Skip to contentSkip to conversation

Only 5 undocumented configuration symbols left

DISCUSSION Eric S. Raymond 4 participants 4 messages May 30, 2001 – May 31, 2001

lore
Share & tools
lore
#0 lore raw

The current list of symbols with missing help is very short. Here it is:

PPC port:

CONFIG_BLK_DEV_MPC8xx_IDE
CONFIG_IRQ_ALL_CPUS
CONFIG_USE_MDIO

CRIS port:

CONFIG_ETRAX_FLASH_BUSWIDTH
CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C

Let's finish this off, people!

Signature · 5 lines
		<a href="http://www.tuxedo.org/~esr/">Eric S. Raymond</a>

The people cannot delegate to government the power to do anything
which would be unlawful for them to do themselves.
	-- John Locke, "A Treatise Concerning Civil Government"
#1 lore raw
Quoted 2 lines · Eric S. Raymond

CONFIG_ETRAX_FLASH_BUSWIDTH
CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C

05/31 10:11:20 renamed from 05/08 14:22:21 1.24 +12 -0
@@ -17564,6 +17564,10 @@
 CONFIG_ETRAX_DRAM_SIZE
   Size of DRAM (decimal in MB) typically 2, 8 or 16.
 
+ETRAX Flash Memory configuration
+CONFIG_ETRAX_FLASH_BUSWIDTH
+  Width in bytes of the Flash bus (1, 2 or 4). Is usually 2.
+
 LED configuration on PA
 CONFIG_ETRAX_PA_LEDS
   The Etrax network driver is responsible for flashing LED's when
@@ -17991,6 +17995,14 @@
        ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_WRITEREG), i2c_arg);
        i2c_arg = I2C_READARG(STA013_READ_ADDR, reg);
        val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg);
+
+Etrax100 I2C configuration
+CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C
+  Select whether to use the special I2C mode in the PB I/O register or
+  not. This option needs to be selected in order to use some drivers that
+  accesses the I2C I/O pins directly instead of going through the I2C
+  driver, like the DS1302 realtime-clock driver. If you are uncertain, 
+  choose yes here.
 
 Etrax100 I2C EEPROM (NVRAM) support
 CONFIG_ETRAX_I2C_EEPROM
#2 lore raw

Since I don't actually know what you're talking about, I'll just make picky little comments about the grammar, etc. ;)

05/31 10:11:20 line 18003

Quoted 5 lines · On Thu, 31 May 2001 12:14:06 +0200 (CEST) Bjorn Wesen <[email protected]>…
05/31 10:11:20 renamed from 05/08 14:22:21 1.24 +5 -0
+Etrax100 I2C configuration
+CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C
+  Select whether to use the special I2C mode in the PB I/O register or
+  not. This option needs to be selected in order to use some drivers that
+  accesses the I2C I/O pins directly instead of going through the I2C
     ^^^^^^^^
     access

05/31 10:11:20 line 18005

Quoted 2 lines
05/31 10:11:20 renamed from 05/08 14:22:21 1.24 +2 -0
+  driver, like the DS1302 realtime-clock driver. If you are uncertain, 
+  choose yes here.
     ^^^^^^^^^^^^^^^

This is usually "say Y here." Minor, I know, but it'd be nice to get the nomenclature standardized.

(Actually, "...to be selected in order to use some drivers, such as the DS1302 realtime clock driver, that access the I2C I/O pins directly instead of going through the I2C driver." might scan better.)

Bruce

#3 lore raw
In reply to Eric S. Raymond
Quoted 6 lines · Eric S. Raymond

The current list of symbols with missing help is very short. Here it is:

PPC port:

CONFIG_IRQ_ALL_CPUS

This option gives the kernel permission to distribute IRQs across multiple CPUs. Saying N here will route all IRQs to the first CPU. Generally SMP PowerMacs can answer Y. SMP IBM CHRP boxes or Power3 boxes should say N for now.

Regards,

Tom

Signature · 6 lines
Tom Gall - PPC64                 "Where's the ka-boom? There was
Linux Technology Center           supposed to be an earth
(w) [email protected]         shattering ka-boom!"
(w) 507-253-4558                 -- Marvin Martian
(h) [email protected]
http://www.ibm.com/linux/ltc/projects/ppc