add TI DA8xx support: Integrate DA830 EVM support into U-Boot
PATCH v2 4/4 add TI DA8xx support: Integrate DA830 EVM support into U-Boot
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum Digital EVM board. See http://www.spectrumdigital.com/
---
Applies to u-boot-ti
MAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + include/common.h | 4 + include/configs/da830evm.h | 244 ++++++++++++++++++++++++++++++++++++++++++++ 5 files changed, 256 insertions(+), 0 deletions(-)
MAINTAINERS +4 -0
@@ -712,6 +712,10 @@ Andrea Scian <[email protected]> B2 ARM7TDMI (S3C44B0X) +Nick Thompson <[email protected]> + + da830evm ARM926EJS (DA830/OMAP-L137) + Albin Tonnerre <[email protected]> sbc35_a9g20 ARM926EJS (AT91SAM9G20 SoC)
MAKEALL +1 -0
@@ -569,6 +569,7 @@ LIST_ARM9=" \ davinci_dm355evm \ davinci_dm355leopard \ davinci_dm6467evm \ + da830evm \ " #########################################################################
Makefile +3 -0
@@ -2936,6 +2936,9 @@ davinci_dm365evm_config : unconfig davinci_dm6467evm_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm davinci davinci +da830evm_config: unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci da8xx + imx27lite_config: unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27
include/common.h +4 -0
@@ -107,6 +107,10 @@ typedef volatile unsigned char vu_char;#ifdef CONFIG_BLACKFIN #include <asm/blackfin.h> #endif +#ifdef CONFIG_SOC_DA8XX +#include <asm/arch/hardware.h> +#endif +#include <part.h> #include <flash.h>
include/configs/da830evm.h new file +244 -0
244 lines not on this page · raw message
PATCH v2 4/4 add TI DA8xx support: Integrate DA830 EVM support into U-Boot
Quoted 107 lines · Nick Thompson
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum Digital EVM board. See http://www.spectrumdigital.com/
Signed-off-by Nick Thompson <[email protected]>---
Applies to u-boot-tiMAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + include/common.h | 4 + include/configs/da830evm.h | 244 ++++++++++++++++++++++++++++++++++++++++++++ 5 files changed, 256 insertions(+), 0 deletions(-)MAINTAINERS +4
-0@@ -712,6 +712,10 @@ Andrea Scian <[email protected]> B2 ARM7TDMI (S3C44B0X) +Nick Thompson <[email protected]> + + da830evm ARM926EJS (DA830/OMAP-L137) + Albin Tonnerre <[email protected]> sbc35_a9g20 ARM926EJS (AT91SAM9G20 SoC)MAKEALL +1
-0@@ -569,6 +569,7 @@ LIST_ARM9=" \ davinci_dm355evm \ davinci_dm355leopard \ davinci_dm6467evm \ + da830evm \ " #########################################################################Makefile +3
-0@@ -2936,6 +2936,9 @@ davinci_dm365evm_config : unconfig davinci_dm6467evm_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm davinci davinci +da830evm_config: unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci da8xx + imx27lite_config: unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27include/common.h +4
-0@@ -107,6 +107,10 @@ typedef volatile unsigned char vu_char;#ifdef CONFIG_BLACKFIN #include <asm/blackfin.h> #endif +#ifdef CONFIG_SOC_DA8XX +#include <asm/arch/hardware.h> +#endif +#include <part.h> #include <flash.h> include/configs/da830evm.h new file +29
-0@@ -0,0 +1,244 @@ +/* +* Copyright (C) 2008 Texas Instruments, Inc <www.ti.com> +* +* Based on davinci_dvevm.h. Original Copyrights follow: +* +* Copyright (C) 2007 Sergey Kubushyn <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h> +#include <asm/arch/clock.h> + +/*
include/configs/da830evm.h line 39
Quoted 10 lines
include/configs/da830evm.h new file +10
-0+* Board +*/ + +/* +* SoC Configuration +*/ +#define CONFIG_MACH_DAVINCI_DA830_EVM +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
Extra space at end of ..CLK_FREQ
optional fix
Quoted 205 lines
include/configs/da830evm.h new file +205
-0+#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#undef CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ + +/* +* Memory Info +*/ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024)/* malloc() len */ +#define CONFIG_SYS_GBL_DATA_SIZE 128/* reserved for initial data */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE/* DDR Start */ +#define PHYS_SDRAM_1_SIZE 0x04000000/* SDRAM size 64MB */ +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024)/* 16MB test */ +#define CONFIG_NR_DRAM_BANKS 1/* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024)/* regular stack */ + +/* +* Serial Driver info +*/ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4/* NS16550 register size */ +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE/* Base address of UART2 */ +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1/* use UART0 for console */ +#define CONFIG_BAUDRATE 115200/* Default baud rate */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* +* I2C Configuration +*/ +#define CONFIG_HARD_I2C +#define CONFIG_DRIVER_DAVINCI_I2C +#define CONFIG_SYS_I2C_SPEED 25000/* 100Kbps won't work, H/W bug */ +#define CONFIG_SYS_I2C_SLAVE 10/* Bogus, master-only in U-Boot */ + +/* +* I2C EEPROM definitions for catalyst 24W256 EEPROM chip +*/ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* +* Network & Ethernet Configuration +*/ +#ifdef CONFIG_DRIVER_TI_EMAC +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#endif + +/* +* Flash & Environment +*/ +#ifdef CONFIG_USE_NAND +#undef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CONFIG_ENV_OFFSET 0x0/* Block 0--not used by bootcode */ +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_SYS_CLE_MASK 0x10 +#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1/* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 +#define DEF_BOOTM "" +#endif + +#ifdef CONFIG_USE_NOR +#define CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_MAX_FLASH_BANKS 1/* max number of flash banks */ +#define CONFIG_SYS_FLASH_SECT_SZ (64 << 10)/* 64KB */ +#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3) +#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE +#define PHYS_FLASH_SIZE (32 << 20)/* Flash size 32MB */ +#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) +#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ +#define CONFIG_SYS_FLASH_SPL_ACCESS +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#define CONFIG_ENV_OFFSET (256 << 10) +#define CONFIG_ENV_SECT_SIZE 4096 +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID) +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#endif + + +/* +* U-Boot general configuration +*/ +#undef CONFIG_USE_IRQ/* No IRQ/FIQ in U-Boot */ +#undef CONFIG_MISC_INIT_R +#undef CONFIG_BOOTDELAY +#define CONFIG_BOOTFILE "uImage"/* Boot file name */ +#define CONFIG_SYS_PROMPT "DA830-evm > "/* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +#define CONFIG_USE_PINMUX + +/* +* Linux Information +*/ +#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS "mem=32M console=ttyS2,115200n8 root=/dev/mtdblock/2 rw noinitrd ip=dhcp" +#define CONFIG_BOOTCOMMAND "" +#define CONFIG_BOOTDELAY 3 + +/* +* U-Boot commands +*/ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#define CONFIG_CMD_EEPROM + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#endif + +#ifdef CONFIG_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_UBI +#define CONFIG_RBTREE +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SAVEENV +#endif + +#if !defined(CONFIG_USE_NAND ) && \ + !defined(CONFIG_USE_NOR ) && \ + !defined(CONFIG_USE_SPIFLASH ) +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_ENV +#endif + +#ifdef CONFIG_USB_DA8XX +#define CONFIG_CMD_USB /* include support for usb */ +#define CONFIG_CMD_STORAGE /* include support for usb */ +#define CONFIG_CMD_FAT /* include support for FAT/storage*/ +#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/ +#endif + +#endif /* __CONFIG_H */
Quoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
This is fine.
Ack-ed
Tom
Paulraj
PATCH v2 4/4 add TI DA8xx support: Integrate DA830 EVM support into U-Boot
Quoted 103 lines
Quoted 3 lines · Nick Thompson
Integrate DA830 EVM support into U-Boot.
Provides initial support for TI OMAP-L137/DA830 SoC devices on a
Spectrum
Quoted 11 lines
Digital EVM board. See http://www.spectrumdigital.com/
Signed-off-by Nick Thompson <[email protected]>---
Applies to u-boot-tiMAINTAINERS | 4 + MAKEALL | 1 + Makefile | 3 + include/common.h | 4 + include/configs/da830evm.h | 244++++++++++++++++++++++++++++++++++++++++++++
Quoted 22 lines
5 files changed, 256 insertions(+), 0 deletions(-)MAINTAINERS +4
-0@@ -712,6 +712,10 @@ Andrea Scian <[email protected]> B2 ARM7TDMI (S3C44B0X) +Nick Thompson <[email protected]> + + da830evm ARM926EJS (DA830/OMAP-L137) + Albin Tonnerre <[email protected]> sbc35_a9g20 ARM926EJS (AT91SAM9G20 SoC)MAKEALL +0
-0MAKEALL LIST_ARM9=" \ · line 575
Quoted 7 lines
MAKEALL +1
-0@@ -569,6 +569,7 @@ LIST_ARM9=" \ davinci_dm355evm \ davinci_dm355leopard \ davinci_dm6467evm \ + da830evm \ "#########################################################################
Quoted 53 lines
Makefile +3
-0@@ -2936,6 +2936,9 @@ davinci_dm365evm_config : unconfig davinci_dm6467evm_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs dm6467evm davinci davinci +da830evm_config: unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs da830evm davinci da8xx + imx27lite_config: unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs imx27lite logicpd mx27include/common.h +4
-0@@ -107,6 +107,10 @@ typedef volatile unsigned char vu_char;#ifdef CONFIG_BLACKFIN #include <asm/blackfin.h> #endif +#ifdef CONFIG_SOC_DA8XX +#include <asm/arch/hardware.h> +#endif +#include <part.h> #include <flash.h> include/configs/da830evm.h new file +18
-0@@ -0,0 +1,244 @@ +/* +* Copyright (C) 2008 Texas Instruments, Inc <www.ti.com> +* +* Based on davinci_dvevm.h. Original Copyrights follow: +* +* Copyright (C) 2007 Sergey Kubushyn <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License
Quoted 8 lines
include/configs/da830evm.h line 26
Quoted 8 lines
include/configs/da830evm.h new file +8
-0+* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h>
I have cleaned up DaVinci and OMAP3 configs and they no longer use this header file. This header file might disappear from future versions of U-boot Take a look at
http://git.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=commit;h=a16df2c11188297eca43cf6080c70fb69b960232
Quoted 238 lines
include/configs/da830evm.h line 39
Quoted 13 lines
include/configs/da830evm.h new file +13
-0+#include <asm/arch/clock.h> + +/* +* Board +*/ + +/* +* SoC Configuration +*/ +#define CONFIG_MACH_DAVINCI_DA830_EVM +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)Extra space at end of ..CLK_FREQ
optional fixinclude/configs/da830evm.h
Quoted 6 lines
include/configs/da830evm.h new file +6
-0+#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_HZ 1000 +#undef CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */
include/configs/da830evm.h
Quoted 5 lines
include/configs/da830evm.h new file +5
-0+ +/* +* Memory Info +*/ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024)/* malloc() len */
include/configs/da830evm.h
Quoted 5 lines
include/configs/da830evm.h new file +5
-0+#define CONFIG_SYS_GBL_DATA_SIZE 128/* reserved for initial data */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE/* DDR Start */ +#define PHYS_SDRAM_1_SIZE 0x04000000/* SDRAM size 64MB */ +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 16*1024*1024)/* 16MB test */
include/configs/da830evm.h
Quoted 9 lines
include/configs/da830evm.h new file +9
-0+#define CONFIG_NR_DRAM_BANKS 1/* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024)/* regular stack */ + +/* +* Serial Driver info +*/ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4/* NS16550 register size */
include/configs/da830evm.h line 65
Quoted 1 line
include/configs/da830evm.h new file +1
-0+#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE/* Base address of UART2 */
include/configs/da830evm.h
Quoted 3 lines
include/configs/da830evm.h new file +3
-0+#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1/* use UART0 for console */ +#define CONFIG_BAUDRATE 115200/* Default baud rate */
include/configs/da830evm.h line 69
Quoted 1 line
include/configs/da830evm.h new file +1
-0+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600,115200 }
include/configs/da830evm.h
Quoted 7 lines
include/configs/da830evm.h new file +7
-0+ +/* +* I2C Configuration +*/ +#define CONFIG_HARD_I2C +#define CONFIG_DRIVER_DAVINCI_I2C +#define CONFIG_SYS_I2C_SPEED 25000/* 100Kbps won't work, H/W bug */
include/configs/da830evm.h line 77
Quoted 1 line
include/configs/da830evm.h new file +1
-0+#define CONFIG_SYS_I2C_SLAVE 10/* Bogus, master-only in U- Boot */
Quoted 21 lines
include/configs/da830evm.h new file +21
-0+ +/* +* I2C EEPROM definitions for catalyst 24W256 EEPROM chip +*/ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* +* Network & Ethernet Configuration +*/ +#ifdef CONFIG_DRIVER_TI_EMAC +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#endif include/configs/da830evm.h
Quoted 10 lines
include/configs/da830evm.h new file +10
-0+ +/* +* Flash & Environment +*/ +#ifdef CONFIG_USE_NAND +#undef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CONFIG_ENV_OFFSET 0x0/* Block 0--not used by bootcode */
include/configs/da830evm.h
Quoted 8 lines
include/configs/da830evm.h new file +8
-0+#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_SYS_CLE_MASK 0x10 +#define CONFIG_SYS_ALE_MASK 0x8 +#define CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1/* Max number of NAND devices */
include/configs/da830evm.h
Quoted 10 lines
include/configs/da830evm.h new file +10
-0+#define NAND_MAX_CHIPS 1 +#define DEF_BOOTM "" +#endif + +#ifdef CONFIG_USE_NOR +#define CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_SYS_NO_FLASH +#define CONFIG_SYS_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_MAX_FLASH_BANKS 1/* max number of flash banks */
include/configs/da830evm.h
Quoted 5 lines
include/configs/da830evm.h new file +5
-0+#define CONFIG_SYS_FLASH_SECT_SZ (64 << 10)/* 64KB */ +#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3) +#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE +#define PHYS_FLASH_SIZE (32 << 20)/* Flash size 32MB */ +#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
Quoted 23 lines
include/configs/da830evm.h new file +23
-0+#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ +#define CONFIG_SYS_FLASH_SPL_ACCESS +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_ENV_IS_IN_FLASH +#undef CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#define CONFIG_ENV_OFFSET (256 << 10) +#define CONFIG_ENV_SECT_SIZE 4096 +#define CONFIG_SYS_NO_FLASH +#define CONFIG_SPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID) +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#endif + +include/configs/da830evm.h
Quoted 10 lines
include/configs/da830evm.h new file +10
-0+/* +* U-Boot general configuration +*/ +#undef CONFIG_USE_IRQ/* No IRQ/FIQ in U-Boot */ +#undef CONFIG_MISC_INIT_R +#undef CONFIG_BOOTDELAY +#define CONFIG_BOOTFILE "uImage"/* Boot file name */ +#define CONFIG_SYS_PROMPT "DA830-evm > "/* Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
include/configs/da830evm.h line 166
Quoted 2 lines
include/configs/da830evm.h new file +2
-0+#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Args Buffer Size */
include/configs/da830evm.h
Quoted 3 lines
include/configs/da830evm.h new file +3
-0+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_MEMTEST_START + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
Quoted 5 lines
include/configs/da830evm.h new file +5
-0+#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY include/configs/da830evm.h
Quoted 10 lines
include/configs/da830evm.h new file +10
-0+#define CONFIG_MX_CYCLIC +#define CONFIG_USE_PINMUX + +/* +* Linux Information +*/ +#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100) +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS "mem=32M console=ttyS2,115200n8root=/dev/mtdblock/2 rw noinitrd ip=dhcp"
Quoted 60 lines
include/configs/da830evm.h new file +60
-0+#define CONFIG_BOOTCOMMAND "" +#define CONFIG_BOOTDELAY 3 + +/* +* U-Boot commands +*/ +#include <config_cmd_default.h> +#define CONFIG_CMD_ENV +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_MEMORY +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#define CONFIG_CMD_EEPROM + +#ifndef CONFIG_DRIVER_TI_EMAC +#undef CONFIG_CMD_NET +#endif + +#ifdef CONFIG_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_UBI +#define CONFIG_RBTREE +#endif + +#ifdef CONFIG_USE_SPIFLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SAVEENV +#endif + +#if !defined(CONFIG_USE_NAND ) && \ + !defined(CONFIG_USE_NOR ) && \ + !defined(CONFIG_USE_SPIFLASH ) +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_SIZE (16 << 10) +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_ENV +#endif + +#ifdef CONFIG_USB_DA8XX +#define CONFIG_CMD_USB /* include support for usb */ +#define CONFIG_CMD_STORAGE /* include support for usb */ +#define CONFIG_CMD_FAT /* include support for FAT/storage*/ +#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/ +#endif + +#endif /* __CONFIG_H */