WPA2, compat-wireless-2.6.31-rc3, kernel 2.6.28 - rtl8187 - association works but no ping
Hello,
I'm testing rtl8187 on Blackfin platform (linux-2.6.28) compat-wireless-2.6.31-rc3
driver rtl8187
wpa_supplicant-0.6.5
Sympthoms:
Association works but no ping in WPA2(AES) Association works and ping is working with WPA(TKIP)
This is probably not a wpa_supplicant and it's config problem
because it's working (WPA2-AES and WPA-TKIP) on 2.6.28 with corresponding configs.
Any suggestions how to track down the problem?
Best regards,
Ivan
Quoted 1 line · Ivan Kuten
compat-wireless-2.6.31-rc3
compat-wireless-2.6.31-rc4 is out, please try that.
Luis
Quoted 7 lines · Ivan Kuten
Quoted 1 line
compat-wireless-2.6.31-rc3
compat-wireless-2.6.31-rc4 is out, please try that.
Luis
Here is what I get for compat-wireless-2.6.31-rc4:
<6>cfg80211: Using static regulatory domain info
<6>cfg80211: Regulatory domain: US
<6> (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) <6> (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) <6> (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
<6>usb 1-1: new high speed USB device using isp1761 and address 2 <6>cfg80211: Calling CRDA for country: US
<6>usbcore: registered new interface driver rtl8187 <6>usb 1-1: configuration #1 chosen from 1 choice
<6>hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 3 ports detected
<6>usb 1-1.1: new high speed USB device using isp1761 and address 3 <6>usb 1-1.1: configuration #1 chosen from 1 choice <7>phy0: Selected rate control algorithm 'minstrel' <6>phy0: hwaddr 00277080, RTL8187vB (default) V1 + rtl8225z2 <7>phy0: device now idle
<7>phy0: device no longer idle - scanning
<7>phy0: device now idle
<7>phy0: device no longer idle - in use
<7>wlan0: authenticate with AP 01a4b568
<7>wlan0: authenticated
<7>wlan0: associate with AP 01a4b568
<7>wlan0: RX AssocResp from 003e101a (capab=0x411 status=0 aid=2) <7>wlan0: associated
<7>phy0: Allocated STA 002fbfc4
<7>phy0: Inserted STA 002fbfc4
<7>wlan0: switched to short slot time (BSSID=01a4b568)
iwconfig output:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"ACORP"
Mode:Managed Frequency:2.462 GHz Access Point: 00:02:72:74:AC:85
Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:2BAC-63B9-5D99-CF9A-4D39-079F-BB55-5D39 [2] Power Management:off
Link Quality=61/70 Signal level=-49 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
ifconfig:
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:188 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)
wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)
wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Neither dhcp nor setting static IP for wlan0 - no ping.
Regards,
Ivan
Quoted 34 lines · Ivan Kuten
Quoted 7 lines · Ivan Kuten
Quoted 1 line
compat-wireless-2.6.31-rc3
compat-wireless-2.6.31-rc4 is out, please try that.
Luis
Here is what I get for compat-wireless-2.6.31-rc4:
<6>cfg80211: Using static regulatory domain info
<6>cfg80211: Regulatory domain: US
<6> (start_freq-end_freq@ bandwidth), (max_antenna_gain,max_eirp) <6> (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) <6> (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) <6> (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) <6>usb 1-1: new high speed USB device using isp1761 and address 2 <6>cfg80211: Calling CRDA for country: US
<6>usbcore: registered new interface driver rtl8187
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>hub 1-1:1.0: USB hub found
<6>hub 1-1:1.0: 3 ports detected
<6>usb 1-1.1: new high speed USB device using isp1761 and address 3 <6>usb 1-1.1: configuration #1 chosen from 1 choice
<7>phy0: Selected rate control algorithm 'minstrel'
<6>phy0: hwaddr 00277080, RTL8187vB (default) V1 + rtl8225z2 <7>phy0: device now idle
<7>phy0: device no longer idle - scanning
<7>phy0: device now idle
<7>phy0: device no longer idle - in use
Quoted 8 lines
<7>wlan0: authenticate with AP
01a4b568
<7>wlan0: authenticated
<7>wlan0: associate with AP01a4b568
<7>wlan0: RX AssocResp from003e101a(capab=0x411 status=0 aid=2) <7>wlan0: associated
<7>phy0: Allocated STA002fbfc4
<7>phy0: Inserted STA002fbfc4
<7>wlan0: switched to short slot time (BSSID=01a4b568)
This looks peachy.
Quoted 21 lines
iwconfig output:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:"ACORP"
Mode:Managed Frequency:2.462 GHz Access Point: 00:02:72:74:AC:85 Bit Rate=1 Mb/s Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:2BAC-63B9-5D99-CF9A-4D39-079F-BB55-5D39 [2] Power Management:off
Link Quality=61/70 Signal level=-49 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0ifconfig:
Quoted 7 lines
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:188 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)
Note an IP address on eth0, most likely you have a default route using eht0 as well. Check with 'ip route'.
Quoted 7 lines
wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)
Quoted 8 lines
wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)Neither dhcp nor setting static IP for wlan0 - no ping.
Do you have Network Manager on? Please read:
http://wireless.kernel.org/en/users/Documentation/Reporting_bugs
Specifically the section that describes getting 'iw event -t' log and Network Manager.
Luis
Quoted 10 lines
Quoted 9 lines
ifconfig:
eth0 Link encap:Ethernet HWaddr 02:80:AD:20:31:EB
inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:40 errors:0 dropped:0 overruns:0 frame:0 TX packets:188 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:4077 (3.9 KiB) TX bytes:17012 (16.6 KiB)
Quoted 3 lines
Note an IP address on eth0, most likely you have a default route using eht0 as well. Check with 'ip route'.
No default route. eth0 only for netconsole.
I'm doing udhcpc on wlan0.
Another thing is that WPA-TKIP is working. The problem only with CCMP. I posted also in wpa_supplicant list with detailed wpa_supplicant log:
http://lists.shmoo.com/pipermail/hostap/2009-July/020026.html
Quoted 14 lines
Quoted 14 lines
wlan0 Link encap:Ethernet HWaddr 00:12:0E:98:67:FC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:304 (304.0 B) TX bytes:3932 (3.8 KiB)wmaster0 Link encap:UNSPEC HWaddr 00-12-0E-98-67-FC-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Quoted 4 lines
Quoted 1 line
Neither dhcp nor setting static IP for wlan0 - no ping.
Do you have Network Manager on? Please read:
No Network Manager.
Just:wpa_supplicant -Dwext -iwlan0 -c /home/ACORP.conf -dd & /sbin/udhcpc -n -q -i wlan0 -s /bin/default.script
Quoted 5 lines
http://wireless.kernel.org/en/users/Documentation/Reporting_bugs
Specifically the section that describes getting 'iw event -t' log and Network Manager.
I'll try with iw event -t.
Is it possible to check via debugfs something like number of received unencrypted packets?
Regards,
Ivan
Quoted 4 lines · Ivan Kuten
No Network Manager.
Just:wpa_supplicant-Dwext -iwlan0 -c/home/ACORP.conf-dd &/sbin/udhcpc-n -q -i wlan0 -s/bin/default.script
How did you get the eth0 IP? ps -ef?
Luis
Quoted 6 lines · Ivan Kuten
Quoted 4 lines
No Network Manager.
Just:wpa_supplicant-Dwext -iwlan0 -c/home/ACORP.conf-dd &/sbin/udhcpc-n -q -i wlan0 -s/bin/default.script
Quoted 6 lines
How did you get the eth0 IP? ps -ef?
Luis
in rc script it's ifconfig eth0 192.168.5.1
it's the same behaviour without eth0. I'm using eth0 for netconsole because a lot of debug printks over slow UART bring kernel to crash.
I can't neither dhcp nor ping via wlan0. but association is ok.
It is a Blackfin board with busybox, not a desktop PC with NetworkManager stuff.
here is ps - nothing special:
PID Uid VSZ Stat Command
1 root 588 S /init
2 root SW< [kthreadd]
3 root SW< [ksoftirqd/0]
4 root SW< [events/0]
5 root SW< [khelper]
60 root SW< [kblockd/0] 74 root SW< [khubd] 93 root SW [pdflush] 94 root SW [pdflush] 95 root SW< [kswapd0] 101 root SW< [mediabox2fb] 162 root SW< [mtdblockd] 164 root SW< [bfin-spi.0] 179 root SW< [uwbd] 184 root SW< [wusbd] 209 root SWN [jffs2_gcd_mtd2] 214 root 864 R -/bin/sh 215 root 496 S /bin/watchdogd -f -s 217 root 764 S /sbin/syslogd -n 220 root 772 S /sbin/klogd -n 230 root SW< [bf537_trackball] 234 root 500 S netsettings_updater 236 root 504 S /bin/Apek 241 root 512 S /bin/keyhandler
283 root SW< [phy0]
303 root 1776 S wpa_supplicant -Dwext -iwlan0 -c /home/ACORP.conf -dd
334 root 768 R ps -ef
The question is how to verify is it kernel or wpa_supplicant bug or some timing issue.
Regards,
Ivan