Skip to contentSkip to conversation

re-activate lv after reboot ?

linux-lvm vu pham 3 participants 6 messages Apr 21, 2009 – Apr 23, 2009

lore
Share & tools
lore

vu pham

author
#0 lore raw

My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.

Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?

Thanks,
Vu

#1 lore raw
Quoted 2 lines · vu pham

My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.

In RH and Fedora you need to updated your initrd image to have the drivers for the disk access available before the real filesystems are mounted. You don't mention what distro you're using, so I'll avoid boring you with details that may not be pertinent to your situation.

Quoted 11 lines

Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?

Thanks,
Vu

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

author
#2 lore raw
Quoted 6 lines · Eric Brunson
Quoted 2 lines · vu pham

My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.

In RH and Fedora you need to updated your initrd image to have the drivers for the disk access available before the real filesystems are mounted. You don't mention what distro you're using, so I'll avoid boring you with details that may not be pertinent to your situation.

Hi Eric, thanks for your reply. I am using RHEL5.3

Thanks again.

Vu

#3 lore raw
Quoted 10 lines · vu pham
Quoted 6 lines · Eric Brunson
Quoted 2 lines · vu pham

My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.

In RH and Fedora you need to updated your initrd image to have the drivers for the disk access available before the real filesystems are mounted. You don't mention what distro you're using, so I'll avoid boring you with details that may not be pertinent to your situation.

Hi Eric, thanks for your reply. I am using RHEL5.3

In Fedora (and I assume RH) you can specify additional kernel modules to include in the initrd image:

foxtrot(~)$ cat /etc/sysconfig/mkinitrd
MODULES="usb-storage"

This will also "stick" across kernel upgrades as mkinitrd is part of the kernel post-install process.

I don't know anything about iscsiadm, if it's simply a kernel module, then you can add it as I added usb-storage, if it's a process that has to be running, that may be more difficult to add to your boot process.

That's the extent of my expertise, so maybe someone familiar with iscsiadm may chime in.

Hope that helps,
e.

#4 lore raw
In reply to vu pham
Quoted 9 lines · vu pham

My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.

Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?

First make sure node.startup is set to automatic in /etc/iscsi/iscsi.conf. Then you can edit /etc/fstab and mount your lv using _netdev.

--
Regards,
Edward Choi.

author
#5 lore raw
Quoted 7 lines · Edward Choi
Quoted 6 lines · vu pham

My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.

Quoted 7 lines
Quoted 3 lines

Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?

First make sure node.startup is set to automatic in /etc/iscsi/iscsi.conf. Then you can edit /etc/fstab and mount your lv using _netdev.

Hi Ed, thanks for your reply. I did not say clearly in my original post. The server accesses this iscsi device as the back-end disk device for some domUs so it never mounts the LVs as system files.

Vu