Skip to contentSkip to conversation

WPA2, compat-wireless-2.6.31-rc3, kernel 2.6.28 - rtl8187 - association works but no ping

DISCUSSION Ivan Kuten 2 participants 7 messages Jul 23, 2009 – Jul 24, 2009

lore
Share & tools
lore

Ivan Kuten

author
#0 lore raw

Hello,

I'm testing rtl8187 on Blackfin platform (linux-2.6.28) compat-wireless-2.6.31-rc3
driver rtl8187
wpa_supplicant-0.6.5

Sympthoms:
Association works but no ping in WPA2(AES) Association works and ping is working with WPA(TKIP)

This is probably not a wpa_supplicant and it's config problem
because it's working (WPA2-AES and WPA-TKIP) on 2.6.28 with corresponding configs.

Any suggestions how to track down the problem?

Best regards,
Ivan

#1 lore raw
Quoted 1 line · Ivan Kuten

compat-wireless-2.6.31-rc3

compat-wireless-2.6.31-rc4 is out, please try that.

Luis

author
#2 lore raw
Quoted 7 lines · Ivan Kuten
Quoted 1 line

compat-wireless-2.6.31-rc3

compat-wireless-2.6.31-rc4 is out, please try that.

Luis

Here is what I get for compat-wireless-2.6.31-rc4:

<6>cfg80211: Using static regulatory domain info
<6>cfg80211: Regulatory domain: US

<6>     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>     (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
<6>     (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6>     (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6>     (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6>     (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
<6>     (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)

<6>usb 1-1: new high speed USB device using isp1761 and address 2 <6>cfg80211: Calling CRDA for country: US
<6>usbcore: registered new interface driver rtl8187 <6>usb 1-1: configuration #1 chosen from 1 choice
<6>hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 3 ports detected
<6>usb 1-1.1: new high speed USB device using isp1761 and address 3 <6>usb 1-1.1: configuration #1 chosen from 1 choice <7>phy0: Selected rate control algorithm 'minstrel' <6>phy0: hwaddr 00277080, RTL8187vB (default) V1 + rtl8225z2 <7>phy0: device now idle
<7>phy0: device no longer idle - scanning
<7>phy0: device now idle
<7>phy0: device no longer idle - in use
<7>wlan0: authenticate with AP 01a4b568
<7>wlan0: authenticated
<7>wlan0: associate with AP 01a4b568
<7>wlan0: RX AssocResp from 003e101a (capab=0x411 status=0 aid=2) <7>wlan0: associated
<7>phy0: Allocated STA 002fbfc4
<7>phy0: Inserted STA 002fbfc4
<7>wlan0: switched to short slot time (BSSID=01a4b568)

iwconfig output:

lo no wireless extensions.

eth0 no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11bg ESSID:"ACORP"
Mode:Managed Frequency:2.462 GHz Access Point: 00:02:72:74:AC:85
Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:2BAC-63B9-5D99-CF9A-4D39-079F-BB55-5D39 [2] Power Management:off
Link Quality=61/70 Signal level=-49 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

ifconfig:

eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:188 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)

wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)

wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

Neither dhcp nor setting static IP for wlan0 - no ping.

Regards,
Ivan

#3 lore raw
Quoted 34 lines · Ivan Kuten
Quoted 7 lines · Ivan Kuten
Quoted 1 line

compat-wireless-2.6.31-rc3

compat-wireless-2.6.31-rc4 is out, please try that.

  Luis

Here is what I get for compat-wireless-2.6.31-rc4:

<6>cfg80211: Using static regulatory domain info
<6>cfg80211: Regulatory domain: US
<6>     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) <6>     (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) <6>     (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6>     (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6>     (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6>     (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6>     (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) <6>usb 1-1: new high speed USB device using isp1761 and address 2 <6>cfg80211: Calling CRDA for country: US
<6>usbcore: registered new interface driver rtl8187
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 3 ports detected
<6>usb 1-1.1: new high speed USB device using isp1761 and address 3 <6>usb 1-1.1: configuration #1 chosen from 1 choice
<7>phy0: Selected rate control algorithm 'minstrel'
<6>phy0: hwaddr 00277080, RTL8187vB (default) V1 + rtl8225z2 <7>phy0: device now idle
<7>phy0: device no longer idle - scanning
<7>phy0: device now idle
<7>phy0: device no longer idle - in use

Quoted 8 lines

<7>wlan0: authenticate with AP 01a4b568
<7>wlan0: authenticated
<7>wlan0: associate with AP 01a4b568
<7>wlan0: RX AssocResp from 003e101a (capab=0x411 status=0 aid=2) <7>wlan0: associated
<7>phy0: Allocated STA 002fbfc4
<7>phy0: Inserted STA 002fbfc4
<7>wlan0: switched to short slot time (BSSID=01a4b568)

This looks peachy.

Quoted 21 lines

iwconfig output:

lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11bg  ESSID:"ACORP"
         Mode:Managed  Frequency:2.462 GHz  Access Point: 00:02:72:74:AC:85 Bit Rate=1 Mb/s   Tx-Power=27 dBm
         Retry  long limit:7   RTS thr:off   Fragment thr:off Encryption key:2BAC-63B9-5D99-CF9A-4D39-079F-BB55-5D39 [2] Power Management:off
         Link Quality=61/70  Signal level=-49 dBm
         Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 Tx excessive retries:0  Invalid misc:0   Missed beacon:0

ifconfig:

Quoted 7 lines

eth0      Link encap:Ethernet  HWaddr 02:80:AD:20:31:EB
         inet addr:192.168.5.1  Bcast:192.168.5.255  Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:188 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
         RX bytes:4077 (3.9 KiB)  TX bytes:17012 (16.6 KiB)

Note an IP address on eth0, most likely you have a default route using eht0 as well. Check with 'ip route'.

Quoted 7 lines

wlan0     Link encap:Ethernet  HWaddr 00:12:0E:98:67:FC UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
         RX bytes:304 (304.0 B)  TX bytes:3932 (3.8 KiB)

Quoted 8 lines

wmaster0  Link encap:UNSPEC  HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00 UP RUNNING  MTU:0  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

Neither dhcp nor setting static IP for wlan0 - no ping.

Do you have Network Manager on? Please read:

http://wireless.kernel.org/en/users/Documentation/Reporting_bugs

Specifically the section that describes getting 'iw event -t' log and Network Manager.

Luis

author
#4 lore raw
Quoted 10 lines
Quoted 9 lines

ifconfig:

eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:188 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)

Quoted 3 lines

Note an IP address on eth0, most likely you have a default route using eht0 as well. Check with 'ip route'.

No default route. eth0 only for netconsole.
I'm doing udhcpc on wlan0.
Another thing is that WPA-TKIP is working. The problem only with CCMP. I posted also in wpa_supplicant list with detailed wpa_supplicant log:
http://lists.shmoo.com/pipermail/hostap/2009-July/020026.html

Quoted 14 lines
Quoted 14 lines

wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)

wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

Quoted 4 lines
Quoted 1 line

Neither dhcp nor setting static IP for wlan0 - no ping.

Do you have Network Manager on? Please read:

No Network Manager.
Just:
wpa_supplicant -Dwext -iwlan0 -c /home/ACORP.conf -dd & /sbin/udhcpc -n -q -i wlan0 -s /bin/default.script

Quoted 5 lines

http://wireless.kernel.org/en/users/Documentation/Reporting_bugs

Specifically the section that describes getting 'iw event -t' log and Network Manager.

I'll try with iw event -t.
Is it possible to check via debugfs something like number of received unencrypted packets?

Regards,
Ivan

#5 lore raw
Quoted 4 lines · Ivan Kuten

No Network Manager.
Just:
wpa_supplicant -Dwext -iwlan0 -c /home/ACORP.conf -dd & /sbin/udhcpc -n -q -i wlan0 -s /bin/default.script

How did you get the eth0 IP? ps -ef?

Luis

author
#6 lore raw
Quoted 6 lines · Ivan Kuten
Quoted 4 lines

No Network Manager.
Just:
wpa_supplicant -Dwext -iwlan0 -c /home/ACORP.conf -dd & /sbin/udhcpc -n -q -i wlan0 -s /bin/default.script

Quoted 6 lines

How did you get the eth0 IP? ps -ef?

Luis

in rc script it's ifconfig eth0 192.168.5.1
it's the same behaviour without eth0. I'm using eth0 for netconsole because a lot of debug printks over slow UART bring kernel to crash.

I can't neither dhcp nor ping via wlan0. but association is ok.

It is a Blackfin board with busybox, not a desktop PC with NetworkManager stuff.

here is ps - nothing special:
PID Uid VSZ Stat Command
1 root 588 S /init
2 root SW< [kthreadd]
3 root SW< [ksoftirqd/0]
4 root SW< [events/0]
5 root SW< [khelper]

   60 root            SW< [kblockd/0]
   74 root            SW< [khubd]
   93 root            SW  [pdflush]
   94 root            SW  [pdflush]
   95 root            SW< [kswapd0]
  101 root            SW< [mediabox2fb]
  162 root            SW< [mtdblockd]
  164 root            SW< [bfin-spi.0]
  179 root            SW< [uwbd]
  184 root            SW< [wusbd]
  209 root            SWN [jffs2_gcd_mtd2]
  214 root        864 R   -/bin/sh
  215 root        496 S   /bin/watchdogd -f -s
  217 root        764 S   /sbin/syslogd -n
  220 root        772 S   /sbin/klogd -n
  230 root            SW< [bf537_trackball]
  234 root        500 S   netsettings_updater
  236 root        504 S   /bin/Apek
  241 root        512 S   /bin/keyhandler

283 root SW< [phy0]
303 root 1776 S wpa_supplicant -Dwext -iwlan0 -c /home/ACORP.conf -dd
334 root 768 R ps -ef

The question is how to verify is it kernel or wpa_supplicant bug or some timing issue.

Regards,
Ivan