Skip to contentSkip to conversation

How to debug PCI issues?

DISCUSSION Ben Greear 3 participants 3 messages Sep 28, 2001

lore
Share & tools
lore

Ben Greear

author
#0 lore raw

I'm working with a TYAN Tomcat board (i815, Ghz CPU). It's in a 1U machine with a butterfly riser so that I get two riser connections to one PCI slot. When I put Intel EEPRO nics in each slot, I can pass 30Mbps of traffic on each NIC without dropping a single packet (In two days of running).

If I run 20Mbps on one of the DLINK ports, I'm fine, but if I run 10Mbps on two of the DLINK ports, I start seeing dropped packets on every interface, and port errors like RX-FIFO.

So, I'm thinking that the DLINK NIC must be screwing up the PCI bus somehow when more than one of it's interfaces is passing any significant traffic. I have been able to run 10Mbps on all 8 ports of two DLINKs on an Intel EEA2 (i815) board, so I suspect the MB.

Does anyone have any ideas how to go about trouble-shooting this farther?

Thanks,
Ben

Signature · 3 lines
Ben Greear <[email protected]>          <[email protected]>
President of Candela Technologies Inc      http://www.candelatech.com
ScryMUD:  http://scry.wanfear.com     http://scry.wanfear.com/~greear
#1 lore raw

Ben Greear <[email protected]> :
[...]

Quoted 7 lines

So, I'm thinking that the DLINK NIC must be screwing up the PCI bus somehow when more than one of it's interfaces is passing any significant traffic. I have been able to run 10Mbps on all 8 ports of two DLINKs on an Intel EEA2 (i815) board, so I suspect the MB.

Does anyone have any ideas how to go about trouble-shooting this farther?

Check the pci latency timer settings for the devices are the same on the two mobos and force them with setpci if they aren't.

Signature · 1 line
Ueimor
#2 lore raw
In reply to Ben Greear
Quoted 9 lines · Ben Greear

I'm working with a TYAN Tomcat board (i815, Ghz CPU). It's in a 1U machine with a butterfly riser so that I get two riser connections to one PCI slot. When I put Intel EEPRO nics in each slot, I can pass 30Mbps of traffic on each NIC without dropping a single packet (In two days of running).

If I run 20Mbps on one of the DLINK ports, I'm fine, but if I run 10Mbps on two of the DLINK ports, I start seeing dropped packets on every interface, and port errors like RX-FIFO.

If I run traffic out one port I can get 100Mbit but if I try it with two ports at the same time I cet about 20Mbit per port at best. And I also get a _lot_ of errors but mostly carrier-errors.

Quoted 5 lines

So, I'm thinking that the DLINK NIC must be screwing up the PCI bus somehow when more than one of it's interfaces is passing any significant traffic. I have been able to run 10Mbps on all 8 ports of two DLINKs on an Intel EEA2 (i815) board, so I suspect the MB.

Quoted 16 lines

Does anyone have any ideas how to go about trouble-shooting this farther?

Thanks,
Ben

Signature · 8 lines
Ben Greear <[email protected]>          <[email protected]>
President of Candela Technologies Inc      http://www.candelatech.com
ScryMUD:  http://scry.wanfear.com     http://scry.wanfear.com/~greear
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

/Martin

Never argue with an idiot. They drag you down to their level, then beat you with experience.