phy: qcom-snps: Add runtime suspend and resume handlers
Subsystems (2)
PATCH v2 1/1 phy: qcom-snps: Add runtime suspend and resume handlers
Allow for the PHY to be put into a powered down state when possible. Add the required suspend and resume callbacks, which will determine what resources can be turned off depending on the cable status.
---
Changes in v2:
- Addressed checkpatch alignment/line length warnings.
- Removed superfluous init in qcom_snps_hsphy_resume().
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 100 ++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +100 -0
@@ -76,7 +76,9 @@* @iface_clk: phy interface clock * @phy_reset: phy reset control * @vregs: regulator supplies bulk data +* @suspended: PHY is in the suspended state * @phy_initialized: if PHY has been initialized correctly +* @mode: contains the current mode the PHY is in */ struct qcom_snps_hsphy {struct phy *phy;
@@ -87,7 +89,9 @@ struct qcom_snps_hsphy {struct reset_control *phy_reset;struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS ]; +bool suspended;bool phy_initialized; +enum phy_mode mode; }; static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
@@ -104,6 +108,84 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,readl_relaxed (base + offset); } +static int qcom_snps_hsphy_suspend (struct qcom_snps_hsphy *hsphy) +{ +if (hsphy->suspended) +return 0 ; + +dev_dbg (&hsphy->phy->dev,"Suspend QCOM SNPS PHY, mode:%d\n" , + hsphy->mode); + +if (hsphy->mode ==PHY_MODE_USB_HOST ) { +/* Enable auto-resume to meet remote wakeup timing */ +qcom_snps_hsphy_write_mask (hsphy->base, +USB2_PHY_USB_PHY_HS_PHY_CTRL2 , +USB2_AUTO_RESUME , +USB2_AUTO_RESUME ); +usleep_range (500 ,1000 ); +qcom_snps_hsphy_write_mask (hsphy->base, +USB2_PHY_USB_PHY_HS_PHY_CTRL2 , +0 ,USB2_AUTO_RESUME ); + } + +clk_disable_unprepare (hsphy->cfg_ahb_clk); + hsphy->suspended = true; + +return 0 ; +} + +static int qcom_snps_hsphy_resume (struct qcom_snps_hsphy *hsphy) +{ +int ret; + +if (!hsphy->suspended) +return 0 ; + +dev_dbg (&hsphy->phy->dev,"Resume QCOM SNPS PHY, mode:%d\n" , + hsphy->mode); + + ret =clk_prepare_enable (hsphy->cfg_ahb_clk); +if (ret) { +dev_err (&hsphy->phy->dev, +"failed to enable cfg ahb clock, %d\n" , ret); +return ret; + } + + hsphy->suspended = false; +return 0 ; +} + +static int __maybe_unused qcom_snps_hsphy_runtime_suspend (struct device *dev) +{ +struct qcom_snps_hsphy *hsphy =dev_get_drvdata (dev); + +if (!hsphy->phy_initialized) +return 0 ; + +qcom_snps_hsphy_suspend (hsphy); +return 0 ; +} + +static int __maybe_unused qcom_snps_hsphy_runtime_resume (struct device *dev) +{ +struct qcom_snps_hsphy *hsphy =dev_get_drvdata (dev); + +if (!hsphy->phy_initialized) +return 0 ; + +qcom_snps_hsphy_resume (hsphy); +return 0 ; +} + +static int qcom_snps_hsphy_set_mode (struct phy *phy,enum phy_mode mode, +int submode) +{ +struct qcom_snps_hsphy *hsphy =phy_get_drvdata (phy); + + hsphy->mode = mode; +return 0 ; +} +static int qcom_snps_hsphy_init (struct phy *phy) {struct qcom_snps_hsphy *hsphy =phy_get_drvdata (phy);
@@ -175,6 +257,7 @@ static int qcom_snps_hsphy_init(struct phy *phy) UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0); hsphy->phy_initialized = true; + hsphy->suspended = false;return 0 ;
@@ -201,6 +284,7 @@ static int qcom_snps_hsphy_exit(struct phy *phy)static const struct phy_ops qcom_snps_hsphy_gen_ops = { .init = qcom_snps_hsphy_init, .exit = qcom_snps_hsphy_exit, + .set_mode = qcom_snps_hsphy_set_mode, .owner =THIS_MODULE , };
@@ -212,6 +296,11 @@ static int qcom_snps_hsphy_exit(struct phy *phy) };MODULE_DEVICE_TABLE (of, qcom_snps_hsphy_of_match_table); +static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = { +SET_RUNTIME_PM_OPS (qcom_snps_hsphy_runtime_suspend, + qcom_snps_hsphy_runtime_resume,NULL ) +}; +static int qcom_snps_hsphy_probe (struct platform_device *pdev) {struct device *dev = &pdev->dev;
@@ -255,6 +344,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)return ret; } +pm_runtime_set_active (dev); +pm_runtime_enable (dev); +/* +* Prevent runtime pm from being ON by default. Users can enable +* it using power/control in sysfs. +*/ +pm_runtime_forbid (dev); + generic_phy =devm_phy_create (dev,NULL , &qcom_snps_hsphy_gen_ops);if (IS_ERR (generic_phy)) { ret =PTR_ERR (generic_phy);
@@ -269,6 +366,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) phy_provider =devm_of_phy_provider_register (dev, of_phy_simple_xlate);if (!IS_ERR (phy_provider))dev_dbg (dev,"Registered Qcom-SNPS HS phy\n" ); +else +pm_runtime_disable (dev);return PTR_ERR_OR_ZERO (phy_provider); }
@@ -277,6 +376,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) .probe = qcom_snps_hsphy_probe, .driver = { .name = "qcom-snps-hs-femto-v2-phy", + .pm = &qcom_snps_hsphy_pm_ops, .of_match_table = qcom_snps_hsphy_of_match_table, }, };
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Vinod Koul
maintainerHi Wesley,
Quoted 39 lines · Wesley Cheng
Allow for the PHY to be put into a powered down state when possible. Add the required suspend and resume callbacks, which will determine what resources can be turned off depending on the cable status.
Signed-off-by Wesley Cheng <[email protected]>---
Changes in v2:
- Addressed checkpatch alignment/line length warnings.
- Removed superfluous init inqcom_snps_hsphy_resume().drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 100 ++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4
-0@@ -76,7 +76,9 @@* @iface_clk: phy interface clock * @phy_reset: phy reset control * @vregs: regulator supplies bulk data +* @suspended: PHY is in the suspended state * @phy_initialized: if PHY has been initialized correctly +* @mode: contains the current mode the PHY is in */ struct qcom_snps_hsphy {struct phy *phy;@@ -87,7 +89,9 @@ struct qcom_snps_hsphy {struct reset_control *phy_reset;struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS ]; +bool suspended;bool phy_initialized; +enum phy_mode mode; }; static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 114
Quoted 7 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4
-0@@ -104,6 +108,84 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,readl_relaxed (base + offset); } +static int qcom_snps_hsphy_suspend (struct qcom_snps_hsphy *hsphy) +{ +if (hsphy->suspended) +return 0 ;
Am still not convinced why this would be called when we are already suspended :)
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 117
Quoted 3 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +3
-0+ +dev_dbg (&hsphy->phy->dev,"Suspend QCOM SNPS PHY, mode:%d\n" , + hsphy->mode);
Remove debug artifacts here?
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 124
Quoted 7 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +7
-0+ +if (hsphy->mode ==PHY_MODE_USB_HOST ) { +/* Enable auto-resume to meet remote wakeup timing */ +qcom_snps_hsphy_write_mask (hsphy->base, +USB2_PHY_USB_PHY_HS_PHY_CTRL2 , +USB2_AUTO_RESUME , +USB2_AUTO_RESUME );
Lets align the lines above to opening brace please..
If you run checkpatch with --strict option you would get this CHECK: Alignment should match open parenthesis
Quoted 11 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +11
-0+usleep_range (500 ,1000 ); +qcom_snps_hsphy_write_mask (hsphy->base, +USB2_PHY_USB_PHY_HS_PHY_CTRL2 , +0 ,USB2_AUTO_RESUME ); + } + +clk_disable_unprepare (hsphy->cfg_ahb_clk); + hsphy->suspended = true; + +return 0 ; +}
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 145
Quoted 10 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +10
-0+ +static int qcom_snps_hsphy_resume (struct qcom_snps_hsphy *hsphy) +{ +int ret; + +if (!hsphy->suspended) +return 0 ; + +dev_dbg (&hsphy->phy->dev,"Resume QCOM SNPS PHY, mode:%d\n" , + hsphy->mode);
here as well
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 150
Quoted 5 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +5
-0+ + ret =clk_prepare_enable (hsphy->cfg_ahb_clk); +if (ret) { +dev_err (&hsphy->phy->dev, +"failed to enable cfg ahb clock, %d\n" , ret);
single line should be okay now :)
Quoted 50 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +39
-0+return ret; + } + + hsphy->suspended = false; +return 0 ; +} + +static int __maybe_unused qcom_snps_hsphy_runtime_suspend (struct device *dev) +{ +struct qcom_snps_hsphy *hsphy =dev_get_drvdata (dev); + +if (!hsphy->phy_initialized) +return 0 ; + +qcom_snps_hsphy_suspend (hsphy); +return 0 ; +} + +static int __maybe_unused qcom_snps_hsphy_runtime_resume (struct device *dev) +{ +struct qcom_snps_hsphy *hsphy =dev_get_drvdata (dev); + +if (!hsphy->phy_initialized) +return 0 ; + +qcom_snps_hsphy_resume (hsphy); +return 0 ; +} + +static int qcom_snps_hsphy_set_mode (struct phy *phy,enum phy_mode mode, +int submode) +{ +struct qcom_snps_hsphy *hsphy =phy_get_drvdata (phy); + + hsphy->mode = mode; +return 0 ; +} +static int qcom_snps_hsphy_init (struct phy *phy) {struct qcom_snps_hsphy *hsphy =phy_get_drvdata (phy);@@ -175,6 +257,7 @@ static int qcom_snps_hsphy_init(struct phy *phy) UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0); hsphy->phy_initialized = true; + hsphy->suspended = false;return 0 ;
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static int qcom_snps_hsphy_exit(struct phy *phy) · line 287
Quoted 4 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +1
-0@@ -201,6 +284,7 @@ static int qcom_snps_hsphy_exit(struct phy *phy)static const struct phy_ops qcom_snps_hsphy_gen_ops = { .init = qcom_snps_hsphy_init, .exit = qcom_snps_hsphy_exit, + .set_mode = qcom_snps_hsphy_set_mode,
This should be a separate patch, whats set_mode got to do with suspend support :)
Quoted 50 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +16
-0.owner = THIS_MODULE, };@@ -212,6 +296,11 @@ static int qcom_snps_hsphy_exit(struct phy *phy) };MODULE_DEVICE_TABLE (of, qcom_snps_hsphy_of_match_table); +static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = { +SET_RUNTIME_PM_OPS (qcom_snps_hsphy_runtime_suspend, + qcom_snps_hsphy_runtime_resume,NULL ) +}; +static int qcom_snps_hsphy_probe (struct platform_device *pdev) {struct device *dev = &pdev->dev;@@ -255,6 +344,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)return ret; } +pm_runtime_set_active (dev); +pm_runtime_enable (dev); +/* +* Prevent runtime pm from being ON by default. Users can enable +* it using power/control in sysfs. +*/ +pm_runtime_forbid (dev); + generic_phy =devm_phy_create (dev,NULL , &qcom_snps_hsphy_gen_ops);if (IS_ERR (generic_phy)) { ret =PTR_ERR (generic_phy);@@ -269,6 +366,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) phy_provider =devm_of_phy_provider_register (dev, of_phy_simple_xlate);if (!IS_ERR (phy_provider))dev_dbg (dev,"Registered Qcom-SNPS HS phy\n" ); +else +pm_runtime_disable (dev);return PTR_ERR_OR_ZERO (phy_provider); }@@ -277,6 +376,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) .probe = qcom_snps_hsphy_probe, .driver = { .name = "qcom-snps-hs-femto-v2-phy", + .pm = &qcom_snps_hsphy_pm_ops, .of_match_table = qcom_snps_hsphy_of_match_table, }, };Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Signature · 1 line
~Vinod
Quoted 45 lines · Vinod Koul
Hi Wesley,
Quoted 42 lines · Wesley Cheng
Allow for the PHY to be put into a powered down state when possible. Add the required suspend and resume callbacks, which will determine what resources can be turned off depending on the cable status.
Signed-off-by Wesley Cheng <[email protected]>---
Changes in v2:
- Addressed checkpatch alignment/line length warnings.
- Removed superfluous init inqcom_snps_hsphy_resume().drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 100 ++++++++++++++++++++++++++ 1 file changed, 100 insertions(+)drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4
-0@@ -76,7 +76,9 @@* @iface_clk: phy interface clock * @phy_reset: phy reset control * @vregs: regulator supplies bulk data +* @suspended: PHY is in the suspended state * @phy_initialized: if PHY has been initialized correctly +* @mode: contains the current mode the PHY is in */ struct qcom_snps_hsphy {struct phy *phy;@@ -87,7 +89,9 @@ struct qcom_snps_hsphy {struct reset_control *phy_reset;struct regulator_bulk_data vregs[SNPS_HS_NUM_VREGS ]; +bool suspended;bool phy_initialized; +enum phy_mode mode; }; static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,@@ -104,6 +108,84 @@ static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset,readl_relaxed (base + offset); }
Quoted 8 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 114
Quoted 4 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +4
-0+static int qcom_snps_hsphy_suspend (struct qcom_snps_hsphy *hsphy) +{ +if (hsphy->suspended) +return 0 ;Am still not convinced why this would be called when we are already suspended :)
Hi Vinod,
OK, we can remove it for now, and if its really required further on, we can re-add.
Quoted 6 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 117
Quoted 3 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +3
-0+ +dev_dbg (&hsphy->phy->dev,"Suspend QCOM SNPS PHY, mode:%d\n" , + hsphy->mode);Remove debug artifacts here?
Sure, can do that.
Quoted 11 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 124
Quoted 7 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +7
-0+ +if (hsphy->mode ==PHY_MODE_USB_HOST ) { +/* Enable auto-resume to meet remote wakeup timing */ +qcom_snps_hsphy_write_mask (hsphy->base, +USB2_PHY_USB_PHY_HS_PHY_CTRL2 , +USB2_AUTO_RESUME , +USB2_AUTO_RESUME );Lets align the lines above to opening brace please..
If you run checkpatch with --strict option you would get this CHECK: Alignment should match open parenthesis
OK, got it. Fixed a few other spacing warnings as well.
Quoted 15 lines
Quoted 15 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +15
-0+usleep_range (500 ,1000 ); +qcom_snps_hsphy_write_mask (hsphy->base, +USB2_PHY_USB_PHY_HS_PHY_CTRL2 , +0 ,USB2_AUTO_RESUME ); + } + +clk_disable_unprepare (hsphy->cfg_ahb_clk); + hsphy->suspended = true; + +return 0 ; +} + +static int qcom_snps_hsphy_resume (struct qcom_snps_hsphy *hsphy) +{ +int ret;
Quoted 9 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 145
Quoted 6 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +6
-0+ +if (!hsphy->suspended) +return 0 ; + +dev_dbg (&hsphy->phy->dev,"Resume QCOM SNPS PHY, mode:%d\n" , + hsphy->mode);here as well
Done.
Quoted 8 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static inline void qcom_snps_hsphy_write_mask(void __iomem *base, u32 offset, · line 150
Quoted 5 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +5
-0+ + ret =clk_prepare_enable (hsphy->cfg_ahb_clk); +if (ret) { +dev_err (&hsphy->phy->dev, +"failed to enable cfg ahb clock, %d\n" , ret);single line should be okay now :)
Yep!
Quoted 49 lines
Quoted 49 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +39
-0+return ret; + } + + hsphy->suspended = false; +return 0 ; +} + +static int __maybe_unused qcom_snps_hsphy_runtime_suspend (struct device *dev) +{ +struct qcom_snps_hsphy *hsphy =dev_get_drvdata (dev); + +if (!hsphy->phy_initialized) +return 0 ; + +qcom_snps_hsphy_suspend (hsphy); +return 0 ; +} + +static int __maybe_unused qcom_snps_hsphy_runtime_resume (struct device *dev) +{ +struct qcom_snps_hsphy *hsphy =dev_get_drvdata (dev); + +if (!hsphy->phy_initialized) +return 0 ; + +qcom_snps_hsphy_resume (hsphy); +return 0 ; +} + +static int qcom_snps_hsphy_set_mode (struct phy *phy,enum phy_mode mode, +int submode) +{ +struct qcom_snps_hsphy *hsphy =phy_get_drvdata (phy); + + hsphy->mode = mode; +return 0 ; +} +static int qcom_snps_hsphy_init (struct phy *phy) {struct qcom_snps_hsphy *hsphy =phy_get_drvdata (phy);@@ -175,6 +257,7 @@ static int qcom_snps_hsphy_init(struct phy *phy) UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0); hsphy->phy_initialized = true; + hsphy->suspended = false;return 0 ;
Quoted 9 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c static int qcom_snps_hsphy_exit(struct phy *phy) · line 287
Quoted 5 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +1
-0@@ -201,6 +284,7 @@ static int qcom_snps_hsphy_exit(struct phy *phy)static const struct phy_ops qcom_snps_hsphy_gen_ops = { .init = qcom_snps_hsphy_init, .exit = qcom_snps_hsphy_exit, + .set_mode = qcom_snps_hsphy_set_mode,This should be a separate patch, whats
set_modegot to do with suspend support :)
Got it, will split this into another patch
Quoted 51 lines
Quoted 50 lines
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c +16
-0.owner = THIS_MODULE, };@@ -212,6 +296,11 @@ static int qcom_snps_hsphy_exit(struct phy *phy) };MODULE_DEVICE_TABLE (of, qcom_snps_hsphy_of_match_table); +static const struct dev_pm_ops qcom_snps_hsphy_pm_ops = { +SET_RUNTIME_PM_OPS (qcom_snps_hsphy_runtime_suspend, + qcom_snps_hsphy_runtime_resume,NULL ) +}; +static int qcom_snps_hsphy_probe (struct platform_device *pdev) {struct device *dev = &pdev->dev;@@ -255,6 +344,14 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev)return ret; } +pm_runtime_set_active (dev); +pm_runtime_enable (dev); +/* +* Prevent runtime pm from being ON by default. Users can enable +* it using power/control in sysfs. +*/ +pm_runtime_forbid (dev); + generic_phy =devm_phy_create (dev,NULL , &qcom_snps_hsphy_gen_ops);if (IS_ERR (generic_phy)) { ret =PTR_ERR (generic_phy);@@ -269,6 +366,8 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) phy_provider =devm_of_phy_provider_register (dev, of_phy_simple_xlate);if (!IS_ERR (phy_provider))dev_dbg (dev,"Registered Qcom-SNPS HS phy\n" ); +else +pm_runtime_disable (dev);return PTR_ERR_OR_ZERO (phy_provider); }@@ -277,6 +376,7 @@ static int qcom_snps_hsphy_probe(struct platform_device *pdev) .probe = qcom_snps_hsphy_probe, .driver = { .name = "qcom-snps-hs-femto-v2-phy", + .pm = &qcom_snps_hsphy_pm_ops, .of_match_table = qcom_snps_hsphy_of_match_table, }, };Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project