Skip to contentSkip to conversation

Using aplay and arecord on an ARM

DISCUSSION Paul Kavan 5 participants 22 messages Jun 19, 2007 – Jun 20, 2007 3 messages not in the archive

lore
Share & tools
lore

Paul Kavan

author
#0 lore raw

Liam:

I have managed to get the alsa-libs and aplay, arecord, and speaker-test on my board, but I am unsure how to get them to play. I have tried making the device nodes and am using a simple alsa.conf, but still no joy. I am sure there is something simple I am missing.

Trying to find some documentation on this. I am assuming there is some disconnect between the interface and my conf file. I have my alsa.conf file in /usr/share/alsa/ and it is:

pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}

ctl.w6811 {
type hw
card 0
}
pcm.w6811 {
type hw
card 0
device 0
subdevice 0
}

ctl.!default = ctl.w6811
pcm.!default = pcm.w6811

ctl.hw {
       @args[ CARD ]
       @args.CARD {
               type string
               default "0"
       }
       type hw
       card $CARD
}
pcm.hw {
       @args[ CARD DEV SUBDEV ]
       @args.CARD {
               type string
               default "0"
       }
       @args.DEV {
               type integer
               default 0
       }
       @args.SUBDEV {
               type integer
               default 0
       }
       type hw
       card $CARD
       device $DEV
       subdevice $SUBDEV
}

I have some /proc/ entries:

/proc/asound $ ls

GRHEKW6811  cards       pcm         version
card0       devices     timers

/proc/asound $ cat cards
0 [GRHEKW6811 ]: W6811 - GRH_EK_W6811

                      GRH_EK_W6811 (W6811)

/proc/asound $ cat devices
0: [ 0] : control
16: [ 0- 0]: digital audio playback
24: [ 0- 0]: digital audio capture
33: : timer

/proc/asound $ cat pcm
00-00: W6811 W6811-PCM-0 : : playback 1 : capture 1

/proc/asound $ cat timers
G0: system timer : 10000.000us (10000000 ticks)
P0-0-0: PCM playback 0-0-0 : SLAVE
P0-0-1: PCM capture 0-0-1 : SLAVE

/proc/asound $ cat version
Advanced Linux Sound Architecture Driver Version 1.0.14rc4 (Wed May 09 09:51:39.

Now, into GRHEKW6811 (which takes me to card0) I get a pcm0c and pcm0p directory. Using cat info, I get:

/proc/asound/card0/pcm0c $ cat info
card: 0
device: 0
subdevice: 0
stream: CAPTURE
id: W6811 W6811-PCM-0
name:
subname: subdevice #0
class: 0
subclass: 0
subdevices_count: 1
subdevices_avail: 1

/proc/asound/card0/pcm0c $ cd ../pcm0p/
/proc/asound/card0/pcm0p $ cat info
card: 0
device: 0
subdevice: 0
stream:
PLAYBACK
id: W6811
W6811-PCM-0
name:

subname: subdevice
#0
class:
0
subclass:
0
subdevices_count:
1
subdevices_avail: 1

I then did:

mknod -m 666 /dev/snd/pcm0p c 116 0
mknod -m 666 /dev/snd/pcm0c c 116 0

However, when I try speaker-test, I get:

/usr/lib/bin $ ./speaker-test -D pcm0p

speaker-test 1.0.14

Playback device is pcm0p
Stream parameters are 48000Hz, S16_LE, 1 channels Using 16 octaves of pink noise
ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM pcm0p Playback open error: -2,No such file or directory

Same for default:

/usr/lib/bin $ ./speaker-test -D
default

speaker-test 1.0.14

Playback device is
default
Stream parameters are 48000Hz, S16_LE, 1 channels
Using 16 octaves of pink
noise
ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM default
Playback open error: -2,No such file or directory

When I try aplay -l and arecord -l, I get:

/usr/lib/bin $ ./aplay
-l
aplay: device_list:204: no soundcards
found...
/usr/lib/bin $ ./arecord
-l
arecord: device_list:204: no soundcards found...

I am at a loss here. Anyone have any advice, pointers, tips, etc......

Thanks.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
#1 lore raw
Quoted 4 lines · Paul Kavan

I have managed to get the alsa-libs and aplay, arecord, and speaker-test on my board, but I am unsure how to get them to play. I have tried making the device nodes and am using a simple alsa.conf, but still no joy. I am sure there is something simple I am missing.

What does "strace aplay file.wav" output?

Lee

author
#2 lore raw
Quoted 5 lines · Lee Revell
Quoted 1 line · Paul Kavan

I have managed to get the alsa-libs and aplay, arecord, and speaker-test

on

Quoted 1 line

my board, but I am unsure how to get them to play. I have tried making

Quoted 9 lines

the

Quoted 1 line

device nodes and am using a simple alsa.conf, but still no joy. I am

sure

Quoted 1 line

there is something simple I am missing.

What does "strace aplay file.wav" output?

Lee

Here is the output of strace aplay Noise.wav:

/usr/lib/share/sounds/alsa $ strace aplay Noise.wav execve("/usr/sbin/aplay", ["aplay", "Noise.wav"], [/* 7 vars */]) = 0 mmap2(NULL, 20, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40005000
stat("/etc/ld.so.cache", {st_mode=S_IFREG|0644, st_size=1150, ...}) = 0
open("/etc/ld.so.cache", O_RDONLY) = 3
mmap2(NULL, 1150, PROT_READ, MAP_SHARED, 3, 0) = 0x40006000
close(3) = 0
open("/usr/lib/libasound.so.2", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0755, st_size=770500, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0\24\373\1"..., 4096) = 4096
mmap2(NULL, 770048, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x4000e000
mmap2(0x4000e000, 752456, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x4000e000
mmap2(0x400c6000, 15744, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xb8) = 0x400c6000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libm.so.0", O_RDONLY)        = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0t\22\0\000"..., 4096) = 4096
mmap2(NULL, 81920, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400ca000 mmap2(0x400ca000, 41428, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400ca000
mmap2(0x400dc000, 4100, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400dc000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libdl.so.0", O_RDONLY)       = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0(\10\0\000"..., 4096) = 4096
mmap2(NULL, 40960, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400de000 mmap2(0x400de000, 5760, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400de000
mmap2(0x400e7000, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x1) = 0x400e7000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libpthread.so.0", O_RDONLY)  = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0D<\0\0004"..., 4096) = 4096
mmap2(NULL, 106496, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400e8000
mmap2(0x400e8000, 40952, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400e8000
mmap2(0x400fa000, 21732, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400fa000
mmap2(0x40100000, 5788, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x401000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libgcc_s.so.1", O_RDONLY)    = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0X\25\0\000"..., 4096) = 4096
mmap2(NULL, 65536, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40102000 mmap2(0x40102000, 28800, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40102000
mmap2(0x40111000, 548, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x7) = 0x40111000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libc.so.0", O_RDONLY)        = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0000\253\0"..., 4096) = 4096
mmap2(NULL, 360448, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40112000
mmap2(0x40112000, 302380, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40112000
mmap2(0x40164000, 5172, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x4a) = 0x40164000
mmap2(0x40166000, 16020, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x40160

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libm.so.0", O_RDONLY)        = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0
close(3) = 0
open("/lib/libdl.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0
close(3) = 0
open("/lib/libpthread.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0
close(3) = 0
open("/lib/libgcc_s.so.1", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
munmap(0x40006000, 1150) = 0
stat("/lib/ld-uClibc.so.0", {st_mode=S_IFREG|0755, st_size=21096, ...}) = 0

mprotect(0x400dc000, 4096, PROT_READ)   = 0
mprotect(0x400e7000, 4096, PROT_READ)   = 0
mprotect(0x400fa000, 4096, PROT_READ)   = 0
mprotect(0x40164000, 4096, PROT_READ)   = 0
mprotect(0x4000c000, 4096, PROT_READ)   = 0

ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0
ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0
getpid() = 764
getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0 setrlimit(RLIMIT_STACK, {rlim_cur=2040*1024, rlim_max=RLIM_INFINITY}) = 0 rt_sigaction(SIGRTMIN, {0x400f1d70, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0
rt_sigaction(SIGRT_1, {0x400f1c98, [RTMIN], 0x4000000 /* SA_??? */}, NULL,
8) = 0
rt_sigaction(SIGRT_2, {0x400f12d0, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0 rt_sigprocmask(SIG_BLOCK, [RTMIN], NULL, 8) = 0 rt_sigprocmask(SIG_UNBLOCK, [RT_1], NULL, 8) = 0
brk(0) = 0x1c000
brk(0x1d000) = 0x1d000
stat("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", 0xbebe4b70) = -1 ENOENT (No)
write(2, "ALSA lib ", 9ALSA lib ) = 9
write(2, "pcm.c", 5pcm.c) = 5
write(2, ":", 1:) = 1
write(2, "2144", 42144) = 4
write(2, ":(", 2:() = 2
write(2, "snd_pcm_open_noupdate", 21snd_pcm_open_noupdate) = 21
write(2, ") ", 2) ) = 2
write(2, "Unknown PCM ", 12Unknown PCM ) = 12
write(2, "default", 7default) = 7
write(2, "\n", 1
) = 1
write(2, "aplay", 5aplay) = 5
write(2, ": ", 2: ) = 2
write(2, "main", 4main) = 4
write(2, ":", 1:) = 1
write(2, "545", 3545) = 3
write(2, ": ", 2: ) = 2
write(2, "audio open error: ", 18audio open error: ) = 18
write(2, "No such file or directory", 25No such file or directory) = 25 write(2, "\n", 1
) = 1
exit(1) = ?
Process 764 detached

Something here sticks out as a problem. There is a line:

stat("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", 0xbebe4b70) = -1

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf

How do I change that?

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
#3 lore raw
Quoted 2 lines · Paul Kavan

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf

I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.

Lee

author
#4 lore raw
Quoted 10 lines · Lee Revell
Quoted 2 lines · Paul Kavan

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf

I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.

Lee

Thanks Lee, I will try to hunt that down. The list archives on
http://mailman.alsa-project.org/pipermail/alsa-devel/ only go back to March....might be a fun search.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
author
#5 lore raw

Found a quick workaround....although I would like to clean it up. Still does not work, but gets past the not finding the alsa.conf part.

strace aplay Noise.wav now gives:

/usr/lib/share/sounds/alsa $ strace aplay Noise.wav execve("/usr/sbin/aplay", ["aplay", "Noise.wav"], [/* 7 vars */]) = 0 mmap2(NULL, 20, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40005000
stat("/etc/ld.so.cache", {st_mode=S_IFREG|0644, st_size=1150, ...}) = 0
open("/etc/ld.so.cache", O_RDONLY) = 3
mmap2(NULL, 1150, PROT_READ, MAP_SHARED, 3, 0) = 0x40006000
close(3) = 0
open("/usr/lib/libasound.so.2", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0755, st_size=770500, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0\24\373\1"..., 4096) = 4096
mmap2(NULL, 770048, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x4000e000
mmap2(0x4000e000, 752456, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x4000e000
mmap2(0x400c6000, 15744, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xb8) = 0x400c6000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libm.so.0", O_RDONLY)        = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0t\22\0\000"..., 4096) = 4096
mmap2(NULL, 81920, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400ca000 mmap2(0x400ca000, 41428, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400ca000
mmap2(0x400dc000, 4100, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400dc000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libdl.so.0", O_RDONLY)       = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0(\10\0\000"..., 4096) = 4096
mmap2(NULL, 40960, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400de000 mmap2(0x400de000, 5760, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400de000
mmap2(0x400e7000, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x1) = 0x400e7000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libpthread.so.0", O_RDONLY)  = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0D<\0\0004"..., 4096) = 4096
mmap2(NULL, 106496, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400e8000
mmap2(0x400e8000, 40952, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400e8000
mmap2(0x400fa000, 21732, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400fa000
mmap2(0x40100000, 5788, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x401000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libgcc_s.so.1", O_RDONLY)    = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0X\25\0\000"..., 4096) = 4096
mmap2(NULL, 65536, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40102000 mmap2(0x40102000, 28800, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40102000
mmap2(0x40111000, 548, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x7) = 0x40111000

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libc.so.0", O_RDONLY)        = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0000\253\0"..., 4096) = 4096
mmap2(NULL, 360448, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40112000
mmap2(0x40112000, 302380, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40112000
mmap2(0x40164000, 5172, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x4a) = 0x40164000
mmap2(0x40166000, 16020, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x40160

close(3)                                = 0
munmap(0x40007000, 4096)                = 0
open("/lib/libm.so.0", O_RDONLY)        = 3

fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0
close(3) = 0
open("/lib/libdl.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0
close(3) = 0
open("/lib/libpthread.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0
close(3) = 0
open("/lib/libgcc_s.so.1", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
open("/lib/libc.so.0", O_RDONLY) = 3
fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0
munmap(0x40006000, 1150) = 0
stat("/lib/ld-uClibc.so.0", {st_mode=S_IFREG|0755, st_size=21096, ...}) = 0

mprotect(0x400dc000, 4096, PROT_READ)   = 0
mprotect(0x400e7000, 4096, PROT_READ)   = 0
mprotect(0x400fa000, 4096, PROT_READ)   = 0
mprotect(0x40164000, 4096, PROT_READ)   = 0
mprotect(0x4000c000, 4096, PROT_READ)   = 0

ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0
ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0
getpid() = 844
getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0 setrlimit(RLIMIT_STACK, {rlim_cur=2040*1024, rlim_max=RLIM_INFINITY}) = 0 rt_sigaction(SIGRTMIN, {0x400f1d70, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0
rt_sigaction(SIGRT_1, {0x400f1c98, [RTMIN], 0x4000000 /* SA_??? */}, NULL,
8) = 0
rt_sigaction(SIGRT_2, {0x400f12d0, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0 rt_sigprocmask(SIG_BLOCK, [RTMIN], NULL, 8) = 0 rt_sigprocmask(SIG_UNBLOCK, [RT_1], NULL, 8) = 0
brk(0) = 0x1c000
brk(0x1d000) = 0x1d000
stat("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", {st_mode=S_IFREG|0644, st_s0 open("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", O_RDONLY) = 3
ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xbed04b14) = -1 ENOTTY (Inappropriate ioctl for device)
brk(0x1e000) = 0x1e000
read(3, "pcm.!default {\n type hw\n car"..., 4096) = 864
write(2, "ALSA lib ", 9ALSA lib ) = 9
write(2, "conf.c", 6conf.c) = 6
write(2, ":", 1:) = 1
write(2, "975", 3975) = 3
write(2, ":(", 2:() = 2
write(2, "parse_value", 11parse_value) = 11
write(2, ") ", 2) ) = 2
write(2, "card", 4card) = 4
write(2, " is not a string", 16 is not a string) = 16
write(2, "\n", 1
) = 1
write(2, "ALSA lib ", 9ALSA lib ) = 9
write(2, "conf.c", 6conf.c) = 6
write(2, ":", 1:) = 1
write(2, "1588", 41588) = 4
write(2, ":(", 2:() = 2
write(2, "snd_config_load1", 16snd_config_load1) = 16
write(2, ") ", 2) ) = 2
write(2, "_toplevel_", 10_toplevel_) = 10
write(2, ":", 1:) = 1
write(2, "45", 245) = 2

write(2, ":", 1:)                        = 1
write(2, "1", 11)                        = 1
write(2, ":", 1:)                        = 1

write(2, "Invalid argument", 16Invalid argument) = 16
write(2, "\n", 1
) = 1
close(3) = 0
write(2, "ALSA lib ", 9ALSA lib ) = 9
write(2, "conf.c", 6conf.c) = 6
write(2, ":", 1:) = 1
write(2, "3066", 43066) = 4
write(2, ":(", 2:() = 2
write(2, "snd_config_update_r", 19snd_config_update_r) = 19
write(2, ") ", 2) ) = 2
write(2, "/home/grhuser/buildroot/build_ar"..., 63/home/grhuser/buildroot/build_arm/root/usr/share/3
write(2, " may be old or corrupted: consid"..., 54 may be old or corrupted:
consider to remove or f4
write(2, "\n", 1
) = 1
write(2, "aplay", 5aplay) = 5
write(2, ": ", 2: ) = 2
write(2, "main", 4main) = 4
write(2, ":", 1:) = 1
write(2, "545", 3545) = 3
write(2, ": ", 2: ) = 2
write(2, "audio open error: ", 18audio open error: ) = 18
write(2, "Invalid argument", 16Invalid argument) = 16
write(2, "\n", 1
) = 1
exit(1) = ?
Process 844 detached

Not sure if this helps, but trying to make some progress.

Paul

#6 lore raw
In reply to Lee Revell

At Tue, 19 Jun 2007 16:31:31 -0400,

Quoted 7 lines · Lee Revell
Quoted 2 lines · Paul Kavan

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf

I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.

The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.

Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.

Takashi

#7 lore raw

Build alsa-lib and alsa-utils with prefix option

--prefix=/usr

while installing give the destination directory

make install DESTDIR=$MYINSTALLDIR

Then copy the installed executables to ARM root file sytem

This should solve the issue.

Quoted 24 lines · Takashi Iwai

At Tue, 19 Jun 2007 16:31:31 -0400,

Quoted 7 lines · Lee Revell
Quoted 2 lines · Paul Kavan

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf

I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.

The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.

Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.

Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#8 lore raw
Quoted 13 lines · Nobin Mathew

Build alsa-lib and alsa-utils with prefix option

--prefix=/usr

while installing give the destination directory

make install DESTDIR=$MYINSTALLDIR

Then copy the installed executables to ARM root file sytem

This should solve the issue.

Quoted 21 lines
Quoted 6 lines · Takashi Iwai

At Tue, 19 Jun 2007 16:31:31 -0400,

Quoted 4 lines · Lee Revell
Quoted 2 lines · Paul Kavan

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the

alsa.conf

Quoted 13 lines
Quoted 3 lines

I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.

The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.

Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.

Takashi

Thanks Takashi and Mathew. I just want to make sure I am clear on this. I create my embedded rfs for an ARM9 processor on my host machine. The path to the rfs is:

$HOME/buildroot/build_arm/root/...

So, you are saying that when I configure alsa-libs, I should be using:

CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no
--prefix=/usr

and then

make install DESTDIR=$HOME/buildroot/build_arm/root

Is this correct? I just want to make sure the libs will get into my target's rfs that way.

Thanks.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
#9 lore raw

Yes, but take care of permissions. you need root permissions in ARM root file system.

Quoted 69 lines · Paul Kavan
Quoted 6 lines · Nobin Mathew

Build alsa-lib and alsa-utils with prefix option

--prefix=/usr

while installing give the destination directory

Quoted 13 lines

make install DESTDIR=$MYINSTALLDIR

Then copy the installed executables to ARM root file sytem

This should solve the issue.

Quoted 6 lines · Takashi Iwai

At Tue, 19 Jun 2007 16:31:31 -0400,

Quoted 4 lines · Lee Revell
Quoted 2 lines · Paul Kavan

it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the

alsa.conf

Quoted 7 lines
Quoted 7 lines
Quoted 3 lines

I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.

The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.

Quoted 6 lines
Quoted 6 lines

Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.

Takashi

Thanks Takashi and Mathew. I just want to make sure I am clear on this. I create my embedded rfs for an ARM9 processor on my host machine. The path to the rfs is:

$HOME/buildroot/build_arm/root/...

So, you are saying that when I configure alsa-libs, I should be using:

CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no
--prefix=/usr

and then

make install DESTDIR=$HOME/buildroot/build_arm/root

Is this correct? I just want to make sure the libs will get into my target's rfs that way.

Thanks.

Paul

--
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

author
#13 lore raw
Quoted 66 lines · Paul Kavan

Okay:

Here is where I ran into troubles yesterday. I am working on configuring alsa-utils. When I do:

CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu

I get the error:

grhuser@pcL7:$ CC=arm-linux-gcc ./configure --target=arm-linux
--with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu
configure: WARNING: If you wanted to set the --build type, don't use
--host.
    If a cross compiler is detected then cross compile mode will be used.
checking for a BSD-compatible install... /usr/bin/install -c
checking whether build environment is sane... yes
checking for gawk... no
checking for mawk... mawk
checking whether make sets $(MAKE)... yes
checking for i686-pc-linux-gnu-strip... no
checking for strip... strip
checking whether NLS is requested... yes
checking for msgfmt... /usr/bin/msgfmt
checking for gmsgfmt... /usr/bin/msgfmt
checking for xgettext... /usr/bin/xgettext
checking for msgmerge... /usr/bin/msgmerge
checking for style of include used by make... GNU
checking for i686-pc-linux-gnu-gcc... arm-linux-gcc
checking for C compiler default output file name... a.out
checking whether the C compiler works... yes
checking whether we are cross compiling... yes
checking for suffix of executables...
checking for suffix of object files... o
checking whether we are using the GNU C compiler... yes
checking whether arm-linux-gcc accepts -g... yes
checking for arm-linux-gcc option to accept ISO C89... none needed
checking dependency style of arm-linux-gcc... gcc3
checking build system type... i686-pc-linux-gnu
checking host system type... i686-pc-linux-gnu
checking for ld used by GCC...
/home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld
checking if the linker
(/home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld)
is GNU ld... yes
checking for shared library run path origin... done
checking for CFPreferencesCopyAppValue... no
checking for CFLocaleCopyCurrent... no
checking for GNU gettext in libc... no
checking for iconv... no, consider installing GNU libiconv
checking for GNU gettext in libintl... no
checking whether to use NLS... no
checking for i686-pc-linux-gnu-gcc... (cached) arm-linux-gcc
checking whether we are using the GNU C compiler... (cached) yes
checking whether arm-linux-gcc accepts -g... (cached) yes
checking for arm-linux-gcc option to accept ISO C89... (cached) none
needed
checking dependency style of arm-linux-gcc... (cached) gcc3
checking for a BSD-compatible install... /usr/bin/install -c
checking whether ln -s works... yes
checking for ALSA CFLAGS...
checking for ALSA LDFLAGS...  -lasound -lm -ldl -lpthread
checking for libasound headers version >= 1.0.12... not present.
configure: error: Sufficiently new version of libasound not found.
Quoted 5 lines

I know there has to be a flag or something here I need to set. Does anyone know what that might be?

Paul

I think what occurs here is that the configure script is using my cross-compilers and associated libs in

$HOME/Linux_Builds/buildroot/build_arm/staging_dir/

while the libs are actually given in

$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib/

I am looking at the README and INSTALL and do not see a solution to this.

Does anyone have a solution to this?

Thanks.

Paul

#14 lore raw

At Wed, 20 Jun 2007 10:40:51 -0500,

Quoted 77 lines · Paul Kavan
Quoted 66 lines · Paul Kavan

Okay:

Here is where I ran into troubles yesterday. I am working on configuring alsa-utils. When I do:

CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu

I get the error:

grhuser@pcL7:$ CC=arm-linux-gcc ./configure --target=arm-linux
--with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu
configure: WARNING: If you wanted to set the --build type, don't use
--host.
    If a cross compiler is detected then cross compile mode will be used.
checking for a BSD-compatible install... /usr/bin/install -c
checking whether build environment is sane... yes
checking for gawk... no
checking for mawk... mawk
checking whether make sets $(MAKE)... yes
checking for i686-pc-linux-gnu-strip... no
checking for strip... strip
checking whether NLS is requested... yes
checking for msgfmt... /usr/bin/msgfmt
checking for gmsgfmt... /usr/bin/msgfmt
checking for xgettext... /usr/bin/xgettext
checking for msgmerge... /usr/bin/msgmerge
checking for style of include used by make... GNU
checking for i686-pc-linux-gnu-gcc... arm-linux-gcc
checking for C compiler default output file name... a.out
checking whether the C compiler works... yes
checking whether we are cross compiling... yes
checking for suffix of executables...
checking for suffix of object files... o
checking whether we are using the GNU C compiler... yes
checking whether arm-linux-gcc accepts -g... yes
checking for arm-linux-gcc option to accept ISO C89... none needed
checking dependency style of arm-linux-gcc... gcc3
checking build system type... i686-pc-linux-gnu
checking host system type... i686-pc-linux-gnu
checking for ld used by GCC...
/home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld
checking if the linker
(/home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld)
is GNU ld... yes
checking for shared library run path origin... done
checking for CFPreferencesCopyAppValue... no
checking for CFLocaleCopyCurrent... no
checking for GNU gettext in libc... no
checking for iconv... no, consider installing GNU libiconv
checking for GNU gettext in libintl... no
checking whether to use NLS... no
checking for i686-pc-linux-gnu-gcc... (cached) arm-linux-gcc
checking whether we are using the GNU C compiler... (cached) yes
checking whether arm-linux-gcc accepts -g... (cached) yes
checking for arm-linux-gcc option to accept ISO C89... (cached) none
needed
checking dependency style of arm-linux-gcc... (cached) gcc3
checking for a BSD-compatible install... /usr/bin/install -c
checking whether ln -s works... yes
checking for ALSA CFLAGS...
checking for ALSA LDFLAGS...  -lasound -lm -ldl -lpthread
checking for libasound headers version >= 1.0.12... not present.
configure: error: Sufficiently new version of libasound not found.
Quoted 5 lines

I know there has to be a flag or something here I need to set. Does anyone know what that might be?

Paul

I think what occurs here is that the configure script is using my cross-compilers and associated libs in

Quoted 7 lines

$HOME/Linux_Builds/buildroot/build_arm/staging_dir/

while the libs are actually given in

$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib/

I am looking at the README and INSTALL and do not see a solution to this.

For configure script using AM_PATH_ALSA(), you can pass the following options:
--with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include --with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib

Takashi

author
#15 lore raw
Quoted 8 lines

--with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include

--with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib

Takashi

Takashi:

Thank you. That got me a little further. Now, I am hitting this error:

...
checking for libasound headers version >= 1.0.12... found. checking for snd_ctl_open in -lasound... yes checking how to run the C preprocessor... arm-linux-gcc -E checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E
checking for ANSI C header files... yes
checking for initscr in -lncurses... no
checking for initscr in -lcurses... no
configure: error: this packages requires a curses library

...which I could swear I have....will look into this.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
#16 lore raw

FWIW, alsamixer is the only thing that needs curses, when I did an embedded linux + ALSA project I just passed --disable-alsamixer to work around it, and used amixer.

Lee

Quoted 41 lines · Paul Kavan
Quoted 8 lines

--with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include

--with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib

Takashi

Takashi:

Thank you. That got me a little further. Now, I am hitting this error:

...
checking for libasound headers version >= 1.0.12... found. checking for snd_ctl_open in -lasound... yes checking how to run the C preprocessor... arm-linux-gcc -E checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E
checking for ANSI C header files... yes
checking for initscr in -lncurses... no
checking for initscr in -lcurses... no
configure: error: this packages requires a curses library

...which I could swear I have....will look into this.

Paul
--
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

author
#17 lore raw
Quoted 6 lines · Lee Revell

FWIW, alsamixer is the only thing that needs curses, when I did an embedded linux + ALSA project I just passed --disable-alsamixer to work around it, and used amixer.

Lee

Lee:

Thanks. I do not think I need a mixer at all...doing mono voice on a dumb single channel codec.

Thanks again.

Paul

#18 lore raw

At Wed, 20 Jun 2007 11:18:13 -0500,

Quoted 8 lines · Paul Kavan

On 6/20/07, Lee Revell <[email protected]> wrote:

FWIW, alsamixer is the only thing that needs curses, when I did an embedded linux + ALSA project I just passed --disable-alsamixer to work around it, and used amixer.

Quoted 6 lines

Lee

Lee:

Thanks. I do not think I need a mixer at all...doing mono voice on a dumb single channel codec.

BTW, you can try salsa-lib for such a purpose:

ftp://ftp.suse.com/pub/people/tiwai/salsa-lib/

I've not tested with ARM, so it'd be appreciated if someone lets me know whether it works.

Takashi

author
#19 lore raw

Gentleman:

I have the alsa-libs and alsa-utils on my board now. I want to thank all for the time and advice.

For the benefit of the archives, I have a at91sam9260ek running Linux 2.6.22-rc1. I am using buildroot to for my cross-compiling tools and to generate my rfs. To get the alsa libs and utils on board, I did the following:

For alsa-libs:
CC=arm-linux-gcc ./configure --target=arm-linux --host=i686-pc-linux-gnu --prefix=/usr

and then
make install DESTDIR=$HOME/buildroot/build_arm/root/

where the rfs for my target is built in $HOME/buildroot/build_arm/root before making the image.

For alsa-utils:
CC=arm-linux-gcc ./configure --target=arm-linux --host=i686-pc-linux-gnu --prefix=/usr --with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include --with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib --disable-alsamixer

and then
make install DESTDIR=/home/grhuser/buildroot/build_arm/root/

Then I remade the image and booted my board. I do not have the nodes built automatically yet, so I had to do that....giving me:

/dev/snd $ ls -l

crw-rw-rw-    1 root     root     116,   0 Dec 31 17:08 controlC0
crw-rw-rw-    1 root     root     116,  24 Dec 31 17:09 pcmC0D0c
crw-rw-rw-    1 root     root     116,  16 Dec 31 17:10 pcmC0D0p

when I check with aplay, I get:

/dev/snd $ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: GRHEKW6811 [GRH_EK_W6811], device 0: W6811 W6811-PCM-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0

and with arecord:
/dev/snd $ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: GRHEKW6811 [GRH_EK_W6811], device 0: W6811 W6811-PCM-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0

However, I have been unable to achieve any kind of playback using speaker-test or aplay. The speaker pops like it wants to play, but I get the following when trying speaker test:

/dev/snd $ speaker-test -D default -r 8000 -f 1020 -F S8

speaker-test 1.0.14

Playback device is default
Stream parameters are 8000Hz, S8, 1 channels Using 16 octaves of pink noise
Rate set to 8000Hz (requested 8000Hz)
Buffer size range from 64 to 32768
Period size range from 32 to 8192
Using max buffer size 32768
Periods = 4
was set period_size = 0
was set buffer_size = 32768
Unable to set sw params for playback: Invalid argument Setting of swparams failed: Invalid argument /dev/snd $

Anyone know where I should look for the problem?

Thanks.

Paul

***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************

#20 lore raw

Paul Kavan wrote:

...

Quoted 3 lines

For alsa-libs:
CC=arm-linux-gcc ./configure --target=arm-linux --host=i686-pc-linux-gnu --prefix=/usr

...

Quoted 23 lines

However, I have been unable to achieve any kind of playback using speaker-test or aplay. The speaker pops like it wants to play, but I get the following when trying speaker test:

/dev/snd $ speaker-test -D default -r 8000 -f 1020 -F S8

speaker-test 1.0.14

Playback device is default
Stream parameters are 8000Hz, S8, 1 channels Using 16 octaves of pink noise
Rate set to 8000Hz (requested 8000Hz)
Buffer size range from 64 to 32768
Period size range from 32 to 8192
Using max buffer size 32768
Periods = 4
was set period_size = 0
was set buffer_size = 32768
Unable to set sw params for playback: Invalid argument Setting of swparams failed: Invalid argument /dev/snd $

Quoted 1 line

Anyone know where I should look for the problem?

Hi Paul,

Try adding the option "--with-versioned=no" to the alsa-libs configure.

../fam

Signature · 3 lines
Frank Mandarino                                fmandarino(a)endrelia.com
Endrelia Technologies Inc.
Toronto, Ontario, Canada
author
#21 lore raw

Frank:

Try adding the option "--with-versioned=no" to the alsa-libs configure.

That did the trick in terms of the sw params problem. With the default alsa.conf file, I can now get the speaker to make some noise. However, doing:

speaker-test -r8000 -f1000 -FS8 -tsine -l5

gives me a slightly distorted sine wave that has a period of half of what I would expect.

Frank, this is what I have for the small conf. I hope it is the right one:

pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}

ctl.w6811 {
type hw
card 0
}
pcm.w6811 {
type hw
card 0
device 0
subdevice 0
}

ctl.!default = ctl.w6811
pcm.!default = pcm.w6811

ctl.hw {
       @args[ CARD ]
       @args.CARD {
               type string
               default "0"
       }
       type hw
       card $CARD
}
pcm.hw {
       @args[ CARD DEV SUBDEV ]
       @args.CARD {
               type string
               default "0"
       }
       @args.DEV {
               type integer
               default 0
       }
       @args.SUBDEV {
               type integer
               default 0
       }
       type hw
       card $CARD
       device $DEV
       subdevice $SUBDEV
}

However, when I use this as the conf, I get the following with aplay -l

/usr/share/alsa $ aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib conf.c:975:(parse_value) card is not a string
ALSA lib conf.c:1588:(snd_config_load1) _toplevel_:45:1:Invalid argument ALSA lib conf.c:3066:(snd_config_update_r) /usr/share/alsa/alsa.conf may be old or corrupted: consit
aplay: device_list:213: control open (0): Invalid argument

Not sure if I have the alsa.conf correct. So maybe it is a problem there. You mentioned a bare bones .conf, but I do not this is the only one I have in my email.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
#22 lore raw
Quoted 6 lines · Paul Kavan

Frank:

Try adding the option "--with-versioned=no" to the alsa-libs configure.

Quoted 8 lines

That did the trick in terms of the sw params problem. With the default alsa.conf file, I can now get the speaker to make some noise. However, doing:

speaker-test -r8000 -f1000 -FS8 -tsine -l5

gives me a slightly distorted sine wave that has a period of half of what I would expect.

Better than no sound :) At least something is getting through ALSA and ASoC to your codec.

You may need to adjust the RCMR, RFRM, TCMR, TFRM register settings in sound/soc/at91/at91-ssc.c to send the data in the mode that your codec expects. I have only tested I2S and DSP_A modes with S16_LE data. It's fairly easy to add new modes.

Quoted 78 lines

Frank, this is what I have for the small conf. I hope it is the right one:

pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}

ctl.w6811 {
type hw
card 0
}
pcm.w6811 {
type hw
card 0
device 0
subdevice 0
}

ctl.!default = ctl.w6811
pcm.!default = pcm.w6811

ctl.hw {
       @args[ CARD ]
       @args.CARD {
               type string
               default "0"
       }
       type hw
       card $CARD
}
pcm.hw {
       @args[ CARD DEV SUBDEV ]
       @args.CARD {
               type string
               default "0"
       }
       @args.DEV {
               type integer
               default 0
       }
       @args.SUBDEV {
               type integer
               default 0
       }
       type hw
       card $CARD
       device $DEV
       subdevice $SUBDEV
}

However, when I use this as the conf, I get the following with aplay -l

/usr/share/alsa $ aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib conf.c:975:(parse_value) card is not a string
ALSA lib conf.c:1588:(snd_config_load1) _toplevel_:45:1:Invalid argument ALSA lib conf.c:3066:(snd_config_update_r) /usr/share/alsa/alsa.conf may be old or corrupted: consit
aplay: device_list:213: control open (0): Invalid argument

Quoted 3 lines

Not sure if I have the alsa.conf correct. So maybe it is a problem there. You mentioned a bare bones .conf, but I do not this is the only one I have in my email.

I don't see anything wrong with this alsa.conf, but I'm no expert. It is virtually the same as the one I am using, but I am using ALSA 1.0.13.

Here is the bare-bones config file that I was using before I added a second sound device:

pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}

../fam

Signature · 3 lines
Frank Mandarino                                fmandarino(a)endrelia.com
Endrelia Technologies Inc.
Toronto, Ontario, Canada
author
#23 lore raw

Frank:

Quoted 5 lines

gives me a slightly distorted sine wave that has a period of half of

Quoted 1 line

what I would expect.

Better than no sound :) At least something is getting through ALSA and ASoC to your codec.

Very true indeed. It was nice hearing a sine wave come out....even if it was not ready for prime time.

You may need to adjust the RCMR, RFRM, TCMR, TFRM register settings in

Quoted 3 lines

sound/soc/at91/at91-ssc.c to send the data in the mode that your codec expects. I have only tested I2S and DSP_A modes with S16_LE data. It's fairly easy to add new modes.

I will do this. I can probe the clock and data lines to make sure they are looking like what I expect and then look to the modes to see what I need to change in the directories.

Quoted 13 lines

Here is the bare-bones config file that I was using before I added a second sound device:

pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}

Quoted 8 lines

ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}

I will give this conf a whirl and see what it does.

Thanks.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
author
#24 lore raw
Quoted 6 lines

You may need to adjust the RCMR, RFRM, TCMR, TFRM register settings in

Quoted 3 lines

sound/soc/at91/at91- ssc.c to send the data in the mode that your codec expects. I have only tested I2S and DSP_A modes with S16_LE data. It's fairly easy to add new modes.

This is certainly part of the problem. I probed the clocks and the frame sync lines and they are fine for the most part. However, I can tell from the output that I need to change the default on TD0 to '1' for starters. I also think that I need to change the format so that the atmel board reads on the falling edge after sync. I think it already writes on the rising edge, but will have to see. Also, the width of the sync is one period of the bitclock....and I need at least two, so I will need to change that.

Fortunately, I have done a lot of grunt work already in writing my basic ssc driver for that codec. Now I have to dig into at91-ssc.c to see how to modify that.

Quoted 10 lines
Quoted 10 lines

pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}

Quoted 10 lines
Quoted 8 lines

ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}

The bare bones conf is not working for me and I am getting:

/usr/share/alsa $ aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib conf.c:3949:(snd_config_expand) Unknown parameters 0 ALSA lib control.c:909:(snd_ctl_open_noupdate) Invalid CTL hw:0
aplay: device_list:213: control open (0): Invalid argument

For whatever reason, the default conf file is letting me use speaker-test, so I can work on debugging the format for now. I am using alsa-lib-1.0.14aand alsa-utils-1.0.14, so I am not sure if that makes a difference. If anyone on the list has a bare bones conf for a simple pcm codec, I would appreciate some tips on why this one is not working.

Thanks Frank. I am gonna dig into at91-ssc.c now.

Paul

Signature · 7 lines
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************