Put XHCI controllers into D3 at S4/S5
Subsystems (2)
cover Put XHCI controllers into D3 at S4/S5
From: Mario Limonciello <[email protected]>
When the system is put into S4 or S5 XHCI controllers remain in D0. This causes higher power consumption and may compromise energy certifications. Consequently some systems consume more power in S5 than s0i3.
This affects all PCIe devices, but looking at breakdowns XHCI is the biggest offender for power consumption.
This series checks if any wakeups are needed and puts controllers into D3 if no wakeup necessary.
This series is a spiritual successor to [1] which aimed to do this more generally in PCI. It also accomplishes similar goals as [2], but aims for both S4 and S5.
[1] https://lore.kernel.org/linux-pci/[email protected]/#t
[2] https://lore.kernel.org/linux-pci/[email protected]/T/
Mario Limonciello (2):
xhci: pci: If no ports have wakeup enabled then disable PCI device at
S4
xhci: pci: Put XHCI controllers into D3hot at shutdown
drivers/usb/host/xhci-pci.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)
Signature · 1 line
2.43.0
PATCH 1/2 xhci: pci: If no ports have wakeup enabled then disable PCI device at S4
From: Mario Limonciello <[email protected]>
If a port on an XHCI controller hasn't been marked for wakeup at S4, then leaving it at D0 will needlessly consume power than necessary.
Explicitly check ports configured for wakeup and if none are found then put the controller into D3hot before hibernate.
--- drivers/usb/host/xhci-pci.c | 9 +++++++++ 1 file changed, 9 insertions(+)
drivers/usb/host/xhci-pci.c +9 -0
@@ -823,6 +823,7 @@ static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup)struct usb_device *udev;u32 portsc;int i; +bool wakeup = false;/* * Systems with XHCI_RESET_TO_DEFAULT quirk have boot firmware that
@@ -860,6 +861,14 @@ static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup) port->rhub->hcd->self.busnum, port->hcd_portnum + 1); portsc =xhci_port_state_to_neutral (portsc);writel (portsc |PORT_PE , port->addr); + wakeup = true; + } + +if (!wakeup) { +struct pci_dev *pdev =to_pci_dev (hcd->self.controller); + +xhci_shutdown (hcd); +pci_set_power_state (pdev, PCI_D3hot); }return 0 ;
Signature · 1 line
2.43.0
Re: [PATCH 1/2] xhci: pci: If no ports have wakeup enabled then disable PCI device at S4
Quoted 27 lines · On 12.7.2024 21.54, [email protected] wrote:
From: Mario Limonciello <[email protected]>
If a port on an XHCI controller hasn't been marked for wakeup at S4, then leaving it at D0 will needlessly consume power than necessary.
Explicitly check ports configured for wakeup and if none are found then put the controller into D3hot before hibernate.
Signed-off-by Mario Limonciello <[email protected]>--- drivers/usb/host/xhci-pci.c | 9 +++++++++ 1 file changed, 9 insertions(+)drivers/usb/host/xhci-pci.c +1
-0@@ -823,6 +823,7 @@ static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup)struct usb_device *udev;u32 portsc;int i; +bool wakeup = false;/* * Systems with XHCI_RESET_TO_DEFAULT quirk have boot firmware that @@ -860,6 +861,14 @@ static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup) port->rhub->hcd->self.busnum, port->hcd_portnum + 1);
drivers/usb/host/xhci-pci.c static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup) · line 871
Quoted 10 lines
drivers/usb/host/xhci-pci.c +8
-0portsc =xhci_port_state_to_neutral (portsc);writel (portsc |PORT_PE , port->addr); + wakeup = true; + } + +if (!wakeup) { +struct pci_dev *pdev =to_pci_dev (hcd->self.controller); + +xhci_shutdown (hcd); +pci_set_power_state (pdev, PCI_D3hot);
Not sure we should force D3 here.
I think usb core will set the PCI D state in the next .poweroff_noirq stage,
for s4:
.poweroff = hcd_pci_suspend,
.poweroff_late = hcd_pci_poweroff_late,
.poweroff_noirq = hcd_pci_suspend_noirq,
hcd_pci_suspend_noirq()
pci_prepare_to_sleep();
target_state = pci_target_state(dev, wakeup)
pci_set_power_state(dev, target_state)
Maybe the target_state isn't D3 for some reason? (missing ACPI entries?)
Thanks
Mathias
Re: [PATCH 1/2] xhci: pci: If no ports have wakeup enabled then disable PCI device at S4
Quoted 48 lines · Mathias Nyman
Quoted 28 lines · On 12.7.2024 21.54, [email protected] wrote:
From: Mario Limonciello <[email protected]>
If a port on an XHCI controller hasn't been marked for wakeup at S4, then leaving it at D0 will needlessly consume power than necessary.
Explicitly check ports configured for wakeup and if none are found then put the controller into D3hot before hibernate.
Signed-off-by Mario Limonciello <[email protected]>---
drivers/usb/host/xhci-pci.c| 9 +++++++++1 file changed, 9 insertions(+)drivers/usb/host/xhci-pci.c +1
-0@@ -823,6 +823,7 @@ static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup) struct usb_device *udev; u32 portsc; int i; + bool wakeup = false; /** Systems with XHCI_RESET_TO_DEFAULT quirk have boot firmware that @@ -860,6 +861,14 @@ static int xhci_pci_poweroff_late(struct usb_hcd *hcd, bool do_wakeup) port->rhub->hcd->self.busnum, port->hcd_portnum + 1);drivers/usb/host/xhci-pci.c static int xhci_pci_poweroff_late(struct usb_hcd · line 872
Quoted 10 lines
drivers/usb/host/xhci-pci.c +8
-0portsc = xhci_port_state_to_neutral(portsc); writel(portsc | PORT_PE, port->addr); + wakeup = true; + } + + if (!wakeup) { + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); + + xhci_shutdown(hcd); + pci_set_power_state(pdev, PCI_D3hot);Not sure we should force D3 here.
I think usb core will set the PCI D state in the next .poweroff_noirq stage,for s4:
.poweroff =hcd_pci_suspend,
.poweroff_late =hcd_pci_poweroff_late,
.poweroff_noirq =hcd_pci_suspend_noirq,
Quoted 7 lines
hcd_pci_suspend_noirq()
pci_prepare_to_sleep();
target_state=pci_target_state(dev, wakeup)
pci_set_power_state(dev, target_state)Maybe the
target_stateisn't D3 for some reason? (missing ACPI entries?)
Thanks for looking.
Even a lack of ACPI entries *should* still lead to D3hot if wakeup is turned off with that flow.
I'll add some more debugging for the various callbacks and see what I can come up with to explain it.
Can you please also review the other patch in the series?
Thanks!
PATCH 2/2 xhci: pci: Put XHCI controllers into D3hot at shutdown
In reply to [email protected]From: Mario Limonciello <[email protected]>
A workaround was put in place for Haswell systems with spurious events to put XHCI controllers into D3hot at shutdown. This solution actually makes sense for all XHCI controllers though because XHCI controllers left in D0 by the OS may remain in D0 when the SoC goes into S5.
Explicitly put all XHCI controllers into D3hot at shutdown and when module is unloaded.
--- drivers/usb/host/xhci-pci.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)
drivers/usb/host/xhci-pci.c +2 -6
@@ -667,9 +667,7 @@ static void xhci_pci_remove(struct pci_dev *dev) xhci->shared_hcd =NULL ; } -/* Workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (dev, PCI_D3hot); +pci_set_power_state (dev, PCI_D3hot);usb_hcd_pci_remove (dev); }
@@ -882,9 +880,7 @@ static void xhci_pci_shutdown(struct usb_hcd *hcd)xhci_shutdown (hcd);xhci_cleanup_msix (xhci); -/* Yet another workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (pdev, PCI_D3hot); +pci_set_power_state (pdev, PCI_D3hot); }/*-------------------------------------------------------------------------*/
Signature · 1 line
2.43.0
Re: [PATCH 2/2] xhci: pci: Put XHCI controllers into D3hot at shutdown
Quoted 20 lines · On 12.7.2024 21.54, [email protected] wrote:
From: Mario Limonciello <[email protected]>
A workaround was put in place for Haswell systems with spurious events to put XHCI controllers into D3hot at shutdown. This solution actually makes sense for all XHCI controllers though because XHCI controllers left in D0 by the OS may remain in D0 when the SoC goes into S5.
Explicitly put all XHCI controllers into D3hot at shutdown and when module is unloaded.
Signed-off-by Mario Limonciello <[email protected]>--- drivers/usb/host/xhci-pci.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)drivers/usb/host/xhci-pci.c +0
-0
drivers/usb/host/xhci-pci.c static void xhci_pci_remove(struct pci_dev *dev) · line 672
Quoted 9 lines
drivers/usb/host/xhci-pci.c +1
-3@@ -667,9 +667,7 @@ static void xhci_pci_remove(struct pci_dev *dev) xhci->shared_hcd =NULL ; } -/* Workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (dev, PCI_D3hot); +pci_set_power_state (dev, PCI_D3hot);usb_hcd_pci_remove (dev);
Just noticed these have been the wrong way around for a while (impacting HSW).
We should first call usb_hcd_pci_remove() and then pci_set_power_state(D3), otherwise we force a fully running xHC into D3.
Note, with this change we end up first calling pci_disable_device(), then pci_set_power_state(D3)
drivers/usb/host/xhci-pci.c static void xhci_pci_shutdown(struct usb_hcd *hcd) · line 883
Quoted 9 lines
drivers/usb/host/xhci-pci.c +1
-3}@@ -882,9 +880,7 @@ static void xhci_pci_shutdown(struct usb_hcd *hcd)xhci_shutdown (hcd);xhci_cleanup_msix (xhci); -/* Yet another workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (pdev, PCI_D3hot); +pci_set_power_state (pdev, PCI_D3hot);
Looks good
Note that we now end up first calling pci_set_power_state(D3) and then pci_disable_device(). The other way around than the remove case above. I don't know if it matters.
Thanks
Mathias
Re: [PATCH 2/2] xhci: pci: Put XHCI controllers into D3hot at shutdown
In reply to [email protected]Quoted 31 lines · On 24-07-12 13:54:18, [email protected] wrote:
From: Mario Limonciello <[email protected]>
A workaround was put in place for Haswell systems with spurious events to put XHCI controllers into D3hot at shutdown. This solution actually makes sense for all XHCI controllers though because XHCI controllers left in D0 by the OS may remain in D0 when the SoC goes into S5.
Explicitly put all XHCI controllers into D3hot at shutdown and when module is unloaded.
Signed-off-by Mario Limonciello <[email protected]>--- drivers/usb/host/xhci-pci.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)drivers/usb/host/xhci-pci.c +1
-3@@ -667,9 +667,7 @@ static void xhci_pci_remove(struct pci_dev *dev) xhci->shared_hcd =NULL ; } -/* Workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (dev, PCI_D3hot); +pci_set_power_state (dev, PCI_D3hot);usb_hcd_pci_remove (dev); }
drivers/usb/host/xhci-pci.c static void xhci_pci_shutdown(struct usb_hcd *hcd) · line 883
Quoted 7 lines
drivers/usb/host/xhci-pci.c +1
-3@@ -882,9 +880,7 @@ static void xhci_pci_shutdown(struct usb_hcd *hcd)xhci_shutdown (hcd);xhci_cleanup_msix (xhci); -/* Yet another workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (pdev, PCI_D3hot); +pci_set_power_state (pdev, PCI_D3hot);
Hi Mario & Mathias,
According to xHCI spec v1.2: A.1.2 Power State Definitions:
Software shall place each downstream USB port with power enabled into the Suspend or Disabled state before it attempts to move the xHC out of the D0 power state.
But I have not found any USB core code does it, do you have any ideas about it?
We have added the similar codes at non-PCI USB platform, but met above concerns. In fact, we met kernel dump that the thread usb-storage try to access the port status when the platform xHCI code has already put the controller to D3.
Best regards,
Peter
Re: [PATCH 2/2] xhci: pci: Put XHCI controllers into D3hot at shutdown
Quoted 51 lines · Peter Chen
Quoted 31 lines · On 24-07-12 13:54:18, [email protected] wrote:
From: Mario Limonciello <[email protected]>
A workaround was put in place for Haswell systems with spurious events to put XHCI controllers into D3hot at shutdown. This solution actually makes sense for all XHCI controllers though because XHCI controllers left in D0 by the OS may remain in D0 when the SoC goes into S5.
Explicitly put all XHCI controllers into D3hot at shutdown and when module is unloaded.
Signed-off-by Mario Limonciello <[email protected]>--- drivers/usb/host/xhci-pci.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)drivers/usb/host/xhci-pci.c +1
-3@@ -667,9 +667,7 @@ static void xhci_pci_remove(struct pci_dev *dev) xhci->shared_hcd =NULL ; } -/* Workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (dev, PCI_D3hot); +pci_set_power_state (dev, PCI_D3hot);usb_hcd_pci_remove (dev); }drivers/usb/host/xhci-pci.c static void xhci_pci_shutdown(struct usb_hcd *hcd) · line 883
Quoted 7 lines
drivers/usb/host/xhci-pci.c +1
-3@@ -882,9 +880,7 @@ static void xhci_pci_shutdown(struct usb_hcd *hcd)xhci_shutdown (hcd);xhci_cleanup_msix (xhci); -/* Yet another workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (pdev, PCI_D3hot); +pci_set_power_state (pdev, PCI_D3hot);Hi Mario & Mathias,
According to xHCI spec v1.2: A.1.2 Power State Definitions:
Software shall place each downstream USB port with power enabled into the Suspend or Disabled state before it attempts to move the xHC out of the D0 power state.
But I have not found any USB core code does it, do you have any ideas about it?
Quoted 9 lines
We have added the similar codes at non-PCI USB platform, but met above concerns. In fact, we met kernel dump that the thread usb-storage try to access the port status when the platform xHCI code has already put the controller to D3.
Best regards,
Peter
This is pretty tangential to my patch. But FWIW in case you missed we're going to discard this patch in favor of another approach in PCI core.
Regarding your point though If I'm not mistaken this should be handled by the Linux parent/child device model. Each of the ports should be children of the hub they're connected to and the hub a child of the controller. So when doing any actions that start runtime PM on the host controller the children need to first be in runtime PM.
Re: [PATCH 2/2] xhci: pci: Put XHCI controllers into D3hot at shutdown
Quoted 59 lines · Mario Limonciello
Quoted 48 lines · Peter Chen
Quoted 29 lines · On 24-07-12 13:54:18, [email protected] wrote:
From: Mario Limonciello <[email protected]>
A workaround was put in place for Haswell systems with spurious events to put XHCI controllers into D3hot at shutdown. This solution actually makes sense for all XHCI controllers though because XHCI controllers left in D0 by the OS may remain in D0 when the SoC goes into S5.
Explicitly put all XHCI controllers into D3hot at shutdown and when module is unloaded.
Signed-off-by Mario Limonciello <[email protected]>--- drivers/usb/host/xhci-pci.c | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-)drivers/usb/host/xhci-pci.c +1
-3@@ -667,9 +667,7 @@ static void xhci_pci_remove(struct pci_dev *dev) xhci->shared_hcd =NULL ; } -/* Workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (dev, PCI_D3hot); +pci_set_power_state (dev, PCI_D3hot);usb_hcd_pci_remove (dev); }drivers/usb/host/xhci-pci.c static void xhci_pci_shutdown(struct usb_hcd *hcd) · line 882
Quoted 6 lines
drivers/usb/host/xhci-pci.c +1
-3@@ -882,9 +880,7 @@ static void xhci_pci_shutdown(struct usb_hcd *hcd)xhci_shutdown (hcd);xhci_cleanup_msix (xhci); -/* Yet another workaround for spurious wakeups at shutdown with HSW */ -if (xhci->quirks &XHCI_SPURIOUS_WAKEUP ) -pci_set_power_state (pdev, PCI_D3hot); +pci_set_power_state (pdev, PCI_D3hot);Hi Mario & Mathias,
According to xHCI spec v1.2: A.1.2 Power State Definitions:
Software shall place each downstream USB port with power enabled into the Suspend or Disabled state before it attempts to move the xHC out of the D0 power state.
But I have not found any USB core code does it, do you have any ideas about it?
Quoted 9 lines
We have added the similar codes at non-PCI USB platform, but met above concerns. In fact, we met kernel dump that the thread usb-storage try to access the port status when the platform xHCI code has already put the controller to D3.
Best regards,
Peter
Quoted 9 lines
This is pretty tangential to my patch. But FWIW in case you missed we're going to discard this patch in favor of another approach in PCI core.
Regarding your point though If I'm not mistaken this should be handled by the Linux parent/child device model. Each of the ports should be children of the hub they're connected to and the hub a child of the controller. So when doing any actions that start runtime PM on the host controller the children need to first be in runtime PM.
It seems there is no runtime PM suspend for xhci and USB core at .shutdown currently. Alan & Mathias, please correct me if I was wrong.
Thanks,
Peter
Re: [PATCH 2/2] xhci: pci: Put XHCI controllers into D3hot at shutdown
Quoted 31 lines
Quoted 21 lines
Quoted 11 lines
Hi Mario & Mathias,
According to xHCI spec v1.2: A.1.2 Power State Definitions:
Software shall place each downstream USB port with power enabled into the Suspend or Disabled state before it attempts to move the xHC out of the D0 power state.
But I have not found any USB core code does it, do you have any ideas about it?
Quoted 9 lines
We have added the similar codes at non-PCI USB platform, but met above concerns. In fact, we met kernel dump that the thread usb-storage try to access the port status when the platform xHCI code has already put the controller to D3.
Best regards,
PeterQuoted 9 lines
This is pretty tangential to my patch. But FWIW in case you missed we're going to discard this patch in favor of another approach in PCI core.
Regarding your point though If I'm not mistaken this should be handled by the Linux parent/child device model. Each of the ports should be children of the hub they're connected to and the hub a child of the controller. So when doing any actions that start runtime PM on the host controller the children need to first be in runtime PM.
Quoted 3 lines
It seems there is no runtime PM suspend for xhci and USB core at .shutdown currently. Alan & Mathias, please correct me if I was wrong.
I think you are right. At shutdown we only halt the xHC. We don't force ports to suspend or disable state. We only put some selected xHC to D3
USB 2 ports might suspend themselves if there is no activity.
Doesn't seem like usb core hcd code, or hub driver does anything either.
Thanks
Mathias
Re: [PATCH 2/2] xhci: pci: Put XHCI controllers into D3hot at shutdown
Quoted 35 lines · Mathias Nyman
Quoted 31 lines
Quoted 21 lines
Quoted 11 lines
Hi Mario & Mathias,
According to xHCI spec v1.2: A.1.2 Power State Definitions:
Software shall place each downstream USB port with power enabled into the Suspend or Disabled state before it attempts to move the xHC out of the D0 power state.
But I have not found any USB core code does it, do you have any ideas about it?
Quoted 9 lines
We have added the similar codes at non-PCI USB platform, but met above concerns. In fact, we met kernel dump that the thread usb-storage try to access the port status when the platform xHCI code has already put the controller to D3.
Best regards,
PeterQuoted 9 lines
This is pretty tangential to my patch. But FWIW in case you missed we're going to discard this patch in favor of another approach in PCI core.
Regarding your point though If I'm not mistaken this should be handled by the Linux parent/child device model. Each of the ports should be children of the hub they're connected to and the hub a child of the controller. So when doing any actions that start runtime PM on the host controller the children need to first be in runtime PM.
Quoted 3 lines
It seems there is no runtime PM suspend for xhci and USB core at .shutdown currently. Alan & Mathias, please correct me if I was wrong.
Quoted 7 lines
I think you are right. At shutdown we only halt the xHC. We don't force ports to suspend or disable state. We only put some selected xHC to D3
USB 2 ports might suspend themselves if there is no activity.
Doesn't seem like usb core hcd code, or hub driver does anything either.
That's right. Host controller drivers are supposed to handle shutdown operations by themselves. The USB core doesn't do anything.
Alan Stern
Quoted 19 lines · On 7/12/24 13:54, [email protected] wrote:
From: Mario Limonciello <[email protected]>
When the system is put into S4 or S5 XHCI controllers remain in D0. This causes higher power consumption and may compromise energy certifications. Consequently some systems consume more power in S5 than s0i3.
This affects all PCIe devices, but looking at breakdowns XHCI is the biggest offender for power consumption.
This series checks if any wakeups are needed and puts controllers into D3 if no wakeup necessary.
This series is a spiritual successor to [1] which aimed to do this more generally in PCI. It also accomplishes similar goals as [2], but aims for both S4 and S5.
[1] https://lore.kernel.org/linux-pci/[email protected]/#t
[2] https://lore.kernel.org/linux-pci/[email protected]/T/
Quoted 8 lines
Mario Limonciello (2):
xhci: pci: If no ports have wakeup enabled then disable PCI device atS4xhci: pci: Put XHCI controllers into D3hot at shutdown
drivers/usb/host/xhci-pci.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)
Hello,
Any feedback for this series?
Thanks,
Hi Mario,
Quoted 26 lines · Mario Limonciello
Quoted 24 lines · On 7/12/24 13:54, [email protected] wrote:
From: Mario Limonciello <[email protected]>
When the system is put into S4 or S5 XHCI controllers remain in D0. This causes higher power consumption and may compromise energy certifications. Consequently some systems consume more power in S5 than s0i3.
This affects all PCIe devices, but looking at breakdowns XHCI is the biggest offender for power consumption.
This series checks if any wakeups are needed and puts controllers into D3 if no wakeup necessary.
This series is a spiritual successor to [1] which aimed to do this more generally in PCI. It also accomplishes similar goals as [2], but aims for both S4 and S5.
[1] https://lore.kernel.org/linux-pci/[email protected]/#t
[2] https://lore.kernel.org/linux-pci/[email protected]/T/Mario Limonciello (2):
xhci: pci: If no ports have wakeup enabled then disable PCI device atS4xhci: pci: Put XHCI controllers into D3hot at shutdown
Quoted 7 lines
Quoted 3 lines
drivers/usb/host/xhci-pci.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)Hello,
Any feedback for this series?
Does commit 0fab972eef49 ("drivers: core: Detach device from power domain on shutdown") work for your case?
The commit was reverted because it regressed some DT based devices, but probably still worth doing for ACPI based systems.
Kai-Heng
Quoted 2 lines
Thanks,
Quoted 35 lines · Kai-Heng Feng
Hi Mario,
Quoted 32 lines · Mario Limonciello
Quoted 19 lines · On 7/12/24 13:54, [email protected] wrote:
From: Mario Limonciello <[email protected]>
When the system is put into S4 or S5 XHCI controllers remain in D0. This causes higher power consumption and may compromise energy certifications. Consequently some systems consume more power in S5 than s0i3.
This affects all PCIe devices, but looking at breakdowns XHCI is the biggest offender for power consumption.
This series checks if any wakeups are needed and puts controllers into D3 if no wakeup necessary.
This series is a spiritual successor to [1] which aimed to do this more generally in PCI. It also accomplishes similar goals as [2], but aims for both S4 and S5.
[1] https://lore.kernel.org/linux-pci/[email protected]/#t
[2] https://lore.kernel.org/linux-pci/[email protected]/T/Quoted 8 lines
Mario Limonciello (2):
xhci: pci: If no ports have wakeup enabled then disable PCI device at
S4
xhci: pci: Put XHCI controllers into D3hot at shutdowndrivers/usb/host/xhci-pci.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)Hello,
Quoted 11 lines
Quoted 1 line
Any feedback for this series?
Does commit
0fab972eef49("drivers: core: Detach device from power domain on shutdown") work for your case?
The commit was reverted because it regressed some DT based devices, but probably still worth doing for ACPI based systems.Kai-Heng
Quoted 2 lines
Thanks,
Thanks for pointing that out and Mathias thanks for the comments. I've spent some time today looking at the different permutations of patches to see what happens at shutdown to devices.
These are all the patches I tested (in various combinations)
Baseline: 6.11-rc4
FS: 6.11-rc4 + 0fab972eef49
ML: 6.11-rc4 + this series
KH: 6.11-rc4 + https://lore.kernel.org/linux-pci/[email protected]/T/#md69ca96133ae0191eefb2f7f5003ce9cc180ec76
The results are available here (in markdown):
https://gist.github.com/superm1/f8f81e52f5b1d55b64493fdaec38e31c
It seems to me:
* FS didn't change anything
* ML only affects the XHCI controllers (into D3 at S5).
* KH in any combination is the best
Considering this I will scrap this patch series and I will leave a comment your patch KH. Hope we can get that in, it's great.
Thanks!