media: imx.rst: Specify the sabreauto variant
Subsystems (3)
Fabio Estevam
reviewerPATCH v3 1/4 media: imx.rst: Specify the sabreauto variant
Improve the documentation by specifying that the instructions are related to the i.MX6Q sabreauto variant.
This avoids confusion if someone follows these steps on a i.MX6DL sabreauto, which has different numbering on the I2C bus and I2C muxes.
---
Changes since v2:
- None
Documentation/media/v4l-drivers/imx.rst | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
Documentation/media/v4l-drivers/imx.rst +3 -3
@@ -515,10 +515,10 @@ Streaming can then begin independently on the capture device nodes be used to select any supported YUV pixelformat on the capture device nodes, including planar. -SabreAuto with ADV7180 decoder ------------------------------- +i.MX6Q SabreAuto with ADV7180 decoder +------------------------------------- -On the SabreAuto, an on-board ADV7180 SD decoder is connected to the +On the i.MX6Q SabreAuto, an on-board ADV7180 SD decoder is connected to the parallel bus input on the internal video mux to IPU1 CSI0. The following example configures a pipeline to capture from the ADV7180
Signature · 1 line
2.17.1
Fabio Estevam
reviewerPATCH v3 2/4 media: imx.rst: Provide a real example for the output format
In the i.MX6Q sabreauto pipeline example, it is better to provide a real example for the output format, so do it just like in the previous lines for consistency.
---
Changes since v2:
- None
Documentation/media/v4l-drivers/imx.rst | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
Documentation/media/v4l-drivers/imx.rst +1 -3
@@ -547,8 +547,6 @@ This example configures a pipeline to capture from the ADV7180 video decoder, assuming PAL 720x576 input signals, with Motion Compensated de-interlacing. The adv7180 must output sequential or alternating fields (field type 'seq-tb' for PAL, or 'alternate'). -$outputfmt can be any format supported by the ipu1_ic_prpvf entity -at its output pad: .. code-block:: none
@@ -565,7 +563,7 @@ at its output pad: media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x576]" media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]" media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]" - media-ctl -V "'ipu1_ic_prpvf':1 [fmt:$outputfmt field:none]" + media-ctl -V "'ipu1_ic_prpvf':1 [fmt:AYUV32/720x576 field:none]" Streaming can then begin on the capture device node at "ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any
Signature · 1 line
2.17.1
Fabio Estevam
reviewerPATCH v3 3/4 media: imx.rst: Provide instructions for the i.MX6DL sabreauto
In reply to Fabio EstevamThe i.MX6DL sabreauto has different numbering on the I2C bus and I2C muxes compared to the i.MX6Q as shown in the kernel log below:
[ 5.159423] imx-media: ipu1_csi0_mux:5 -> ipu1_csi0:0 [ 5.164618] imx-media: ipu1_csi1_mux:5 -> ipu1_csi1:0 [ 5.169953] imx-media: adv7180 4-0021:0 -> ipu1_csi0_mux:4
To avoid confusion, add an entry that shows how to setup the links and configure the pads that are specific to the i.MX6DL sabrea
---
Changes since v2:
- Fix I2C and CSI mux numbering (Steve)
- Passed the v4l2-ctl configuration (Steve)
Documentation/media/v4l-drivers/imx.rst | 58 +++++++++++++++++++++++++ 1 file changed, 58 insertions(+)
Documentation/media/v4l-drivers/imx.rst +58 -0
@@ -572,6 +572,64 @@ supported YUV or RGB pixelformat on the capture device node. This platform accepts Composite Video analog inputs to the ADV7180 on Ain1 (connector J42). +i.MX6DL SabreAuto with ADV7180 decoder +-------------------------------------- + +On the i.MX6DL SabreAuto, an on-board ADV7180 SD decoder is connected to the +parallel bus input on the internal video mux to IPU1 CSI0. + +The following example configures a pipeline to capture from the ADV7180 +video decoder, assuming NTSC 720x480 input signals, using simple +interweave (unconverted and without motion compensation). The adv7180 +must output sequential or alternating fields (field type 'seq-bt' for +NTSC, or 'alternate'): + +.. code-block:: none + + # Setup links + media-ctl -l "'adv7180 4-0021':0 -> 'ipu1_csi0_mux':4[1]" + media-ctl -l "'ipu1_csi0_mux':5 -> 'ipu1_csi0':0[1]" + media-ctl -l "'ipu1_csi0':2 -> 'ipu1_csi0 capture':0[1]" + # Configure pads + media-ctl -V "'adv7180 4-0021':0 [fmt:UYVY2X8/720x480 field:seq-bt]" + media-ctl -V "'ipu1_csi0_mux':5 [fmt:UYVY2X8/720x480]" + media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/720x480]" + # Configure "ipu1_csi0 capture" interface (assumed at /dev/video0) + v4l2-ctl -d0 --set-fmt-video=field=interlaced_bt + +Streaming can then begin on /dev/video0. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video0. + +This example configures a pipeline to capture from the ADV7180 +video decoder, assuming PAL 720x576 input signals, with Motion +Compensated de-interlacing. The adv7180 must output sequential or +alternating fields (field type 'seq-tb' for PAL, or 'alternate'). + +.. code-block:: none + + # Setup links + media-ctl -l "'adv7180 4-0021':0 -> 'ipu1_csi0_mux':4[1]" + media-ctl -l "'ipu1_csi0_mux':5 -> 'ipu1_csi0':0[1]" + media-ctl -l "'ipu1_csi0':1 -> 'ipu1_vdic':0[1]" + media-ctl -l "'ipu1_vdic':2 -> 'ipu1_ic_prp':0[1]" + media-ctl -l "'ipu1_ic_prp':2 -> 'ipu1_ic_prpvf':0[1]" + media-ctl -l "'ipu1_ic_prpvf':1 -> 'ipu1_ic_prpvf capture':0[1]" + # Configure pads + media-ctl -V "'adv7180 4-0021':0 [fmt:UYVY2X8/720x576 field:seq-tb]" + media-ctl -V "'ipu1_csi0_mux':5 [fmt:UYVY2X8/720x576]" + media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x576]" + media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]" + media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]" + media-ctl -V "'ipu1_ic_prpvf':1 [fmt:AYUV32/720x576 field:none]" + # Configure "ipu1_ic_prpvf capture" interface (assumed at /dev/video2) + v4l2-ctl -d2 --set-fmt-video=field=none + +Streaming can then begin on /dev/video2. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video2. + +This platform accepts Composite Video analog inputs to the ADV7180 on +Ain1 (connector J42). + SabreSD with MIPI CSI-2 OV5640 ------------------------------
Signature · 1 line
2.17.1
Re: [PATCH v3 3/4] media: imx.rst: Provide instructions for the i.MX6DL sabreauto
Quoted 11 lines · Fabio Estevam
The i.MX6DL sabreauto has different numbering on the I2C bus and I2C muxes compared to the i.MX6Q as shown in the kernel log below:
[ 5.159423] imx-media: ipu1_csi0_mux:5 -> ipu1_csi0:0 [ 5.164618] imx-media: ipu1_csi1_mux:5 -> ipu1_csi1:0 [ 5.169953] imx-media: adv7180 4-0021:0 -> ipu1_csi0_mux:4To avoid confusion, add an entry that shows how to setup the links and configure the pads that are specific to the i.MX6DL sabrea
Signed-off-by Fabio Estevam <[email protected]>
Quoted 77 lines
---
Changes since v2:
- Fix I2C and CSI mux numbering (Steve)
- Passed the v4l2-ctl configuration (Steve)Documentation/media/v4l-drivers/imx.rst | 58 +++++++++++++++++++++++++ 1 file changed, 58 insertions(+)Documentation/media/v4l-drivers/imx.rst +58
-0@@ -572,6 +572,64 @@ supported YUV or RGB pixelformat on the capture device node. This platform accepts Composite Video analog inputs to the ADV7180 on Ain1 (connector J42). +i.MX6DL SabreAuto with ADV7180 decoder +-------------------------------------- + +On the i.MX6DL SabreAuto, an on-board ADV7180 SD decoder is connected to the +parallel bus input on the internal video mux to IPU1 CSI0. + +The following example configures a pipeline to capture from the ADV7180 +video decoder, assuming NTSC 720x480 input signals, using simple +interweave (unconverted and without motion compensation). The adv7180 +must output sequential or alternating fields (field type 'seq-bt' for +NTSC, or 'alternate'): + +.. code-block:: none + + # Setup links + media-ctl -l "'adv7180 4-0021':0 -> 'ipu1_csi0_mux':4[1]" + media-ctl -l "'ipu1_csi0_mux':5 -> 'ipu1_csi0':0[1]" + media-ctl -l "'ipu1_csi0':2 -> 'ipu1_csi0 capture':0[1]" + # Configure pads + media-ctl -V "'adv7180 4-0021':0 [fmt:UYVY2X8/720x480 field:seq-bt]" + media-ctl -V "'ipu1_csi0_mux':5 [fmt:UYVY2X8/720x480]" + media-ctl -V "'ipu1_csi0':2 [fmt:AYUV32/720x480]" + # Configure "ipu1_csi0 capture" interface (assumed at /dev/video0) + v4l2-ctl -d0 --set-fmt-video=field=interlaced_bt + +Streaming can then begin on /dev/video0. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video0. + +This example configures a pipeline to capture from the ADV7180 +video decoder, assuming PAL 720x576 input signals, with Motion +Compensated de-interlacing. The adv7180 must output sequential or +alternating fields (field type 'seq-tb' for PAL, or 'alternate'). + +.. code-block:: none + + # Setup links + media-ctl -l "'adv7180 4-0021':0 -> 'ipu1_csi0_mux':4[1]" + media-ctl -l "'ipu1_csi0_mux':5 -> 'ipu1_csi0':0[1]" + media-ctl -l "'ipu1_csi0':1 -> 'ipu1_vdic':0[1]" + media-ctl -l "'ipu1_vdic':2 -> 'ipu1_ic_prp':0[1]" + media-ctl -l "'ipu1_ic_prp':2 -> 'ipu1_ic_prpvf':0[1]" + media-ctl -l "'ipu1_ic_prpvf':1 -> 'ipu1_ic_prpvf capture':0[1]" + # Configure pads + media-ctl -V "'adv7180 4-0021':0 [fmt:UYVY2X8/720x576 field:seq-tb]" + media-ctl -V "'ipu1_csi0_mux':5 [fmt:UYVY2X8/720x576]" + media-ctl -V "'ipu1_csi0':1 [fmt:AYUV32/720x576]" + media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]" + media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]" + media-ctl -V "'ipu1_ic_prpvf':1 [fmt:AYUV32/720x576 field:none]" + # Configure "ipu1_ic_prpvf capture" interface (assumed at /dev/video2) + v4l2-ctl -d2 --set-fmt-video=field=none + +Streaming can then begin on /dev/video2. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video2. + +This platform accepts Composite Video analog inputs to the ADV7180 on +Ain1 (connector J42). + SabreSD with MIPI CSI-2 OV5640 ------------------------------
Fabio Estevam
reviewerPATCH v3 4/4 media: imx.rst: Pass the v4l2-ctl configuration
In reply to Fabio EstevamPass the v4l2-ctl configuration for the imx6q-sabreauto PAL example for completeness and consistency.
---
Changes since v2:
- Newly introduced patch
Documentation/media/v4l-drivers/imx.rst | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
Documentation/media/v4l-drivers/imx.rst +4 -3
@@ -564,10 +564,11 @@ alternating fields (field type 'seq-tb' for PAL, or 'alternate'). media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]" media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]" media-ctl -V "'ipu1_ic_prpvf':1 [fmt:AYUV32/720x576 field:none]" + # Configure "ipu1_ic_prpvf capture" interface (assumed at /dev/video2) + v4l2-ctl -d2 --set-fmt-video=field=none -Streaming can then begin on the capture device node at -"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any -supported YUV or RGB pixelformat on the capture device node. +Streaming can then begin on /dev/video2. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video2. This platform accepts Composite Video analog inputs to the ADV7180 on Ain1 (connector J42).
Signature · 1 line
2.17.1
Re: [PATCH v3 4/4] media: imx.rst: Pass the v4l2-ctl configuration
Quoted 5 lines · Fabio Estevam
Pass the v4l2-ctl configuration for the imx6q-sabreauto PAL example for completeness and consistency.
Suggested-by Steve Longerbeam <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Quoted 26 lines
---
Changes since v2:
- Newly introduced patchDocumentation/media/v4l-drivers/imx.rst | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)Documentation/media/v4l-drivers/imx.rst +4
-3@@ -564,10 +564,11 @@ alternating fields (field type 'seq-tb' for PAL, or 'alternate'). media-ctl -V "'ipu1_vdic':2 [fmt:AYUV32/720x576 field:none]" media-ctl -V "'ipu1_ic_prp':2 [fmt:AYUV32/720x576 field:none]" media-ctl -V "'ipu1_ic_prpvf':1 [fmt:AYUV32/720x576 field:none]" + # Configure "ipu1_ic_prpvf capture" interface (assumed at /dev/video2) + v4l2-ctl -d2 --set-fmt-video=field=none -Streaming can then begin on the capture device node at -"ipu1_ic_prpvf capture". The v4l2-ctl tool can be used to select any -supported YUV or RGB pixelformat on the capture device node. +Streaming can then begin on /dev/video2. The v4l2-ctl tool can also be +used to select any supported YUV pixelformat on /dev/video2. This platform accepts Composite Video analog inputs to the ADV7180 on Ain1 (connector J42).