Bad CD disk disables IDE DMA
Hi,
I noticed that a bad CD of mine makes DMA disabled:
hda: selected mode 0x44
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda: ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete
Every time I put the said CD into to drive and DMA is on, I get the above messages. Two things are interesting: first, it gets mounted correctly and readable and second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
$ cat /proc/ide/amd74xx ----------AMD BusMastering IDE Configuration---------------- Driver Version: 2.13 South Bridge: 0000:00:04.0 Revision: IDE 0xa1 Highest DMA rate: UDMA133 BM-DMA base: 0xf000 PCI clock: 33.3MHz -----------------------Primary IDE-------Secondary IDE------ Prefetch Buffer: yes yes Post Write Buffer: yes yes Enabled: yes no Simplex only: no yes Cable Type: 80w 80w -------------------drive0----drive1----drive2----drive3----- Transfer Mode: PIO DMA DMA DMA Address Setup: 30ns 90ns 90ns 90ns Cmd Active: 90ns 90ns 300ns 300ns Cmd Recovery: 30ns 30ns 300ns 300ns Data Active: 90ns 330ns 330ns 330ns Data Recovery: 30ns 270ns 270ns 270ns Cycle Time: 120ns 600ns 600ns 600ns Transfer Rate: 16.6MB/s 3.3MB/s 3.3MB/s 3.3MB/s
Best regards,
Zoltán Böszörményi
Hi Zoltan,
Quoted 21 lines · Zoltan Boszormenyi
Hi,
I noticed that a bad CD of mine makes DMA disabled:
hda: selected mode
0x44
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda:ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete
Quoted 2 lines
Every time I put the said CD into to drive and DMA is on, I get the above messages.
This might be intended.
Quoted 47 lines
Two things are interesting: first, it gets mounted correctly and readable and
second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controlleride0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMAProbing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide$ cat /proc/ide/amd74xx ----------AMD BusMastering IDE Configuration---------------- Driver Version: 2.13 South Bridge: 0000:00:04.0 Revision: IDE 0xa1 Highest DMA rate: UDMA133 BM-DMA base: 0xf000 PCI clock: 33.3MHz -----------------------Primary IDE-------Secondary IDE------ Prefetch Buffer: yes yes Post Write Buffer: yes yes Enabled: yes no Simplex only: no yes Cable Type: 80w 80w -------------------drive0----drive1----drive2----drive3----- Transfer Mode: PIO DMA DMA DMA Address Setup: 30ns 90ns 90ns 90ns Cmd Active: 90ns 90ns 300ns 300ns Cmd Recovery: 30ns 30ns 300ns 300ns Data Active: 90ns 330ns 330ns 330ns Data Recovery: 30ns 270ns 270ns 270ns Cycle Time: 120ns 600ns 600ns 600ns Transfer Rate: 16.6MB/s 3.3MB/s 3.3MB/s 3.3MB/s
Quoted 2 lines
Best regards,
Zoltán Böszörményi
Regards,
Michal
Signature · 2 lines
LOG http://www.stardust.webpages.pl/log/
Michal Piotrowski írta:
Quoted 25 lines
Hi Zoltan,
Quoted 21 lines · Zoltan Boszormenyi
Hi,
I noticed that a bad CD of mine makes DMA disabled:
hda: selected mode
0x44
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda:ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset complete
Quoted 6 lines
Quoted 3 lines
Every time I put the said CD into to drive and DMA is on, I get the above messages.
This might be intended.
Might be. Note however, that there are no "cdrom_decode_status: " lines when the drive is not using DMA. The disk is the same in both cases. I don't know too much about ATAPI, but shouldn't it report the same errors no matter how the commands are passed to the drive?
I tried to make it using DMA after mounting the "faulty" disk and copying it. The same errors occured in the logs when dd started reading but it actually finished reading:
$ LANG=C dd if=/dev/hda of=image.iso bs=2048 dd: reading `/dev/hda': Input/output error 298106+0 records in 298106+0 records out 610521088 bytes (611 MB) copied, 144.349 seconds, 4.2 MB/s
The file is a bit larger than what isosize reports about it but IIRC it's expected. So, if the disk is actually faulty dd would drop dead and not able to read the disk. Or something is not quite right in the ide-cd driver. The "DMA disabled" message comes when the drive should spin up the disk. Isn't there a timeout error somewhere? Hm. Thinking about it a bit more upon mount the same is happening - before the disk is spun up the error shows up in the logs and it switches to PIO. Does it ring a bell to someone?
Quoted 47 lines
Quoted 47 lines
Two things are interesting: first, it gets mounted correctly and readable and
second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controlleride0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMAProbing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide$ cat /proc/ide/amd74xx ----------AMD BusMastering IDE Configuration---------------- Driver Version: 2.13 South Bridge: 0000:00:04.0 Revision: IDE 0xa1 Highest DMA rate: UDMA133 BM-DMA base: 0xf000 PCI clock: 33.3MHz -----------------------Primary IDE-------Secondary IDE------ Prefetch Buffer: yes yes Post Write Buffer: yes yes Enabled: yes no Simplex only: no yes Cable Type: 80w 80w -------------------drive0----drive1----drive2----drive3----- Transfer Mode: PIO DMA DMA DMA Address Setup: 30ns 90ns 90ns 90ns Cmd Active: 90ns 90ns 300ns 300ns Cmd Recovery: 30ns 30ns 300ns 300ns Data Active: 90ns 330ns 330ns 330ns Data Recovery: 30ns 270ns 270ns 270ns Cycle Time: 120ns 600ns 600ns 600ns Transfer Rate: 16.6MB/s 3.3MB/s 3.3MB/s 3.3MB/s
Quoted 8 lines
Quoted 3 lines
Best regards,
Zoltán BöszörményiRegards,
Michal
Best regards,
Zoltán
Zoltan Boszormenyi írta:
Quoted 47 lines
Michal Piotrowski írta:
Quoted 25 lines
Hi Zoltan,
Quoted 21 lines · Zoltan Boszormenyi
Hi,
I noticed that a bad CD of mine makes DMA disabled:
hda: selected mode
0x44
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hda:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hda: DMA disabled
hda:ide_intr: huh? expected NULL handler on exit
hda: ATAPI reset completeQuoted 6 lines
Quoted 3 lines
Every time I put the said CD into to drive and DMA is on, I get the above messages.
This might be intended.
Might be. Note however, that there are no "
cdrom_decode_status: " lines when the drive is not using DMA. The disk is the same in both cases. I don't know too much about ATAPI, but shouldn't it report the same errors no matter how the commands are passed to the drive?
I tried to make it using DMA after mounting the "faulty" disk and copying it. The same errors occured in the logs when dd started reading but it actually finished reading:$ LANG=C dd if=/dev/hda of=image.iso bs=2048 dd: reading `/dev/hda': Input/output error 298106+0 records in 298106+0 records out 610521088 bytes (611 MB) copied, 144.349 seconds, 4.2 MB/s
Quoted 7 lines
The file is a bit larger than what isosize reports about it but IIRC it's expected. So, if the disk is actually faulty dd would drop dead and not able to read the disk. Or something is not quite right in the ide-cd driver. The "DMA disabled" message comes when the drive should spin up the disk. Isn't there a timeout error somewhere? Hm. Thinking about it a bit more upon mount the same is happening - before the disk is spun up the error shows up in the logs and it switches to PIO. Does it ring a bell to someone?
Another data point: the other disks I tried up to now were DVDs and DMA remains turned on for those. It's even true for empty DVDs and the label side of a Labelflash disk. On the other hand, another CD and two other CDRW disks (no visible faults, scratches on either btw) give me the same error when they are mounted, DMA gets disabled.
... some more tests and researching ...
TADA! The solution was to tune down the drive to only use UDMA3 with "hdparm -X67". Now although dd didn't get any faster, DMA remained enabled. Actually the drive is originally a Pioneer 111D that was reflashed to 111L to get the Labelflash feature. Can it be a firmware bug? BTW the drive has a 80w cable.
Quoted 61 lines
Quoted 47 lines
Quoted 47 lines
Two things are interesting: first, it gets mounted correctly and readable and
second, when DMA was already disabled no such messages occur in the logs. Anyhow, I would need DMA to correctly burn CDs/DVDs...
What can I do besides manually re-enable DMA?
All other disks I have tried behave perfectly.
This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6. This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controlleride0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMAProbing IDE interface ide0...
hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide$ cat /proc/ide/amd74xx ----------AMD BusMastering IDE Configuration---------------- Driver Version: 2.13 South Bridge: 0000:00:04.0 Revision: IDE 0xa1 Highest DMA rate: UDMA133 BM-DMA base: 0xf000 PCI clock: 33.3MHz -----------------------Primary IDE-------Secondary IDE------ Prefetch Buffer: yes yes Post Write Buffer: yes yes Enabled: yes no Simplex only: no yes Cable Type: 80w 80w -------------------drive0----drive1----drive2----drive3----- Transfer Mode: PIO DMA DMA DMA Address Setup: 30ns 90ns 90ns 90ns Cmd Active: 90ns 90ns 300ns 300ns Cmd Recovery: 30ns 30ns 300ns 300ns Data Active: 90ns 330ns 330ns 330ns Data Recovery: 30ns 270ns 270ns 270ns Cycle Time: 120ns 600ns 600ns 600ns Transfer Rate: 16.6MB/s 3.3MB/s 3.3MB/s 3.3MB/sQuoted 8 lines
Quoted 3 lines
Best regards,
Zoltán BöszörményiRegards,
MichalBest regards,
Zoltán