Status HPT374 (HighPoint 1540) Sata in 2.6
Hi,
The low end of the market is dominated by the SII3112 chipset, so I'm looking for an alternative 4-port JBOD SATA controller and came across the High Point card.
How is the support of these cards from libata and/or drivers/ide in 2.6?
Alternatively, are there any 4-port (alternatively I can use two 2-port SATA controllers) JBOD SATA PCI cards with good support in the 2.6 kernel (or with patches) in the ~$50 US price range?
Mike
Quoted 1 line · Mike Fedyk
Alternatively, are there any 4-port (alternatively I can use two 2-port SATA controllers) JBOD SATA PCI cards with good support in the 2.6 kernel (or with patches) in the ~$50 US price range?
There is a Promise SATA150 TX4 4-port JBOD card that works fine with libata; I've got a spare if you want it, I replaced it with a 3Ware 8506-8 :-) If you want to make a deal just email me off-list...
Quoted 5 lines · Mike Fedyk
Hi,
The low end of the market is dominated by the SII3112 chipset, so I'm looking for an alternative 4-port JBOD SATA controller and came across the High Point card.
How is the support of these cards from libata and/or
drivers/idein 2.6?
Hmm, it looks like it's "supported by at latest 2.4.21-pre5", but it doesn't give details, or what SATA features are (or not) supported. Though, what Jeff said probably overrides this...
Quoted 1 line · Mike Fedyk
Hmm, it looks like it's "supported by at latest 2.4.21-pre5", but it doesn't give details, or what SATA features are (or not) supported. Though, what Jeff said probably overrides this...
Oh, I remember now...
Jeff said that back in 2003, and that's why I posted in the first place.
Jeff, so if you have any details on the status of support for these cards in the 2.6 kernel (or with patches).
Thanks,
Mike
I think that it may work with drivers/ide/hpt366.c
AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.
Quoted 15 lines · Mike Fedyk
Quoted 3 lines · Mike Fedyk
Hmm, it looks like it's "supported by at latest 2.4.21-pre5", but it doesn't give details, or what SATA features are (or not) supported. Though, what Jeff said probably overrides this...
Oh, I remember now...
Jeff said that back in 2003, and that's why I posted in the first place.
Jeff, so if you have any details on the status of support for these cards in the 2.6 kernel (or with patches).
Thanks,
Mike
Quoted 1 line · Bartlomiej Zolnierkiewicz
I think that it may work with
drivers/ide/hpt366.c
Works for me.
Quoted 2 lines
AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.
That's correct, at least if the chips on the board can be trusted.
Signature · 2 lines
Måns Rullgård [email protected]
Quoted 4 lines · Bartlomiej Zolnierkiewicz
I think that it may work with
drivers/ide/hpt366.cAFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.
Does that limit you to 133MB/s speeds?
And does that mean no hot-swap?
Quoted 6 lines · Mike Fedyk
Quoted 3 lines · Bartlomiej Zolnierkiewicz
I think that it may work with
drivers/ide/hpt366.c
AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.Does that limit you to 133MB/s speeds?
I'd like to a disk achieve even half of that.
Quoted 1 line
And does that mean no hot-swap?
Probably.
Signature · 2 lines
Måns Rullgård [email protected]