Skip to contentSkip to conversation

add TI DA8xx support:

PATCH Superseded Nick Thompson 3 participants 5 messages Nov 10, 2009 – Nov 12, 2009

lore
Share & tools
lore
#0 lore raw

v5 cover add TI DA8xx support:

Add initial support for DA8xx SoC's and the spectrum digital DA830 EVM board.

See:

	http://www.ti.com
	http://www.spectrumdigital.com/

DA8xx is similar to DaVinci devices, but has a differing memory map and updated peripherals. It is intended that DaVinci drivers will be modified in some way to support these differences.

A side effect of this is that there are some legacy code constructs in this patch set that are required to utilize the DaVinci drivers as they stand now. For example there are some volatiles and memory pointer types defined that are no longer considered acceptable.

The new code in this patch set doesn't use these constructs and the remaining artefacts can be removed when the DaVinci drivers stop using them.

This patch set is based on code originally from TI.
---
Changes from previous patch set:

#defines of constant variables to lower case
load registers only as required in clk_get()

This patch set depends on "[PATCH V3] Davinci: add a pin multiplexer

    configuration API" posted on 2009-11-04

Applies to u-boot-ti:

#1 lore raw

v5 cover add TI DA8xx support:

Quoted 22 lines · Nick Thompson

Add initial support for DA8xx SoC's and the spectrum digital DA830 EVM board.

See:

	http://www.ti.com
	http://www.spectrumdigital.com/

DA8xx is similar to DaVinci devices, but has a differing memory map and updated peripherals. It is intended that DaVinci drivers will be modified in some way to support these differences.

A side effect of this is that there are some legacy code constructs in this patch set that are required to utilize the DaVinci drivers as they stand now. For example there are some volatiles and memory pointer types defined that are no longer considered acceptable.

The new code in this patch set doesn't use these constructs and the remaining artefacts can be removed when the DaVinci drivers stop using them.

This patch set is based on code originally from TI.
---
Changes from previous patch set:

Quoted 7 lines

#defines of constant variables to lower case
load registers only as required in clk_get()

This patch set depends on "[PATCH V3] Davinci: add a pin multiplexer

    configuration API" posted on 2009-11-04

Yes it is dependent.
There is a compile error without the pin mux function.

Once the pin multiplex patch is ack-ed then
Ack to this patch set.

Thanks
Tom

Quoted 6 lines

Applies to u-boot-ti:
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

#2 lore raw

v5 cover add TI DA8xx support:

Quoted 6 lines · Tom
Quoted 4 lines · Nick Thompson

Add initial support for DA8xx SoC's and the spectrum digital DA830 EVM board.

This patch set depends on "[PATCH V3] Davinci: add a pin multiplexer

    configuration API" posted on 2009-11-04
Quoted 8 lines

Yes it is dependent.
There is a compile error without the pin mux function.

Once the pin multiplex patch is ack-ed then
Ack to this patch set.

Thanks
Tom

I've submitted an update for the pinmux functions, based on your comments.

Thanks for the Ack,
Nick.

#3 lore raw

v5 cover add TI DA8xx support:

Quoted 9 lines · Nick Thompson
Quoted 8 lines · Tom
Quoted 4 lines · Nick Thompson

Add initial support for DA8xx SoC's and the spectrum digital DA830 EVM board.

This patch set depends on "[PATCH V3] Davinci: add a pin multiplexer

    configuration API" posted on 2009-11-04

Yes it is dependent.
There is a compile error without the pin mux function.

Quoted 8 lines
Quoted 5 lines

Once the pin multiplex patch is ack-ed then
Ack to this patch set.

Thanks
Tom

I've submitted an update for the pinmux functions, based on your comments.

Yes. Your changes are fine.

Sandeep,
Can you push this the pinmux and then this change to the arm-ti ?

Tom

Quoted 2 lines

Thanks for the Ack,
Nick.

#4 lore raw

v5 cover add TI DA8xx support:

Quoted 26 lines

-----Original Message-----
From: Tom [mailto:Tom.Rix at windriver.com]
Sent: Thursday, November 12, 2009 8:42 AM
To: Nick Thompson; Paulraj, Sandeep
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH V5 0/4] add TI DA8xx support:

Quoted 3 lines · Nick Thompson
Quoted 2 lines · Tom
Quoted 1 line · Nick Thompson

Add initial support for DA8xx SoC's and the spectrum digital DA830 EVM

board.

Quoted 6 lines
Quoted 6 lines
Quoted 3 lines

This patch set depends on "[PATCH V3] Davinci: add a pin multiplexer

    configuration API" posted on 2009-11-04

Yes it is dependent.
There is a compile error without the pin mux function.

Quoted 7 lines
Quoted 5 lines

Once the pin multiplex patch is ack-ed then
Ack to this patch set.

Thanks
Tom

I've submitted an update for the pinmux functions, based on your

Quoted 8 lines

comments.

Quoted 1 line

Yes. Your changes are fine.

Sandeep,
Can you push this the pinmux and then this change to the arm-ti ?

Tom

Will do it this weekend.

Quoted 4 lines
Quoted 3 lines

Thanks for the Ack,
Nick.