add TI DA8xx support: Add new directory for da830evm board
PATCH v2 3/4 add TI DA8xx support: Add new directory for da830evm board
Add new directory for da830evm board
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum Digital EVM board. See http://www.spectrumdigital.com/
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
---
Applies to u-boot-ti
board/davinci/da830evm/Makefile | 52 ++++++++++++ board/davinci/da830evm/board_init.S | 29 +++++++ board/davinci/da830evm/config.mk | 45 ++++++++++ board/davinci/da830evm/dv_board.c | 156 +++++++++++++++++++++++++++++++++++ 4 files changed, 282 insertions(+), 0 deletions(-)
board/davinci/da830evm/Makefile new file +52 -0
@@ -0,0 +1,52 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn <[email protected]> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := dv_board.o +SOBJS := board_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
board/davinci/da830evm/board_init.S new file +29 -0
@@ -0,0 +1,29 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn <[email protected]> + * + * Board-specific low level initialization code. Called at the very end + * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no + * initialization required. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> + +.globl dv_board_init +dv_board_init: + + mov pc, lr
board/davinci/da830evm/config.mk new file +45 -0
45 lines not on this page · raw message
board/davinci/da830evm/dv_board.c new file +156 -0
156 lines not on this page · raw message
PATCH v2 3/4 add TI DA8xx support: Add new directory for da830evm board
Quoted 103 lines · Nick Thompson
Add new directory for da830evm board
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum Digital EVM board. See http://www.spectrumdigital.com/
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).Signed-off-by Nick Thompson <[email protected]>---
Applies to u-boot-tiboard/davinci/da830evm/Makefile | 52 ++++++++++++ board/davinci/da830evm/board_init.S | 29 +++++++ board/davinci/da830evm/config.mk | 45 ++++++++++ board/davinci/da830evm/dv_board.c | 156 +++++++++++++++++++++++++++++++++++ 4 files changed, 282 insertions(+), 0 deletions(-)board/davinci/da830evm/Makefile new file +52
-0@@ -0,0 +1,52 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn <[email protected]> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := dv_board.o +SOBJS := board_init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak *~ .depend + +######################################################################### +# This is for $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/davinci/da830evm/board_init.S new file +19
-0@@ -0,0 +1,29 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn <[email protected]> + * + * Board-specific low level initialization code. Called at the very end + * of cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no + * initialization required. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software
board/davinci/da830evm/board_init.S line 29
Quoted 10 lines
board/davinci/da830evm/board_init.S new file +10
-0+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <config.h> + +.globl dv_board_init +dv_board_init: + + mov pc, lr
This and the trivial lowlevel_init.S file makes me think you just use CONFIG_SKIP_LOWLEVEL_INIT and reduce your file count by 2
board/davinci/da830evm/dv_board.c
Quoted 56 lines
board/davinci/da830evm/config.mk new file +45
-0@@ -0,0 +1,45 @@ +# +# (C) Copyright 2008 Sekhar Nori, Texas Instruments, Inc. <[email protected]> +# +# Copyright (C) 2007 Sergey Kubushyn <[email protected]> +# +# (C) Copyright 2003 Swaminathan, Texas Instruments, <[email protected]> +# +# (C) Copyright 2002 +# Gary Jennejohn, DENX Software Engineering, <[email protected]> +# David Mueller, ELSOFT AG, <[email protected]> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# Texas Instruments DA8xx EVM board (ARM925EJS) cpu +# see http://www.ti.com/ for more information on Texas Instruments +# +# DA8xx EVM has 1 bank of 64 MB SDRAM (2 16Meg x16 chips). +# Physical Address: +# C000'0000 to C400'0000 +# +# Linux-Kernel is expected to be at C000'8000, entry C000'8000 +# (mem base + reserved) +# +# we load ourself to C108 '0000 + + +#Provide at least 16MB spacing between us and the Linux Kernel image +TEXT_BASE = 0xC1080000board/davinci/da830evm/dv_board.c new file +0
-0
Change this file to be da830evm.c
Quoted 42 lines
board/davinci/da830evm/dv_board.c new file +41
-0@@ -0,0 +1,156 @@ +/* +* Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <[email protected]> +* +* Use the board_eth_init hook to initialise the ethernet in the +* correct order. (Has to wait until after call to miiphy_init().) +* +* Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <[email protected]> +* +* Modified for DA8xx EVM. +* +* Copyright (C) 2007 Sergey Kubushyn <[email protected]> +* +* Parts are shamelessly stolen from various TI sources, original copyright +* follows: +* ----------------------------------------------------------------- +* +* Copyright (C) 2004 Texas Instruments. +* +* ---------------------------------------------------------------------------- +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +* ---------------------------------------------------------------------------- +*/ + +#include <common.h> +#include <i2c.h> +#include <net.h> +#include <netdev.h> +#include <asm/arch/hardware.h> +#include <asm/arch/emac_defs.h>
board/davinci/da830evm/dv_board.c line 51
Quoted 10 lines
board/davinci/da830evm/dv_board.c new file +10
-0+#include <asm/io.h> +#include "../common/misc.h" + +DECLARE_GLOBAL_DATA_PTR ; + +/* Works on Always On power domain only (no PD argument) */ +void lpsc_on (unsigned int id) +{ +unsigned int mdstat, mdctl, ptstat, ptcmd; +
You are passing in #defined numbers
but are checking against hardcoded values Please change this to also use #defines
Quoted 24 lines
board/davinci/da830evm/dv_board.c new file +24
-0+if (id >=64 ) +return ; + +if (id <32 ) { + mdstat =PSC0_MDSTAT + (id *4 ); + mdctl =PSC0_MDCTL + (id *4 ); + ptstat =PSC0_PTSTAT ; + ptcmd =PSC0_PTCMD ; + }else { + id -=32 ; + mdstat =PSC1_MDSTAT + (id *4 ); + mdctl =PSC1_MDCTL + (id *4 ); + ptstat =PSC1_PTSTAT ; + ptcmd =PSC1_PTCMD ; + } + +while (readl (ptstat) &0x01 ) + ;/* wait */ + +if ((readl (mdstat) &0x1f ) ==0x03 ) +return ;/* Already on and enabled */ + +writel (readl (mdctl) |0x03 , mdctl); +
board/davinci/da830evm/dv_board.c line 85
Quoted 10 lines
board/davinci/da830evm/dv_board.c new file +10
-0+writel (0x01 , ptcmd); + +while (readl (ptstat) &0x01 ) + ;/* wait */ +while ((readl (mdstat) &0x1f ) !=0x03 ) + ;/* wait */ +} + +/* Read, Modify, Write macro for pin multiplxer modifications */ +#define PINMUX (n, val, mask) writel((val & mask) | (readl(n) & (~mask)), n)
Can this be moved to common/misc.h ?
Other davinci's that do mux-ing could benefit from a common macro.
board/davinci/da830evm/dv_board.c line 98
Quoted 13 lines
board/davinci/da830evm/dv_board.c new file +13
-0+ +int board_init (void ) +{ + +#ifndef CONFIG_USE_IRQ +/* +* Mask all IRQs by clearing the global enable and setting +* the enable clear for all the 90 interrupts. This code is +* also included in low level init. Including it here in case +* low level init is skipped. Not removing it from low level +* init in case some of the low level init code generates +* interrupts... Not expected... but you never know... +*/
This comment does not go with the noop-ish lowlevel_init code. Please change this.
Quoted 41 lines
board/davinci/da830evm/dv_board.c new file +41
-0+ +writel (0 ,INTC_GLB_EN ); + +writel (0 ,INTC_HINT_EN +0x0 ); +writel (0 ,INTC_HINT_EN +0x4 ); +writel (0 ,INTC_HINT_EN +0x8 ); + +writel (0xffffffff ,INTC_EN_CLR0 +0x0 ); +writel (0xffffffff ,INTC_EN_CLR0 +0x4 ); +writel (0xffffffff ,INTC_EN_CLR0 +0x8 ); +#endif + +/* arch number of the board */ + gd->bd->bi_arch_number =MACH_TYPE_DAVINCI_DA830_EVM ; + +/* address of boot parameters */ + gd->bd->bi_boot_params =LINUX_BOOT_PARAM_ADDR ; + +/* +* Power on required peripherals +* ARM does not have access by default to PSC0 and PSC1 +* assuming here that the DSP bootloader has set the IOPU +* such that PSC access is available to ARM +*/ +lpsc_on (DAVINCI_LPSC_AEMIF );/* NAND, NOR */ +lpsc_on (DAVINCI_LPSC_SPI0 );/* Serial Flash */ +lpsc_on (DAVINCI_LPSC_EMAC );/* image download */ +lpsc_on (DAVINCI_LPSC_UART2 );/* console */ +lpsc_on (DAVINCI_LPSC_GPIO ); + +/* Pin Muxing support */ + +/* setup the SUSPSRC for ARM to control emulation suspend */ +writel (readl (SUSPSRC ) & ~(SUSPSRC_EMAC |SUSPSRC_I2C |SUSPSRC_SPI0 | +SUSPSRC_TIMER0 |SUSPSRC_UART2 ),SUSPSRC ); + +#ifdef CONFIG_USE_PINMUX + +#ifdef CONFIG_SPI_FLASH +/* SPI0 pin enable*/ +PINMUX (PINMUX7 ,0x11111000 ,0xFFFFF000 )
board/davinci/da830evm/dv_board.c line 149
Quoted 10 lines
board/davinci/da830evm/dv_board.c new file +10
-0+#endif + +/* UART pin enable */ +PINMUX (PINMUX8 ,0x20000000 ,0xF0000000 ); +PINMUX (PINMUX9 ,0x00000002 ,0x0000000F ); + +/* I2C pin enable */ +PINMUX (PINMUX9 ,0x00022000 ,0x000FF000 ); + +#endif /* CONFIG_USE_PIN_MUX */
Please de-magic these numbers if possible.
board/davinci/da830evm/dv_board.c line 154
Quoted 5 lines
board/davinci/da830evm/dv_board.c new file +5
-0+ +/* enable the console UART */ +writel (PWREMU_MGMT_FREE |PWREMU_MGMT_URRST |PWREMU_MGMT_UTRST , +DAVINCI_UART2_BASE +PWREMU_MGMT_BASE ); +
Will this work if the UART mux is not configured ?
Tom
Quoted 6 lines
board/davinci/da830evm/dv_board.c new file +2
-0+return (0 ); +}_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot