Skip to contentSkip to conversation

Status HPT374 (HighPoint 1540) Sata in 2.6

DISCUSSION Mike Fedyk 4 participants 8 messages Mar 16, 2004 – Mar 17, 2004

lore
Share & tools
lore

Mike Fedyk

author
#0 lore raw

Hi,

The low end of the market is dominated by the SII3112 chipset, so I'm looking for an alternative 4-port JBOD SATA controller and came across the High Point card.

How is the support of these cards from libata and/or drivers/ide in 2.6?

Alternatively, are there any 4-port (alternatively I can use two 2-port SATA controllers) JBOD SATA PCI cards with good support in the 2.6 kernel (or with patches) in the ~$50 US price range?

Mike

#1 lore raw
Quoted 1 line · Mike Fedyk

Alternatively, are there any 4-port (alternatively I can use two 2-port SATA controllers) JBOD SATA PCI cards with good support in the 2.6 kernel (or with patches) in the ~$50 US price range?

There is a Promise SATA150 TX4 4-port JBOD card that works fine with libata; I've got a spare if you want it, I replaced it with a 3Ware 8506-8 :-) If you want to make a deal just email me off-list...

author
#2 lore raw
In reply to Mike Fedyk
Quoted 5 lines · Mike Fedyk

Hi,

The low end of the market is dominated by the SII3112 chipset, so I'm looking for an alternative 4-port JBOD SATA controller and came across the High Point card.

How is the support of these cards from libata and/or drivers/ide in 2.6?

Hmm, it looks like it's "supported by at latest 2.4.21-pre5", but it doesn't give details, or what SATA features are (or not) supported. Though, what Jeff said probably overrides this...

http://www.linuxmafia.com/faq/Hardware/sata.html

author
#3 lore raw
Quoted 1 line · Mike Fedyk

Hmm, it looks like it's "supported by at latest 2.4.21-pre5", but it doesn't give details, or what SATA features are (or not) supported. Though, what Jeff said probably overrides this...

Oh, I remember now...

Jeff said that back in 2003, and that's why I posted in the first place.

Jeff, so if you have any details on the status of support for these cards in the 2.6 kernel (or with patches).

Thanks,

Mike

#4 lore raw

I think that it may work with drivers/ide/hpt366.c

AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.

Quoted 15 lines · Mike Fedyk
Quoted 3 lines · Mike Fedyk

Hmm, it looks like it's "supported by at latest 2.4.21-pre5", but it doesn't give details, or what SATA features are (or not) supported. Though, what Jeff said probably overrides this...

Oh, I remember now...

Jeff said that back in 2003, and that's why I posted in the first place.

Jeff, so if you have any details on the status of support for these cards in the 2.6 kernel (or with patches).

Thanks,

Mike

#5 lore raw
Quoted 1 line · Bartlomiej Zolnierkiewicz

I think that it may work with drivers/ide/hpt366.c

Works for me.

Quoted 2 lines

AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.

That's correct, at least if the chips on the board can be trusted.

Signature · 2 lines
Måns Rullgård
[email protected]
author
#6 lore raw
In reply to Bartlomiej Zolnierkiewicz
Quoted 4 lines · Bartlomiej Zolnierkiewicz

I think that it may work with drivers/ide/hpt366.c

AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.

Does that limit you to 133MB/s speeds?

And does that mean no hot-swap?

#7 lore raw
Quoted 6 lines · Mike Fedyk
Quoted 3 lines · Bartlomiej Zolnierkiewicz

I think that it may work with drivers/ide/hpt366.c
AFAIK HPT374 is PATA only chipset and SATA support in HighPoint 1540 is achieved by using PATA-SATA bridges.

Does that limit you to 133MB/s speeds?

I'd like to a disk achieve even half of that.

Quoted 1 line

And does that mean no hot-swap?

Probably.

Signature · 2 lines
Måns Rullgård
[email protected]