VFS does not find /dev/sda3 (8,3), Kernel Panic
Hi
I have been trying this for some days now:
I'm trying to boot onto my first Serial ATA Disk (SATA1). My config, lspci and lsmod are attached.
When I boot from the Gentoo-Minimal-Install-CD everything works great and the disks are correctly recognised as /dev/sda and /dev/sdb.
I took the /proc/config.gz from the chrooted and mounted system and compiled a new kernel off it. I made sure that all the SATA drivers are (*) and not (M). Then I tried to boot into the new kernel and BAM:
Kernel Panic, VFS can not find root (sda3) (8,3).
My motherboard is an Intel SE7520BD2 and my HD is a Maxtor SATA 200GB.
Any clou's or insights are greatly appreciated!
Thanks
Zeno
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Yes, sorry, your are right. To much configuring in my brain.
Check the new config. I suppose I only need the Intel PII/ICH SATA support (as my lspci tells me).
But I get the same result; a Kernel Panic VFS not found (8,3)... but my HDD is on /dev/sda3.
Is there any why I can get more detailed info out of my kernel-boot (except from my screen)?
Any other hints?
Thanks for your help.
Zeno
Quoted 26 lines · Dirk Heinrichs
Am Freitag, 13. Mai 2005 10:23 schrieb ext Zeno Davatz:
Quoted 4 lines
I took the
/proc/config.gzfrom the chrooted and mounted system and compiled a new kernel off it. I made sure that all the SATA drivers are (*) and not (M).No, you didn't. All (!?) hardware drivers are M, they (or better, the one for your controller) should be *.
When configuring your kernel look into "SCSI low-level drivers" and enable the driver for your controller.
HTH...
Dirk
--Dirk Heinrichs | Tel: +49 (0)162 234 3408 Configuration Manager | Fax: +49 (0)211 47068 111 Capgemini Deutschland | Mail: [email protected]Hambornerstraße 55 | Web: http://www.capgemini.com
D-40472 Düsseldorf | ICQ#: 110037733
GPG Public Key C2E467BB | Keyserver: www.keyserver.net
A message that is not in the archive (sent off-list or not yet received): [email protected]
Ok, thanks for all your help, I found out: it was a faulty (new !! SATA disk).
Thanks again
Zeno
Quoted 33 lines · Dirk Heinrichs
Am Freitag, 13. Mai 2005 12:03 schrieb ext Zeno Davatz:
Quoted 10 lines
Yes, sorry, your are right. To much configuring in my brain.
Check the new config. I suppose I only need the Intel PII/ICH SATA support (as my lspci tells me).
But I get the same result; a Kernel Panic VFS not found (8,3)... but my HDD is on
/dev/sda3.Is there any why I can get more detailed info out of my kernel-boot (except from my screen)?
In "make menuconfig", the help text for this driver says:
"This option enables support for ICH5 Serial ATA. If PATA support was enabled previously, this enables support for select Intel PIIX/ICH PATA host controllers."
Maybe you should switch off PATA first.
HTH...
Dirk
--Dirk Heinrichs | Tel: +49 (0)162 234 3408 Configuration Manager | Fax: +49 (0)211 47068 111 Capgemini Deutschland | Mail: [email protected]Hambornerstraße 55 | Web: http://www.capgemini.com
D-40472 Düsseldorf | ICQ#: 110037733
GPG Public Key C2E467BB | Keyserver: www.keyserver.net