Skip to contentSkip to conversation

device tree in open firmware on power6

DISCUSSION Chandru 2 participants 2 messages May 8, 2008

lore
Share & tools
lore

Chandru

author
#0 lore raw

Hi,

When I set linux 2.6.26-rc1 as default kernel to boot in /etc/yaboot.conf, then the device tree in open firmware shows only one memory node ( the same memory node appears in /proc/device-tree/memory@0 ). But when RHEL5.2 kernel is set as default in /etc/yaboot.conf then the device tree in open firmware shows plenty of memory nodes. Following is the open firmware output..

linux-2.6.26-rc1:

<snip>
0 > dev / ls
...
000000caf1b8: /PowerPC,POWER6@6
000000cb0120: /memory@0
000000cb83d8: /ibm,dynamic-reconfiguration-memory
000000cbcd60: /options
...

0 > dev /memory@0 ok
0 > .properties

name                    memory
device_type             memory
reg                     00000000 00000000  00000000 08000000
available               00000000 00004000 00000000 00bfc000 00000000 02020000
00000000 05fe0000
#address-cells          00000001
#size-cells             00000000
ibm,phandle             fffffffa
ibm,associativity       00000004 00000000 00000000 00000000 00000000

<snip-end>

when default=RHEL5.2:

0 > dev / ls 000000c8d200: /ibm,serial
000000c8dff8: /chosen
...
000000cae2c0: /PowerPC,POWER6@4
000000caf1b8: /PowerPC,POWER6@6
000000cb0120: /memory@0
000000cb5af0: /memory@8000000
000000cb5ce0: /memory@c000000
000000cb5ed0: /memory@10000000
000000cb60c0: /memory@14000000
000000cb62b0: /memory@18000000
000000cb64a0: /memory@1c000000
000000cb6690: /memory@20000000

...

The open firmware environment variable "ibm,fw-new-mem-def" is false for rhel5.2 kernel where as it is 'true' for 2.6.26-rc1 as default kernel to boot. Any inputs if the one memory node in 2.6.26-rc1 should show the size of available system memory ?, or there should be many memory nodes for 2.6.26-rc1 ?.

Thanks,
Chandru

#1 lore raw
Quoted 6 lines · Chandru

When I set linux 2.6.26-rc1 as default kernel to boot in /etc/yaboot.conf, then the device tree in open firmware shows only one memory node ( the same memory node appears in /proc/device-tree/memory@0 ). But when RHEL5.2 kernel is set as default in /etc/yaboot.conf then the device tree in open firmware shows plenty of memory nodes. Following is the open firmware output..

Current kernels tell the firmware that they can handle having memory represented in the /ibm,dynamic-reconfiguration-memory node, which is a more compact representation than having it represented in multiple /memory@xxx nodes. Therefore firmware reports most of the memory in the /ibm,dynamic-reconfiguration-memory node you have here:

Quoted 8 lines

linux-2.6.26-rc1:

<snip>
0 > dev / ls
...
000000caf1b8: /PowerPC,POWER6@6
000000cb0120: /memory@0
000000cb83d8: /ibm,dynamic-reconfiguration-memory

and only gives you one /memory@xxx node, which represents the real memory area. See sections C.6.2.3 and C.6.6.2 of PAPR for more information.

Paul.