Skip to contentSkip to conversation

Bad CD disk disables IDE DMA

DISCUSSION Zoltan Boszormenyi 2 participants 4 messages Aug 15, 2007 – Aug 16, 2007 libata

lore
Share & tools
lore
#0 lore raw

Hi,

I noticed that a bad CD of mine makes DMA disabled:

hda: selected mode 0x44
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda: ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete

Every time I put the said CD into to drive and DMA is on, I get the above messages. Two things are interesting: first, it gets mounted correctly and readable and second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide

$ cat /proc/ide/amd74xx
----------AMD BusMastering IDE Configuration----------------
Driver Version:                     2.13
South Bridge:                       0000:00:04.0
Revision:                           IDE 0xa1
Highest DMA rate:                   UDMA133
BM-DMA base:                        0xf000
PCI clock:                          33.3MHz
-----------------------Primary IDE-------Secondary IDE------
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                 yes
Enabled:                      yes                  no
Simplex only:                  no                 yes
Cable Type:                   80w                 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        PIO       DMA       DMA       DMA
Address Setup:       30ns      90ns      90ns      90ns
Cmd Active:          90ns      90ns     300ns     300ns
Cmd Recovery:        30ns      30ns     300ns     300ns
Data Active:         90ns     330ns     330ns     330ns
Data Recovery:       30ns     270ns     270ns     270ns
Cycle Time:         120ns     600ns     600ns     600ns
Transfer Rate:   16.6MB/s   3.3MB/s   3.3MB/s   3.3MB/s

Best regards,
Zoltán Böszörményi

#1 lore raw

Hi Zoltan,

Quoted 21 lines · Zoltan Boszormenyi

Hi,

I noticed that a bad CD of mine makes DMA disabled:

hda: selected mode 0x44
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda: ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete

Quoted 2 lines

Every time I put the said CD into to drive and DMA is on, I get the above messages.

This might be intended.

Quoted 47 lines

Two things are interesting: first, it gets mounted correctly and readable and
second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller

    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA

Probing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide

$ cat /proc/ide/amd74xx
----------AMD BusMastering IDE Configuration----------------
Driver Version:                     2.13
South Bridge:                       0000:00:04.0
Revision:                           IDE 0xa1
Highest DMA rate:                   UDMA133
BM-DMA base:                        0xf000
PCI clock:                          33.3MHz
-----------------------Primary IDE-------Secondary IDE------
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                 yes
Enabled:                      yes                  no
Simplex only:                  no                 yes
Cable Type:                   80w                 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        PIO       DMA       DMA       DMA
Address Setup:       30ns      90ns      90ns      90ns
Cmd Active:          90ns      90ns     300ns     300ns
Cmd Recovery:        30ns      30ns     300ns     300ns
Data Active:         90ns     330ns     330ns     330ns
Data Recovery:       30ns     270ns     270ns     270ns
Cycle Time:         120ns     600ns     600ns     600ns
Transfer Rate:   16.6MB/s   3.3MB/s   3.3MB/s   3.3MB/s
Quoted 2 lines

Best regards,
Zoltán Böszörményi

Regards,
Michal

Signature · 2 lines
LOG
http://www.stardust.webpages.pl/log/
#2 lore raw

Michal Piotrowski írta:

Quoted 25 lines

Hi Zoltan,

Quoted 21 lines · Zoltan Boszormenyi

Hi,

I noticed that a bad CD of mine makes DMA disabled:

hda: selected mode 0x44
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda: ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete

Quoted 6 lines
Quoted 3 lines

Every time I put the said CD into to drive and DMA is on, I get the above messages.

This might be intended.

Might be. Note however, that there are no "cdrom_decode_status: " lines when the drive is not using DMA. The disk is the same in both cases. I don't know too much about ATAPI, but shouldn't it report the same errors no matter how the commands are passed to the drive?
I tried to make it using DMA after mounting the "faulty" disk and copying it. The same errors occured in the logs when dd started reading but it actually finished reading:

$ LANG=C dd if=/dev/hda of=image.iso bs=2048
dd: reading `/dev/hda': Input/output error
298106+0 records in
298106+0 records out
610521088 bytes (611 MB) copied, 144.349 seconds, 4.2 MB/s

The file is a bit larger than what isosize reports about it but IIRC it's expected. So, if the disk is actually faulty dd would drop dead and not able to read the disk. Or something is not quite right in the ide-cd driver. The "DMA disabled" message comes when the drive should spin up the disk. Isn't there a timeout error somewhere? Hm. Thinking about it a bit more upon mount the same is happening - before the disk is spun up the error shows up in the logs and it switches to PIO. Does it ring a bell to someone?

Quoted 47 lines
Quoted 47 lines

Two things are interesting: first, it gets mounted correctly and readable and
second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller

    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA

Probing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide

$ cat /proc/ide/amd74xx
----------AMD BusMastering IDE Configuration----------------
Driver Version:                     2.13
South Bridge:                       0000:00:04.0
Revision:                           IDE 0xa1
Highest DMA rate:                   UDMA133
BM-DMA base:                        0xf000
PCI clock:                          33.3MHz
-----------------------Primary IDE-------Secondary IDE------
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                 yes
Enabled:                      yes                  no
Simplex only:                  no                 yes
Cable Type:                   80w                 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        PIO       DMA       DMA       DMA
Address Setup:       30ns      90ns      90ns      90ns
Cmd Active:          90ns      90ns     300ns     300ns
Cmd Recovery:        30ns      30ns     300ns     300ns
Data Active:         90ns     330ns     330ns     330ns
Data Recovery:       30ns     270ns     270ns     270ns
Cycle Time:         120ns     600ns     600ns     600ns
Transfer Rate:   16.6MB/s   3.3MB/s   3.3MB/s   3.3MB/s
Quoted 8 lines
Quoted 3 lines

Best regards,
Zoltán Böszörményi

Regards,
Michal

Best regards,
Zoltán

#3 lore raw

Zoltan Boszormenyi írta:

Quoted 47 lines

Michal Piotrowski írta:

Quoted 25 lines

Hi Zoltan,

Quoted 21 lines · Zoltan Boszormenyi

Hi,

I noticed that a bad CD of mine makes DMA disabled:

hda: selected mode 0x44
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda: ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete

Quoted 6 lines
Quoted 3 lines

Every time I put the said CD into to drive and DMA is on, I get the above messages.

This might be intended.

Might be. Note however, that there are no "cdrom_decode_status: " lines when the drive is not using DMA. The disk is the same in both cases. I don't know too much about ATAPI, but shouldn't it report the same errors no matter how the commands are passed to the drive?
I tried to make it using DMA after mounting the "faulty" disk and copying it. The same errors occured in the logs when dd started reading but it actually finished reading:

$ LANG=C dd if=/dev/hda of=image.iso bs=2048
dd: reading `/dev/hda': Input/output error
298106+0 records in
298106+0 records out
610521088 bytes (611 MB) copied, 144.349 seconds, 4.2 MB/s
Quoted 7 lines

The file is a bit larger than what isosize reports about it but IIRC it's expected. So, if the disk is actually faulty dd would drop dead and not able to read the disk. Or something is not quite right in the ide-cd driver. The "DMA disabled" message comes when the drive should spin up the disk. Isn't there a timeout error somewhere? Hm. Thinking about it a bit more upon mount the same is happening - before the disk is spun up the error shows up in the logs and it switches to PIO. Does it ring a bell to someone?

Another data point: the other disks I tried up to now were DVDs and DMA remains turned on for those. It's even true for empty DVDs and the label side of a Labelflash disk. On the other hand, another CD and two other CDRW disks (no visible faults, scratches on either btw) give me the same error when they are mounted, DMA gets disabled.

... some more tests and researching ...

TADA! The solution was to tune down the drive to only use UDMA3 with "hdparm -X67". Now although dd didn't get any faster, DMA remained enabled. Actually the drive is originally a Pioneer 111D that was reflashed to 111L to get the Labelflash feature. Can it be a firmware bug? BTW the drive has a 80w cable.

Quoted 61 lines
Quoted 47 lines
Quoted 47 lines

Two things are interesting: first, it gets mounted correctly and readable and
second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller

    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA

Probing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide

$ cat /proc/ide/amd74xx
----------AMD BusMastering IDE Configuration----------------
Driver Version:                     2.13
South Bridge:                       0000:00:04.0
Revision:                           IDE 0xa1
Highest DMA rate:                   UDMA133
BM-DMA base:                        0xf000
PCI clock:                          33.3MHz
-----------------------Primary IDE-------Secondary IDE------
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                 yes
Enabled:                      yes                  no
Simplex only:                  no                 yes
Cable Type:                   80w                 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        PIO       DMA       DMA       DMA
Address Setup:       30ns      90ns      90ns      90ns
Cmd Active:          90ns      90ns     300ns     300ns
Cmd Recovery:        30ns      30ns     300ns     300ns
Data Active:         90ns     330ns     330ns     330ns
Data Recovery:       30ns     270ns     270ns     270ns
Cycle Time:         120ns     600ns     600ns     600ns
Transfer Rate:   16.6MB/s   3.3MB/s   3.3MB/s   3.3MB/s
Quoted 8 lines
Quoted 3 lines

Best regards,
Zoltán Böszörményi

Regards,
Michal

Best regards,
Zoltán