Using aplay and arecord on an ARM
Liam:
I have managed to get the alsa-libs and aplay, arecord, and speaker-test on my board, but I am unsure how to get them to play. I have tried making the device nodes and am using a simple alsa.conf, but still no joy. I am sure there is something simple I am missing.
Trying to find some documentation on this. I am assuming there is some disconnect between the interface and my conf file. I have my alsa.conf file in /usr/share/alsa/ and it is:
pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}
ctl.w6811 {
type hw
card 0
}
pcm.w6811 {
type hw
card 0
device 0
subdevice 0
}
ctl.!default = ctl.w6811
pcm.!default = pcm.w6811
ctl.hw {
@args[ CARD ]
@args.CARD {
type string
default "0"
}
type hw
card $CARD
}pcm.hw {
@args[ CARD DEV SUBDEV ]
@args.CARD {
type string
default "0"
}
@args.DEV {
type integer
default 0
}
@args.SUBDEV {
type integer
default 0
}
type hw
card $CARD
device $DEV
subdevice $SUBDEV
}I have some /proc/ entries:
/proc/asound $ ls
GRHEKW6811 cards pcm version card0 devices timers
/proc/asound $ cat cards
0 [GRHEKW6811 ]: W6811 - GRH_EK_W6811
GRH_EK_W6811 (W6811)
/proc/asound $ cat devices
0: [ 0] : control
16: [ 0- 0]: digital audio playback
24: [ 0- 0]: digital audio capture
33: : timer
/proc/asound $ cat pcm
00-00: W6811 W6811-PCM-0 : : playback 1 : capture 1
/proc/asound $ cat timers
G0: system timer : 10000.000us (10000000 ticks)
P0-0-0: PCM playback 0-0-0 : SLAVE
P0-0-1: PCM capture 0-0-1 : SLAVE
/proc/asound $ cat version
Advanced Linux Sound Architecture Driver Version 1.0.14rc4 (Wed May 09 09:51:39.
Now, into GRHEKW6811 (which takes me to card0) I get a pcm0c and pcm0p directory. Using cat info, I get:
/proc/asound/card0/pcm0c $ cat info
card: 0
device: 0
subdevice: 0
stream: CAPTURE
id: W6811 W6811-PCM-0
name:
subname: subdevice #0
class: 0
subclass: 0subdevices_count: 1subdevices_avail: 1
/proc/asound/card0/pcm0c $ cd ../pcm0p//proc/asound/card0/pcm0p $ cat info
card: 0
device: 0
subdevice: 0
stream:
PLAYBACK
id: W6811
W6811-PCM-0
name:
subname: subdevice
#0
class:
0
subclass:
0subdevices_count:
1subdevices_avail: 1
I then did:
mknod -m 666 /dev/snd/pcm0p c 116 0
mknod -m 666 /dev/snd/pcm0c c 116 0
However, when I try speaker-test, I get:
/usr/lib/bin $ ./speaker-test -D pcm0p
speaker-test 1.0.14
Playback device is pcm0p
Stream parameters are 48000Hz, S16_LE, 1 channels Using 16 octaves of pink noise
ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM pcm0p Playback open error: -2,No such file or directory
Same for default:
/usr/lib/bin $ ./speaker-test -D
default
speaker-test 1.0.14
Playback device is
default
Stream parameters are 48000Hz, S16_LE, 1 channels
Using 16 octaves of pink
noise
ALSA lib pcm.c:2144:(snd_pcm_open_noupdate) Unknown PCM default
Playback open error: -2,No such file or directory
When I try aplay -l and arecord -l, I get:
/usr/lib/bin $ ./aplay
-l
aplay: device_list:204: no soundcards
found.../usr/lib/bin $ ./arecord
-l
arecord: device_list:204: no soundcards found...
I am at a loss here. Anyone have any advice, pointers, tips, etc......
Thanks.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
Quoted 4 lines · Paul Kavan
I have managed to get the alsa-libs and aplay, arecord, and speaker-test on my board, but I am unsure how to get them to play. I have tried making the device nodes and am using a simple alsa.conf, but still no joy. I am sure there is something simple I am missing.
What does "strace aplay file.wav" output?
Lee
Quoted 5 lines · Lee Revell
Quoted 1 line · Paul Kavan
I have managed to get the alsa-libs and aplay, arecord, and speaker-test
on
Quoted 1 line
my board, but I am unsure how to get them to play. I have tried making
Quoted 9 lines
the
Quoted 1 line
device nodes and am using a simple alsa.conf, but still no joy. I am
sure
Quoted 1 line
there is something simple I am missing.
What does "strace aplay file.wav" output?
Lee
Here is the output of strace aplay Noise.wav:
/usr/lib/share/sounds/alsa $ strace aplay Noise.wav execve("/usr/sbin/aplay", ["aplay", "Noise.wav"], [/* 7 vars */]) = 0 mmap2(NULL, 20, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40005000stat("/etc/ld.so.cache", {st_mode=S_IFREG|0644, st_size=1150, ...}) = 0open("/etc/ld.so.cache", O_RDONLY) = 3mmap2(NULL, 1150, PROT_READ, MAP_SHARED, 3, 0) = 0x40006000
close(3) = 0open("/usr/lib/libasound.so.2", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0755, st_size=770500, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0\24\373\1"..., 4096) = 4096mmap2(NULL, 770048, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x4000e000mmap2(0x4000e000, 752456, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x4000e000mmap2(0x400c6000, 15744, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xb8) = 0x400c6000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libm.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0t\22\0\000"..., 4096) = 4096mmap2(NULL, 81920, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400ca000 mmap2(0x400ca000, 41428, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400ca000mmap2(0x400dc000, 4100, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400dc000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libdl.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0(\10\0\000"..., 4096) = 4096mmap2(NULL, 40960, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400de000 mmap2(0x400de000, 5760, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400de000mmap2(0x400e7000, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x1) = 0x400e7000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libpthread.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0D<\0\0004"..., 4096) = 4096mmap2(NULL, 106496, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400e8000mmap2(0x400e8000, 40952, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400e8000mmap2(0x400fa000, 21732, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400fa000mmap2(0x40100000, 5788, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x401000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libgcc_s.so.1", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0X\25\0\000"..., 4096) = 4096mmap2(NULL, 65536, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40102000 mmap2(0x40102000, 28800, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40102000mmap2(0x40111000, 548, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x7) = 0x40111000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0000\253\0"..., 4096) = 4096mmap2(NULL, 360448, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40112000mmap2(0x40112000, 302380, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40112000mmap2(0x40164000, 5172, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x4a) = 0x40164000mmap2(0x40166000, 16020, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x40160
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libm.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0
close(3) = 0open("/lib/libdl.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0
close(3) = 0open("/lib/libpthread.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0
close(3) = 0open("/lib/libgcc_s.so.1", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0munmap(0x40006000, 1150) = 0stat("/lib/ld-uClibc.so.0", {st_mode=S_IFREG|0755, st_size=21096, ...}) = 0
mprotect(0x400dc000, 4096, PROT_READ) = 0 mprotect(0x400e7000, 4096, PROT_READ) = 0 mprotect(0x400fa000, 4096, PROT_READ) = 0 mprotect(0x40164000, 4096, PROT_READ) = 0 mprotect(0x4000c000, 4096, PROT_READ) = 0
ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0getpid() = 764getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0 setrlimit(RLIMIT_STACK, {rlim_cur=2040*1024, rlim_max=RLIM_INFINITY}) = 0 rt_sigaction(SIGRTMIN, {0x400f1d70, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0
rt_sigaction(SIGRT_1, {0x400f1c98, [RTMIN], 0x4000000 /* SA_??? */}, NULL,
8) = 0rt_sigaction(SIGRT_2, {0x400f12d0, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0 rt_sigprocmask(SIG_BLOCK, [RTMIN], NULL, 8) = 0 rt_sigprocmask(SIG_UNBLOCK, [RT_1], NULL, 8) = 0
brk(0) = 0x1c000
brk(0x1d000) = 0x1d000stat("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", 0xbebe4b70) = -1 ENOENT (No)write(2, "ALSA lib ", 9ALSA lib ) = 9write(2, "pcm.c", 5pcm.c) = 5write(2, ":", 1:) = 1write(2, "2144", 42144) = 4
write(2, ":(", 2:() = 2write(2, "snd_pcm_open_noupdate", 21snd_pcm_open_noupdate) = 21write(2, ") ", 2) ) = 2write(2, "Unknown PCM ", 12Unknown PCM ) = 12write(2, "default", 7default) = 7
write(2, "\n", 1
) = 1write(2, "aplay", 5aplay) = 5write(2, ": ", 2: ) = 2write(2, "main", 4main) = 4write(2, ":", 1:) = 1write(2, "545", 3545) = 3write(2, ": ", 2: ) = 2write(2, "audio open error: ", 18audio open error: ) = 18write(2, "No such file or directory", 25No such file or directory) = 25 write(2, "\n", 1
) = 1
exit(1) = ?
Process 764 detached
Something here sticks out as a problem. There is a line:
stat("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", 0xbebe4b70) = -1
it should not be looking in this directory, but rather in "usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf
How do I change that?
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
Quoted 2 lines · Paul Kavan
it should not be looking in this directory, but rather in "
usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.conf
I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.
Lee
Quoted 10 lines · Lee Revell
Quoted 2 lines · Paul Kavan
it should not be looking in this directory, but rather in "
usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.confI struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.
Lee
Thanks Lee, I will try to hunt that down. The list archives on
http://mailman.alsa-project.org/pipermail/alsa-devel/ only go back to March....might be a fun search.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
Found a quick workaround....although I would like to clean it up. Still does not work, but gets past the not finding the alsa.conf part.
strace aplay Noise.wav now gives:
/usr/lib/share/sounds/alsa $ strace aplay Noise.wav execve("/usr/sbin/aplay", ["aplay", "Noise.wav"], [/* 7 vars */]) = 0 mmap2(NULL, 20, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40005000stat("/etc/ld.so.cache", {st_mode=S_IFREG|0644, st_size=1150, ...}) = 0open("/etc/ld.so.cache", O_RDONLY) = 3mmap2(NULL, 1150, PROT_READ, MAP_SHARED, 3, 0) = 0x40006000
close(3) = 0open("/usr/lib/libasound.so.2", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0755, st_size=770500, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0\24\373\1"..., 4096) = 4096mmap2(NULL, 770048, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x4000e000mmap2(0x4000e000, 752456, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x4000e000mmap2(0x400c6000, 15744, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xb8) = 0x400c6000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libm.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0t\22\0\000"..., 4096) = 4096mmap2(NULL, 81920, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400ca000 mmap2(0x400ca000, 41428, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400ca000mmap2(0x400dc000, 4100, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400dc000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libdl.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0(\10\0\000"..., 4096) = 4096mmap2(NULL, 40960, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400de000 mmap2(0x400de000, 5760, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400de000mmap2(0x400e7000, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x1) = 0x400e7000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libpthread.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0D<\0\0004"..., 4096) = 4096mmap2(NULL, 106496, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x400e8000mmap2(0x400e8000, 40952, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x400e8000mmap2(0x400fa000, 21732, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0xa) = 0x400fa000mmap2(0x40100000, 5788, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x401000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libgcc_s.so.1", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0X\25\0\000"..., 4096) = 4096mmap2(NULL, 65536, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40102000 mmap2(0x40102000, 28800, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40102000mmap2(0x40111000, 548, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x7) = 0x40111000
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0 mmap2(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40007000
read(3, "\177ELF\1\1\1a\0\0\0\0\0\0\0\0\3\0(\0\1\0\0\0000\253\0"..., 4096) = 4096mmap2(NULL, 360448, PROT_NONE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x40112000mmap2(0x40112000, 302380, PROT_READ|PROT_EXEC, MAP_PRIVATE|MAP_FIXED, 3, 0) = 0x40112000mmap2(0x40164000, 5172, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED, 3, 0x4a) = 0x40164000mmap2(0x40166000, 16020, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x40160
close(3) = 0
munmap(0x40007000, 4096) = 0
open("/lib/libm.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=45812, ...}) = 0
close(3) = 0open("/lib/libdl.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=8900, ...}) = 0
close(3) = 0open("/lib/libpthread.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=63852, ...}) = 0
close(3) = 0open("/lib/libgcc_s.so.1", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=44167, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0open("/lib/libc.so.0", O_RDONLY) = 3fstat(3, {st_mode=S_IFREG|0644, st_size=309840, ...}) = 0
close(3) = 0munmap(0x40006000, 1150) = 0stat("/lib/ld-uClibc.so.0", {st_mode=S_IFREG|0755, st_size=21096, ...}) = 0
mprotect(0x400dc000, 4096, PROT_READ) = 0 mprotect(0x400e7000, 4096, PROT_READ) = 0 mprotect(0x400fa000, 4096, PROT_READ) = 0 mprotect(0x40164000, 4096, PROT_READ) = 0 mprotect(0x4000c000, 4096, PROT_READ) = 0
ioctl(0, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0ioctl(1, SNDCTL_TMR_TIMEBASE or TCGETS, {B115200 opost isig icanon echo ...}) = 0getpid() = 844getrlimit(RLIMIT_STACK, {rlim_cur=8192*1024, rlim_max=RLIM_INFINITY}) = 0 setrlimit(RLIMIT_STACK, {rlim_cur=2040*1024, rlim_max=RLIM_INFINITY}) = 0 rt_sigaction(SIGRTMIN, {0x400f1d70, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0
rt_sigaction(SIGRT_1, {0x400f1c98, [RTMIN], 0x4000000 /* SA_??? */}, NULL,
8) = 0rt_sigaction(SIGRT_2, {0x400f12d0, [], 0x4000000 /* SA_??? */}, NULL, 8) = 0 rt_sigprocmask(SIG_BLOCK, [RTMIN], NULL, 8) = 0 rt_sigprocmask(SIG_UNBLOCK, [RT_1], NULL, 8) = 0
brk(0) = 0x1c000
brk(0x1d000) = 0x1d000
stat("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", {st_mode=S_IFREG|0644, st_s0 open("/home/grhuser/buildroot/build_arm/root/usr/share/alsa/alsa.conf", O_RDONLY) = 3ioctl(3, SNDCTL_TMR_TIMEBASE or TCGETS, 0xbed04b14) = -1 ENOTTY (Inappropriate ioctl for device)
brk(0x1e000) = 0x1e000read(3, "pcm.!default {\n type hw\n car"..., 4096) = 864write(2, "ALSA lib ", 9ALSA lib ) = 9write(2, "conf.c", 6conf.c) = 6write(2, ":", 1:) = 1write(2, "975", 3975) = 3
write(2, ":(", 2:() = 2write(2, "parse_value", 11parse_value) = 11write(2, ") ", 2) ) = 2write(2, "card", 4card) = 4write(2, " is not a string", 16 is not a string) = 16
write(2, "\n", 1
) = 1write(2, "ALSA lib ", 9ALSA lib ) = 9write(2, "conf.c", 6conf.c) = 6write(2, ":", 1:) = 1write(2, "1588", 41588) = 4
write(2, ":(", 2:() = 2write(2, "snd_config_load1", 16snd_config_load1) = 16write(2, ") ", 2) ) = 2write(2, "_toplevel_", 10_toplevel_) = 10write(2, ":", 1:) = 1write(2, "45", 245) = 2
write(2, ":", 1:) = 1 write(2, "1", 11) = 1 write(2, ":", 1:) = 1
write(2, "Invalid argument", 16Invalid argument) = 16
write(2, "\n", 1
) = 1
close(3) = 0write(2, "ALSA lib ", 9ALSA lib ) = 9write(2, "conf.c", 6conf.c) = 6write(2, ":", 1:) = 1write(2, "3066", 43066) = 4
write(2, ":(", 2:() = 2write(2, "snd_config_update_r", 19snd_config_update_r) = 19write(2, ") ", 2) ) = 2
write(2, "/home/grhuser/buildroot/build_ar"..., 63/home/grhuser/buildroot/build_arm/root/usr/share/3
write(2, " may be old or corrupted: consid"..., 54 may be old or corrupted:
consider to remove or f4
write(2, "\n", 1
) = 1write(2, "aplay", 5aplay) = 5write(2, ": ", 2: ) = 2write(2, "main", 4main) = 4write(2, ":", 1:) = 1write(2, "545", 3545) = 3write(2, ": ", 2: ) = 2write(2, "audio open error: ", 18audio open error: ) = 18write(2, "Invalid argument", 16Invalid argument) = 16
write(2, "\n", 1
) = 1
exit(1) = ?
Process 844 detached
Not sure if this helps, but trying to make some progress.
Paul
At Tue, 19 Jun 2007 16:31:31 -0400,
Quoted 7 lines · Lee Revell
Quoted 2 lines · Paul Kavan
it should not be looking in this directory, but rather in "
usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.confI struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.
The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.
Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.
Takashi
Build alsa-lib and alsa-utils with prefix option
--prefix=/usr
while installing give the destination directory
make install DESTDIR=$MYINSTALLDIR
Then copy the installed executables to ARM root file sytem
This should solve the issue.
Quoted 24 lines · Takashi Iwai
At Tue, 19 Jun 2007 16:31:31 -0400,
Quoted 7 lines · Lee Revell
Quoted 2 lines · Paul Kavan
it should not be looking in this directory, but rather in "
usr/share/alsa/alsa.conf". Might be why it cannot find the alsa.confI struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.
The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.
Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.
Takashi
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 13 lines · Nobin Mathew
Build alsa-lib and alsa-utils with prefix option
--prefix=/usr
while installing give the destination directory
make install DESTDIR=$MYINSTALLDIR
Then copy the installed executables to ARM root file sytem
This should solve the issue.
Quoted 21 lines
Quoted 6 lines · Takashi Iwai
At Tue, 19 Jun 2007 16:31:31 -0400,
Quoted 4 lines · Lee Revell
Quoted 2 lines · Paul Kavan
it should not be looking in this directory, but rather in "
usr/share/alsa/alsa.conf". Might be why it cannot find thealsa.conf
Quoted 13 lines
Quoted 3 lines
I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.
The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.
Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.
Takashi
Thanks Takashi and Mathew. I just want to make sure I am clear on this. I create my embedded rfs for an ARM9 processor on my host machine. The path to the rfs is:
$HOME/buildroot/build_arm/root/...
So, you are saying that when I configure alsa-libs, I should be using:
CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no
--prefix=/usr
and then
make install DESTDIR=$HOME/buildroot/build_arm/root
Is this correct? I just want to make sure the libs will get into my target's rfs that way.
Thanks.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
Yes, but take care of permissions. you need root permissions in ARM root file system.
Quoted 69 lines · Paul Kavan
Quoted 6 lines · Nobin Mathew
Build alsa-lib and alsa-utils with prefix option
--prefix=/usr
while installing give the destination directory
Quoted 13 lines
make install DESTDIR=$MYINSTALLDIR
Then copy the installed executables to ARM root file sytem
This should solve the issue.
Quoted 6 lines · Takashi Iwai
At Tue, 19 Jun 2007 16:31:31 -0400,
Quoted 4 lines · Lee Revell
Quoted 2 lines · Paul Kavan
it should not be looking in this directory, but rather in "
usr/share/alsa/alsa.conf". Might be why it cannot find thealsa.conf
Quoted 7 lines
Quoted 7 lines
Quoted 3 lines
I struggled with the exact same problem about a year ago, I don't remember the solution but it's in the list archives.
The problem is likely you pass --prefix=$MYROOT/usr or so. The prefix option should be unchanged.
Quoted 6 lines
Quoted 6 lines
Anyway, alsa-lib-1.0.14a has extra configure options, --with-configdir and --with-plugindir, with which you can specify the exact paths, independent from $prefix.
Takashi
Thanks Takashi and Mathew. I just want to make sure I am clear on this. I create my embedded rfs for an ARM9 processor on my host machine. The path to the rfs is:
$HOME/buildroot/build_arm/root/...
So, you are saying that when I configure alsa-libs, I should be using:
CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no
--prefix=/usrand then
make install DESTDIR=$HOME/buildroot/build_arm/root
Is this correct? I just want to make sure the libs will get into my target's rfs that way.
Thanks.
Paul
--
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 66 lines · Paul Kavan
Okay:
Here is where I ran into troubles yesterday. I am working on configuring alsa-utils. When I do:
CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu
I get the error:
grhuser@pcL7:$ CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu configure: WARNING: If you wanted to set the --build type, don't use --host. If a cross compiler is detected then cross compile mode will be used. checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... no checking for mawk... mawk checking whether make sets $(MAKE)... yes checking for i686-pc-linux-gnu-strip... no checking for strip... strip checking whether NLS is requested... yes checking for msgfmt... /usr/bin/msgfmt checking for gmsgfmt... /usr/bin/msgfmt checking for xgettext... /usr/bin/xgettext checking for msgmerge... /usr/bin/msgmerge checking for style of include used by make... GNU checking for i686-pc-linux-gnu-gcc... arm-linux-gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... yes checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether arm-linux-gcc accepts -g... yes checking for arm-linux-gcc option to accept ISO C89... none needed checking dependency style of arm-linux-gcc... gcc3 checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking for ld used by GCC... /home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld checking if the linker (/home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld) is GNU ld... yes checking for shared library run path origin... done checking for CFPreferencesCopyAppValue... no checking for CFLocaleCopyCurrent... no checking for GNU gettext in libc... no checking for iconv... no, consider installing GNU libiconv checking for GNU gettext in libintl... no checking whether to use NLS... no checking for i686-pc-linux-gnu-gcc... (cached) arm-linux-gcc checking whether we are using the GNU C compiler... (cached) yes checking whether arm-linux-gcc accepts -g... (cached) yes checking for arm-linux-gcc option to accept ISO C89... (cached) none needed checking dependency style of arm-linux-gcc... (cached) gcc3 checking for a BSD-compatible install... /usr/bin/install -c checking whether ln -s works... yes checking for ALSA CFLAGS... checking for ALSA LDFLAGS... -lasound -lm -ldl -lpthread checking for libasound headers version >= 1.0.12... not present. configure: error: Sufficiently new version of libasound not found.
Quoted 5 lines
I know there has to be a flag or something here I need to set. Does anyone know what that might be?
Paul
I think what occurs here is that the configure script is using my cross-compilers and associated libs in
$HOME/Linux_Builds/buildroot/build_arm/staging_dir/
while the libs are actually given in
$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib/
I am looking at the README and INSTALL and do not see a solution to this.
Does anyone have a solution to this?
Thanks.
Paul
At Wed, 20 Jun 2007 10:40:51 -0500,
Quoted 77 lines · Paul Kavan
Quoted 66 lines · Paul Kavan
Okay:
Here is where I ran into troubles yesterday. I am working on configuring alsa-utils. When I do:
CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu
I get the error:
grhuser@pcL7:$ CC=arm-linux-gcc ./configure --target=arm-linux --with-versioned=no --prefix=/usr --host=i686-pc-linux-gnu configure: WARNING: If you wanted to set the --build type, don't use --host. If a cross compiler is detected then cross compile mode will be used. checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... no checking for mawk... mawk checking whether make sets $(MAKE)... yes checking for i686-pc-linux-gnu-strip... no checking for strip... strip checking whether NLS is requested... yes checking for msgfmt... /usr/bin/msgfmt checking for gmsgfmt... /usr/bin/msgfmt checking for xgettext... /usr/bin/xgettext checking for msgmerge... /usr/bin/msgmerge checking for style of include used by make... GNU checking for i686-pc-linux-gnu-gcc... arm-linux-gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes checking whether we are cross compiling... yes checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C compiler... yes checking whether arm-linux-gcc accepts -g... yes checking for arm-linux-gcc option to accept ISO C89... none needed checking dependency style of arm-linux-gcc... gcc3 checking build system type... i686-pc-linux-gnu checking host system type... i686-pc-linux-gnu checking for ld used by GCC... /home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld checking if the linker (/home/grhuser/Linux_Builds/buildroot/build_arm/staging_dir/arm-linux-uclibc/bin/ld) is GNU ld... yes checking for shared library run path origin... done checking for CFPreferencesCopyAppValue... no checking for CFLocaleCopyCurrent... no checking for GNU gettext in libc... no checking for iconv... no, consider installing GNU libiconv checking for GNU gettext in libintl... no checking whether to use NLS... no checking for i686-pc-linux-gnu-gcc... (cached) arm-linux-gcc checking whether we are using the GNU C compiler... (cached) yes checking whether arm-linux-gcc accepts -g... (cached) yes checking for arm-linux-gcc option to accept ISO C89... (cached) none needed checking dependency style of arm-linux-gcc... (cached) gcc3 checking for a BSD-compatible install... /usr/bin/install -c checking whether ln -s works... yes checking for ALSA CFLAGS... checking for ALSA LDFLAGS... -lasound -lm -ldl -lpthread checking for libasound headers version >= 1.0.12... not present. configure: error: Sufficiently new version of libasound not found.Quoted 5 lines
I know there has to be a flag or something here I need to set. Does anyone know what that might be?
Paul
I think what occurs here is that the configure script is using my cross-compilers and associated libs in
Quoted 7 lines
$HOME/Linux_Builds/buildroot/build_arm/staging_dir/
while the libs are actually given in
$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib/
I am looking at the README and INSTALL and do not see a solution to this.
For configure script using AM_PATH_ALSA(), you can pass the following options:
--with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include --with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib
Takashi
Quoted 8 lines
--with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include
--with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib
Takashi
Takashi:
Thank you. That got me a little further. Now, I am hitting this error:
...
checking for libasound headers version >= 1.0.12... found. checking for snd_ctl_open in -lasound... yes checking how to run the C preprocessor... arm-linux-gcc -E checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E
checking for ANSI C header files... yes
checking for initscr in -lncurses... no
checking for initscr in -lcurses... no
configure: error: this packages requires a curses library
...which I could swear I have....will look into this.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
FWIW, alsamixer is the only thing that needs curses, when I did an embedded linux + ALSA project I just passed --disable-alsamixer to work around it, and used amixer.
Lee
Quoted 41 lines · Paul Kavan
Quoted 8 lines
--with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include
--with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib
Takashi
Takashi:
Thank you. That got me a little further. Now, I am hitting this error:
...
checking for libasound headers version >= 1.0.12... found. checking forsnd_ctl_openin -lasound... yes checking how to run the C preprocessor... arm-linux-gcc -E checking for grep that handles long lines and -e.../bin/grepchecking for egrep.../bin/grep-E
checking for ANSI C header files... yes
checking for initscr in -lncurses... no
checking for initscr in -lcurses... no
configure: error: this packages requires a curses library...which I could swear I have....will look into this.
Paul
--
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 6 lines · Lee Revell
FWIW, alsamixer is the only thing that needs curses, when I did an embedded linux + ALSA project I just passed --disable-alsamixer to work around it, and used amixer.
Lee
Lee:
Thanks. I do not think I need a mixer at all...doing mono voice on a dumb single channel codec.
Thanks again.
Paul
At Wed, 20 Jun 2007 11:18:13 -0500,
Quoted 8 lines · Paul Kavan
On 6/20/07, Lee Revell <[email protected]> wrote:
FWIW, alsamixer is the only thing that needs curses, when I did an embedded linux + ALSA project I just passed --disable-alsamixer to work around it, and used amixer.
Quoted 6 lines
Lee
Lee:
Thanks. I do not think I need a mixer at all...doing mono voice on a dumb single channel codec.
BTW, you can try salsa-lib for such a purpose:
ftp://ftp.suse.com/pub/people/tiwai/salsa-lib/
I've not tested with ARM, so it'd be appreciated if someone lets me know whether it works.
Takashi
Gentleman:
I have the alsa-libs and alsa-utils on my board now. I want to thank all for the time and advice.
For the benefit of the archives, I have a at91sam9260ek running Linux 2.6.22-rc1. I am using buildroot to for my cross-compiling tools and to generate my rfs. To get the alsa libs and utils on board, I did the following:
For alsa-libs:
CC=arm-linux-gcc ./configure --target=arm-linux --host=i686-pc-linux-gnu --prefix=/usr
and then
make install DESTDIR=$HOME/buildroot/build_arm/root/
where the rfs for my target is built in $HOME/buildroot/build_arm/root before making the image.
For alsa-utils:
CC=arm-linux-gcc ./configure --target=arm-linux --host=i686-pc-linux-gnu --prefix=/usr --with-alsa-inc-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/include --with-alsa-prefix=$HOME/Linux_Builds/buildroot/build_arm/root/usr/lib --disable-alsamixer
and then
make install DESTDIR=/home/grhuser/buildroot/build_arm/root/
Then I remade the image and booted my board. I do not have the nodes built automatically yet, so I had to do that....giving me:
/dev/snd $ ls -l
crw-rw-rw- 1 root root 116, 0 Dec 31 17:08 controlC0 crw-rw-rw- 1 root root 116, 24 Dec 31 17:09 pcmC0D0c crw-rw-rw- 1 root root 116, 16 Dec 31 17:10 pcmC0D0p
when I check with aplay, I get:
/dev/snd $ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: GRHEKW6811 [GRH_EK_W6811], device 0: W6811 W6811-PCM-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
and with arecord:/dev/snd $ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: GRHEKW6811 [GRH_EK_W6811], device 0: W6811 W6811-PCM-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
However, I have been unable to achieve any kind of playback using speaker-test or aplay. The speaker pops like it wants to play, but I get the following when trying speaker test:
/dev/snd $ speaker-test -D default -r 8000 -f 1020 -F S8
speaker-test 1.0.14
Playback device is default
Stream parameters are 8000Hz, S8, 1 channels Using 16 octaves of pink noise
Rate set to 8000Hz (requested 8000Hz)
Buffer size range from 64 to 32768
Period size range from 32 to 8192
Using max buffer size 32768
Periods = 4
was set period_size = 0
was set buffer_size = 32768
Unable to set sw params for playback: Invalid argument Setting of swparams failed: Invalid argument /dev/snd $
Anyone know where I should look for the problem?
Thanks.
Paul
***************************************
Paul David Kavan
Project Engineer
GRH Electronics, Inc.
402-734-4900
[email protected]
***************************************
Paul Kavan wrote:
...
Quoted 3 lines
For alsa-libs:
CC=arm-linux-gcc ./configure --target=arm-linux --host=i686-pc-linux-gnu --prefix=/usr
...
Quoted 23 lines
However, I have been unable to achieve any kind of playback using speaker-test or aplay. The speaker pops like it wants to play, but I get the following when trying speaker test:
/dev/snd$ speaker-test -D default -r 8000 -f 1020 -F S8speaker-test 1.0.14
Playback device is default
Stream parameters are 8000Hz, S8, 1 channels Using 16 octaves of pink noise
Rate set to 8000Hz (requested 8000Hz)
Buffer size range from 64 to 32768
Period size range from 32 to 8192
Using max buffer size 32768
Periods = 4
was setperiod_size= 0
was setbuffer_size= 32768
Unable to set sw params for playback: Invalid argument Setting of swparams failed: Invalid argument/dev/snd$
Quoted 1 line
Anyone know where I should look for the problem?
Hi Paul,
Try adding the option "--with-versioned=no" to the alsa-libs configure.
../fam
Signature · 3 lines
Frank Mandarino fmandarino(a)endrelia.com Endrelia Technologies Inc. Toronto, Ontario, Canada
Frank:
Try adding the option "--with-versioned=no" to the alsa-libs configure.
That did the trick in terms of the sw params problem. With the default alsa.conf file, I can now get the speaker to make some noise. However, doing:
speaker-test -r8000 -f1000 -FS8 -tsine -l5
gives me a slightly distorted sine wave that has a period of half of what I would expect.
Frank, this is what I have for the small conf. I hope it is the right one:
pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}
ctl.w6811 {
type hw
card 0
}
pcm.w6811 {
type hw
card 0
device 0
subdevice 0
}
ctl.!default = ctl.w6811
pcm.!default = pcm.w6811
ctl.hw {
@args[ CARD ]
@args.CARD {
type string
default "0"
}
type hw
card $CARD
}pcm.hw {
@args[ CARD DEV SUBDEV ]
@args.CARD {
type string
default "0"
}
@args.DEV {
type integer
default 0
}
@args.SUBDEV {
type integer
default 0
}
type hw
card $CARD
device $DEV
subdevice $SUBDEV
}However, when I use this as the conf, I get the following with aplay -l
/usr/share/alsa $ aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib conf.c:975:(parse_value) card is not a string
ALSA lib conf.c:1588:(snd_config_load1) _toplevel_:45:1:Invalid argument ALSA lib conf.c:3066:(snd_config_update_r) /usr/share/alsa/alsa.conf may be old or corrupted: consit
aplay: device_list:213: control open (0): Invalid argument
Not sure if I have the alsa.conf correct. So maybe it is a problem there. You mentioned a bare bones .conf, but I do not this is the only one I have in my email.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
Quoted 6 lines · Paul Kavan
Frank:
Try adding the option "--with-versioned=no" to the alsa-libs configure.
Quoted 8 lines
That did the trick in terms of the sw params problem. With the default alsa.conf file, I can now get the speaker to make some noise. However, doing:
speaker-test -r8000 -f1000 -FS8 -tsine -l5
gives me a slightly distorted sine wave that has a period of half of what I would expect.
Better than no sound :) At least something is getting through ALSA and ASoC to your codec.
You may need to adjust the RCMR, RFRM, TCMR, TFRM register settings in sound/soc/at91/at91-ssc.c to send the data in the mode that your codec expects. I have only tested I2S and DSP_A modes with S16_LE data. It's fairly easy to add new modes.
Quoted 78 lines
Frank, this is what I have for the small conf. I hope it is the right one:
pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}ctl.w6811 {
type hw
card 0
}
pcm.w6811 {
type hw
card 0
device 0
subdevice 0
}ctl.!default = ctl.w6811
pcm.!default = pcm.w6811ctl.hw { @args[ CARD ] @args.CARD { type string default "0" } type hw card $CARD }pcm.hw { @args[ CARD DEV SUBDEV ] @args.CARD { type string default "0" } @args.DEV { type integer default 0 } @args.SUBDEV { type integer default 0 } type hw card $CARD device $DEV subdevice $SUBDEV }However, when I use this as the conf, I get the following with aplay -l
/usr/share/alsa$ aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib conf.c:975:(parse_value) card is not a string
ALSA lib conf.c:1588:(snd_config_load1) _toplevel_:45:1:Invalid argument ALSA lib conf.c:3066:(snd_config_update_r)/usr/share/alsa/alsa.confmay be old or corrupted: consit
aplay: device_list:213: control open (0): Invalid argument
Quoted 3 lines
Not sure if I have the alsa.conf correct. So maybe it is a problem there. You mentioned a bare bones .conf, but I do not this is the only one I have in my email.
I don't see anything wrong with this alsa.conf, but I'm no expert. It is virtually the same as the one I am using, but I am using ALSA 1.0.13.
Here is the bare-bones config file that I was using before I added a second sound device:
pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}
../fam
Signature · 3 lines
Frank Mandarino fmandarino(a)endrelia.com Endrelia Technologies Inc. Toronto, Ontario, Canada
Frank:
Quoted 5 lines
gives me a slightly distorted sine wave that has a period of half of
Quoted 1 line
what I would expect.
Better than no sound :) At least something is getting through ALSA and ASoC to your codec.
Very true indeed. It was nice hearing a sine wave come out....even if it was not ready for prime time.
You may need to adjust the RCMR, RFRM, TCMR, TFRM register settings in
Quoted 3 lines
sound/soc/at91/at91-ssc.cto send the data in the mode that your codec expects. I have only tested I2S andDSP_Amodes withS16_LEdata. It's fairly easy to add new modes.
I will do this. I can probe the clock and data lines to make sure they are looking like what I expect and then look to the modes to see what I need to change in the directories.
Quoted 13 lines
Here is the bare-bones config file that I was using before I added a second sound device:
pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
Quoted 8 lines
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}
I will give this conf a whirl and see what it does.
Thanks.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************
Quoted 6 lines
You may need to adjust the RCMR, RFRM, TCMR, TFRM register settings in
Quoted 3 lines
sound/soc/at91/at91-ssc.cto send the data in the mode that your codec expects. I have only tested I2S andDSP_Amodes withS16_LEdata. It's fairly easy to add new modes.
This is certainly part of the problem. I probed the clocks and the frame sync lines and they are fine for the most part. However, I can tell from the output that I need to change the default on TD0 to '1' for starters. I also think that I need to change the format so that the atmel board reads on the falling edge after sync. I think it already writes on the rising edge, but will have to see. Also, the width of the sync is one period of the bitclock....and I need at least two, so I will need to change that.
Fortunately, I have done a lot of grunt work already in writing my basic ssc driver for that codec. Now I have to dig into at91-ssc.c to see how to modify that.
Quoted 10 lines
Quoted 10 lines
pcm.!default {
type hw
card 0
}
pcm.hw {
type hw
card 0
device 0
subdevice 0
}
Quoted 10 lines
Quoted 8 lines
ctl.!default {
type hw
card 0
}
ctl.hw {
type hw
card 0
}
The bare bones conf is not working for me and I am getting:
/usr/share/alsa $ aplay -l
**** List of PLAYBACK Hardware Devices ****
ALSA lib conf.c:3949:(snd_config_expand) Unknown parameters 0 ALSA lib control.c:909:(snd_ctl_open_noupdate) Invalid CTL hw:0
aplay: device_list:213: control open (0): Invalid argument
For whatever reason, the default conf file is letting me use speaker-test, so I can work on debugging the format for now. I am using alsa-lib-1.0.14aand alsa-utils-1.0.14, so I am not sure if that makes a difference. If anyone on the list has a bare bones conf for a simple pcm codec, I would appreciate some tips on why this one is not working.
Thanks Frank. I am gonna dig into at91-ssc.c now.
Paul
Signature · 7 lines
*************************************** Paul David Kavan Project Engineer GRH Electronics, Inc. 402-734-4900 [email protected] ***************************************