MSCC: Add Jaguar2 SOC family
Subsystems (2)
v2 cover MSCC: Add Jaguar2 SOC family
This patch series add support for MSCC Jaguar2 SOC family. In this family there are the following boards: Jagaur2(pcb110), Jaguar2-48(pcb111) and Serval2(pcb112).
This is based off the u-boot-mips/next repository
This version address comments from Daniel Schwierzeck <[email protected]>
v2-changes:
- create sysreset driver for Jaguar2
- update pinctrl
Horatiu Vultur (7):
pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
MSCC: Add support for Jaguar2 SOC family
MSCC: Add device tree for Jaguar2 board
MSCC: Add device tree for Jaguar2-48 board
MSCC: add device tree for Serval2 board
MSCC: Add board support for Jaguar2 SOC family
MSCC: Add sysreset driver for Jaguar2 SOC family
MAINTAINERS | 4 + arch/mips/dts/Makefile | 1 + arch/mips/dts/jr2_pcb110.dts | 74 +++++ arch/mips/dts/jr2_pcb111.dts | 74 +++++ arch/mips/dts/mscc,jr2.dtsi | 187 +++++++++++ arch/mips/dts/serval2_pcb112.dts | 60 ++++ arch/mips/mach-mscc/Kconfig | 9 + arch/mips/mach-mscc/Makefile | 5 +- arch/mips/mach-mscc/cpu.c | 7 + arch/mips/mach-mscc/dram.c | 2 +- arch/mips/mach-mscc/include/mach/common.h | 5 + arch/mips/mach-mscc/include/mach/ddr.h | 38 ++- arch/mips/mach-mscc/include/mach/jr2/jr2.h | 24 ++ .../mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h | 20 ++ .../include/mach/jr2/jr2_devcpu_gcb_miim_regs.h | 25 ++ .../mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h | 321 +++++++++++++++++++ board/mscc/common/Makefile | 4 + board/mscc/common/spi.c | 31 ++ board/mscc/jr2/Kconfig | 15 + board/mscc/jr2/Makefile | 4 + board/mscc/jr2/jr2.c | 125 ++++++++ board/mscc/ocelot/ocelot.c | 22 -- configs/mscc_jr2_defconfig | 61 ++++ drivers/pinctrl/mscc/Kconfig | 9 + drivers/pinctrl/mscc/Makefile | 1 + drivers/pinctrl/mscc/mscc-common.c | 97 ++++-- drivers/pinctrl/mscc/mscc-common.h | 5 + drivers/pinctrl/mscc/pinctrl-jr2.c | 342 +++++++++++++++++++++ drivers/sysreset/Kconfig | 6 + drivers/sysreset/Makefile | 1 + drivers/sysreset/sysreset_jr2.c | 46 +++ 31 files changed, 1571 insertions(+), 54 deletions(-) create mode 100644 arch/mips/dts/jr2_pcb110.dts create mode 100644 arch/mips/dts/jr2_pcb111.dts create mode 100644 arch/mips/dts/mscc,jr2.dtsi create mode 100644 arch/mips/dts/serval2_pcb112.dts create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb_miim_regs.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h create mode 100644 board/mscc/common/Makefile create mode 100644 board/mscc/common/spi.c create mode 100644 board/mscc/jr2/Kconfig create mode 100644 board/mscc/jr2/Makefile create mode 100644 board/mscc/jr2/jr2.c create mode 100644 configs/mscc_jr2_defconfig create mode 100644 drivers/pinctrl/mscc/pinctrl-jr2.c create mode 100644 drivers/sysreset/sysreset_jr2.c
Signature · 1 line
2.7.4
PATCH v2 1/7 pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common to support new numbe of pins.
--- MAINTAINERS | 1 + drivers/pinctrl/mscc/Kconfig | 9 + drivers/pinctrl/mscc/Makefile | 1 + drivers/pinctrl/mscc/mscc-common.c | 97 ++++++++--- drivers/pinctrl/mscc/mscc-common.h | 5 + drivers/pinctrl/mscc/pinctrl-jr2.c | 342 +++++++++++++++++++++++++++++++++++++ 6 files changed, 433 insertions(+), 22 deletions(-) create mode 100644 drivers/pinctrl/mscc/pinctrl-jr2.c
MAINTAINERS +1 -0
@@ -525,6 +525,7 @@ F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c F: include/configs/vcoreiii.h +F: drivers/pinctrl/mscc/ MIPS JZ4780 M: Ezequiel Garcia <[email protected]>
drivers/pinctrl/mscc/Kconfig +9 -0
@@ -20,3 +20,12 @@ config PINCTRL_MSCC_LUTON help Support pin multiplexing and pin configuration control on Microsemi luton SoCs. + +config PINCTRL_MSCC_JR2 + depends on SOC_JR2 && PINCTRL_FULL && OF_CONTROL + select PINCTRL_MSCC + default y + bool "Microsemi jr2 family pin control driver" + help + Support pin multiplexing and pin configuration control on + Microsemi jr2 SoCs.
drivers/pinctrl/mscc/Makefile +1 -0
@@ -3,3 +3,4 @@ obj-y += mscc-common.o obj-$(CONFIG_PINCTRL_MSCC_OCELOT) += pinctrl-ocelot.o obj-$(CONFIG_PINCTRL_MSCC_LUTON) += pinctrl-luton.o +obj-$(CONFIG_PINCTRL_MSCC_JR2) += pinctrl-jr2.o
drivers/pinctrl/mscc/mscc-common.c +75 -22
184 lines not on this page · raw message
drivers/pinctrl/mscc/mscc-common.h +5 -0
@@ -43,6 +43,11 @@ struct mscc_pinctrl {char *const *function_names; }; +void mscc_setbits (unsigned int offset,void *addr); +void mscc_clrbits (unsigned int offset,void *addr); +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins); +int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins,char *const *function_names);
drivers/pinctrl/mscc/pinctrl-jr2.c new file +342 -0
342 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 1/7 pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 62 lines
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common to support new numbe of pins.
Signed-off-by Horatiu Vultur <[email protected]>--- MAINTAINERS | 1 + drivers/pinctrl/mscc/Kconfig | 9 + drivers/pinctrl/mscc/Makefile | 1 + drivers/pinctrl/mscc/mscc-common.c | 97 ++++++++--- drivers/pinctrl/mscc/mscc-common.h | 5 + drivers/pinctrl/mscc/pinctrl-jr2.c | 342 +++++++++++++++++++++++++++++++++++++ 6 files changed, 433 insertions(+), 22 deletions(-) create mode 100644 drivers/pinctrl/mscc/pinctrl-jr2.cMAINTAINERS +1
-0@@ -525,6 +525,7 @@ F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c F: include/configs/vcoreiii.h +F: drivers/pinctrl/mscc/ MIPS JZ4780 M: Ezequiel Garcia <[email protected]>drivers/pinctrl/mscc/Kconfig +9
-0@@ -20,3 +20,12 @@ config PINCTRL_MSCC_LUTON help Support pin multiplexing and pin configuration control on Microsemi luton SoCs. + +config PINCTRL_MSCC_JR2 + depends on SOC_JR2 && PINCTRL_FULL && OF_CONTROL + select PINCTRL_MSCC + default y + bool "Microsemi jr2 family pin control driver" + help + Support pin multiplexing and pin configuration control on + Microsemi jr2 SoCs.drivers/pinctrl/mscc/Makefile +1
-0@@ -3,3 +3,4 @@ obj-y += mscc-common.o obj-$(CONFIG_PINCTRL_MSCC_OCELOT) += pinctrl-ocelot.o obj-$(CONFIG_PINCTRL_MSCC_LUTON) += pinctrl-luton.o +obj-$(CONFIG_PINCTRL_MSCC_JR2) += pinctrl-jr2.odrivers/pinctrl/mscc/mscc-common.c +2
-0@@ -22,6 +22,18 @@#include <linux/io.h> #include "mscc-common.h" +#if defined(CONFIG_SOC_JR2 ) +#define MSCC_GPIO_OUT_SET 0x00
drivers/pinctrl/mscc/mscc-common.c line 36
Quoted 10 lines
drivers/pinctrl/mscc/mscc-common.c +10
-0+#define MSCC_GPIO_OUT_CLR 0x08 +#define MSCC_GPIO_OUT 0x10 +#define MSCC_GPIO_IN 0x18 +#define MSCC_GPIO_OE 0x20 +#define MSCC_GPIO_INTR 0x28 +#define MSCC_GPIO_INTR_ENA 0x30 +#define MSCC_GPIO_INTR_IDENT 0x38 +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 +#else
you should also move this to pinctrl-jr2.c
Quoted 170 lines
drivers/pinctrl/mscc/mscc-common.c +62
-21#define MSCC_GPIO_OUT_SET 0x0#define MSCC_GPIO_OUT_CLR 0x4#define MSCC_GPIO_OUT 0x8@@ -32,6 +44,39 @@#define MSCC_GPIO_INTR_IDENT 0x1c#define MSCC_GPIO_ALT0 0x20#define MSCC_GPIO_ALT1 0x24 +#endif + +static void mscc_writel (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (BIT (offset), addr); +else +writel (BIT (offset %32 ), addr +4 ); +} + +static unsigned int mscc_readl (unsigned int offset,void *addr) +{ +if (offset <32 ) +return readl (addr); +else +return readl (addr +4 ); +} + +void mscc_setbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) |BIT (offset), addr); +else +writel (readl (addr +4 ) |BIT (offset %32 ), addr +4 ); +} + +void mscc_clrbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) & ~BIT (offset), addr); +else +writel (readl (addr +4 ) & ~BIT (offset %32 ), addr +4 ); +}static int mscc_get_functions_count (struct udevice *dev) {@@ -48,8 +93,8 @@ static const char *mscc_get_function_name(struct udevice *dev,return info->function_names[function]; } -static int mscc_pin_function_idx (unsigned int pin,unsigned int function, -const struct mscc_pin_data *mscc_pins) +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins) {struct mscc_pin_caps *p = mscc_pins[pin].drv_data;int i;@@ -62,7 +107,7 @@ static int mscc_pin_function_idx(unsigned int pin, unsigned int function,return -1 ; } -static int mscc_pinmux_set_mux (struct udevice *dev, +__weak int mscc_pinmux_set_mux (struct udevice *dev,unsigned int pin_selector,unsigned int selector) {struct mscc_pinctrl *info =dev_get_priv (dev);@@ -79,15 +124,16 @@ static int mscc_pinmux_set_mux(struct udevice *dev,* This is racy because both registers can't be updated at the same time * but it doesn't matter much for now. */ +if (f &BIT (0 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );if (f &BIT (1 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );return 0 ; }@@ -120,8 +166,8 @@ static int mscc_create_group_func_map(struct udevice *dev, } info->func[f].ngroups = npins; - info->func[f].groups =devm_kzalloc (dev, npins * -sizeof (char *),GFP_KERNEL ); + info->func[f].groups =devm_kzalloc (dev, npins *sizeof (char *), +GFP_KERNEL );if (!info->func[f].groups)return -ENOMEM ;@@ -132,7 +178,8 @@ static int mscc_create_group_func_map(struct udevice *dev,return 0 ; } -static int mscc_pinctrl_register (struct udevice *dev,struct mscc_pinctrl *info) +static int mscc_pinctrl_register (struct udevice *dev, +struct mscc_pinctrl *info) {int ret;@@ -150,38 +197,44 @@ static int mscc_gpio_get(struct udevice *dev, unsigned int offset)struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_IN ); +if (mscc_readl (offset, info->regs +MSCC_GPIO_OE ) &BIT (offset %32 )) + val =mscc_readl (offset, info->regs +MSCC_GPIO_OUT ); +else + val =mscc_readl (offset, info->regs +MSCC_GPIO_IN ); -return !!(val &BIT (offset)); +return !!(val &BIT (offset %32 )); } -static int mscc_gpio_set (struct udevice *dev,unsigned int offset,int value) +static int mscc_gpio_set (struct udevice *dev,unsigned int offset, +int value) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);if (value) -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_SET ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_SET );else -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_CLR ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_CLR );return 0 ; } -static int mscc_gpio_get_direction (struct udevice *dev,unsigned int offset) +static int mscc_gpio_get_direction (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_OE ); + val =mscc_readl (offset, info->regs +MSCC_GPIO_OE ); -return (val &BIT (offset)) ?GPIOF_OUTPUT :GPIOF_INPUT ; +return (val &BIT (offset %32 )) ?GPIOF_OUTPUT :GPIOF_INPUT ; } -static int mscc_gpio_direction_input (struct udevice *dev,unsigned int offset) +static int mscc_gpio_direction_input (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -clrbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_clrbits (offset, info->regs +MSCC_GPIO_OE );return 0 ; }@@ -191,7 +244,7 @@ static int mscc_gpio_direction_output(struct udevice *dev, {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -setbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_setbits (offset, info->regs +MSCC_GPIO_OE );return mscc_gpio_set (dev, offset, value); }
drivers/pinctrl/mscc/mscc-common.c const struct pinctrl_ops mscc_pinctrl_ops = { · line 271
Quoted 5 lines
drivers/pinctrl/mscc/mscc-common.c +1
-1@@ -215,7 +268,7 @@ const struct pinctrl_ops mscc_pinctrl_ops = {int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins, -char *const *function_names) +char *const *function_names)
missing space: char * const *function_names
Quoted 25 lines
drivers/pinctrl/mscc/mscc-common.c +0
-0{struct mscc_pinctrl *priv =dev_get_priv (dev);int ret;drivers/pinctrl/mscc/mscc-common.h +5
-0@@ -43,6 +43,11 @@ struct mscc_pinctrl {char *const *function_names; }; +void mscc_setbits (unsigned int offset,void *addr); +void mscc_clrbits (unsigned int offset,void *addr); +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins); +int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins,char *const *function_names);drivers/pinctrl/mscc/pinctrl-jr2.c new file +0
-0
drivers/pinctrl/mscc/pinctrl-jr2.c line 6
Quoted 6 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +6
-0@@ -0,0 +1,342 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* +* Microsemi SoCs pinctrl driver +* +* Author: <[email protected]> +* License: Dual MIT/GPL
license is redundant due to SPDX
Quoted 337 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +336
-0+* Copyright (c) 2018 Microsemi Corporation +*/ + +#include <common.h> +#include <config.h> +#include <dm.h> +#include <dm/device-internal.h> +#include <dm/lists.h> +#include <dm/pinctrl.h> +#include <dm/root.h> +#include <errno.h> +#include <fdtdec.h> +#include <linux/io.h> +#include <asm/gpio.h> +#include <asm/system.h> +#include "mscc-common.h" + +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 + +enum { +FUNC_NONE , +FUNC_GPIO , +FUNC_IRQ0_IN , +FUNC_IRQ0_OUT , +FUNC_IRQ1_IN , +FUNC_IRQ1_OUT , +FUNC_MIIM1 , +FUNC_MIIM2 , +FUNC_PCI_WAKE , +FUNC_PTP0 , +FUNC_PTP1 , +FUNC_PTP2 , +FUNC_PTP3 , +FUNC_PWM , +FUNC_RECO_CLK0 , +FUNC_RECO_CLK1 , +FUNC_SFP0 , +FUNC_SFP1 , +FUNC_SFP2 , +FUNC_SFP3 , +FUNC_SFP4 , +FUNC_SFP5 , +FUNC_SFP6 , +FUNC_SFP7 , +FUNC_SFP8 , +FUNC_SFP9 , +FUNC_SFP10 , +FUNC_SFP11 , +FUNC_SFP12 , +FUNC_SFP13 , +FUNC_SFP14 , +FUNC_SFP15 , +FUNC_SIO , +FUNC_SIO1 , +FUNC_SIO2 , +FUNC_SI , +FUNC_TACHO , +FUNC_TWI , +FUNC_TWI2 , +FUNC_TWI_SCL_M , +FUNC_UART , +FUNC_UART2 , +FUNC_MAX +}; + +char *jr2_function_names[] = { + [FUNC_NONE ] ="none" , + [FUNC_GPIO ] ="gpio" , + [FUNC_IRQ0_IN ] ="irq0_in" , + [FUNC_IRQ0_OUT ] ="irq0_out" , + [FUNC_IRQ1_IN ] ="irq1_in" , + [FUNC_IRQ1_OUT ] ="irq1_out" , + [FUNC_MIIM1 ] ="miim1" , + [FUNC_MIIM2 ] ="miim2" , + [FUNC_PCI_WAKE ] ="pci_wake" , + [FUNC_PTP0 ] ="ptp0" , + [FUNC_PTP1 ] ="ptp1" , + [FUNC_PTP2 ] ="ptp2" , + [FUNC_PTP3 ] ="ptp3" , + [FUNC_PWM ] ="pwm" , + [FUNC_RECO_CLK0 ] ="reco_clk0" , + [FUNC_RECO_CLK1 ] ="reco_clk1" , + [FUNC_SFP0 ] ="sfp0" , + [FUNC_SFP1 ] ="sfp1" , + [FUNC_SFP2 ] ="sfp2" , + [FUNC_SFP3 ] ="sfp3" , + [FUNC_SFP4 ] ="sfp4" , + [FUNC_SFP5 ] ="sfp5" , + [FUNC_SFP6 ] ="sfp6" , + [FUNC_SFP7 ] ="sfp7" , + [FUNC_SFP8 ] ="sfp8" , + [FUNC_SFP9 ] ="sfp9" , + [FUNC_SFP10 ] ="sfp10" , + [FUNC_SFP11 ] ="sfp11" , + [FUNC_SFP12 ] ="sfp12" , + [FUNC_SFP13 ] ="sfp13" , + [FUNC_SFP14 ] ="sfp14" , + [FUNC_SFP15 ] ="sfp15" , + [FUNC_SIO ] ="sio" , + [FUNC_SIO1 ] ="sio1" , + [FUNC_SIO2 ] ="sio2" , + [FUNC_SI ] ="si" , + [FUNC_TACHO ] ="tacho" , + [FUNC_TWI ] ="twi" , + [FUNC_TWI2 ] ="twi2" , + [FUNC_TWI_SCL_M ] ="twi_scl_m" , + [FUNC_UART ] ="uart" , + [FUNC_UART2 ] ="uart2" , +}; + +MSCC_P (0 ,SIO ,NONE ,NONE ); +MSCC_P (1 ,SIO ,NONE ,NONE ); +MSCC_P (2 ,SIO ,NONE ,NONE ); +MSCC_P (3 ,SIO ,NONE ,NONE ); +MSCC_P (4 ,SIO1 ,NONE ,NONE ); +MSCC_P (5 ,SIO1 ,NONE ,NONE ); +MSCC_P (6 ,IRQ0_IN ,IRQ0_OUT ,NONE ); +MSCC_P (7 ,IRQ1_IN ,IRQ1_OUT ,NONE ); +MSCC_P (8 ,PTP0 ,NONE ,NONE ); +MSCC_P (9 ,PTP1 ,NONE ,NONE ); +MSCC_P (10 ,UART ,NONE ,NONE ); +MSCC_P (11 ,UART ,NONE ,NONE ); +MSCC_P (12 ,SIO1 ,NONE ,NONE ); +MSCC_P (13 ,SIO1 ,NONE ,NONE ); +MSCC_P (14 ,TWI ,TWI_SCL_M ,NONE ); +MSCC_P (15 ,TWI ,NONE ,NONE ); +MSCC_P (16 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (17 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (18 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (19 ,PCI_WAKE ,NONE ,NONE ); +MSCC_P (20 ,IRQ0_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (21 ,IRQ1_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (22 ,TACHO ,NONE ,NONE ); +MSCC_P (23 ,PWM ,NONE ,NONE ); +MSCC_P (24 ,UART2 ,NONE ,NONE ); +MSCC_P (25 ,UART2 ,SI ,NONE ); +MSCC_P (26 ,PTP2 ,SI ,NONE ); +MSCC_P (27 ,PTP3 ,SI ,NONE ); +MSCC_P (28 ,TWI2 ,SI ,NONE ); +MSCC_P (29 ,TWI ,SI ,NONE ); +MSCC_P (30 ,SIO2 ,SI ,NONE ); +MSCC_P (31 ,SIO2 ,SI ,NONE ); +MSCC_P (32 ,SIO2 ,SI ,NONE ); +MSCC_P (33 ,SIO2 ,SI ,NONE ); +MSCC_P (34 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (35 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (36 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (37 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (38 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (39 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (40 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (41 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (42 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (43 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (44 ,NONE ,SFP8 ,NONE ); +MSCC_P (45 ,NONE ,SFP9 ,NONE ); +MSCC_P (46 ,NONE ,SFP10 ,NONE ); +MSCC_P (47 ,NONE ,SFP11 ,NONE ); +MSCC_P (48 ,SFP0 ,NONE ,NONE ); +MSCC_P (49 ,SFP1 ,SI ,NONE ); +MSCC_P (50 ,SFP2 ,SI ,NONE ); +MSCC_P (51 ,SFP3 ,SI ,NONE ); +MSCC_P (52 ,SFP4 ,NONE ,NONE ); +MSCC_P (53 ,SFP5 ,NONE ,NONE ); +MSCC_P (54 ,SFP6 ,NONE ,NONE ); +MSCC_P (55 ,SFP7 ,NONE ,NONE ); +MSCC_P (56 ,MIIM1 ,SFP12 ,NONE ); +MSCC_P (57 ,MIIM1 ,SFP13 ,NONE ); +MSCC_P (58 ,MIIM2 ,SFP14 ,NONE ); +MSCC_P (59 ,MIIM2 ,SFP15 ,NONE ); +MSCC_P (60 ,NONE ,NONE ,NONE ); +MSCC_P (61 ,NONE ,NONE ,NONE ); +MSCC_P (62 ,NONE ,NONE ,NONE ); +MSCC_P (63 ,NONE ,NONE ,NONE ); + +#define JR2_PIN (n) { \ + .name = "GPIO_"#n, \ + .drv_data = &mscc_pin_##n \ +} + +const struct mscc_pin_data jr2_pins[] = { +JR2_PIN (0 ), +JR2_PIN (1 ), +JR2_PIN (2 ), +JR2_PIN (3 ), +JR2_PIN (4 ), +JR2_PIN (5 ), +JR2_PIN (6 ), +JR2_PIN (7 ), +JR2_PIN (8 ), +JR2_PIN (9 ), +JR2_PIN (10 ), +JR2_PIN (11 ), +JR2_PIN (12 ), +JR2_PIN (13 ), +JR2_PIN (14 ), +JR2_PIN (15 ), +JR2_PIN (16 ), +JR2_PIN (17 ), +JR2_PIN (18 ), +JR2_PIN (19 ), +JR2_PIN (20 ), +JR2_PIN (21 ), +JR2_PIN (22 ), +JR2_PIN (23 ), +JR2_PIN (24 ), +JR2_PIN (25 ), +JR2_PIN (26 ), +JR2_PIN (27 ), +JR2_PIN (28 ), +JR2_PIN (29 ), +JR2_PIN (30 ), +JR2_PIN (31 ), +JR2_PIN (32 ), +JR2_PIN (33 ), +JR2_PIN (34 ), +JR2_PIN (35 ), +JR2_PIN (36 ), +JR2_PIN (37 ), +JR2_PIN (38 ), +JR2_PIN (39 ), +JR2_PIN (40 ), +JR2_PIN (41 ), +JR2_PIN (42 ), +JR2_PIN (43 ), +JR2_PIN (44 ), +JR2_PIN (45 ), +JR2_PIN (46 ), +JR2_PIN (47 ), +JR2_PIN (48 ), +JR2_PIN (49 ), +JR2_PIN (50 ), +JR2_PIN (51 ), +JR2_PIN (52 ), +JR2_PIN (53 ), +JR2_PIN (54 ), +JR2_PIN (55 ), +JR2_PIN (56 ), +JR2_PIN (57 ), +JR2_PIN (58 ), +JR2_PIN (59 ), +JR2_PIN (60 ), +JR2_PIN (61 ), +JR2_PIN (62 ), +JR2_PIN (63 ), +}; + +int mscc_pinmux_set_mux (struct udevice *dev, +unsigned int pin_selector,unsigned int selector) +{ +struct mscc_pinctrl *info =dev_get_priv (dev); +struct mscc_pin_caps *pin = info->mscc_pins[pin_selector].drv_data; +int f, offset, regoff; + + f =mscc_pin_function_idx (pin_selector, selector, info->mscc_pins); +if (f <0 ) +return -EINVAL ; +/* +* f is encoded on two bits. +* bit 0 of f goes in BIT(pin) of ALT0, bit 1 of f goes in BIT(pin) of +* ALT1 +* This is racy because both registers can't be updated at the same time +* but it doesn't matter much for now. +*/ + offset = pin->pin; + regoff =MSCC_GPIO_ALT0 ; +if (offset >=32 ) { + offset = offset %32 ; + regoff =MSCC_GPIO_ALT1 ; + } + +if (f &BIT (0 )) +mscc_setbits (offset, info->regs + regoff); +else +mscc_clrbits (offset, info->regs + regoff); + +if (f &BIT (1 )) +mscc_setbits (offset, info->regs + regoff +4 ); +else +mscc_clrbits (offset, info->regs + regoff +4 ); + +return 0 ; +} + +static int jr2_gpio_probe (struct udevice *dev) +{ +struct gpio_dev_priv *uc_priv; + + uc_priv =dev_get_uclass_priv (dev); + uc_priv->bank_name ="jr2-gpio" ; + uc_priv->gpio_count =ARRAY_SIZE (jr2_pins); + +return 0 ; +} + +static struct driver jr2_gpio_driver = { + .name ="jr2-gpio" , + .id =UCLASS_GPIO , + .probe = jr2_gpio_probe, + .ops = &mscc_gpio_ops, +}; + +int jr2_pinctrl_probe (struct udevice *dev) +{ +int ret; + + ret =mscc_pinctrl_probe (dev,FUNC_MAX , jr2_pins, +ARRAY_SIZE (jr2_pins), + jr2_function_names); + +if (ret) +return ret; + + ret =device_bind (dev, &jr2_gpio_driver,"jr2-gpio" ,NULL , +dev_of_offset (dev),NULL ); + +if (ret) +return ret; + +return 0 ; +} + +static const struct udevice_id jr2_pinctrl_of_match[] = { + { .compatible ="mscc,jr2-pinctrl" }, + {}, +}; + +U_BOOT_DRIVER (jr2_pinctrl) = { + .name ="jr2-pinctrl" , + .id =UCLASS_PINCTRL , + .of_match =of_match_ptr (jr2_pinctrl_of_match), + .probe = jr2_pinctrl_probe, + .priv_auto_alloc_size =sizeof (struct mscc_pinctrl ), + .ops = &mscc_pinctrl_ops, +};
Signature · 1 line
- Daniel
PATCH v2 1/7 pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
Hi Daniel,
Quoted 63 lines · Daniel Schwierzeck
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 60 lines
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common to support new numbe of pins.
Signed-off-by Horatiu Vultur <[email protected]>--- MAINTAINERS | 1 + drivers/pinctrl/mscc/Kconfig | 9 + drivers/pinctrl/mscc/Makefile | 1 + drivers/pinctrl/mscc/mscc-common.c | 97 ++++++++--- drivers/pinctrl/mscc/mscc-common.h | 5 + drivers/pinctrl/mscc/pinctrl-jr2.c | 342 +++++++++++++++++++++++++++++++++++++ 6 files changed, 433 insertions(+), 22 deletions(-) create mode 100644 drivers/pinctrl/mscc/pinctrl-jr2.cMAINTAINERS +1
-0@@ -525,6 +525,7 @@ F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c F: include/configs/vcoreiii.h +F: drivers/pinctrl/mscc/ MIPS JZ4780 M: Ezequiel Garcia <[email protected]>drivers/pinctrl/mscc/Kconfig +9
-0@@ -20,3 +20,12 @@ config PINCTRL_MSCC_LUTON help Support pin multiplexing and pin configuration control on Microsemi luton SoCs. + +config PINCTRL_MSCC_JR2 + depends on SOC_JR2 && PINCTRL_FULL && OF_CONTROL + select PINCTRL_MSCC + default y + bool "Microsemi jr2 family pin control driver" + help + Support pin multiplexing and pin configuration control on + Microsemi jr2 SoCs.drivers/pinctrl/mscc/Makefile +1
-0@@ -3,3 +3,4 @@ obj-y += mscc-common.o obj-$(CONFIG_PINCTRL_MSCC_OCELOT) += pinctrl-ocelot.o obj-$(CONFIG_PINCTRL_MSCC_LUTON) += pinctrl-luton.o +obj-$(CONFIG_PINCTRL_MSCC_JR2) += pinctrl-jr2.odrivers/pinctrl/mscc/mscc-common.c +0
-0@@ -22,6 +22,18 @@#include <linux/io.h> #include "mscc-common.h"
Quoted 14 lines
drivers/pinctrl/mscc/mscc-common.c line 36
Quoted 12 lines
drivers/pinctrl/mscc/mscc-common.c +12
-0+#if defined(CONFIG_SOC_JR2 ) +#define MSCC_GPIO_OUT_SET 0x00 +#define MSCC_GPIO_OUT_CLR 0x08 +#define MSCC_GPIO_OUT 0x10 +#define MSCC_GPIO_IN 0x18 +#define MSCC_GPIO_OE 0x20 +#define MSCC_GPIO_INTR 0x28 +#define MSCC_GPIO_INTR_ENA 0x30 +#define MSCC_GPIO_INTR_IDENT 0x38 +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 +#else you should also move this to
pinctrl-jr2.c
If I will move also this in pinctrl-jr2 then I will need to mark many functions as weak and implement them in pinctrl-jr2. And thier implementation will be the same. Another reason why not to move them in pinctr-jr2 is that soon we want to add support for another target which has same features as JR2.
Maybe another solution is to extend the function mscc_pinctrl_probe to receive also an array with the offset of MSCC_GPIO_*. And then each specific pinctrl will need to pass this array, similar with mscc_pins. In this way the mscc-common will not contain any specific code to any of the targets.
Quoted 553 lines
Quoted 171 lines
drivers/pinctrl/mscc/mscc-common.c +62
-21#define MSCC_GPIO_OUT_SET 0x0#define MSCC_GPIO_OUT_CLR 0x4#define MSCC_GPIO_OUT 0x8@@ -32,6 +44,39 @@#define MSCC_GPIO_INTR_IDENT 0x1c#define MSCC_GPIO_ALT0 0x20#define MSCC_GPIO_ALT1 0x24 +#endif + +static void mscc_writel (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (BIT (offset), addr); +else +writel (BIT (offset %32 ), addr +4 ); +} + +static unsigned int mscc_readl (unsigned int offset,void *addr) +{ +if (offset <32 ) +return readl (addr); +else +return readl (addr +4 ); +} + +void mscc_setbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) |BIT (offset), addr); +else +writel (readl (addr +4 ) |BIT (offset %32 ), addr +4 ); +} + +void mscc_clrbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) & ~BIT (offset), addr); +else +writel (readl (addr +4 ) & ~BIT (offset %32 ), addr +4 ); +}static int mscc_get_functions_count (struct udevice *dev) {@@ -48,8 +93,8 @@ static const char *mscc_get_function_name(struct udevice *dev,return info->function_names[function]; } -static int mscc_pin_function_idx (unsigned int pin,unsigned int function, -const struct mscc_pin_data *mscc_pins) +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins) {struct mscc_pin_caps *p = mscc_pins[pin].drv_data;int i;@@ -62,7 +107,7 @@ static int mscc_pin_function_idx(unsigned int pin, unsigned int function,return -1 ; } -static int mscc_pinmux_set_mux (struct udevice *dev, +__weak int mscc_pinmux_set_mux (struct udevice *dev,unsigned int pin_selector,unsigned int selector) {struct mscc_pinctrl *info =dev_get_priv (dev);@@ -79,15 +124,16 @@ static int mscc_pinmux_set_mux(struct udevice *dev,* This is racy because both registers can't be updated at the same time * but it doesn't matter much for now. */ +if (f &BIT (0 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );if (f &BIT (1 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );return 0 ; }@@ -120,8 +166,8 @@ static int mscc_create_group_func_map(struct udevice *dev, } info->func[f].ngroups = npins; - info->func[f].groups =devm_kzalloc (dev, npins * -sizeof (char *),GFP_KERNEL ); + info->func[f].groups =devm_kzalloc (dev, npins *sizeof (char *), +GFP_KERNEL );if (!info->func[f].groups)return -ENOMEM ;@@ -132,7 +178,8 @@ static int mscc_create_group_func_map(struct udevice *dev,return 0 ; } -static int mscc_pinctrl_register (struct udevice *dev,struct mscc_pinctrl *info) +static int mscc_pinctrl_register (struct udevice *dev, +struct mscc_pinctrl *info) {int ret;@@ -150,38 +197,44 @@ static int mscc_gpio_get(struct udevice *dev, unsigned int offset)struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_IN ); +if (mscc_readl (offset, info->regs +MSCC_GPIO_OE ) &BIT (offset %32 )) + val =mscc_readl (offset, info->regs +MSCC_GPIO_OUT ); +else + val =mscc_readl (offset, info->regs +MSCC_GPIO_IN ); -return !!(val &BIT (offset)); +return !!(val &BIT (offset %32 )); } -static int mscc_gpio_set (struct udevice *dev,unsigned int offset,int value) +static int mscc_gpio_set (struct udevice *dev,unsigned int offset, +int value) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);if (value) -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_SET ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_SET );else -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_CLR ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_CLR );return 0 ; } -static int mscc_gpio_get_direction (struct udevice *dev,unsigned int offset) +static int mscc_gpio_get_direction (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_OE ); + val =mscc_readl (offset, info->regs +MSCC_GPIO_OE ); -return (val &BIT (offset)) ?GPIOF_OUTPUT :GPIOF_INPUT ; +return (val &BIT (offset %32 )) ?GPIOF_OUTPUT :GPIOF_INPUT ; } -static int mscc_gpio_direction_input (struct udevice *dev,unsigned int offset) +static int mscc_gpio_direction_input (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -clrbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_clrbits (offset, info->regs +MSCC_GPIO_OE );return 0 ; }@@ -191,7 +244,7 @@ static int mscc_gpio_direction_output(struct udevice *dev, {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -setbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_setbits (offset, info->regs +MSCC_GPIO_OE );return mscc_gpio_set (dev, offset, value); }drivers/pinctrl/mscc/mscc-common.c const struct pinctrl_ops mscc_pinctrl_ops = { · line 271
Quoted 5 lines
drivers/pinctrl/mscc/mscc-common.c +1
-1@@ -215,7 +268,7 @@ const struct pinctrl_ops mscc_pinctrl_ops = {int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins, -char *const *function_names) +char *const *function_names)missing space: char * const
*function_namesQuoted 25 lines
drivers/pinctrl/mscc/mscc-common.c +0
-0{struct mscc_pinctrl *priv =dev_get_priv (dev);int ret;drivers/pinctrl/mscc/mscc-common.h +5
-0@@ -43,6 +43,11 @@ struct mscc_pinctrl {char *const *function_names; }; +void mscc_setbits (unsigned int offset,void *addr); +void mscc_clrbits (unsigned int offset,void *addr); +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins); +int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins,char *const *function_names);drivers/pinctrl/mscc/pinctrl-jr2.c new file +0
-0drivers/pinctrl/mscc/pinctrl-jr2.c line 6
Quoted 6 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +6
-0@@ -0,0 +1,342 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* +* Microsemi SoCs pinctrl driver +* +* Author: <[email protected]> +* License: Dual MIT/GPL license is redundant due to SPDX
Quoted 337 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +336
-0+* Copyright (c) 2018 Microsemi Corporation +*/ + +#include <common.h> +#include <config.h> +#include <dm.h> +#include <dm/device-internal.h> +#include <dm/lists.h> +#include <dm/pinctrl.h> +#include <dm/root.h> +#include <errno.h> +#include <fdtdec.h> +#include <linux/io.h> +#include <asm/gpio.h> +#include <asm/system.h> +#include "mscc-common.h" + +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 + +enum { +FUNC_NONE , +FUNC_GPIO , +FUNC_IRQ0_IN , +FUNC_IRQ0_OUT , +FUNC_IRQ1_IN , +FUNC_IRQ1_OUT , +FUNC_MIIM1 , +FUNC_MIIM2 , +FUNC_PCI_WAKE , +FUNC_PTP0 , +FUNC_PTP1 , +FUNC_PTP2 , +FUNC_PTP3 , +FUNC_PWM , +FUNC_RECO_CLK0 , +FUNC_RECO_CLK1 , +FUNC_SFP0 , +FUNC_SFP1 , +FUNC_SFP2 , +FUNC_SFP3 , +FUNC_SFP4 , +FUNC_SFP5 , +FUNC_SFP6 , +FUNC_SFP7 , +FUNC_SFP8 , +FUNC_SFP9 , +FUNC_SFP10 , +FUNC_SFP11 , +FUNC_SFP12 , +FUNC_SFP13 , +FUNC_SFP14 , +FUNC_SFP15 , +FUNC_SIO , +FUNC_SIO1 , +FUNC_SIO2 , +FUNC_SI , +FUNC_TACHO , +FUNC_TWI , +FUNC_TWI2 , +FUNC_TWI_SCL_M , +FUNC_UART , +FUNC_UART2 , +FUNC_MAX +}; + +char *jr2_function_names[] = { + [FUNC_NONE ] ="none" , + [FUNC_GPIO ] ="gpio" , + [FUNC_IRQ0_IN ] ="irq0_in" , + [FUNC_IRQ0_OUT ] ="irq0_out" , + [FUNC_IRQ1_IN ] ="irq1_in" , + [FUNC_IRQ1_OUT ] ="irq1_out" , + [FUNC_MIIM1 ] ="miim1" , + [FUNC_MIIM2 ] ="miim2" , + [FUNC_PCI_WAKE ] ="pci_wake" , + [FUNC_PTP0 ] ="ptp0" , + [FUNC_PTP1 ] ="ptp1" , + [FUNC_PTP2 ] ="ptp2" , + [FUNC_PTP3 ] ="ptp3" , + [FUNC_PWM ] ="pwm" , + [FUNC_RECO_CLK0 ] ="reco_clk0" , + [FUNC_RECO_CLK1 ] ="reco_clk1" , + [FUNC_SFP0 ] ="sfp0" , + [FUNC_SFP1 ] ="sfp1" , + [FUNC_SFP2 ] ="sfp2" , + [FUNC_SFP3 ] ="sfp3" , + [FUNC_SFP4 ] ="sfp4" , + [FUNC_SFP5 ] ="sfp5" , + [FUNC_SFP6 ] ="sfp6" , + [FUNC_SFP7 ] ="sfp7" , + [FUNC_SFP8 ] ="sfp8" , + [FUNC_SFP9 ] ="sfp9" , + [FUNC_SFP10 ] ="sfp10" , + [FUNC_SFP11 ] ="sfp11" , + [FUNC_SFP12 ] ="sfp12" , + [FUNC_SFP13 ] ="sfp13" , + [FUNC_SFP14 ] ="sfp14" , + [FUNC_SFP15 ] ="sfp15" , + [FUNC_SIO ] ="sio" , + [FUNC_SIO1 ] ="sio1" , + [FUNC_SIO2 ] ="sio2" , + [FUNC_SI ] ="si" , + [FUNC_TACHO ] ="tacho" , + [FUNC_TWI ] ="twi" , + [FUNC_TWI2 ] ="twi2" , + [FUNC_TWI_SCL_M ] ="twi_scl_m" , + [FUNC_UART ] ="uart" , + [FUNC_UART2 ] ="uart2" , +}; + +MSCC_P (0 ,SIO ,NONE ,NONE ); +MSCC_P (1 ,SIO ,NONE ,NONE ); +MSCC_P (2 ,SIO ,NONE ,NONE ); +MSCC_P (3 ,SIO ,NONE ,NONE ); +MSCC_P (4 ,SIO1 ,NONE ,NONE ); +MSCC_P (5 ,SIO1 ,NONE ,NONE ); +MSCC_P (6 ,IRQ0_IN ,IRQ0_OUT ,NONE ); +MSCC_P (7 ,IRQ1_IN ,IRQ1_OUT ,NONE ); +MSCC_P (8 ,PTP0 ,NONE ,NONE ); +MSCC_P (9 ,PTP1 ,NONE ,NONE ); +MSCC_P (10 ,UART ,NONE ,NONE ); +MSCC_P (11 ,UART ,NONE ,NONE ); +MSCC_P (12 ,SIO1 ,NONE ,NONE ); +MSCC_P (13 ,SIO1 ,NONE ,NONE ); +MSCC_P (14 ,TWI ,TWI_SCL_M ,NONE ); +MSCC_P (15 ,TWI ,NONE ,NONE ); +MSCC_P (16 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (17 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (18 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (19 ,PCI_WAKE ,NONE ,NONE ); +MSCC_P (20 ,IRQ0_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (21 ,IRQ1_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (22 ,TACHO ,NONE ,NONE ); +MSCC_P (23 ,PWM ,NONE ,NONE ); +MSCC_P (24 ,UART2 ,NONE ,NONE ); +MSCC_P (25 ,UART2 ,SI ,NONE ); +MSCC_P (26 ,PTP2 ,SI ,NONE ); +MSCC_P (27 ,PTP3 ,SI ,NONE ); +MSCC_P (28 ,TWI2 ,SI ,NONE ); +MSCC_P (29 ,TWI ,SI ,NONE ); +MSCC_P (30 ,SIO2 ,SI ,NONE ); +MSCC_P (31 ,SIO2 ,SI ,NONE ); +MSCC_P (32 ,SIO2 ,SI ,NONE ); +MSCC_P (33 ,SIO2 ,SI ,NONE ); +MSCC_P (34 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (35 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (36 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (37 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (38 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (39 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (40 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (41 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (42 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (43 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (44 ,NONE ,SFP8 ,NONE ); +MSCC_P (45 ,NONE ,SFP9 ,NONE ); +MSCC_P (46 ,NONE ,SFP10 ,NONE ); +MSCC_P (47 ,NONE ,SFP11 ,NONE ); +MSCC_P (48 ,SFP0 ,NONE ,NONE ); +MSCC_P (49 ,SFP1 ,SI ,NONE ); +MSCC_P (50 ,SFP2 ,SI ,NONE ); +MSCC_P (51 ,SFP3 ,SI ,NONE ); +MSCC_P (52 ,SFP4 ,NONE ,NONE ); +MSCC_P (53 ,SFP5 ,NONE ,NONE ); +MSCC_P (54 ,SFP6 ,NONE ,NONE ); +MSCC_P (55 ,SFP7 ,NONE ,NONE ); +MSCC_P (56 ,MIIM1 ,SFP12 ,NONE ); +MSCC_P (57 ,MIIM1 ,SFP13 ,NONE ); +MSCC_P (58 ,MIIM2 ,SFP14 ,NONE ); +MSCC_P (59 ,MIIM2 ,SFP15 ,NONE ); +MSCC_P (60 ,NONE ,NONE ,NONE ); +MSCC_P (61 ,NONE ,NONE ,NONE ); +MSCC_P (62 ,NONE ,NONE ,NONE ); +MSCC_P (63 ,NONE ,NONE ,NONE ); + +#define JR2_PIN (n) { \ + .name = "GPIO_"#n, \ + .drv_data = &mscc_pin_##n \ +} + +const struct mscc_pin_data jr2_pins[] = { +JR2_PIN (0 ), +JR2_PIN (1 ), +JR2_PIN (2 ), +JR2_PIN (3 ), +JR2_PIN (4 ), +JR2_PIN (5 ), +JR2_PIN (6 ), +JR2_PIN (7 ), +JR2_PIN (8 ), +JR2_PIN (9 ), +JR2_PIN (10 ), +JR2_PIN (11 ), +JR2_PIN (12 ), +JR2_PIN (13 ), +JR2_PIN (14 ), +JR2_PIN (15 ), +JR2_PIN (16 ), +JR2_PIN (17 ), +JR2_PIN (18 ), +JR2_PIN (19 ), +JR2_PIN (20 ), +JR2_PIN (21 ), +JR2_PIN (22 ), +JR2_PIN (23 ), +JR2_PIN (24 ), +JR2_PIN (25 ), +JR2_PIN (26 ), +JR2_PIN (27 ), +JR2_PIN (28 ), +JR2_PIN (29 ), +JR2_PIN (30 ), +JR2_PIN (31 ), +JR2_PIN (32 ), +JR2_PIN (33 ), +JR2_PIN (34 ), +JR2_PIN (35 ), +JR2_PIN (36 ), +JR2_PIN (37 ), +JR2_PIN (38 ), +JR2_PIN (39 ), +JR2_PIN (40 ), +JR2_PIN (41 ), +JR2_PIN (42 ), +JR2_PIN (43 ), +JR2_PIN (44 ), +JR2_PIN (45 ), +JR2_PIN (46 ), +JR2_PIN (47 ), +JR2_PIN (48 ), +JR2_PIN (49 ), +JR2_PIN (50 ), +JR2_PIN (51 ), +JR2_PIN (52 ), +JR2_PIN (53 ), +JR2_PIN (54 ), +JR2_PIN (55 ), +JR2_PIN (56 ), +JR2_PIN (57 ), +JR2_PIN (58 ), +JR2_PIN (59 ), +JR2_PIN (60 ), +JR2_PIN (61 ), +JR2_PIN (62 ), +JR2_PIN (63 ), +}; + +int mscc_pinmux_set_mux (struct udevice *dev, +unsigned int pin_selector,unsigned int selector) +{ +struct mscc_pinctrl *info =dev_get_priv (dev); +struct mscc_pin_caps *pin = info->mscc_pins[pin_selector].drv_data; +int f, offset, regoff; + + f =mscc_pin_function_idx (pin_selector, selector, info->mscc_pins); +if (f <0 ) +return -EINVAL ; +/* +* f is encoded on two bits. +* bit 0 of f goes in BIT(pin) of ALT0, bit 1 of f goes in BIT(pin) of +* ALT1 +* This is racy because both registers can't be updated at the same time +* but it doesn't matter much for now. +*/ + offset = pin->pin; + regoff =MSCC_GPIO_ALT0 ; +if (offset >=32 ) { + offset = offset %32 ; + regoff =MSCC_GPIO_ALT1 ; + } + +if (f &BIT (0 )) +mscc_setbits (offset, info->regs + regoff); +else +mscc_clrbits (offset, info->regs + regoff); + +if (f &BIT (1 )) +mscc_setbits (offset, info->regs + regoff +4 ); +else +mscc_clrbits (offset, info->regs + regoff +4 ); + +return 0 ; +} + +static int jr2_gpio_probe (struct udevice *dev) +{ +struct gpio_dev_priv *uc_priv; + + uc_priv =dev_get_uclass_priv (dev); + uc_priv->bank_name ="jr2-gpio" ; + uc_priv->gpio_count =ARRAY_SIZE (jr2_pins); + +return 0 ; +} + +static struct driver jr2_gpio_driver = { + .name ="jr2-gpio" , + .id =UCLASS_GPIO , + .probe = jr2_gpio_probe, + .ops = &mscc_gpio_ops, +}; + +int jr2_pinctrl_probe (struct udevice *dev) +{ +int ret; + + ret =mscc_pinctrl_probe (dev,FUNC_MAX , jr2_pins, +ARRAY_SIZE (jr2_pins), + jr2_function_names); + +if (ret) +return ret; + + ret =device_bind (dev, &jr2_gpio_driver,"jr2-gpio" ,NULL , +dev_of_offset (dev),NULL ); + +if (ret) +return ret; + +return 0 ; +} + +static const struct udevice_id jr2_pinctrl_of_match[] = { + { .compatible ="mscc,jr2-pinctrl" }, + {}, +}; + +U_BOOT_DRIVER (jr2_pinctrl) = { + .name ="jr2-pinctrl" , + .id =UCLASS_PINCTRL , + .of_match =of_match_ptr (jr2_pinctrl_of_match), + .probe = jr2_pinctrl_probe, + .priv_auto_alloc_size =sizeof (struct mscc_pinctrl ), + .ops = &mscc_pinctrl_ops, +};Signature · 1 line
- Daniel
Signature · 1 line
/Horatiu
PATCH v2 1/7 pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
Am 08.01.19 um 09:00 schrieb Horatiu Vultur:
Quoted 87 lines
Hi Daniel,
Quoted 63 lines · Daniel Schwierzeck
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 60 lines
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common to support new numbe of pins.
Signed-off-by Horatiu Vultur <[email protected]>--- MAINTAINERS | 1 + drivers/pinctrl/mscc/Kconfig | 9 + drivers/pinctrl/mscc/Makefile | 1 + drivers/pinctrl/mscc/mscc-common.c | 97 ++++++++--- drivers/pinctrl/mscc/mscc-common.h | 5 + drivers/pinctrl/mscc/pinctrl-jr2.c | 342 +++++++++++++++++++++++++++++++++++++ 6 files changed, 433 insertions(+), 22 deletions(-) create mode 100644 drivers/pinctrl/mscc/pinctrl-jr2.cMAINTAINERS +1
-0@@ -525,6 +525,7 @@ F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c F: include/configs/vcoreiii.h +F: drivers/pinctrl/mscc/ MIPS JZ4780 M: Ezequiel Garcia <[email protected]>drivers/pinctrl/mscc/Kconfig +9
-0@@ -20,3 +20,12 @@ config PINCTRL_MSCC_LUTON help Support pin multiplexing and pin configuration control on Microsemi luton SoCs. + +config PINCTRL_MSCC_JR2 + depends on SOC_JR2 && PINCTRL_FULL && OF_CONTROL + select PINCTRL_MSCC + default y + bool "Microsemi jr2 family pin control driver" + help + Support pin multiplexing and pin configuration control on + Microsemi jr2 SoCs.drivers/pinctrl/mscc/Makefile +1
-0@@ -3,3 +3,4 @@ obj-y += mscc-common.o obj-$(CONFIG_PINCTRL_MSCC_OCELOT) += pinctrl-ocelot.o obj-$(CONFIG_PINCTRL_MSCC_LUTON) += pinctrl-luton.o +obj-$(CONFIG_PINCTRL_MSCC_JR2) += pinctrl-jr2.odrivers/pinctrl/mscc/mscc-common.c +0
-0@@ -22,6 +22,18 @@#include <linux/io.h> #include "mscc-common.h" Quoted 14 lines
drivers/pinctrl/mscc/mscc-common.c line 36
Quoted 12 lines
drivers/pinctrl/mscc/mscc-common.c +12
-0+#if defined(CONFIG_SOC_JR2 ) +#define MSCC_GPIO_OUT_SET 0x00 +#define MSCC_GPIO_OUT_CLR 0x08 +#define MSCC_GPIO_OUT 0x10 +#define MSCC_GPIO_IN 0x18 +#define MSCC_GPIO_OE 0x20 +#define MSCC_GPIO_INTR 0x28 +#define MSCC_GPIO_INTR_ENA 0x30 +#define MSCC_GPIO_INTR_IDENT 0x38 +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 +#else you should also move this to
pinctrl-jr2.cIf I will move also this in pinctrl-jr2 then I will need to mark many functions as weak and implement them in pinctrl-jr2. And thier implementation will be the same. Another reason why not to move them in pinctr-jr2 is that soon we want to add support for another target which has same features as JR2.
Quoted 5 lines
Maybe another solution is to extend the function
mscc_pinctrl_probeto receive also an array with the offset of MSCC_GPIO_*. And then each specific pinctrl will need to pass this array, similar withmscc_pins. In this way the mscc-common will not contain any specific code to any of the targets.
yes, that's even better than __weak. This technique is also used in other drivers where register offset mappings are selected via DT compatible string. One example I know of is drivers/spi/bcm63xx_spi.c.
Quoted 555 lines
Quoted 554 lines
Quoted 172 lines
drivers/pinctrl/mscc/mscc-common.c +62
-21#define MSCC_GPIO_OUT_SET 0x0#define MSCC_GPIO_OUT_CLR 0x4#define MSCC_GPIO_OUT 0x8@@ -32,6 +44,39 @@#define MSCC_GPIO_INTR_IDENT 0x1c#define MSCC_GPIO_ALT0 0x20#define MSCC_GPIO_ALT1 0x24 +#endif + +static void mscc_writel (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (BIT (offset), addr); +else +writel (BIT (offset %32 ), addr +4 ); +} + +static unsigned int mscc_readl (unsigned int offset,void *addr) +{ +if (offset <32 ) +return readl (addr); +else +return readl (addr +4 ); +} + +void mscc_setbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) |BIT (offset), addr); +else +writel (readl (addr +4 ) |BIT (offset %32 ), addr +4 ); +} + +void mscc_clrbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) & ~BIT (offset), addr); +else +writel (readl (addr +4 ) & ~BIT (offset %32 ), addr +4 ); +}static int mscc_get_functions_count (struct udevice *dev) {@@ -48,8 +93,8 @@ static const char *mscc_get_function_name(struct udevice *dev,return info->function_names[function]; } -static int mscc_pin_function_idx (unsigned int pin,unsigned int function, -const struct mscc_pin_data *mscc_pins) +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins) {struct mscc_pin_caps *p = mscc_pins[pin].drv_data;int i;@@ -62,7 +107,7 @@ static int mscc_pin_function_idx(unsigned int pin, unsigned int function,return -1 ; } -static int mscc_pinmux_set_mux (struct udevice *dev, +__weak int mscc_pinmux_set_mux (struct udevice *dev,unsigned int pin_selector,unsigned int selector) {struct mscc_pinctrl *info =dev_get_priv (dev);@@ -79,15 +124,16 @@ static int mscc_pinmux_set_mux(struct udevice *dev,* This is racy because both registers can't be updated at the same time * but it doesn't matter much for now. */ +if (f &BIT (0 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );if (f &BIT (1 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );return 0 ; }@@ -120,8 +166,8 @@ static int mscc_create_group_func_map(struct udevice *dev, } info->func[f].ngroups = npins; - info->func[f].groups =devm_kzalloc (dev, npins * -sizeof (char *),GFP_KERNEL ); + info->func[f].groups =devm_kzalloc (dev, npins *sizeof (char *), +GFP_KERNEL );if (!info->func[f].groups)return -ENOMEM ;@@ -132,7 +178,8 @@ static int mscc_create_group_func_map(struct udevice *dev,return 0 ; } -static int mscc_pinctrl_register (struct udevice *dev,struct mscc_pinctrl *info) +static int mscc_pinctrl_register (struct udevice *dev, +struct mscc_pinctrl *info) {int ret;@@ -150,38 +197,44 @@ static int mscc_gpio_get(struct udevice *dev, unsigned int offset)struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_IN ); +if (mscc_readl (offset, info->regs +MSCC_GPIO_OE ) &BIT (offset %32 )) + val =mscc_readl (offset, info->regs +MSCC_GPIO_OUT ); +else + val =mscc_readl (offset, info->regs +MSCC_GPIO_IN ); -return !!(val &BIT (offset)); +return !!(val &BIT (offset %32 )); } -static int mscc_gpio_set (struct udevice *dev,unsigned int offset,int value) +static int mscc_gpio_set (struct udevice *dev,unsigned int offset, +int value) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);if (value) -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_SET ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_SET );else -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_CLR ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_CLR );return 0 ; } -static int mscc_gpio_get_direction (struct udevice *dev,unsigned int offset) +static int mscc_gpio_get_direction (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_OE ); + val =mscc_readl (offset, info->regs +MSCC_GPIO_OE ); -return (val &BIT (offset)) ?GPIOF_OUTPUT :GPIOF_INPUT ; +return (val &BIT (offset %32 )) ?GPIOF_OUTPUT :GPIOF_INPUT ; } -static int mscc_gpio_direction_input (struct udevice *dev,unsigned int offset) +static int mscc_gpio_direction_input (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -clrbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_clrbits (offset, info->regs +MSCC_GPIO_OE );return 0 ; }@@ -191,7 +244,7 @@ static int mscc_gpio_direction_output(struct udevice *dev, {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -setbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_setbits (offset, info->regs +MSCC_GPIO_OE );return mscc_gpio_set (dev, offset, value); }drivers/pinctrl/mscc/mscc-common.c const struct pinctrl_ops mscc_pinctrl_ops = { · line 271
Quoted 5 lines
drivers/pinctrl/mscc/mscc-common.c +1
-1@@ -215,7 +268,7 @@ const struct pinctrl_ops mscc_pinctrl_ops = {int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins, -char *const *function_names) +char *const *function_names)missing space: char * const
*function_namesQuoted 25 lines
drivers/pinctrl/mscc/mscc-common.c +0
-0{struct mscc_pinctrl *priv =dev_get_priv (dev);int ret;drivers/pinctrl/mscc/mscc-common.h +5
-0@@ -43,6 +43,11 @@ struct mscc_pinctrl {char *const *function_names; }; +void mscc_setbits (unsigned int offset,void *addr); +void mscc_clrbits (unsigned int offset,void *addr); +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins); +int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins,char *const *function_names);drivers/pinctrl/mscc/pinctrl-jr2.c new file +0
-0drivers/pinctrl/mscc/pinctrl-jr2.c line 6
Quoted 6 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +6
-0@@ -0,0 +1,342 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* +* Microsemi SoCs pinctrl driver +* +* Author: <[email protected]> +* License: Dual MIT/GPL license is redundant due to SPDX
Quoted 337 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +336
-0+* Copyright (c) 2018 Microsemi Corporation +*/ + +#include <common.h> +#include <config.h> +#include <dm.h> +#include <dm/device-internal.h> +#include <dm/lists.h> +#include <dm/pinctrl.h> +#include <dm/root.h> +#include <errno.h> +#include <fdtdec.h> +#include <linux/io.h> +#include <asm/gpio.h> +#include <asm/system.h> +#include "mscc-common.h" + +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 + +enum { +FUNC_NONE , +FUNC_GPIO , +FUNC_IRQ0_IN , +FUNC_IRQ0_OUT , +FUNC_IRQ1_IN , +FUNC_IRQ1_OUT , +FUNC_MIIM1 , +FUNC_MIIM2 , +FUNC_PCI_WAKE , +FUNC_PTP0 , +FUNC_PTP1 , +FUNC_PTP2 , +FUNC_PTP3 , +FUNC_PWM , +FUNC_RECO_CLK0 , +FUNC_RECO_CLK1 , +FUNC_SFP0 , +FUNC_SFP1 , +FUNC_SFP2 , +FUNC_SFP3 , +FUNC_SFP4 , +FUNC_SFP5 , +FUNC_SFP6 , +FUNC_SFP7 , +FUNC_SFP8 , +FUNC_SFP9 , +FUNC_SFP10 , +FUNC_SFP11 , +FUNC_SFP12 , +FUNC_SFP13 , +FUNC_SFP14 , +FUNC_SFP15 , +FUNC_SIO , +FUNC_SIO1 , +FUNC_SIO2 , +FUNC_SI , +FUNC_TACHO , +FUNC_TWI , +FUNC_TWI2 , +FUNC_TWI_SCL_M , +FUNC_UART , +FUNC_UART2 , +FUNC_MAX +}; + +char *jr2_function_names[] = { + [FUNC_NONE ] ="none" , + [FUNC_GPIO ] ="gpio" , + [FUNC_IRQ0_IN ] ="irq0_in" , + [FUNC_IRQ0_OUT ] ="irq0_out" , + [FUNC_IRQ1_IN ] ="irq1_in" , + [FUNC_IRQ1_OUT ] ="irq1_out" , + [FUNC_MIIM1 ] ="miim1" , + [FUNC_MIIM2 ] ="miim2" , + [FUNC_PCI_WAKE ] ="pci_wake" , + [FUNC_PTP0 ] ="ptp0" , + [FUNC_PTP1 ] ="ptp1" , + [FUNC_PTP2 ] ="ptp2" , + [FUNC_PTP3 ] ="ptp3" , + [FUNC_PWM ] ="pwm" , + [FUNC_RECO_CLK0 ] ="reco_clk0" , + [FUNC_RECO_CLK1 ] ="reco_clk1" , + [FUNC_SFP0 ] ="sfp0" , + [FUNC_SFP1 ] ="sfp1" , + [FUNC_SFP2 ] ="sfp2" , + [FUNC_SFP3 ] ="sfp3" , + [FUNC_SFP4 ] ="sfp4" , + [FUNC_SFP5 ] ="sfp5" , + [FUNC_SFP6 ] ="sfp6" , + [FUNC_SFP7 ] ="sfp7" , + [FUNC_SFP8 ] ="sfp8" , + [FUNC_SFP9 ] ="sfp9" , + [FUNC_SFP10 ] ="sfp10" , + [FUNC_SFP11 ] ="sfp11" , + [FUNC_SFP12 ] ="sfp12" , + [FUNC_SFP13 ] ="sfp13" , + [FUNC_SFP14 ] ="sfp14" , + [FUNC_SFP15 ] ="sfp15" , + [FUNC_SIO ] ="sio" , + [FUNC_SIO1 ] ="sio1" , + [FUNC_SIO2 ] ="sio2" , + [FUNC_SI ] ="si" , + [FUNC_TACHO ] ="tacho" , + [FUNC_TWI ] ="twi" , + [FUNC_TWI2 ] ="twi2" , + [FUNC_TWI_SCL_M ] ="twi_scl_m" , + [FUNC_UART ] ="uart" , + [FUNC_UART2 ] ="uart2" , +}; + +MSCC_P (0 ,SIO ,NONE ,NONE ); +MSCC_P (1 ,SIO ,NONE ,NONE ); +MSCC_P (2 ,SIO ,NONE ,NONE ); +MSCC_P (3 ,SIO ,NONE ,NONE ); +MSCC_P (4 ,SIO1 ,NONE ,NONE ); +MSCC_P (5 ,SIO1 ,NONE ,NONE ); +MSCC_P (6 ,IRQ0_IN ,IRQ0_OUT ,NONE ); +MSCC_P (7 ,IRQ1_IN ,IRQ1_OUT ,NONE ); +MSCC_P (8 ,PTP0 ,NONE ,NONE ); +MSCC_P (9 ,PTP1 ,NONE ,NONE ); +MSCC_P (10 ,UART ,NONE ,NONE ); +MSCC_P (11 ,UART ,NONE ,NONE ); +MSCC_P (12 ,SIO1 ,NONE ,NONE ); +MSCC_P (13 ,SIO1 ,NONE ,NONE ); +MSCC_P (14 ,TWI ,TWI_SCL_M ,NONE ); +MSCC_P (15 ,TWI ,NONE ,NONE ); +MSCC_P (16 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (17 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (18 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (19 ,PCI_WAKE ,NONE ,NONE ); +MSCC_P (20 ,IRQ0_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (21 ,IRQ1_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (22 ,TACHO ,NONE ,NONE ); +MSCC_P (23 ,PWM ,NONE ,NONE ); +MSCC_P (24 ,UART2 ,NONE ,NONE ); +MSCC_P (25 ,UART2 ,SI ,NONE ); +MSCC_P (26 ,PTP2 ,SI ,NONE ); +MSCC_P (27 ,PTP3 ,SI ,NONE ); +MSCC_P (28 ,TWI2 ,SI ,NONE ); +MSCC_P (29 ,TWI ,SI ,NONE ); +MSCC_P (30 ,SIO2 ,SI ,NONE ); +MSCC_P (31 ,SIO2 ,SI ,NONE ); +MSCC_P (32 ,SIO2 ,SI ,NONE ); +MSCC_P (33 ,SIO2 ,SI ,NONE ); +MSCC_P (34 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (35 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (36 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (37 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (38 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (39 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (40 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (41 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (42 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (43 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (44 ,NONE ,SFP8 ,NONE ); +MSCC_P (45 ,NONE ,SFP9 ,NONE ); +MSCC_P (46 ,NONE ,SFP10 ,NONE ); +MSCC_P (47 ,NONE ,SFP11 ,NONE ); +MSCC_P (48 ,SFP0 ,NONE ,NONE ); +MSCC_P (49 ,SFP1 ,SI ,NONE ); +MSCC_P (50 ,SFP2 ,SI ,NONE ); +MSCC_P (51 ,SFP3 ,SI ,NONE ); +MSCC_P (52 ,SFP4 ,NONE ,NONE ); +MSCC_P (53 ,SFP5 ,NONE ,NONE ); +MSCC_P (54 ,SFP6 ,NONE ,NONE ); +MSCC_P (55 ,SFP7 ,NONE ,NONE ); +MSCC_P (56 ,MIIM1 ,SFP12 ,NONE ); +MSCC_P (57 ,MIIM1 ,SFP13 ,NONE ); +MSCC_P (58 ,MIIM2 ,SFP14 ,NONE ); +MSCC_P (59 ,MIIM2 ,SFP15 ,NONE ); +MSCC_P (60 ,NONE ,NONE ,NONE ); +MSCC_P (61 ,NONE ,NONE ,NONE ); +MSCC_P (62 ,NONE ,NONE ,NONE ); +MSCC_P (63 ,NONE ,NONE ,NONE ); + +#define JR2_PIN (n) { \ + .name = "GPIO_"#n, \ + .drv_data = &mscc_pin_##n \ +} + +const struct mscc_pin_data jr2_pins[] = { +JR2_PIN (0 ), +JR2_PIN (1 ), +JR2_PIN (2 ), +JR2_PIN (3 ), +JR2_PIN (4 ), +JR2_PIN (5 ), +JR2_PIN (6 ), +JR2_PIN (7 ), +JR2_PIN (8 ), +JR2_PIN (9 ), +JR2_PIN (10 ), +JR2_PIN (11 ), +JR2_PIN (12 ), +JR2_PIN (13 ), +JR2_PIN (14 ), +JR2_PIN (15 ), +JR2_PIN (16 ), +JR2_PIN (17 ), +JR2_PIN (18 ), +JR2_PIN (19 ), +JR2_PIN (20 ), +JR2_PIN (21 ), +JR2_PIN (22 ), +JR2_PIN (23 ), +JR2_PIN (24 ), +JR2_PIN (25 ), +JR2_PIN (26 ), +JR2_PIN (27 ), +JR2_PIN (28 ), +JR2_PIN (29 ), +JR2_PIN (30 ), +JR2_PIN (31 ), +JR2_PIN (32 ), +JR2_PIN (33 ), +JR2_PIN (34 ), +JR2_PIN (35 ), +JR2_PIN (36 ), +JR2_PIN (37 ), +JR2_PIN (38 ), +JR2_PIN (39 ), +JR2_PIN (40 ), +JR2_PIN (41 ), +JR2_PIN (42 ), +JR2_PIN (43 ), +JR2_PIN (44 ), +JR2_PIN (45 ), +JR2_PIN (46 ), +JR2_PIN (47 ), +JR2_PIN (48 ), +JR2_PIN (49 ), +JR2_PIN (50 ), +JR2_PIN (51 ), +JR2_PIN (52 ), +JR2_PIN (53 ), +JR2_PIN (54 ), +JR2_PIN (55 ), +JR2_PIN (56 ), +JR2_PIN (57 ), +JR2_PIN (58 ), +JR2_PIN (59 ), +JR2_PIN (60 ), +JR2_PIN (61 ), +JR2_PIN (62 ), +JR2_PIN (63 ), +}; + +int mscc_pinmux_set_mux (struct udevice *dev, +unsigned int pin_selector,unsigned int selector) +{ +struct mscc_pinctrl *info =dev_get_priv (dev); +struct mscc_pin_caps *pin = info->mscc_pins[pin_selector].drv_data; +int f, offset, regoff; + + f =mscc_pin_function_idx (pin_selector, selector, info->mscc_pins); +if (f <0 ) +return -EINVAL ; +/* +* f is encoded on two bits. +* bit 0 of f goes in BIT(pin) of ALT0, bit 1 of f goes in BIT(pin) of +* ALT1 +* This is racy because both registers can't be updated at the same time +* but it doesn't matter much for now. +*/ + offset = pin->pin; + regoff =MSCC_GPIO_ALT0 ; +if (offset >=32 ) { + offset = offset %32 ; + regoff =MSCC_GPIO_ALT1 ; + } + +if (f &BIT (0 )) +mscc_setbits (offset, info->regs + regoff); +else +mscc_clrbits (offset, info->regs + regoff); + +if (f &BIT (1 )) +mscc_setbits (offset, info->regs + regoff +4 ); +else +mscc_clrbits (offset, info->regs + regoff +4 ); + +return 0 ; +} + +static int jr2_gpio_probe (struct udevice *dev) +{ +struct gpio_dev_priv *uc_priv; + + uc_priv =dev_get_uclass_priv (dev); + uc_priv->bank_name ="jr2-gpio" ; + uc_priv->gpio_count =ARRAY_SIZE (jr2_pins); + +return 0 ; +} + +static struct driver jr2_gpio_driver = { + .name ="jr2-gpio" , + .id =UCLASS_GPIO , + .probe = jr2_gpio_probe, + .ops = &mscc_gpio_ops, +}; + +int jr2_pinctrl_probe (struct udevice *dev) +{ +int ret; + + ret =mscc_pinctrl_probe (dev,FUNC_MAX , jr2_pins, +ARRAY_SIZE (jr2_pins), + jr2_function_names); + +if (ret) +return ret; + + ret =device_bind (dev, &jr2_gpio_driver,"jr2-gpio" ,NULL , +dev_of_offset (dev),NULL ); + +if (ret) +return ret; + +return 0 ; +} + +static const struct udevice_id jr2_pinctrl_of_match[] = { + { .compatible ="mscc,jr2-pinctrl" }, + {}, +}; + +U_BOOT_DRIVER (jr2_pinctrl) = { + .name ="jr2-pinctrl" , + .id =UCLASS_PINCTRL , + .of_match =of_match_ptr (jr2_pinctrl_of_match), + .probe = jr2_pinctrl_probe, + .priv_auto_alloc_size =sizeof (struct mscc_pinctrl ), + .ops = &mscc_pinctrl_ops, +};Signature · 1 line
- Daniel
Signature · 1 line
- Daniel
PATCH v2 1/7 pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
Hi Daniel,
First, thank you for all the feedback.
I have created a new patch series that will fix the issue that you addressed bellow but the fix it would not use compatible string, because that presume that I need to change the other pinctrl-drivers(ocelot, luton). I was thinking if it is OK the way I have done in v3 and then create a new patch series specific for fixing pinctrl. Similar with the issue that I have for sysreset driver.
Quoted 658 lines · Daniel Schwierzeck
Am 08.01.19 um 09:00 schrieb Horatiu Vultur:
Quoted 87 lines
Hi Daniel,
Quoted 63 lines · Daniel Schwierzeck
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 60 lines
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common to support new numbe of pins.
Signed-off-by Horatiu Vultur <[email protected]>--- MAINTAINERS | 1 + drivers/pinctrl/mscc/Kconfig | 9 + drivers/pinctrl/mscc/Makefile | 1 + drivers/pinctrl/mscc/mscc-common.c | 97 ++++++++--- drivers/pinctrl/mscc/mscc-common.h | 5 + drivers/pinctrl/mscc/pinctrl-jr2.c | 342 +++++++++++++++++++++++++++++++++++++ 6 files changed, 433 insertions(+), 22 deletions(-) create mode 100644 drivers/pinctrl/mscc/pinctrl-jr2.cMAINTAINERS +1
-0@@ -525,6 +525,7 @@ F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c F: include/configs/vcoreiii.h +F: drivers/pinctrl/mscc/ MIPS JZ4780 M: Ezequiel Garcia <[email protected]>drivers/pinctrl/mscc/Kconfig +9
-0@@ -20,3 +20,12 @@ config PINCTRL_MSCC_LUTON help Support pin multiplexing and pin configuration control on Microsemi luton SoCs. + +config PINCTRL_MSCC_JR2 + depends on SOC_JR2 && PINCTRL_FULL && OF_CONTROL + select PINCTRL_MSCC + default y + bool "Microsemi jr2 family pin control driver" + help + Support pin multiplexing and pin configuration control on + Microsemi jr2 SoCs.drivers/pinctrl/mscc/Makefile +1
-0@@ -3,3 +3,4 @@ obj-y += mscc-common.o obj-$(CONFIG_PINCTRL_MSCC_OCELOT) += pinctrl-ocelot.o obj-$(CONFIG_PINCTRL_MSCC_LUTON) += pinctrl-luton.o +obj-$(CONFIG_PINCTRL_MSCC_JR2) += pinctrl-jr2.odrivers/pinctrl/mscc/mscc-common.c +0
-0@@ -22,6 +22,18 @@#include <linux/io.h> #include "mscc-common.h" Quoted 14 lines
drivers/pinctrl/mscc/mscc-common.c line 36
Quoted 12 lines
drivers/pinctrl/mscc/mscc-common.c +12
-0+#if defined(CONFIG_SOC_JR2 ) +#define MSCC_GPIO_OUT_SET 0x00 +#define MSCC_GPIO_OUT_CLR 0x08 +#define MSCC_GPIO_OUT 0x10 +#define MSCC_GPIO_IN 0x18 +#define MSCC_GPIO_OE 0x20 +#define MSCC_GPIO_INTR 0x28 +#define MSCC_GPIO_INTR_ENA 0x30 +#define MSCC_GPIO_INTR_IDENT 0x38 +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 +#else you should also move this to
pinctrl-jr2.cIf I will move also this in pinctrl-jr2 then I will need to mark many functions as weak and implement them in pinctrl-jr2. And thier implementation will be the same. Another reason why not to move them in pinctr-jr2 is that soon we want to add support for another target which has same features as JR2.
Quoted 5 lines
Maybe another solution is to extend the function
mscc_pinctrl_probeto receive also an array with the offset of MSCC_GPIO_*. And then each specific pinctrl will need to pass this array, similar withmscc_pins. In this way the mscc-common will not contain any specific code to any of the targets.yes, that's even better than
__weak. This technique is also used in other drivers where register offset mappings are selected via DT compatible string. One example I know of isdrivers/spi/bcm63xx_spi.c.Quoted 555 lines
Quoted 554 lines
Quoted 172 lines
drivers/pinctrl/mscc/mscc-common.c +62
-21#define MSCC_GPIO_OUT_SET 0x0#define MSCC_GPIO_OUT_CLR 0x4#define MSCC_GPIO_OUT 0x8@@ -32,6 +44,39 @@#define MSCC_GPIO_INTR_IDENT 0x1c#define MSCC_GPIO_ALT0 0x20#define MSCC_GPIO_ALT1 0x24 +#endif + +static void mscc_writel (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (BIT (offset), addr); +else +writel (BIT (offset %32 ), addr +4 ); +} + +static unsigned int mscc_readl (unsigned int offset,void *addr) +{ +if (offset <32 ) +return readl (addr); +else +return readl (addr +4 ); +} + +void mscc_setbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) |BIT (offset), addr); +else +writel (readl (addr +4 ) |BIT (offset %32 ), addr +4 ); +} + +void mscc_clrbits (unsigned int offset,void *addr) +{ +if (offset <32 ) +writel (readl (addr) & ~BIT (offset), addr); +else +writel (readl (addr +4 ) & ~BIT (offset %32 ), addr +4 ); +}static int mscc_get_functions_count (struct udevice *dev) {@@ -48,8 +93,8 @@ static const char *mscc_get_function_name(struct udevice *dev,return info->function_names[function]; } -static int mscc_pin_function_idx (unsigned int pin,unsigned int function, -const struct mscc_pin_data *mscc_pins) +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins) {struct mscc_pin_caps *p = mscc_pins[pin].drv_data;int i;@@ -62,7 +107,7 @@ static int mscc_pin_function_idx(unsigned int pin, unsigned int function,return -1 ; } -static int mscc_pinmux_set_mux (struct udevice *dev, +__weak int mscc_pinmux_set_mux (struct udevice *dev,unsigned int pin_selector,unsigned int selector) {struct mscc_pinctrl *info =dev_get_priv (dev);@@ -79,15 +124,16 @@ static int mscc_pinmux_set_mux(struct udevice *dev,* This is racy because both registers can't be updated at the same time * but it doesn't matter much for now. */ +if (f &BIT (0 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT0 ,BIT (pin->pin)); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT0 );if (f &BIT (1 )) -setbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_setbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );else -clrbits_le32 (info->regs +MSCC_GPIO_ALT1 ,BIT (pin->pin -1 )); +mscc_clrbits (pin->pin, info->regs +MSCC_GPIO_ALT1 +4 );return 0 ; }@@ -120,8 +166,8 @@ static int mscc_create_group_func_map(struct udevice *dev, } info->func[f].ngroups = npins; - info->func[f].groups =devm_kzalloc (dev, npins * -sizeof (char *),GFP_KERNEL ); + info->func[f].groups =devm_kzalloc (dev, npins *sizeof (char *), +GFP_KERNEL );if (!info->func[f].groups)return -ENOMEM ;@@ -132,7 +178,8 @@ static int mscc_create_group_func_map(struct udevice *dev,return 0 ; } -static int mscc_pinctrl_register (struct udevice *dev,struct mscc_pinctrl *info) +static int mscc_pinctrl_register (struct udevice *dev, +struct mscc_pinctrl *info) {int ret;@@ -150,38 +197,44 @@ static int mscc_gpio_get(struct udevice *dev, unsigned int offset)struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_IN ); +if (mscc_readl (offset, info->regs +MSCC_GPIO_OE ) &BIT (offset %32 )) + val =mscc_readl (offset, info->regs +MSCC_GPIO_OUT ); +else + val =mscc_readl (offset, info->regs +MSCC_GPIO_IN ); -return !!(val &BIT (offset)); +return !!(val &BIT (offset %32 )); } -static int mscc_gpio_set (struct udevice *dev,unsigned int offset,int value) +static int mscc_gpio_set (struct udevice *dev,unsigned int offset, +int value) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);if (value) -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_SET ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_SET );else -writel (BIT (offset), info->regs +MSCC_GPIO_OUT_CLR ); +mscc_writel (offset, info->regs +MSCC_GPIO_OUT_CLR );return 0 ; } -static int mscc_gpio_get_direction (struct udevice *dev,unsigned int offset) +static int mscc_gpio_get_direction (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent);unsigned int val; - val =readl (info->regs +MSCC_GPIO_OE ); + val =mscc_readl (offset, info->regs +MSCC_GPIO_OE ); -return (val &BIT (offset)) ?GPIOF_OUTPUT :GPIOF_INPUT ; +return (val &BIT (offset %32 )) ?GPIOF_OUTPUT :GPIOF_INPUT ; } -static int mscc_gpio_direction_input (struct udevice *dev,unsigned int offset) +static int mscc_gpio_direction_input (struct udevice *dev, +unsigned int offset) {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -clrbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_clrbits (offset, info->regs +MSCC_GPIO_OE );return 0 ; }@@ -191,7 +244,7 @@ static int mscc_gpio_direction_output(struct udevice *dev, {struct mscc_pinctrl *info =dev_get_priv (dev->parent); -setbits_le32 (info->regs +MSCC_GPIO_OE ,BIT (offset)); +mscc_setbits (offset, info->regs +MSCC_GPIO_OE );return mscc_gpio_set (dev, offset, value); }drivers/pinctrl/mscc/mscc-common.c const struct pinctrl_ops mscc_pinctrl_ops = { · line 271
Quoted 5 lines
drivers/pinctrl/mscc/mscc-common.c +1
-1@@ -215,7 +268,7 @@ const struct pinctrl_ops mscc_pinctrl_ops = {int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins, -char *const *function_names) +char *const *function_names)missing space: char * const
*function_namesQuoted 25 lines
drivers/pinctrl/mscc/mscc-common.c +0
-0{struct mscc_pinctrl *priv =dev_get_priv (dev);int ret;drivers/pinctrl/mscc/mscc-common.h +5
-0@@ -43,6 +43,11 @@ struct mscc_pinctrl {char *const *function_names; }; +void mscc_setbits (unsigned int offset,void *addr); +void mscc_clrbits (unsigned int offset,void *addr); +int mscc_pin_function_idx (unsigned int pin,unsigned int function, +const struct mscc_pin_data *mscc_pins); +int mscc_pinctrl_probe (struct udevice *dev,int num_func,const struct mscc_pin_data *mscc_pins,int num_pins,char *const *function_names);drivers/pinctrl/mscc/pinctrl-jr2.c new file +0
-0drivers/pinctrl/mscc/pinctrl-jr2.c line 6
Quoted 6 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +6
-0@@ -0,0 +1,342 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* +* Microsemi SoCs pinctrl driver +* +* Author: <[email protected]> +* License: Dual MIT/GPL license is redundant due to SPDX
Quoted 337 lines
drivers/pinctrl/mscc/pinctrl-jr2.c new file +336
-0+* Copyright (c) 2018 Microsemi Corporation +*/ + +#include <common.h> +#include <config.h> +#include <dm.h> +#include <dm/device-internal.h> +#include <dm/lists.h> +#include <dm/pinctrl.h> +#include <dm/root.h> +#include <errno.h> +#include <fdtdec.h> +#include <linux/io.h> +#include <asm/gpio.h> +#include <asm/system.h> +#include "mscc-common.h" + +#define MSCC_GPIO_ALT0 0x40 +#define MSCC_GPIO_ALT1 0x48 + +enum { +FUNC_NONE , +FUNC_GPIO , +FUNC_IRQ0_IN , +FUNC_IRQ0_OUT , +FUNC_IRQ1_IN , +FUNC_IRQ1_OUT , +FUNC_MIIM1 , +FUNC_MIIM2 , +FUNC_PCI_WAKE , +FUNC_PTP0 , +FUNC_PTP1 , +FUNC_PTP2 , +FUNC_PTP3 , +FUNC_PWM , +FUNC_RECO_CLK0 , +FUNC_RECO_CLK1 , +FUNC_SFP0 , +FUNC_SFP1 , +FUNC_SFP2 , +FUNC_SFP3 , +FUNC_SFP4 , +FUNC_SFP5 , +FUNC_SFP6 , +FUNC_SFP7 , +FUNC_SFP8 , +FUNC_SFP9 , +FUNC_SFP10 , +FUNC_SFP11 , +FUNC_SFP12 , +FUNC_SFP13 , +FUNC_SFP14 , +FUNC_SFP15 , +FUNC_SIO , +FUNC_SIO1 , +FUNC_SIO2 , +FUNC_SI , +FUNC_TACHO , +FUNC_TWI , +FUNC_TWI2 , +FUNC_TWI_SCL_M , +FUNC_UART , +FUNC_UART2 , +FUNC_MAX +}; + +char *jr2_function_names[] = { + [FUNC_NONE ] ="none" , + [FUNC_GPIO ] ="gpio" , + [FUNC_IRQ0_IN ] ="irq0_in" , + [FUNC_IRQ0_OUT ] ="irq0_out" , + [FUNC_IRQ1_IN ] ="irq1_in" , + [FUNC_IRQ1_OUT ] ="irq1_out" , + [FUNC_MIIM1 ] ="miim1" , + [FUNC_MIIM2 ] ="miim2" , + [FUNC_PCI_WAKE ] ="pci_wake" , + [FUNC_PTP0 ] ="ptp0" , + [FUNC_PTP1 ] ="ptp1" , + [FUNC_PTP2 ] ="ptp2" , + [FUNC_PTP3 ] ="ptp3" , + [FUNC_PWM ] ="pwm" , + [FUNC_RECO_CLK0 ] ="reco_clk0" , + [FUNC_RECO_CLK1 ] ="reco_clk1" , + [FUNC_SFP0 ] ="sfp0" , + [FUNC_SFP1 ] ="sfp1" , + [FUNC_SFP2 ] ="sfp2" , + [FUNC_SFP3 ] ="sfp3" , + [FUNC_SFP4 ] ="sfp4" , + [FUNC_SFP5 ] ="sfp5" , + [FUNC_SFP6 ] ="sfp6" , + [FUNC_SFP7 ] ="sfp7" , + [FUNC_SFP8 ] ="sfp8" , + [FUNC_SFP9 ] ="sfp9" , + [FUNC_SFP10 ] ="sfp10" , + [FUNC_SFP11 ] ="sfp11" , + [FUNC_SFP12 ] ="sfp12" , + [FUNC_SFP13 ] ="sfp13" , + [FUNC_SFP14 ] ="sfp14" , + [FUNC_SFP15 ] ="sfp15" , + [FUNC_SIO ] ="sio" , + [FUNC_SIO1 ] ="sio1" , + [FUNC_SIO2 ] ="sio2" , + [FUNC_SI ] ="si" , + [FUNC_TACHO ] ="tacho" , + [FUNC_TWI ] ="twi" , + [FUNC_TWI2 ] ="twi2" , + [FUNC_TWI_SCL_M ] ="twi_scl_m" , + [FUNC_UART ] ="uart" , + [FUNC_UART2 ] ="uart2" , +}; + +MSCC_P (0 ,SIO ,NONE ,NONE ); +MSCC_P (1 ,SIO ,NONE ,NONE ); +MSCC_P (2 ,SIO ,NONE ,NONE ); +MSCC_P (3 ,SIO ,NONE ,NONE ); +MSCC_P (4 ,SIO1 ,NONE ,NONE ); +MSCC_P (5 ,SIO1 ,NONE ,NONE ); +MSCC_P (6 ,IRQ0_IN ,IRQ0_OUT ,NONE ); +MSCC_P (7 ,IRQ1_IN ,IRQ1_OUT ,NONE ); +MSCC_P (8 ,PTP0 ,NONE ,NONE ); +MSCC_P (9 ,PTP1 ,NONE ,NONE ); +MSCC_P (10 ,UART ,NONE ,NONE ); +MSCC_P (11 ,UART ,NONE ,NONE ); +MSCC_P (12 ,SIO1 ,NONE ,NONE ); +MSCC_P (13 ,SIO1 ,NONE ,NONE ); +MSCC_P (14 ,TWI ,TWI_SCL_M ,NONE ); +MSCC_P (15 ,TWI ,NONE ,NONE ); +MSCC_P (16 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (17 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (18 ,SI ,TWI_SCL_M ,NONE ); +MSCC_P (19 ,PCI_WAKE ,NONE ,NONE ); +MSCC_P (20 ,IRQ0_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (21 ,IRQ1_OUT ,TWI_SCL_M ,NONE ); +MSCC_P (22 ,TACHO ,NONE ,NONE ); +MSCC_P (23 ,PWM ,NONE ,NONE ); +MSCC_P (24 ,UART2 ,NONE ,NONE ); +MSCC_P (25 ,UART2 ,SI ,NONE ); +MSCC_P (26 ,PTP2 ,SI ,NONE ); +MSCC_P (27 ,PTP3 ,SI ,NONE ); +MSCC_P (28 ,TWI2 ,SI ,NONE ); +MSCC_P (29 ,TWI ,SI ,NONE ); +MSCC_P (30 ,SIO2 ,SI ,NONE ); +MSCC_P (31 ,SIO2 ,SI ,NONE ); +MSCC_P (32 ,SIO2 ,SI ,NONE ); +MSCC_P (33 ,SIO2 ,SI ,NONE ); +MSCC_P (34 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (35 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (36 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (37 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (38 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (39 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (40 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (41 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (42 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (43 ,NONE ,TWI_SCL_M ,NONE ); +MSCC_P (44 ,NONE ,SFP8 ,NONE ); +MSCC_P (45 ,NONE ,SFP9 ,NONE ); +MSCC_P (46 ,NONE ,SFP10 ,NONE ); +MSCC_P (47 ,NONE ,SFP11 ,NONE ); +MSCC_P (48 ,SFP0 ,NONE ,NONE ); +MSCC_P (49 ,SFP1 ,SI ,NONE ); +MSCC_P (50 ,SFP2 ,SI ,NONE ); +MSCC_P (51 ,SFP3 ,SI ,NONE ); +MSCC_P (52 ,SFP4 ,NONE ,NONE ); +MSCC_P (53 ,SFP5 ,NONE ,NONE ); +MSCC_P (54 ,SFP6 ,NONE ,NONE ); +MSCC_P (55 ,SFP7 ,NONE ,NONE ); +MSCC_P (56 ,MIIM1 ,SFP12 ,NONE ); +MSCC_P (57 ,MIIM1 ,SFP13 ,NONE ); +MSCC_P (58 ,MIIM2 ,SFP14 ,NONE ); +MSCC_P (59 ,MIIM2 ,SFP15 ,NONE ); +MSCC_P (60 ,NONE ,NONE ,NONE ); +MSCC_P (61 ,NONE ,NONE ,NONE ); +MSCC_P (62 ,NONE ,NONE ,NONE ); +MSCC_P (63 ,NONE ,NONE ,NONE ); + +#define JR2_PIN (n) { \ + .name = "GPIO_"#n, \ + .drv_data = &mscc_pin_##n \ +} + +const struct mscc_pin_data jr2_pins[] = { +JR2_PIN (0 ), +JR2_PIN (1 ), +JR2_PIN (2 ), +JR2_PIN (3 ), +JR2_PIN (4 ), +JR2_PIN (5 ), +JR2_PIN (6 ), +JR2_PIN (7 ), +JR2_PIN (8 ), +JR2_PIN (9 ), +JR2_PIN (10 ), +JR2_PIN (11 ), +JR2_PIN (12 ), +JR2_PIN (13 ), +JR2_PIN (14 ), +JR2_PIN (15 ), +JR2_PIN (16 ), +JR2_PIN (17 ), +JR2_PIN (18 ), +JR2_PIN (19 ), +JR2_PIN (20 ), +JR2_PIN (21 ), +JR2_PIN (22 ), +JR2_PIN (23 ), +JR2_PIN (24 ), +JR2_PIN (25 ), +JR2_PIN (26 ), +JR2_PIN (27 ), +JR2_PIN (28 ), +JR2_PIN (29 ), +JR2_PIN (30 ), +JR2_PIN (31 ), +JR2_PIN (32 ), +JR2_PIN (33 ), +JR2_PIN (34 ), +JR2_PIN (35 ), +JR2_PIN (36 ), +JR2_PIN (37 ), +JR2_PIN (38 ), +JR2_PIN (39 ), +JR2_PIN (40 ), +JR2_PIN (41 ), +JR2_PIN (42 ), +JR2_PIN (43 ), +JR2_PIN (44 ), +JR2_PIN (45 ), +JR2_PIN (46 ), +JR2_PIN (47 ), +JR2_PIN (48 ), +JR2_PIN (49 ), +JR2_PIN (50 ), +JR2_PIN (51 ), +JR2_PIN (52 ), +JR2_PIN (53 ), +JR2_PIN (54 ), +JR2_PIN (55 ), +JR2_PIN (56 ), +JR2_PIN (57 ), +JR2_PIN (58 ), +JR2_PIN (59 ), +JR2_PIN (60 ), +JR2_PIN (61 ), +JR2_PIN (62 ), +JR2_PIN (63 ), +}; + +int mscc_pinmux_set_mux (struct udevice *dev, +unsigned int pin_selector,unsigned int selector) +{ +struct mscc_pinctrl *info =dev_get_priv (dev); +struct mscc_pin_caps *pin = info->mscc_pins[pin_selector].drv_data; +int f, offset, regoff; + + f =mscc_pin_function_idx (pin_selector, selector, info->mscc_pins); +if (f <0 ) +return -EINVAL ; +/* +* f is encoded on two bits. +* bit 0 of f goes in BIT(pin) of ALT0, bit 1 of f goes in BIT(pin) of +* ALT1 +* This is racy because both registers can't be updated at the same time +* but it doesn't matter much for now. +*/ + offset = pin->pin; + regoff =MSCC_GPIO_ALT0 ; +if (offset >=32 ) { + offset = offset %32 ; + regoff =MSCC_GPIO_ALT1 ; + } + +if (f &BIT (0 )) +mscc_setbits (offset, info->regs + regoff); +else +mscc_clrbits (offset, info->regs + regoff); + +if (f &BIT (1 )) +mscc_setbits (offset, info->regs + regoff +4 ); +else +mscc_clrbits (offset, info->regs + regoff +4 ); + +return 0 ; +} + +static int jr2_gpio_probe (struct udevice *dev) +{ +struct gpio_dev_priv *uc_priv; + + uc_priv =dev_get_uclass_priv (dev); + uc_priv->bank_name ="jr2-gpio" ; + uc_priv->gpio_count =ARRAY_SIZE (jr2_pins); + +return 0 ; +} + +static struct driver jr2_gpio_driver = { + .name ="jr2-gpio" , + .id =UCLASS_GPIO , + .probe = jr2_gpio_probe, + .ops = &mscc_gpio_ops, +}; + +int jr2_pinctrl_probe (struct udevice *dev) +{ +int ret; + + ret =mscc_pinctrl_probe (dev,FUNC_MAX , jr2_pins, +ARRAY_SIZE (jr2_pins), + jr2_function_names); + +if (ret) +return ret; + + ret =device_bind (dev, &jr2_gpio_driver,"jr2-gpio" ,NULL , +dev_of_offset (dev),NULL ); + +if (ret) +return ret; + +return 0 ; +} + +static const struct udevice_id jr2_pinctrl_of_match[] = { + { .compatible ="mscc,jr2-pinctrl" }, + {}, +}; + +U_BOOT_DRIVER (jr2_pinctrl) = { + .name ="jr2-pinctrl" , + .id =UCLASS_PINCTRL , + .of_match =of_match_ptr (jr2_pinctrl_of_match), + .probe = jr2_pinctrl_probe, + .priv_auto_alloc_size =sizeof (struct mscc_pinctrl ), + .ops = &mscc_pinctrl_ops, +};Signature · 1 line
- DanielSignature · 1 line
- Daniel
Signature · 1 line
/Horatiu
PATCH v2 1/7 pinctrl: mscc: Add gpio and pinctrl for Jaguar2 SOC family
Am 09.01.19 um 09:21 schrieb Horatiu Vultur:
Quoted 10 lines
Hi Daniel,
First, thank you for all the feedback.
I have created a new patch series that will fix the issue that you addressed bellow but the fix it would not use compatible string, because that presume that I need to change the other pinctrl-drivers(ocelot, luton). I was thinking if it is OK the way I have done in v3 and then create a new patch series specific for fixing pinctrl. Similar with the issue that I have for sysreset driver.
I didn't expect that you select the registers via compatible strings in the pinctrl driver because you effectively have three drivers and a common driver core. Your v3 variant is perfect. The compatible string method makes sense for drivers that support more than one SoC. The sysreset driver could be an example.
Signature · 1 line
- Daniel
PATCH v2 2/7 MSCC: Add support for Jaguar2 SOC family
In reply to Horatiu VulturAs the Ocelot and Luton SoCs, this family of SoCs are found in Microsemi Switches solution.
--- arch/mips/mach-mscc/Kconfig | 9 + arch/mips/mach-mscc/cpu.c | 7 + arch/mips/mach-mscc/dram.c | 2 +- arch/mips/mach-mscc/include/mach/common.h | 5 + arch/mips/mach-mscc/include/mach/ddr.h | 38 ++- arch/mips/mach-mscc/include/mach/jr2/jr2.h | 24 ++ .../mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h | 20 ++ .../include/mach/jr2/jr2_devcpu_gcb_miim_regs.h | 25 ++ .../mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h | 321 +++++++++++++++++++++ 9 files changed, 443 insertions(+), 8 deletions(-) create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb_miim_regs.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h
arch/mips/mach-mscc/Kconfig +9 -0
@@ -33,6 +33,13 @@ config SOC_LUTON help This supports MSCC Luton family of SOCs. +config SOC_JR2 + bool "Jaguar2 SOC Family" + select SOC_VCOREIII + select DESIGNWARE_SPI + help + This supports MSCC Jaguar2 family of SOCs. + endchoice config SYS_CONFIG_NAME
@@ -65,4 +72,6 @@ source "board/mscc/ocelot/Kconfig" source "board/mscc/luton/Kconfig" +source "board/mscc/jr2/Kconfig" + endmenu
arch/mips/mach-mscc/cpu.c +7 -0
@@ -87,8 +87,15 @@ int mach_cpu_init(void)ICPU_SPI_MST_CFG_CS_DESELECT_TIME (0x19 ) + ICPU_SPI_MST_CFG_CLK_DIV(9), BASE_CFG + ICPU_SPI_MST_CFG);#else +#ifdef CONFIG_SOC_OCELOT writel (ICPU_SPI_MST_CFG_CS_DESELECT_TIME (0x19 ) +ICPU_SPI_MST_CFG_CLK_DIV (9 ),BASE_CFG +ICPU_SPI_MST_CFG ); +#endif +#ifdef CONFIG_SOC_JR2 +writel (ICPU_SPI_MST_CFG_FAST_READ_ENA + +ICPU_SPI_MST_CFG_CS_DESELECT_TIME (0x19 ) + +ICPU_SPI_MST_CFG_CLK_DIV (14 ),BASE_CFG +ICPU_SPI_MST_CFG ); +#endif /* * Legacy and mainline linux kernel expect that the * interruption map was set as it was done by redboot.
arch/mips/mach-mscc/dram.c +1 -1
@@ -19,7 +19,7 @@ static inline int vcoreiii_train_bytelane(void) ret =hal_vcoreiii_train_bytelane (0 ); -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )if (ret)return ret; ret =hal_vcoreiii_train_bytelane (1 );
arch/mips/mach-mscc/include/mach/common.h +5 -0
@@ -16,6 +16,11 @@#include <mach/luton/luton_devcpu_gcb.h> #include <mach/luton/luton_devcpu_gcb_miim_regs.h> #include <mach/luton/luton_icpu_cfg.h> +#elif defined(CONFIG_SOC_JR2 ) +#include <mach/jr2/jr2.h> +#include <mach/jr2/jr2_devcpu_gcb.h> +#include <mach/jr2/jr2_devcpu_gcb_miim_regs.h> +#include <mach/jr2/jr2_icpu_cfg.h> #else #error Unsupported platform#endif
arch/mips/mach-mscc/include/mach/ddr.h +31 -7
@@ -161,7 +161,7 @@#endif -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )#define MIPS_VCOREIII_MEMORY_16BIT 1#endif
@@ -239,7 +239,7 @@ICPU_MEMCTRL_CFG_MSB_ROW_ADDR (VC3_MPAR_row_addr_cnt -1 ) | \ ICPU_MEMCTRL_CFG_MSB_COL_ADDR(VC3_MPAR_col_addr_cnt - 1) -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )#define MSCC_MEMPARM_PERIOD \ ICPU_MEMCTRL_REF_PERIOD_MAX_PEND_REF(8) | \ ICPU_MEMCTRL_REF_PERIOD_REF_PERIOD(VC3_MPAR_tREFI)
@@ -378,7 +378,7 @@ static inline void memphy_soft_reset(void)PAUSE (); } -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )static u8 training_data[] = {0xfe ,0x11 ,0x33 ,0x55 ,0x77 ,0x99 ,0xbb ,0xdd };static inline void sleep_100ns (u32 val)
@@ -398,6 +398,7 @@ static inline void sleep_100ns(u32 val) ; } +#if defined(CONFIG_SOC_OCELOT )static inline void hal_vcoreiii_ddr_reset_assert (void ) {/* DDR has reset pin on GPIO 19 toggle Low-High to release */
@@ -448,6 +449,26 @@ static inline void hal_vcoreiii_ddr_failed(void)panic ("DDR init failed\n" ); } +#else /* JR2 */ +static inline void hal_vcoreiii_ddr_reset_assert (void ) +{ +/* Ensure the memory controller physical iface is forced reset */ +writel (readl (BASE_CFG +ICPU_MEMPHY_CFG ) | +ICPU_MEMPHY_CFG_PHY_RST ,BASE_CFG +ICPU_MEMPHY_CFG ); + +/* Ensure the memory controller is forced reset */ +writel (readl (BASE_CFG +ICPU_RESET ) | +ICPU_RESET_MEM_RST_FORCE ,BASE_CFG +ICPU_RESET ); +} + +static inline void hal_vcoreiii_ddr_failed (void ) +{ +writel (0 ,BASE_CFG +ICPU_RESET ); +writel (PERF_SOFT_RST_SOFT_CHIP_RST ,BASE_CFG +PERF_SOFT_RST ); + +panic ("DDR init failed\n" ); +} +#endif /* * DDR memory sanity checking done, possibly enable ECC.
@@ -738,7 +759,7 @@ static inline void hal_vcoreiii_init_memctl(void)/* Wait for ZCAL to clear */ while (readl (BASE_CFG +ICPU_MEMPHY_ZCAL ) &ICPU_MEMPHY_ZCAL_ZCAL_ENA ) ; -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )/* Check no ZCAL_ERR */ if (readl (BASE_CFG +ICPU_MEMPHY_ZCAL_STAT ) &ICPU_MEMPHY_ZCAL_STAT_ZCAL_ERR )
@@ -752,7 +773,7 @@ static inline void hal_vcoreiii_init_memctl(void)writel (MSCC_MEMPARM_MEMCFG ,BASE_CFG +ICPU_MEMCTRL_CFG );writel (MSCC_MEMPARM_PERIOD ,BASE_CFG +ICPU_MEMCTRL_REF_PERIOD ); -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )writel (MSCC_MEMPARM_TIMING0 ,BASE_CFG +ICPU_MEMCTRL_TIMING0 );#else /* Luton */ clrbits_le32 (BASE_CFG +ICPU_MEMCTRL_TIMING0 , ((1 <<20 ) -1 ));
@@ -767,7 +788,7 @@ static inline void hal_vcoreiii_init_memctl(void)writel (MSCC_MEMPARM_MR2 ,BASE_CFG +ICPU_MEMCTRL_MR2_VAL );writel (MSCC_MEMPARM_MR3 ,BASE_CFG +ICPU_MEMCTRL_MR3_VAL ); -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT )/* Termination setup - enable ODT */ writel(ICPU_MEMCTRL_TERMRES_CTRL_LOCAL_ODT_RD_ENA |/* Assert ODT0 for any write */
@@ -778,6 +799,9 @@ static inline void hal_vcoreiii_init_memctl(void)hal_vcoreiii_ddr_reset_release ();writel (readl (BASE_CFG +ICPU_GPR (7 )) +1 ,BASE_CFG +ICPU_GPR (7 )); +#elif defined(CONFIG_SOC_JR2 ) +writel (ICPU_MEMCTRL_TERMRES_CTRL_ODT_WR_ENA (3 ), +BASE_CFG +ICPU_MEMCTRL_TERMRES_CTRL );#else /* Luton */ /* Termination setup - disable ODT */ writel (0 ,BASE_CFG +ICPU_MEMCTRL_TERMRES_CTRL );
@@ -796,7 +820,7 @@ static inline void hal_vcoreiii_wait_memctl(void)/* Settle...? */ sleep_100ns (10000 ); -#ifdef CONFIG_SOC_OCELOT +#if defined(CONFIG_SOC_OCELOT ) || defined(CONFIG_SOC_JR2 )/* Establish data contents in DDR RAM for training */ __raw_writel (0xcacafefe , ((void __iomem *)MSCC_DDR_TO ));
arch/mips/mach-mscc/include/mach/jr2/jr2.h new file +24 -0
@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* +* Microsemi Jaguar2 Switch driver +* +* Copyright (c) 2018 Microsemi Corporation +*/ + +#ifndef _MSCC_JR2_H_ +#define _MSCC_JR2_H_ + +#include <linux/bitops.h> +#include <dm.h> + +/* +* Target offset base(s) +*/ +#define MSCC_IO_ORIGIN1_OFFSET 0x70000000 +#define MSCC_IO_ORIGIN1_SIZE 0x00200000 +#define MSCC_IO_ORIGIN2_OFFSET 0x71000000 +#define MSCC_IO_ORIGIN2_SIZE 0x01000000 +#define BASE_CFG ((void __iomem *)0x70000000) +#define BASE_DEVCPU_GCB ((void __iomem *)0x71010000) + +#endif
arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h new file +20 -0
@@ -0,0 +1,20 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* +* Copyright (c) 2018 Microsemi Corporation +*/ + +#ifndef _MSCC_JR2_DEVCPU_GCB_H_ +#define _MSCC_JR2_DEVCPU_GCB_H_ + +#define PERF_GPR 0x4 + +#define PERF_SOFT_RST 0x8 + +#define PERF_SOFT_RST_SOFT_NON_CFG_RST BIT(2) +#define PERF_SOFT_RST_SOFT_SWC_RST BIT(1) +#define PERF_SOFT_RST_SOFT_CHIP_RST BIT(0) + +#define GPIO_GPIO_ALT (x) (0x78 + 4 * (x)) +#define GPIO_GPIO_ALT1 (x) (0x80 + 4 * (x)) + +#endif
arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb_miim_regs.h new file +25 -0
@@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* +* Copyright (c) 2018 Microsemi Corporation +*/ + +#ifndef _MSCC_JR2_DEVCPU_GCB_MIIM_REGS_H_ +#define _MSCC_JR2_DEVCPU_GCB_MIIM_REGS_H_ + +#define MIIM_MII_STATUS (gi) (0xc8 + (gi * 36)) +#define MIIM_MII_CMD (gi) (0xd0 + (gi * 36)) +#define MIIM_MII_DATA (gi) (0xd4 + (gi * 36)) + +#define MSCC_F_MII_STATUS_MIIM_STAT_BUSY (x) ((x) ? BIT(3) : 0) + +#define MSCC_F_MII_CMD_MIIM_CMD_VLD (x) ((x) ? BIT(31) : 0) +#define MSCC_F_MII_CMD_MIIM_CMD_PHYAD (x) (GENMASK(29, 25) & ((x) << 25)) +#define MSCC_F_MII_CMD_MIIM_CMD_REGAD (x) (GENMASK(24, 20) & ((x) << 20)) +#define MSCC_F_MII_CMD_MIIM_CMD_WRDATA (x) (GENMASK(19, 4) & ((x) << 4)) +#define MSCC_F_MII_CMD_MIIM_CMD_OPR_FIELD (x) (GENMASK(2, 1) & ((x) << 1)) +#define MSCC_F_MII_CMD_MIIM_CMD_SCAN (x) ((x) ? BIT(0) : 0) + +#define MSCC_M_MII_DATA_MIIM_DATA_SUCCESS GENMASK(17, 16) +#define MSCC_X_MII_DATA_MIIM_DATA_RDDATA (x) (((x) >> 0) & GENMASK(15, 0)) + +#endif
arch/mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h new file +321 -0
321 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 2/7 MSCC: Add support for Jaguar2 SOC family
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 4 lines
As the Ocelot and Luton SoCs, this family of SoCs are found in Microsemi Switches solution.
Signed-off-by Horatiu Vultur <[email protected]>
Quoted 16 lines
--- arch/mips/mach-mscc/Kconfig | 9 + arch/mips/mach-mscc/cpu.c | 7 + arch/mips/mach-mscc/dram.c | 2 +- arch/mips/mach-mscc/include/mach/common.h | 5 + arch/mips/mach-mscc/include/mach/ddr.h | 38 ++- arch/mips/mach-mscc/include/mach/jr2/jr2.h | 24 ++ .../mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h | 20 ++ .../include/mach/jr2/jr2_devcpu_gcb_miim_regs.h | 25 ++ .../mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h | 321 +++++++++++++++++++++ 9 files changed, 443 insertions(+), 8 deletions(-) create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_devcpu_gcb_miim_regs.h create mode 100644 arch/mips/mach-mscc/include/mach/jr2/jr2_icpu_cfg.h
Signature · 1 line
- Daniel
PATCH v2 3/7 MSCC: Add device tree for Jaguar2 board
In reply to Horatiu VulturAdd device tree based on evaluation board pcb110.
--- MAINTAINERS | 1 + arch/mips/dts/jr2_pcb110.dts | 74 +++++++++++++++++ arch/mips/dts/mscc,jr2.dtsi | 187 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 262 insertions(+) create mode 100644 arch/mips/dts/jr2_pcb110.dts create mode 100644 arch/mips/dts/mscc,jr2.dtsi
MAINTAINERS +1 -0
@@ -521,6 +521,7 @@ F: arch/mips/mach-mscc/ F: arch/mips/dts/luton* F: arch/mips/dts/mscc* F: arch/mips/dts/ocelot* +F: arch/mips/dts/jr2* F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c
arch/mips/dts/jr2_pcb110.dts new file +74 -0
74 lines not on this page · raw message
arch/mips/dts/mscc,jr2.dtsi new file +187 -0
187 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 4/7 MSCC: Add device tree for Jaguar2-48 board
In reply to Horatiu VulturAdd device tree based on evaluation board pcb111.
--- arch/mips/dts/jr2_pcb111.dts | 74 ++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 74 insertions(+) create mode 100644 arch/mips/dts/jr2_pcb111.dts
arch/mips/dts/jr2_pcb111.dts new file +74 -0
@@ -0,0 +1,74 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2018 Microsemi Corporation + */ + +/dts-v1/; +#include "mscc,jr2.dtsi" + +/ { + model = "Jaguar2 Cu48 PCB111 Reference Board"; + compatible = "mscc,jr2-pcb111", "mscc,jr2"; + + aliases { + spi0 = &spi0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-leds { + compatible = "gpio-leds"; + + status_green { + label = "pcb111:green:status"; + gpios = <&gpio 12 0>; + default-state = "on"; + }; + + status_red { + label = "pcb111:red:status"; + gpios = <&gpio 13 0>; + default-state = "off"; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + spi-flash at 0 { + compatible = "spi-flash"; + spi-max-frequency = <18000000>; /* input clock */ + reg = <0>; /* CS0 */ + }; +}; + +&gpio { + /* SPIO only use DO, CLK, no inputs */ + sgpio1_pins: sgpio1-pins { + pins = "GPIO_4", "GPIO_5"; + function = "sio1"; + }; +}; + +&sgpio { + status = "okay"; + sgpio-ports = <0xffffffff>; +}; + +&sgpio1 { + status = "okay"; + sgpio-ports = <0x001effff>; +}; + +&sgpio2 { + status = "okay"; + sgpio-ports = <0xff000000>; + gpio-ranges = <&sgpio2 0 0 96>; +};
Signature · 1 line
2.7.4
PATCH v2 5/7 MSCC: add device tree for Serval2 board
In reply to Horatiu VulturAdd device tree based on evaluation board pcb112.
--- MAINTAINERS | 1 + arch/mips/dts/serval2_pcb112.dts | 60 ++++++++++++++++++++++++++++++++++++++++ 2 files changed, 61 insertions(+) create mode 100644 arch/mips/dts/serval2_pcb112.dts
MAINTAINERS +1 -0
@@ -522,6 +522,7 @@ F: arch/mips/dts/luton* F: arch/mips/dts/mscc* F: arch/mips/dts/ocelot* F: arch/mips/dts/jr2* +F: arch/mips/dts/serval* F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c
arch/mips/dts/serval2_pcb112.dts new file +60 -0
60 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 6/7 MSCC: Add board support for Jaguar2 SOC family
In reply to Horatiu VulturAdd board support and configuration for Jaguar2 SOC family. The detection of the board type in this family is based on the phy ids.
--- arch/mips/dts/Makefile | 1 + arch/mips/mach-mscc/Makefile | 5 +- board/mscc/common/Makefile | 4 ++ board/mscc/common/spi.c | 31 ++++++++++++ board/mscc/jr2/Kconfig | 15 ++++++ board/mscc/jr2/Makefile | 4 ++ board/mscc/jr2/jr2.c | 117 +++++++++++++++++++++++++++++++++++++++++++ board/mscc/ocelot/ocelot.c | 22 -------- configs/mscc_jr2_defconfig | 59 ++++++++++++++++++++++ 9 files changed, 234 insertions(+), 24 deletions(-) create mode 100644 board/mscc/common/Makefile create mode 100644 board/mscc/common/spi.c create mode 100644 board/mscc/jr2/Kconfig create mode 100644 board/mscc/jr2/Makefile create mode 100644 board/mscc/jr2/jr2.c create mode 100644 configs/mscc_jr2_defconfig
arch/mips/dts/Makefile +1 -0
@@ -19,6 +19,7 @@ dtb-$(CONFIG_BOARD_TPLINK_WDR4300) += tplink_wdr4300.dtb dtb-$(CONFIG_TARGET_JZ4780_CI20) += ci20.dtb dtb-$(CONFIG_SOC_LUTON) += luton_pcb090.dtb luton_pcb091.dtb dtb-$(CONFIG_SOC_OCELOT) += ocelot_pcb120.dtb ocelot_pcb123.dtb +dtb-$(CONFIG_SOC_JR2) += jr2_pcb110.dtb jr2_pcb111.dtb serval2_pcb112.dtb targets += $(dtb-y)
arch/mips/mach-mscc/Makefile +3 -2
@@ -2,5 +2,6 @@ CFLAGS_cpu.o += -finline-limit=64000 -obj-y += cpu.o dram.o reset.o phy.o gpio.o lowlevel_init.o -obj-$(CONFIG_SOC_LUTON) += lowlevel_init_luton.o +obj-y += cpu.o dram.o reset.o phy.o lowlevel_init.o +obj-$(CONFIG_SOC_LUTON) += lowlevel_init_luton.o gpio.o +obj-$(CONFIG_SOC_OCELOT) += gpio.o
board/mscc/common/Makefile new file +4 -0
@@ -0,0 +1,4 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +obj-$(CONFIG_SOC_JR2) := spi.o +obj-$(CONFIG_SOC_OCELOT) := spi.o
board/mscc/common/spi.c new file +31 -0
@@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* +* Copyright (c) 2018 Microsemi Coprporation +*/ + +#include <common.h> +#include <asm/io.h> +#include <spi.h> + +void external_cs_manage (struct udevice *dev,bool enable) +{ +u32 cs =spi_chip_select (dev); +/* IF_SI0_OWNER, select the owner of the SI interface +* Encoding: 0: SI Slave +* 1: SI Boot Master +* 2: SI Master Controller +*/ +if (!enable) { +writel (ICPU_SW_MODE_SW_PIN_CTRL_MODE | +ICPU_SW_MODE_SW_SPI_CS (BIT (cs)), +BASE_CFG +ICPU_SW_MODE ); +clrsetbits_le32 (BASE_CFG +ICPU_GENERAL_CTRL , +ICPU_GENERAL_CTRL_IF_SI_OWNER_M , +ICPU_GENERAL_CTRL_IF_SI_OWNER (2 )); + }else { +writel (0 ,BASE_CFG +ICPU_SW_MODE ); +clrsetbits_le32 (BASE_CFG +ICPU_GENERAL_CTRL , +ICPU_GENERAL_CTRL_IF_SI_OWNER_M , +ICPU_GENERAL_CTRL_IF_SI_OWNER (1 )); + } +}
board/mscc/jr2/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +config SYS_VENDOR + default "mscc" + +if SOC_JR2 + +config SYS_BOARD + default "jr2" + +config SYS_CONFIG_NAME + default "jr2" + +endif +
board/mscc/jr2/Makefile new file +4 -0
@@ -0,0 +1,4 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) + +obj-$(CONFIG_SOC_JR2) := jr2.o +
board/mscc/jr2/jr2.c new file +117 -0
117 lines not on this page · raw message
board/mscc/ocelot/ocelot.c +0 -22
@@ -18,28 +18,6 @@ enum { BOARD_TYPE_PCB123, }; -void external_cs_manage (struct udevice *dev,bool enable) -{ -u32 cs =spi_chip_select (dev); -/* IF_SI0_OWNER, select the owner of the SI interface -* Encoding: 0: SI Slave -* 1: SI Boot Master -* 2: SI Master Controller -*/ -if (!enable) { -writel (ICPU_SW_MODE_SW_PIN_CTRL_MODE | -ICPU_SW_MODE_SW_SPI_CS (BIT (cs)),BASE_CFG +ICPU_SW_MODE ); -clrsetbits_le32 (BASE_CFG +ICPU_GENERAL_CTRL , -ICPU_GENERAL_CTRL_IF_SI_OWNER_M , -ICPU_GENERAL_CTRL_IF_SI_OWNER (2 )); - }else { -writel (0 ,BASE_CFG +ICPU_SW_MODE ); -clrsetbits_le32 (BASE_CFG +ICPU_GENERAL_CTRL , -ICPU_GENERAL_CTRL_IF_SI_OWNER_M , -ICPU_GENERAL_CTRL_IF_SI_OWNER (1 )); - } -} -void board_debug_uart_init (void ) {/* too early for the pinctrl driver, so configure the UART pins here */
configs/mscc_jr2_defconfig new file +59 -0
59 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 6/7 MSCC: Add board support for Jaguar2 SOC family
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 13 lines
Add board support and configuration for Jaguar2 SOC family. The detection of the board type in this family is based on the phy ids.
Signed-off-by Horatiu Vultur <[email protected]>--- arch/mips/dts/Makefile | 1 + arch/mips/mach-mscc/Makefile | 5 +- board/mscc/common/Makefile | 4 ++ board/mscc/common/spi.c | 31 ++++++++++++ board/mscc/jr2/Kconfig | 15 ++++++ board/mscc/jr2/Makefile | 4 ++ board/mscc/jr2/jr2.c | 117 +++++++++++++++++++++++++++++++++++++++++++ board/mscc/ocelot/ocelot.c | 22 --------
Quoted 9 lines
configs/mscc_jr2_defconfig | 59 ++++++++++++++++++++++ 9 files changed, 234 insertions(+), 24 deletions(-) create mode 100644 board/mscc/common/Makefile create mode 100644 board/mscc/common/spi.c create mode 100644 board/mscc/jr2/Kconfig create mode 100644 board/mscc/jr2/Makefile create mode 100644 board/mscc/jr2/jr2.c create mode 100644 configs/mscc_jr2_defconfig
Signature · 1 line
- Daniel
PATCH v2 7/7 MSCC: Add sysreset driver for Jaguar2 SOC family
In reply to Horatiu VulturCreate sysreset driver for Jaguar2 SOC family and update defconfig to use it.
--- MAINTAINERS | 1 + board/mscc/jr2/jr2.c | 8 +++++++ configs/mscc_jr2_defconfig | 2 ++ drivers/sysreset/Kconfig | 6 ++++++ drivers/sysreset/Makefile | 1 + drivers/sysreset/sysreset_jr2.c | 46 +++++++++++++++++++++++++++++++++++++++++ 6 files changed, 64 insertions(+) create mode 100644 drivers/sysreset/sysreset_jr2.c
MAINTAINERS +1 -0
@@ -526,6 +526,7 @@ F: arch/mips/dts/serval* F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c +F: drivers/sysreset/sysreset_jr2.c F: include/configs/vcoreiii.h F: drivers/pinctrl/mscc/
board/mscc/jr2/jr2.c +8 -0
@@ -6,6 +6,7 @@#include <common.h> #include <asm/io.h> #include <led.h> +#include <dm/lists.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -17,6 +18,8 @@ enum {int board_early_init_r (void ) { +int ret; +/* Prepare SPI controller to be used in master mode */ writel (0 ,BASE_CFG +ICPU_SW_MODE ); clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL,
@@ -30,6 +33,11 @@ int board_early_init_r(void)if (IS_ENABLED (CONFIG_LED ))led_default_state (); + ret =device_bind_driver (gd->dm_root,"jr2_soft_reset" , +"reset_soft" ,NULL ); +if (ret) +printf ("Warning: No reset driver: ret=%d\n" , ret); +return 0 ; }
configs/mscc_jr2_defconfig +2 -0
@@ -57,3 +57,5 @@ CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_LZMA=y CONFIG_XZ=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_JR2=y
drivers/sysreset/Kconfig +6 -0
@@ -43,6 +43,12 @@ config SYSRESET_TI_SCI This enables the system reset driver support over TI System Control Interface available on some new TI's SoCs. +config SYSRESET_JR2 + bool "Enable support for Jaguar2 soft reset" + depends on SOC_JR2 + help + This is soft reset on Jaguar2. + endif config SYSRESET_SYSCON
drivers/sysreset/Makefile +1 -0
@@ -16,3 +16,4 @@ obj-$(CONFIG_SYSRESET_SYSCON) += sysreset_syscon.o obj-$(CONFIG_SYSRESET_WATCHDOG) += sysreset_watchdog.o obj-$(CONFIG_SYSRESET_X86) += sysreset_x86.o obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o +obj-$(CONFIG_SYSRESET_JR2) += sysreset_jr2.o
drivers/sysreset/sysreset_jr2.c new file +46 -0
46 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH v2 7/7 MSCC: Add sysreset driver for Jaguar2 SOC family
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 48 lines
Create sysreset driver for Jaguar2 SOC family and update defconfig to use it.
Signed-off-by Horatiu Vultur <[email protected]>--- MAINTAINERS | 1 + board/mscc/jr2/jr2.c | 8 +++++++ configs/mscc_jr2_defconfig | 2 ++ drivers/sysreset/Kconfig | 6 ++++++ drivers/sysreset/Makefile | 1 + drivers/sysreset/sysreset_jr2.c | 46 +++++++++++++++++++++++++++++++++++++++++ 6 files changed, 64 insertions(+) create mode 100644 drivers/sysreset/sysreset_jr2.cMAINTAINERS +1
-0@@ -526,6 +526,7 @@ F: arch/mips/dts/serval* F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c +F: drivers/sysreset/sysreset_jr2.c F: include/configs/vcoreiii.h F: drivers/pinctrl/mscc/board/mscc/jr2/jr2.c +3
-0@@ -6,6 +6,7 @@#include <common.h> #include <asm/io.h> #include <led.h> +#include <dm/lists.h> DECLARE_GLOBAL_DATA_PTR ;@@ -17,6 +18,8 @@ enum {int board_early_init_r (void ) { +int ret; +/* Prepare SPI controller to be used in master mode */ writel (0 ,BASE_CFG +ICPU_SW_MODE ); clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL,
board/mscc/jr2/jr2.c int board_early_init_r(void) · line 40
Quoted 8 lines
board/mscc/jr2/jr2.c +5
-0@@ -30,6 +33,11 @@ int board_early_init_r(void)if (IS_ENABLED (CONFIG_LED ))led_default_state (); + ret =device_bind_driver (gd->dm_root,"jr2_soft_reset" , +"reset_soft" ,NULL ); +if (ret) +printf ("Warning: No reset driver: ret=%d\n" , ret); +
that shouldn't be necessary if you put a device node to device tree.
Actually my intention in last review was that you create a driver which fits all MSCC SoCs and control the differences via the device tree compatible string. This way you could entirely get rid of the legacy _machine_restart() hook in the MSCC platform. But you don't have to do this in this series.
Quoted 45 lines
board/mscc/jr2/jr2.c +0
-0return 0 ; }configs/mscc_jr2_defconfig +2
-0@@ -57,3 +57,5 @@ CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_LZMA=y CONFIG_XZ=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_JR2=ydrivers/sysreset/Kconfig +6
-0@@ -43,6 +43,12 @@ config SYSRESET_TI_SCI This enables the system reset driver support over TI System Control Interface available on some new TI's SoCs. +config SYSRESET_JR2 + bool "Enable support for Jaguar2 soft reset" + depends on SOC_JR2 + help + This is soft reset on Jaguar2. + endif config SYSRESET_SYSCONdrivers/sysreset/Makefile +1
-0@@ -16,3 +16,4 @@ obj-$(CONFIG_SYSRESET_SYSCON) += sysreset_syscon.o obj-$(CONFIG_SYSRESET_WATCHDOG) += sysreset_watchdog.o obj-$(CONFIG_SYSRESET_X86) += sysreset_x86.o obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o +obj-$(CONFIG_SYSRESET_JR2) += sysreset_jr2.odrivers/sysreset/sysreset_jr2.c new file +0
-0
drivers/sysreset/sysreset_jr2.c line 6
Quoted 6 lines
drivers/sysreset/sysreset_jr2.c new file +6
-0@@ -0,0 +1,46 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* +* Microsemi SoCs pinctrl driver +* +* Author: <[email protected]> +* License: Dual MIT/GPL
redundant due to SPDX identifier
Quoted 4 lines
drivers/sysreset/sysreset_jr2.c new file +4
-0+* Copyright (c) 2018 Microsemi Corporation +*/ + +#include <common.h>
drivers/sysreset/sysreset_jr2.c line 20
Quoted 10 lines
drivers/sysreset/sysreset_jr2.c new file +10
-0+#include <dm.h> +#include <errno.h> +#include <sysreset.h> +#include <linux/err.h> +#include <asm/io.h> + +static int jr2_sysreset_request (struct udevice *dev, +enum sysreset_t type) +{ + registeru32 reg =readl (BASE_CFG +ICPU_GENERAL_CTRL );
register is not required in this context
Quoted 27 lines
drivers/sysreset/sysreset_jr2.c new file +26
-0+/* Set owner */ + reg &= ~ICPU_GENERAL_CTRL_IF_SI_OWNER_M ; + reg |=ICPU_GENERAL_CTRL_IF_SI_OWNER (1 ); +/* Set boot mode */ + reg |=ICPU_GENERAL_CTRL_BOOT_MODE_ENA ; +writel (reg,BASE_CFG +ICPU_GENERAL_CTRL ); +/* Read back in order to make BOOT mode setting active */ + reg =readl (BASE_CFG +ICPU_GENERAL_CTRL ); +/* Reset CPU only - still executing _here_. but from cache */ +writel (readl (BASE_CFG +ICPU_RESET ) | +ICPU_RESET_CORE_RST_CPU_ONLY | +ICPU_RESET_CORE_RST_FORCE , +BASE_CFG +ICPU_RESET ); + +return -EINPROGRESS ; +} + +static struct sysreset_ops jr2_sysreset = { + .request = jr2_sysreset_request, +}; + +U_BOOT_DRIVER (sysreset_jr2) = { + .id =UCLASS_SYSRESET , + .name ="jr2_soft_reset" , + .ops = &jr2_sysreset, +};
Signature · 1 line
- Daniel
PATCH v2 7/7 MSCC: Add sysreset driver for Jaguar2 SOC family
Hi Daniel,
Quoted 62 lines · Daniel Schwierzeck
Am 07.01.19 um 14:02 schrieb Horatiu Vultur:
Quoted 48 lines
Create sysreset driver for Jaguar2 SOC family and update defconfig to use it.
Signed-off-by Horatiu Vultur <[email protected]>--- MAINTAINERS | 1 + board/mscc/jr2/jr2.c | 8 +++++++ configs/mscc_jr2_defconfig | 2 ++ drivers/sysreset/Kconfig | 6 ++++++ drivers/sysreset/Makefile | 1 + drivers/sysreset/sysreset_jr2.c | 46 +++++++++++++++++++++++++++++++++++++++++ 6 files changed, 64 insertions(+) create mode 100644 drivers/sysreset/sysreset_jr2.cMAINTAINERS +1
-0@@ -526,6 +526,7 @@ F: arch/mips/dts/serval* F: board/mscc/ F: configs/mscc* F: drivers/gpio/mscc_sgpio.c +F: drivers/sysreset/sysreset_jr2.c F: include/configs/vcoreiii.h F: drivers/pinctrl/mscc/board/mscc/jr2/jr2.c +3
-0@@ -6,6 +6,7 @@#include <common.h> #include <asm/io.h> #include <led.h> +#include <dm/lists.h> DECLARE_GLOBAL_DATA_PTR ;@@ -17,6 +18,8 @@ enum {int board_early_init_r (void ) { +int ret; +/* Prepare SPI controller to be used in master mode */ writel (0 ,BASE_CFG +ICPU_SW_MODE ); clrsetbits_le32(BASE_CFG + ICPU_GENERAL_CTRL,board/mscc/jr2/jr2.c int board_early_init_r(void) · line 40
Quoted 8 lines
board/mscc/jr2/jr2.c +5
-0@@ -30,6 +33,11 @@ int board_early_init_r(void)if (IS_ENABLED (CONFIG_LED ))led_default_state (); + ret =device_bind_driver (gd->dm_root,"jr2_soft_reset" , +"reset_soft" ,NULL ); +if (ret) +printf ("Warning: No reset driver: ret=%d\n" , ret); +that shouldn't be necessary if you put a device node to device tree.
Quoted 5 lines
Actually my intention in last review was that you create a driver which fits all MSCC SoCs and control the differences via the device tree compatible string. This way you could entirely get rid of the legacy
_machine_restart()hook in the MSCC platform. But you don't have to do this in this series.
Ah, now it is more clear. I will create a different patch for this and fix it for all MSCC SoCs.
Quoted 102 lines
Quoted 46 lines
board/mscc/jr2/jr2.c +0
-0return 0 ; }configs/mscc_jr2_defconfig +2
-0@@ -57,3 +57,5 @@ CONFIG_SPI=y CONFIG_DM_SPI=y CONFIG_LZMA=y CONFIG_XZ=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_JR2=ydrivers/sysreset/Kconfig +6
-0@@ -43,6 +43,12 @@ config SYSRESET_TI_SCI This enables the system reset driver support over TI System Control Interface available on some new TI's SoCs. +config SYSRESET_JR2 + bool "Enable support for Jaguar2 soft reset" + depends on SOC_JR2 + help + This is soft reset on Jaguar2. + endif config SYSRESET_SYSCONdrivers/sysreset/Makefile +1
-0@@ -16,3 +16,4 @@ obj-$(CONFIG_SYSRESET_SYSCON) += sysreset_syscon.o obj-$(CONFIG_SYSRESET_WATCHDOG) += sysreset_watchdog.o obj-$(CONFIG_SYSRESET_X86) += sysreset_x86.o obj-$(CONFIG_TARGET_XTFPGA) += sysreset_xtfpga.o +obj-$(CONFIG_SYSRESET_JR2) += sysreset_jr2.odrivers/sysreset/sysreset_jr2.c new file +0
-0drivers/sysreset/sysreset_jr2.c line 6
Quoted 6 lines
drivers/sysreset/sysreset_jr2.c new file +6
-0@@ -0,0 +1,46 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* +* Microsemi SoCs pinctrl driver +* +* Author: <[email protected]> +* License: Dual MIT/GPL redundant due to SPDX identifier
Quoted 4 lines
drivers/sysreset/sysreset_jr2.c new file +4
-0+* Copyright (c) 2018 Microsemi Corporation +*/ + +#include <common.h> drivers/sysreset/sysreset_jr2.c line 20
Quoted 10 lines
drivers/sysreset/sysreset_jr2.c new file +10
-0+#include <dm.h> +#include <errno.h> +#include <sysreset.h> +#include <linux/err.h> +#include <asm/io.h> + +static int jr2_sysreset_request (struct udevice *dev, +enum sysreset_t type) +{ + registeru32 reg =readl (BASE_CFG +ICPU_GENERAL_CTRL );register is not required in this context
Quoted 27 lines
drivers/sysreset/sysreset_jr2.c new file +26
-0+/* Set owner */ + reg &= ~ICPU_GENERAL_CTRL_IF_SI_OWNER_M ; + reg |=ICPU_GENERAL_CTRL_IF_SI_OWNER (1 ); +/* Set boot mode */ + reg |=ICPU_GENERAL_CTRL_BOOT_MODE_ENA ; +writel (reg,BASE_CFG +ICPU_GENERAL_CTRL ); +/* Read back in order to make BOOT mode setting active */ + reg =readl (BASE_CFG +ICPU_GENERAL_CTRL ); +/* Reset CPU only - still executing _here_. but from cache */ +writel (readl (BASE_CFG +ICPU_RESET ) | +ICPU_RESET_CORE_RST_CPU_ONLY | +ICPU_RESET_CORE_RST_FORCE , +BASE_CFG +ICPU_RESET ); + +return -EINPROGRESS ; +} + +static struct sysreset_ops jr2_sysreset = { + .request = jr2_sysreset_request, +}; + +U_BOOT_DRIVER (sysreset_jr2) = { + .id =UCLASS_SYSRESET , + .name ="jr2_soft_reset" , + .ops = &jr2_sysreset, +};Signature · 1 line
- Daniel
Signature · 1 line
/Horatiu