Only 5 undocumented configuration symbols left
The current list of symbols with missing help is very short. Here it is:
PPC port:
CONFIG_BLK_DEV_MPC8xx_IDECONFIG_IRQ_ALL_CPUSCONFIG_USE_MDIO
CRIS port:
CONFIG_ETRAX_FLASH_BUSWIDTHCONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C
Let's finish this off, people!
Signature · 5 lines
<a href="http://www.tuxedo.org/~esr/">Eric S. Raymond</a> The people cannot delegate to government the power to do anything which would be unlawful for them to do themselves. -- John Locke, "A Treatise Concerning Civil Government"
Quoted 2 lines · Eric S. Raymond
CONFIG_ETRAX_FLASH_BUSWIDTHCONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C
05/31 10:11:20 renamed from 05/08 14:22:21 1.24 +12 -0
@@ -17564,6 +17564,10 @@ CONFIG_ETRAX_DRAM_SIZE Size of DRAM (decimal in MB) typically 2, 8 or 16. +ETRAX Flash Memory configuration +CONFIG_ETRAX_FLASH_BUSWIDTH + Width in bytes of the Flash bus (1, 2 or 4). Is usually 2. + LED configuration on PA CONFIG_ETRAX_PA_LEDS The Etrax network driver is responsible for flashing LED's when
@@ -17991,6 +17995,14 @@ ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_WRITEREG), i2c_arg); i2c_arg = I2C_READARG(STA013_READ_ADDR, reg); val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg); + +Etrax100 I2C configuration +CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C + Select whether to use the special I2C mode in the PB I/O register or + not. This option needs to be selected in order to use some drivers that + accesses the I2C I/O pins directly instead of going through the I2C + driver, like the DS1302 realtime-clock driver. If you are uncertain, + choose yes here. Etrax100 I2C EEPROM (NVRAM) support CONFIG_ETRAX_I2C_EEPROM
Since I don't actually know what you're talking about, I'll just make picky little comments about the grammar, etc. ;)
05/31 10:11:20 line 18003
Quoted 5 lines · On Thu, 31 May 2001 12:14:06 +0200 (CEST) Bjorn Wesen <[email protected]>…
05/31 10:11:20 renamed from 05/08 14:22:21 1.24 +5
-0+Etrax100 I2C configuration +CONFIG_ETRAX_I2C_USES_PB_NOT_PB_I2C + Select whether to use the special I2C mode in the PB I/O register or + not. This option needs to be selected in order to use some drivers that + accesses the I2C I/O pins directly instead of going through the I2C
^^^^^^^^
access05/31 10:11:20 line 18005
Quoted 2 lines
05/31 10:11:20 renamed from 05/08 14:22:21 1.24 +2
-0+ driver, like the DS1302 realtime-clock driver. If you are uncertain, + choose yes here.
^^^^^^^^^^^^^^^
This is usually "say Y here." Minor, I know, but it'd be nice to get the nomenclature standardized.
(Actually, "...to be selected in order to use some drivers, such as the DS1302 realtime clock driver, that access the I2C I/O pins directly instead of going through the I2C driver." might scan better.)
Bruce
Quoted 6 lines · Eric S. Raymond
The current list of symbols with missing help is very short. Here it is:
PPC port:
CONFIG_IRQ_ALL_CPUS
This option gives the kernel permission to distribute IRQs across multiple CPUs. Saying N here will route all IRQs to the first CPU. Generally SMP PowerMacs can answer Y. SMP IBM CHRP boxes or Power3 boxes should say N for now.
Regards,
Tom
Signature · 6 lines
Tom Gall - PPC64 "Where's the ka-boom? There was Linux Technology Center supposed to be an earth (w) [email protected] shattering ka-boom!" (w) 507-253-4558 -- Marvin Martian (h) [email protected] http://www.ibm.com/linux/ltc/projects/ppc