re-activate lv after reboot ?
My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command /etc/rcd./rc.local.
Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?
Thanks,
Vu
Quoted 2 lines · vu pham
My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command/etc/rcd./rc.local.
In RH and Fedora you need to updated your initrd image to have the drivers for the disk access available before the real filesystems are mounted. You don't mention what distro you're using, so I'll avoid boring you with details that may not be pertinent to your situation.
Quoted 11 lines
Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?
Thanks,
Vu_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
Quoted 6 lines · Eric Brunson
Quoted 2 lines · vu pham
My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command/etc/rcd./rc.local.In RH and Fedora you need to updated your initrd image to have the drivers for the disk access available before the real filesystems are mounted. You don't mention what distro you're using, so I'll avoid boring you with details that may not be pertinent to your situation.
Hi Eric, thanks for your reply. I am using RHEL5.3
Thanks again.
Vu
Quoted 10 lines · vu pham
Quoted 6 lines · Eric Brunson
Quoted 2 lines · vu pham
My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command/etc/rcd./rc.local.In RH and Fedora you need to updated your initrd image to have the drivers for the disk access available before the real filesystems are mounted. You don't mention what distro you're using, so I'll avoid boring you with details that may not be pertinent to your situation.
Hi Eric, thanks for your reply. I am using RHEL5.3
In Fedora (and I assume RH) you can specify additional kernel modules to include in the initrd image:
foxtrot(~)$ cat /etc/sysconfig/mkinitrd
MODULES="usb-storage"
This will also "stick" across kernel upgrades as mkinitrd is part of the kernel post-install process.
I don't know anything about iscsiadm, if it's simply a kernel module, then you can add it as I added usb-storage, if it's a process that has to be running, that may be more difficult to add to your boot process.
That's the extent of my expertise, so maybe someone familiar with iscsiadm may chime in.
Hope that helps,
e.
Quoted 9 lines · vu pham
My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command/etc/rcd./rc.local.Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?
First make sure node.startup is set to automatic in /etc/iscsi/iscsi.conf. Then you can edit /etc/fstab and mount your lv using _netdev.
--
Regards,
Edward Choi.
Quoted 7 lines · Edward Choi
Quoted 6 lines · vu pham
My server uses iscsiadm to access a remote iscsi device. VG and LV are created on that device and can be accessed just fine.
The problem is after reboot, the LVs are in inactive mode and I have to run vgchange -a y to activate the VG on the iscsi device or to put that command/etc/rcd./rc.local.
Quoted 7 lines
Quoted 3 lines
Is there any way to automatically to activate those LVs/VGs when the iscsi device starts ?
First make sure node.startup is set to automatic in
/etc/iscsi/iscsi.conf. Then you can edit/etc/fstaband mount your lv using_netdev.
Hi Ed, thanks for your reply. I did not say clearly in my original post. The server accesses this iscsi device as the back-end disk device for some domUs so it never mounts the LVs as system files.
Vu