Skip to contentSkip to conversation

phy: qcom-snps: Add runtime suspend and resume handlers

PATCH Superseded Wesley Cheng 2 participants 3 messages May 22, 2020 – Jun 25, 2020

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 phy: qcom-snps: Add runtime suspend and resume handlers

Allow for the PHY to be put into a powered down state when possible. Add the required suspend and resume callbacks, which will determine what resources can be turned off depending on the cable status.

---
Changes in v2:
- Addressed checkpatch alignment/line length warnings.
- Removed superfluous init in qcom_snps_hsphy_resume().

 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 100 ++++++++++++++++++++++++++
 1 file changed, 100 insertions(+)
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +100 -0
index 4d74045..0a4e77af 100644
@@ -76,7 +76,9 @@
  * @iface_clk: phy interface clock
  * @phy_reset: phy reset control
  * @vregs: regulator supplies bulk data
+ * @suspended: PHY is in the suspended state
  * @phy_initialized: if PHY has been initialized correctly
+ * @mode: contains the current mode the PHY is in
  */
 struct qcom_snps_hsphy {
 	struct phy *phy;
@@ -87,7 +89,9 @@ struct qcom_snps_hsphy {
 	struct reset_control *phy_reset;
 	struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS];
 
+	bool suspended;
 	bool phy_initialized;
+	enum phy_mode mode;
 };
 
 static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
@@ -104,6 +108,84 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
 	readl_relaxed(base + offset);
 }
 
+static int qcom_snps_hsphy_suspend(struct qcom_snps_hsphy *hsphy)
+{
+	if (hsphy->suspended)
+		return 0;
+
+	dev_dbg(&hsphy->phy->dev, "Suspend QCOM SNPS PHY, mode:%d\n",
+		hsphy->mode);
+
+	if (hsphy->mode == PHY_MODE_USB_HOST) {
+		/* Enable auto-resume to meet remote wakeup timing */
+		qcom_snps_hsphy_write_mask(hsphy->base,
+						USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+						USB2_AUTO_RESUME,
+						USB2_AUTO_RESUME);
+		usleep_range(500, 1000);
+		qcom_snps_hsphy_write_mask(hsphy->base,
+						USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+						0, USB2_AUTO_RESUME);
+	}
+
+	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+	hsphy->suspended = true;
+
+	return 0;
+}
+
+static int qcom_snps_hsphy_resume(struct qcom_snps_hsphy *hsphy)
+{
+	int ret;
+
+	if (!hsphy->suspended)
+		return 0;
+
+	dev_dbg(&hsphy->phy->dev, "Resume QCOM SNPS PHY, mode:%d\n",
+		hsphy->mode);
+
+	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
+	if (ret) {
+		dev_err(&hsphy->phy->dev,
+			"failed to enable cfg ahb clock, %d\n", ret);
+		return ret;
+	}
+
+	hsphy->suspended = false;
+	return 0;
+}
+
+static int __maybe_unused qcom_snps_hsphy_runtime_suspend(struct device *dev)
+{
+	struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
+
+	if (!hsphy->phy_initialized)
+		return 0;
+
+	qcom_snps_hsphy_suspend(hsphy);
+	return 0;
+}
+
+static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
+{
+	struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
+
+	if (!hsphy->phy_initialized)
+		return 0;
+
+	qcom_snps_hsphy_resume(hsphy);
+	return 0;
+}
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
+					int submode)
+{
+	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
+
+	hsphy->mode = mode;
+	return 0;
+}
+
 static int qcom_snps_hsphy_init(struct phy *phy)
 {
 	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
@@ -175,6 +257,7 @@ static int qcom_snps_hsphy_init(struct phy *phy)
 					UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0);
 
 	hsphy->phy_initialized = true;
+	hsphy->suspended = false;
 
 	return 0;
 
@@ -201,6 +284,7 @@ static int qcom_snps_hsphy_exit(struct phy *phy)
 static const struct phy_ops qcom_snps_hsphy_gen_ops = {
 	.init		= qcom_snps_hsphy_init,
 	.exit		= qcom_snps_hsphy_exit,
+	.set_mode	= qcom_snps_hsphy_set_mode,
 	.owner		= THIS_MODULE,
 };
 
@@ -212,6 +296,11 @@ static int qcom_snps_hsphy_exit(struct phy *phy)
 };
 MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_of_match_table);
 
+static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
+	SET_RUNTIME_PM_OPS(qcom_snps_hsphy_runtime_suspend,
+			   qcom_snps_hsphy_runtime_resume, NULL)
+};
+
 static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -255,6 +344,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Prevent runtime pm from being ON by default. Users can enable
+	 * it using power/control in sysfs.
+	 */
+	pm_runtime_forbid(dev);
+
 	generic_phy = devm_phy_create(dev, NULL, &qcom_snps_hsphy_gen_ops);
 	if (IS_ERR(generic_phy)) {
 		ret = PTR_ERR(generic_phy);
@@ -269,6 +366,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 	if (!IS_ERR(phy_provider))
 		dev_dbg(dev, "Registered Qcom-SNPS HS phy\n");
+	else
+		pm_runtime_disable(dev);
 
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
@@ -277,6 +376,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 	.probe		= qcom_snps_hsphy_probe,
 	.driver = {
 		.name	= "qcom-snps-hs-femto-v2-phy",
+		.pm = &qcom_snps_hsphy_pm_ops,
 		.of_match_table = qcom_snps_hsphy_of_match_table,
 	},
 };
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
maintainer
#1 lore raw

Hi Wesley,

Quoted 39 lines · Wesley Cheng

Allow for the PHY to be put into a powered down state when possible. Add the required suspend and resume callbacks, which will determine what resources can be turned off depending on the cable status.

---
Changes in v2:
- Addressed checkpatch alignment/line length warnings.
- Removed superfluous init in qcom_snps_hsphy_resume().

 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 100 ++++++++++++++++++++++++++
 1 file changed, 100 insertions(+)
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4 -0
index 4d74045..0a4e77af 100644
@@ -76,7 +76,9 @@
  * @iface_clk: phy interface clock
  * @phy_reset: phy reset control
  * @vregs: regulator supplies bulk data
+ * @suspended: PHY is in the suspended state
  * @phy_initialized: if PHY has been initialized correctly
+ * @mode: contains the current mode the PHY is in
  */
 struct qcom_snps_hsphy {
 	struct phy *phy;
@@ -87,7 +89,9 @@ struct qcom_snps_hsphy {
 	struct reset_control *phy_reset;
 	struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS];
 
+	bool suspended;
 	bool phy_initialized;
+	enum phy_mode mode;
 };
 
 static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 114

Quoted 7 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4 -0
@@ -104,6 +108,84 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
 	readl_relaxed(base + offset);
 }
 
+static int qcom_snps_hsphy_suspend(struct qcom_snps_hsphy *hsphy)
+{
+	if (hsphy->suspended)
+		return 0;

Am still not convinced why this would be called when we are already suspended :)

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 117

Quoted 3 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +3 -0
+
+	dev_dbg(&hsphy->phy->dev, "Suspend QCOM SNPS PHY, mode:%d\n",
+		hsphy->mode);

Remove debug artifacts here?

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 124

Quoted 7 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +7 -0
+
+	if (hsphy->mode == PHY_MODE_USB_HOST) {
+		/* Enable auto-resume to meet remote wakeup timing */
+		qcom_snps_hsphy_write_mask(hsphy->base,
+						USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+						USB2_AUTO_RESUME,
+						USB2_AUTO_RESUME);

Lets align the lines above to opening brace please..
If you run checkpatch with --strict option you would get this CHECK: Alignment should match open parenthesis

Quoted 11 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +11 -0
+		usleep_range(500, 1000);
+		qcom_snps_hsphy_write_mask(hsphy->base,
+						USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+						0, USB2_AUTO_RESUME);
+	}
+
+	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+	hsphy->suspended = true;
+
+	return 0;
+}

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 145

Quoted 10 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +10 -0
+
+static int qcom_snps_hsphy_resume(struct qcom_snps_hsphy *hsphy)
+{
+	int ret;
+
+	if (!hsphy->suspended)
+		return 0;
+
+	dev_dbg(&hsphy->phy->dev, "Resume QCOM SNPS PHY, mode:%d\n",
+		hsphy->mode);

here as well

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 150

Quoted 5 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +5 -0
+
+	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
+	if (ret) {
+		dev_err(&hsphy->phy->dev,
+			"failed to enable cfg ahb clock, %d\n", ret);

single line should be okay now :)

Quoted 50 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +39 -0
+		return ret;
+	}
+
+	hsphy->suspended = false;
+	return 0;
+}
+
+static int __maybe_unused qcom_snps_hsphy_runtime_suspend(struct device *dev)
+{
+	struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
+
+	if (!hsphy->phy_initialized)
+		return 0;
+
+	qcom_snps_hsphy_suspend(hsphy);
+	return 0;
+}
+
+static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
+{
+	struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
+
+	if (!hsphy->phy_initialized)
+		return 0;
+
+	qcom_snps_hsphy_resume(hsphy);
+	return 0;
+}
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
+					int submode)
+{
+	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
+
+	hsphy->mode = mode;
+	return 0;
+}
+
 static int qcom_snps_hsphy_init(struct phy *phy)
 {
 	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
@@ -175,6 +257,7 @@ static int qcom_snps_hsphy_init(struct phy *phy)
 					UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0);
 
 	hsphy->phy_initialized = true;
+	hsphy->suspended = false;
 
 	return 0;
 

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static int qcom_snps_hsphy_exit(struct phy *phy) · line 287

Quoted 4 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +1 -0
@@ -201,6 +284,7 @@ static int qcom_snps_hsphy_exit(struct phy *phy)
 static const struct phy_ops qcom_snps_hsphy_gen_ops = {
 	.init		= qcom_snps_hsphy_init,
 	.exit		= qcom_snps_hsphy_exit,
+	.set_mode	= qcom_snps_hsphy_set_mode,

This should be a separate patch, whats set_mode got to do with suspend support :)

Quoted 50 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +16 -0
 	.owner		= THIS_MODULE,
 };
 
@@ -212,6 +296,11 @@ static int qcom_snps_hsphy_exit(struct phy *phy)
 };
 MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_of_match_table);
 
+static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
+	SET_RUNTIME_PM_OPS(qcom_snps_hsphy_runtime_suspend,
+			   qcom_snps_hsphy_runtime_resume, NULL)
+};
+
 static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -255,6 +344,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Prevent runtime pm from being ON by default. Users can enable
+	 * it using power/control in sysfs.
+	 */
+	pm_runtime_forbid(dev);
+
 	generic_phy = devm_phy_create(dev, NULL, &qcom_snps_hsphy_gen_ops);
 	if (IS_ERR(generic_phy)) {
 		ret = PTR_ERR(generic_phy);
@@ -269,6 +366,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 	if (!IS_ERR(phy_provider))
 		dev_dbg(dev, "Registered Qcom-SNPS HS phy\n");
+	else
+		pm_runtime_disable(dev);
 
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
@@ -277,6 +376,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 	.probe		= qcom_snps_hsphy_probe,
 	.driver = {
 		.name	= "qcom-snps-hs-femto-v2-phy",
+		.pm = &qcom_snps_hsphy_pm_ops,
 		.of_match_table = qcom_snps_hsphy_of_match_table,
 	},
 };
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 1 line
~Vinod
#2 lore raw
Quoted 45 lines · Vinod Koul

Hi Wesley,

Quoted 42 lines · Wesley Cheng

Allow for the PHY to be put into a powered down state when possible. Add the required suspend and resume callbacks, which will determine what resources can be turned off depending on the cable status.

---
Changes in v2:
- Addressed checkpatch alignment/line length warnings.
- Removed superfluous init in qcom_snps_hsphy_resume().

 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 100 ++++++++++++++++++++++++++
 1 file changed, 100 insertions(+)
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4 -0
index 4d74045..0a4e77af 100644
@@ -76,7 +76,9 @@
  * @iface_clk: phy interface clock
  * @phy_reset: phy reset control
  * @vregs: regulator supplies bulk data
+ * @suspended: PHY is in the suspended state
  * @phy_initialized: if PHY has been initialized correctly
+ * @mode: contains the current mode the PHY is in
  */
 struct qcom_snps_hsphy {
 	struct phy *phy;
@@ -87,7 +89,9 @@ struct qcom_snps_hsphy {
 	struct reset_control *phy_reset;
 	struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS];
 
+	bool suspended;
 	bool phy_initialized;
+	enum phy_mode mode;
 };
 
 static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
@@ -104,6 +108,84 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
 	readl_relaxed(base + offset);
 }
 
Quoted 8 lines

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 114

Quoted 4 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4 -0
+static int qcom_snps_hsphy_suspend(struct qcom_snps_hsphy *hsphy)
+{
+	if (hsphy->suspended)
+		return 0;

Am still not convinced why this would be called when we are already suspended :)

Hi Vinod,

OK, we can remove it for now, and if its really required further on, we can re-add.

Quoted 6 lines

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 117

Quoted 3 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +3 -0
+
+	dev_dbg(&hsphy->phy->dev, "Suspend QCOM SNPS PHY, mode:%d\n",
+		hsphy->mode);

Remove debug artifacts here?

Sure, can do that.

Quoted 11 lines

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 124

Quoted 7 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +7 -0
+
+	if (hsphy->mode == PHY_MODE_USB_HOST) {
+		/* Enable auto-resume to meet remote wakeup timing */
+		qcom_snps_hsphy_write_mask(hsphy->base,
+						USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+						USB2_AUTO_RESUME,
+						USB2_AUTO_RESUME);

Lets align the lines above to opening brace please..
If you run checkpatch with --strict option you would get this CHECK: Alignment should match open parenthesis

OK, got it. Fixed a few other spacing warnings as well.

Quoted 15 lines
Quoted 15 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +15 -0
+		usleep_range(500, 1000);
+		qcom_snps_hsphy_write_mask(hsphy->base,
+						USB2_PHY_USB_PHY_HS_PHY_CTRL2,
+						0, USB2_AUTO_RESUME);
+	}
+
+	clk_disable_unprepare(hsphy->cfg_ahb_clk);
+	hsphy->suspended = true;
+
+	return 0;
+}
+
+static int qcom_snps_hsphy_resume(struct qcom_snps_hsphy *hsphy)
+{
+	int ret;
Quoted 9 lines

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 145

Quoted 6 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +6 -0
+
+	if (!hsphy->suspended)
+		return 0;
+
+	dev_dbg(&hsphy->phy->dev, "Resume QCOM SNPS PHY, mode:%d\n",
+		hsphy->mode);

here as well

Done.

Quoted 8 lines

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 150

Quoted 5 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +5 -0
+
+	ret = clk_prepare_enable(hsphy->cfg_ahb_clk);
+	if (ret) {
+		dev_err(&hsphy->phy->dev,
+			"failed to enable cfg ahb clock, %d\n", ret);

single line should be okay now :)

Yep!

Quoted 49 lines
Quoted 49 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +39 -0
+		return ret;
+	}
+
+	hsphy->suspended = false;
+	return 0;
+}
+
+static int __maybe_unused qcom_snps_hsphy_runtime_suspend(struct device *dev)
+{
+	struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
+
+	if (!hsphy->phy_initialized)
+		return 0;
+
+	qcom_snps_hsphy_suspend(hsphy);
+	return 0;
+}
+
+static int __maybe_unused qcom_snps_hsphy_runtime_resume(struct device *dev)
+{
+	struct qcom_snps_hsphy *hsphy = dev_get_drvdata(dev);
+
+	if (!hsphy->phy_initialized)
+		return 0;
+
+	qcom_snps_hsphy_resume(hsphy);
+	return 0;
+}
+
+static int qcom_snps_hsphy_set_mode(struct phy *phy, enum phy_mode mode,
+					int submode)
+{
+	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
+
+	hsphy->mode = mode;
+	return 0;
+}
+
 static int qcom_snps_hsphy_init(struct phy *phy)
 {
 	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
@@ -175,6 +257,7 @@ static int qcom_snps_hsphy_init(struct phy *phy)
 					UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0);
 
 	hsphy->phy_initialized = true;
+	hsphy->suspended = false;
 
 	return 0;
 
Quoted 9 lines

drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static int qcom_snps_hsphy_exit(struct phy *phy) · line 287

Quoted 5 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +1 -0
@@ -201,6 +284,7 @@ static int qcom_snps_hsphy_exit(struct phy *phy)
 static const struct phy_ops qcom_snps_hsphy_gen_ops = {
 	.init		= qcom_snps_hsphy_init,
 	.exit		= qcom_snps_hsphy_exit,
+	.set_mode	= qcom_snps_hsphy_set_mode,

This should be a separate patch, whats set_mode got to do with suspend support :)

Got it, will split this into another patch

Quoted 51 lines
Quoted 50 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +16 -0
 	.owner		= THIS_MODULE,
 };
 
@@ -212,6 +296,11 @@ static int qcom_snps_hsphy_exit(struct phy *phy)
 };
 MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_of_match_table);
 
+static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = {
+	SET_RUNTIME_PM_OPS(qcom_snps_hsphy_runtime_suspend,
+			   qcom_snps_hsphy_runtime_resume, NULL)
+};
+
 static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -255,6 +344,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 		return ret;
 	}
 
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Prevent runtime pm from being ON by default. Users can enable
+	 * it using power/control in sysfs.
+	 */
+	pm_runtime_forbid(dev);
+
 	generic_phy = devm_phy_create(dev, NULL, &qcom_snps_hsphy_gen_ops);
 	if (IS_ERR(generic_phy)) {
 		ret = PTR_ERR(generic_phy);
@@ -269,6 +366,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 	if (!IS_ERR(phy_provider))
 		dev_dbg(dev, "Registered Qcom-SNPS HS phy\n");
+	else
+		pm_runtime_disable(dev);
 
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
@@ -277,6 +376,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)
 	.probe		= qcom_snps_hsphy_probe,
 	.driver = {
 		.name	= "qcom-snps-hs-femto-v2-phy",
+		.pm = &qcom_snps_hsphy_pm_ops,
 		.of_match_table = qcom_snps_hsphy_of_match_table,
 	},
 };
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project