Skip to contentSkip to conversation

VFS does not find /dev/sda3 (8,3), Kernel Panic

DISCUSSION Zeno Davatz 1 participant 3 messages May 13, 2005 3 messages not in the archive

lore
Share & tools
lore
#0 lore raw

Hi

I have been trying this for some days now:

I'm trying to boot onto my first Serial ATA Disk (SATA1). My config, lspci and lsmod are attached.
When I boot from the Gentoo-Minimal-Install-CD everything works great and the disks are correctly recognised as /dev/sda and /dev/sdb.

I took the /proc/config.gz from the chrooted and mounted system and compiled a new kernel off it. I made sure that all the SATA drivers are (*) and not (M). Then I tried to boot into the new kernel and BAM:
Kernel Panic, VFS can not find root (sda3) (8,3).

My motherboard is an Intel SE7520BD2 and my HD is a Maxtor SATA 200GB.

Any clou's or insights are greatly appreciated!

Thanks
Zeno

#3 lore raw
In reply to a message not in the archive

Yes, sorry, your are right. To much configuring in my brain.

Check the new config. I suppose I only need the Intel PII/ICH SATA support (as my lspci tells me).

But I get the same result; a Kernel Panic VFS not found (8,3)... but my HDD is on /dev/sda3.

Is there any why I can get more detailed info out of my kernel-boot (except from my screen)?

Any other hints?

Thanks for your help.
Zeno

Quoted 26 lines · Dirk Heinrichs

Am Freitag, 13. Mai 2005 10:23 schrieb ext Zeno Davatz:

Quoted 4 lines

I took the /proc/config.gz from the chrooted and mounted system and compiled a new kernel off it. I made sure that all the SATA drivers are (*) and not (M).

No, you didn't. All (!?) hardware drivers are M, they (or better, the one for your controller) should be *.

When configuring your kernel look into "SCSI low-level drivers" and enable the driver for your controller.

HTH...

Dirk
--

Dirk Heinrichs          | Tel:  +49 (0)162 234 3408
Configuration Manager   | Fax:  +49 (0)211 47068 111
Capgemini Deutschland   | Mail: [email protected]

Hambornerstraße 55 | Web: http://www.capgemini.com
D-40472 Düsseldorf | ICQ#: 110037733
GPG Public Key C2E467BB | Keyserver: www.keyserver.net

#5 lore raw
In reply to a message not in the archive

Ok, thanks for all your help, I found out: it was a faulty (new !! SATA disk).

Thanks again
Zeno

Quoted 33 lines · Dirk Heinrichs

Am Freitag, 13. Mai 2005 12:03 schrieb ext Zeno Davatz:

Quoted 10 lines

Yes, sorry, your are right. To much configuring in my brain.

Check the new config. I suppose I only need the Intel PII/ICH SATA support (as my lspci tells me).

But I get the same result; a Kernel Panic VFS not found (8,3)... but my HDD is on /dev/sda3.

Is there any why I can get more detailed info out of my kernel-boot (except from my screen)?

In "make menuconfig", the help text for this driver says:

"This option enables support for ICH5 Serial ATA. If PATA support was enabled previously, this enables support for select Intel PIIX/ICH PATA host controllers."

Maybe you should switch off PATA first.

HTH...

Dirk
--

Dirk Heinrichs          | Tel:  +49 (0)162 234 3408
Configuration Manager   | Fax:  +49 (0)211 47068 111
Capgemini Deutschland   | Mail: [email protected]

Hambornerstraße 55 | Web: http://www.capgemini.com
D-40472 Düsseldorf | ICQ#: 110037733
GPG Public Key C2E467BB | Keyserver: www.keyserver.net