Skip to contentSkip to conversation

Loadbalancing how to ? ? ? ?

LARTC Cao Van Khanh 4 participants 4 messages Jul 2, 2005 – Jul 3, 2005

lore
Share & tools
lore
#0 lore raw

I have 2 ADSL ad1 and ad2 , one PC for my firewall and some deamon on it with 3 ethernet : eth0 connect to my LAN ( 192.168.60.0/24 ) and 2 other connect to ad1 and ad2

|eth1 (10.0.1.2)--------------------ad1 ( ADSL 1 )

|

My LAN(192.168.60.0/24) |---------eth0( 192.168.60.2)--> PC

|

|eth2 (10.0.2.2)---------------------ad2 (ADSL 2 )

All computer in LAN has default router = 191.168.60.2 ( eth0 of PC )

In the /etc/network/option I enable the forwardable = 1

I use iptable to NAT the outgoing of eth1 and eth2

Iptables -t nat -A POSTROUTING -s 192.168.60.0/24 -o eth1 -j SNAT -to 10.0.1.2

Iptables -t nat -A POSTROUTING -s 192.168.60.0/24 -o eth2 -j SNAT -to 10.0.2.2

Ofcause by default the eth1 will always be forwarded from LAN and nerver the ADSL 2 was use

The ideal of mine is writing a programe loadbalancing for n line ADSL contact to one PC as gateway ,But when the packet reach the eth0 , how to control it forwarld to eth1 or eth2 is my problem .

If I could do that , maybe I could find the way to loadbalacing n line ADSL as one biger . If someone know how to or have some idea , give me some information :-)

Thank for reading

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw
Quoted 5 lines

Iptables -t nat -A POSTROUTING -s 192.168.60.0/24 -j SNAT -to 10.0.1.2,10.0.2.2

this does some primitive lb i think :
man iptables says :

You can add several --to-source options. If you specify more
than one source address, either via an address range or multiple --to-source options, a simple round-robin (one after another in cycle) takes place between these adresses.

Signature · 5 lines
*Dariusz 'tdi' Dwornikowski | Gentoo | admin at pozman.pl     |
*[JID]:[email protected]|[gg]:2266034|[IRC]:#gentoo-pl@freenode   |
*[MAIL]:[email protected]|[WWW]:www.tdi.pozman.pl                 | 
*Serwery,administracja,webapps - www.ProAdmin.com.pl          |
*Fingerprint:43E21CC46DAFD2F754E91547D59B39F56AAA4B5F         |

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#2 lore raw
In reply to Cao Van Khanh

Witaj Cao,

W Twoim liœcie datowanym 2 lipca 2005 (17:40:05) mo¿na przeczytaæ:

CVK> I have 2 ADSL ad1 and ad2 , one PC for my firewall and some CVK> deamon on it with 3 ethernet : eth0 connect to my LAN (

This question comes and goes on this list :)

Please read information at: http://www.ssi.bg/~ja/ , especially http://www.ssi.bg/~ja/nano.txt
and you can try my script http://www.ssi.bg/~ja/tmp/mpath2.sh to
load balance 2 (or more - I was using 4) connections with great
success. No daemon needed :)

There are also other solutions in list archive.

IMHO the routing code has precedence over iptables so it chooses the outgoing interface over which the iptables will SNAT in input routing process. And thats why you will not see the effect in this setup (thi interface has already been chosen). It is possible (and reasonable) to SNAT to multiple IPs residing on one interface.

Correct me if I'm wrong, please...:)

Signature · 7 lines
Greetings,
 Robert Kurjata

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#3 lore raw
In reply to Cao Van Khanh

Is it possible to combine the 2 or 4 ADSL line into 1 line (big pipe)?

Regards,
ro0ot

Quoted 16 lines · Robert Kurjata

Witaj Cao,

W Twoim liœcie datowanym 2 lipca 2005 (17:40:05) mo¿na przeczytaæ:

CVK> I have 2 ADSL ad1 and ad2 , one PC for my firewall and some CVK> deamon on it with 3 ethernet : eth0 connect to my LAN (

This question comes and goes on this list :)

Please read information at: http://www.ssi.bg/~ja/ , especially http://www.ssi.bg/~ja/nano.txt
and you can try my script http://www.ssi.bg/~ja/tmp/mpath2.sh to
load balance 2 (or more - I was using 4) connections with great
success. No daemon needed :)

There are also other solutions in list archive.

Quoted 10 lines

IMHO the routing code has precedence over iptables so it chooses the outgoing interface over which the iptables will SNAT in input routing process. And thats why you will not see the effect in this setup (thi interface has already been chosen). It is possible (and reasonable) to SNAT to multiple IPs residing on one interface.

Correct me if I'm wrong, please...:)

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc