Skip to contentSkip to conversation

Compaq diskarray problems

linux-lvm Jörgen Winqvist 4 participants 5 messages Oct 10, 2000 – Oct 19, 2000 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

Hi,

I can't pvcreate LUN's on a Compaq raid controller. This LUN is 10 Gb. I've compiled 8.0final.
(I had to comment #include "gnu/types.h" out in liblvm.h).

Greateful for any help.

Regards

J�rgen

Compaq Proliant DL380 with 3 striped disks and 5 LUNs' Redhat 7 with 2.4.0-0.26
----------------------------------------------------------------

# cat /proc/lvm
LVM driver version 0.8final  (15/02/2000)
Total:  0 VGs  0 PVs  0 LVs (0 LVs open)
Global: 143 bytes malloced   IOP version: 6   5:20:33 active

-------------------------------------------------------------

# fdisk /dev/ida/c0d1
Command (m for help): p
Disk /dev/ida/c0d1: 255 heads, 32 sectors, 2510 cylinders
Units = cylinders of 8160 * 512 bytes

Device Boot Start End Blocks Id System

Command (m for help): q

# pvcreate  /dev/ida/c0d1
pvcreate -- invalid partition type 0x83 for "/dev/ida/c0d1" (must be
0x8e)
--------------------------------------------------------------

I've now added a partition with type LVM

# fdisk /dev/ida/c0d1
Command (m for help): p
Disk /dev/ida/c0d1: 255 heads, 32 sectors, 2510 cylinders
Units = cylinders of 8160 * 512 bytes
         Device Boot    Start       End    Blocks   Id  System
/dev/ida/c0d1p1             1      2510  10240784   8e  Linux LVM
Command (m for help): q
# pvcreate  /dev/ida/c0d1p
pvcreate -- invalid partition type 0x83 for "/dev/ida/c0d1p1" (must be
0x8e)
--------------------------------------------------------------

output from dmesg

cpqarray: Device 1000 has been found at 0 8 Compaq SMART2 Driver (v 2.4.0)
Found 1 controller(s)
cpqarray: Finding drives on ida0 (Integrated Array) cpqarray ida/c0d0: blksz=512 nr_blks=20481600 cpqarray ida/c0d1: blksz=512 nr_blks=20481600 cpqarray ida/c0d2: blksz=512 nr_blks=20481600 cpqarray ida/c0d3: blksz=512 nr_blks=20481600 cpqarray ida/c0d4: blksz=512 nr_blks=24732960
cpqarray: Starting firmware's background processing Partition check:
ida/c0d0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 > ida/c0d1:
ida/c0d2:
ida/c0d3:
ida/c0d4:
---------------------------------------------------------------

A message that is not in the archive (sent off-list or not yet received): [email protected]

#2 lore raw

Justin

I did try that to begin with. Look further down my posting. Pvcreate complains on the partition type whatever i change it to. It always says it has 0x83.

J�rgen

Quoted 77 lines · Justin Hamilton

Within fdisk, you need to select option t (to change the type of the partition) and select 8e for the type.

Your pvcreate should work just fine after this.

Justin

Quoted 69 lines · J�rgen Winqvist

Hi,

I can't pvcreate LUN's on a Compaq raid controller. This LUN is 10 Gb. I've compiled 8.0final.
(I had to comment #include "gnu/types.h" out in liblvm.h).

Greateful for any help.

Regards

J�rgen

Compaq Proliant DL380 with 3 striped disks and 5 LUNs' Redhat 7 with 2.4.0-0.26
----------------------------------------------------------------

# cat /proc/lvm
LVM driver version 0.8final  (15/02/2000)
Total:  0 VGs  0 PVs  0 LVs (0 LVs open)
Global: 143 bytes malloced   IOP version: 6   5:20:33 active

-------------------------------------------------------------

# fdisk /dev/ida/c0d1
Command (m for help): p
Disk /dev/ida/c0d1: 255 heads, 32 sectors, 2510 cylinders
Units = cylinders of 8160 * 512 bytes

Device Boot Start End Blocks Id System

Command (m for help): q

# pvcreate  /dev/ida/c0d1
pvcreate -- invalid partition type 0x83 for "/dev/ida/c0d1" (must be
0x8e)
--------------------------------------------------------------

I've now added a partition with type LVM

# fdisk /dev/ida/c0d1
Command (m for help): p
Disk /dev/ida/c0d1: 255 heads, 32 sectors, 2510 cylinders
Units = cylinders of 8160 * 512 bytes
         Device Boot    Start       End    Blocks   Id  System
/dev/ida/c0d1p1             1      2510  10240784   8e  Linux LVM
Command (m for help): q
# pvcreate  /dev/ida/c0d1p
pvcreate -- invalid partition type 0x83 for "/dev/ida/c0d1p1" (must be
0x8e)
--------------------------------------------------------------

output from dmesg

cpqarray: Device 1000 has been found at 0 8 Compaq SMART2 Driver (v 2.4.0)
Found 1 controller(s)
cpqarray: Finding drives on ida0 (Integrated Array) cpqarray ida/c0d0: blksz=512 nr_blks=20481600 cpqarray ida/c0d1: blksz=512 nr_blks=20481600 cpqarray ida/c0d2: blksz=512 nr_blks=20481600 cpqarray ida/c0d3: blksz=512 nr_blks=20481600 cpqarray ida/c0d4: blksz=512 nr_blks=24732960
cpqarray: Starting firmware's background processing Partition check:
ida/c0d0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 > ida/c0d1:
ida/c0d2:
ida/c0d3:
ida/c0d4:
---------------------------------------------------------------

#3 lore raw
In reply to Jörgen Winqvist

Jorgen Winqvist, you write:

Quoted 5 lines

I can't pvcreate LUN's on a Compaq raid controller. This LUN is 10 Gb. I've compiled 8.0final.
(I had to comment #include "gnu/types.h" out in liblvm.h).

Greateful for any help.

Try the updated lvm tools (SRPM) at:

ftp://ftp.stelias.com/pub/adilger/

This includes a number of patches to the 0.8 final tools that were posted on this list, but are not in the "official" tools.

Cheers, Andreas

#4 lore raw

[linux-lvm] Thanks! and Swap on LVM?

Quoted 3 lines · Andreas Dilger

Try the updated lvm tools (SRPM) at:

ftp://ftp.stelias.com/pub/adilger/

Thank you!!! I usually stay away from SRPM's, but now that I've got alien, it's not so bad. 'alien --to-tgz' is a dream. A plus side to all of this, my pvscan no longer segfaults! ;-) Neither does my vgscan! ;-) I was actually going to sit down with gdb tonight and do some backtracing when I saw your update. Very nice to have a 1:00 in the morning. ;-) Again, thanks!

OH. I've noticed a problem as of late. While trying lvm on both the 2.4.0-test9 and 2.2.17, I have not been able to use an lv device as a swap device. The computer starts acting like it's got bad memory and segfaults during compile time, most notably during kernel compiles.

Has anyone successfully used a lv parition as a swap device???

{good thing I had an extra HD}

Signature · 2 lines
  Chad "^chewie, gunnarr" Walstrom <[email protected]>
              http://wookimus.net/chewie
#5 lore raw

Re: [linux-lvm] Thanks! and Swap on LVM?

Quoted 7 lines · ^chewie
Quoted 3 lines · Andreas Dilger

Try the updated lvm tools (SRPM) at:

ftp://ftp.stelias.com/pub/adilger/

Thank you!!! I usually stay away from SRPM's, but now that I've got alien, it's not so bad. 'alien --to-tgz' is a dream. A plus side to

also dd | gzip -dc | cpio :)))))

....

Quoted 3 lines

Has anyone successfully used a lv parition as a swap device???

[pts/5]bluca@Moskowskaya:~% uname -a
Linux Moskowskaya 2.4.0-test8 #1 Sun Sep 10 09:48:24 CEST 2000 i586 unknown [pts/5]bluca@Moskowskaya:~% swapon -s

Filename                        Type            Size    Used    Priority
/dev/vg01/lvol2                 partition       262136  29416   -1

L.

Signature · 2 lines
Luca Berra -- [email protected]
    Communication Media & Services S.r.l.