race conditions perhaps?