How to debug PCI issues?
I'm working with a TYAN Tomcat board (i815, Ghz CPU). It's in a 1U machine with a butterfly riser so that I get two riser connections to one PCI slot. When I put Intel EEPRO nics in each slot, I can pass 30Mbps of traffic on each NIC without dropping a single packet (In two days of running).
If I run 20Mbps on one of the DLINK ports, I'm fine, but if I run 10Mbps on two of the DLINK ports, I start seeing dropped packets on every interface, and port errors like RX-FIFO.
So, I'm thinking that the DLINK NIC must be screwing up the PCI bus somehow when more than one of it's interfaces is passing any significant traffic. I have been able to run 10Mbps on all 8 ports of two DLINKs on an Intel EEA2 (i815) board, so I suspect the MB.
Does anyone have any ideas how to go about trouble-shooting this farther?
Thanks,
Ben
Signature · 3 lines
Ben Greear <[email protected]> <[email protected]> President of Candela Technologies Inc http://www.candelatech.com ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear
Ben Greear <[email protected]> :
[...]
Quoted 7 lines
So, I'm thinking that the DLINK NIC must be screwing up the PCI bus somehow when more than one of it's interfaces is passing any significant traffic. I have been able to run 10Mbps on all 8 ports of two DLINKs on an Intel EEA2 (i815) board, so I suspect the MB.
Does anyone have any ideas how to go about trouble-shooting this farther?
Check the pci latency timer settings for the devices are the same on the two mobos and force them with setpci if they aren't.
Signature · 1 line
Ueimor
Quoted 9 lines · Ben Greear
I'm working with a TYAN Tomcat board (i815, Ghz CPU). It's in a 1U machine with a butterfly riser so that I get two riser connections to one PCI slot. When I put Intel EEPRO nics in each slot, I can pass 30Mbps of traffic on each NIC without dropping a single packet (In two days of running).
If I run 20Mbps on one of the DLINK ports, I'm fine, but if I run 10Mbps on two of the DLINK ports, I start seeing dropped packets on every interface, and port errors like RX-FIFO.
If I run traffic out one port I can get 100Mbit but if I try it with two ports at the same time I cet about 20Mbit per port at best. And I also get a _lot_ of errors but mostly carrier-errors.
Quoted 5 lines
So, I'm thinking that the DLINK NIC must be screwing up the PCI bus somehow when more than one of it's interfaces is passing any significant traffic. I have been able to run 10Mbps on all 8 ports of two DLINKs on an Intel EEA2 (i815) board, so I suspect the MB.
Quoted 16 lines
Does anyone have any ideas how to go about trouble-shooting this farther?
Thanks,
BenSignature · 8 lines
Ben Greear <[email protected]> <[email protected]> President of Candela Technologies Inc http://www.candelatech.com ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
/Martin
Never argue with an idiot. They drag you down to their level, then beat you with experience.