TeVii S470 Tunning Issue (Kernel 2.6.27-21)
Hi all,
I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.
My configuration is :
- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from http://mercurial.intuxication.org/hg/s2-liplianin)last changes at 05/29/2010,
All work fine i.e drivers/firmware installation after madprobe a right modules.
# lsmod Module Size Used by Not tainted cx23885 82416 0 tveeprom 9348 1 cx23885 btcx_risc 1928 1 cx23885 cx2341x 7748 1 cx23885 ir_common 23936 1 cx23885 videobuf_dma_sg 5060 1 cx23885 ir_core 3596 2 cx23885,ir_common v4l2_common 8896 2 cx23885,cx2341x videodev 25376 2 cx23885,v4l2_common videobuf_dvb 2820 1 cx23885 videobuf_core 8388 3 cx23885,videobuf_dma_sg,videobuf_dvb lnbp21 1024 0 dvb_core 54832 2 cx23885,videobuf_dvb ds3000 9668 1
# dmesg Linux video capture interface: v2.00 cx23885 driver version 0.0.2 loaded CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected] cx23885_dvb_register() allocating 1 frontend(s) cx23885[0]: cx23885 based dvb card DS3000 chip version: 0.192 attached. DVB: registering new adapter (cx23885[0]) DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000 cx23885 0000:03:00.0: setting latency timer to 64 tun: Universal TUN/TAP device driver, 1.6
A problem appear when tunning card using szap-s2 :
# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyCh
reading channels from file '/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35 vpid 0x0286, apid 0x1fff, sid 0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fwds3000_firmware_ondemand: Waiting for firmware upload(2)...ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)ds3000_tune: Unable initialise the firmware
Apparently it can't locate a firmware file, yet :
# ls -l /lib/firmware/ -rwxr-xr-x 1 root root 8192 May 3 07:09 dvb-fe-ds3000.fw
Any ideas why this happens?
Thanks and best regards,
Hamza Ferrag
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.
The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.
Good luck,
Hans
Op 13-07-10 20:28, Hamza Ferrag schreef:
Quoted 83 lines
Hi all,
I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.
My configuration is :
- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last changes at 05/29/2010,All work fine i.e
drivers/firmwareinstallation after madprobe a right modules.# lsmod Module Size Used by Not tainted cx23885 82416 0 tveeprom 9348 1 cx23885 btcx_risc 1928 1 cx23885 cx2341x 7748 1 cx23885 ir_common 23936 1 cx23885 videobuf_dma_sg 5060 1 cx23885 ir_core 3596 2 cx23885,ir_common v4l2_common 8896 2 cx23885,cx2341x videodev 25376 2 cx23885,v4l2_common videobuf_dvb 2820 1 cx23885 videobuf_core 8388 3 cx23885,videobuf_dma_sg,videobuf_dvb lnbp21 1024 0 dvb_core 54832 2 cx23885,videobuf_dvb ds3000 9668 1# dmesg Linux video capture interface: v2.00 cx23885 driver version 0.0.2 loaded CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected] cx23885_dvb_register() allocating 1 frontend(s) cx23885[0]: cx23885 based dvb card DS3000 chip version: 0.192 attached. DVB: registering new adapter (cx23885[0]) DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000 cx23885 0000:03:00.0: setting latency timer to 64 tun: Universal TUN/TAP device driver, 1.6A problem appear when tunning card using szap-s2 :
# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyChreading channels from file '
/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35 vpid0x0286, apid0x1fff, sid0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fwds3000_firmware_ondemand: Waiting for firmware upload(2)...ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)ds3000_tune: Unable initialise the firmwareApparently it can't locate a firmware file, yet :
# ls -l /lib/firmware/ -rwxr-xr-x 1 root root 8192 May 3 07:09 dvb-fe-ds3000.fwAny ideas why this happens?
Thanks and best regards,
Hamza Ferrag
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Hi Hans,
Quoted 11 lines · Hans Houwaard
I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.
The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.
Quoted 99 lines
Good luck,
Hans
Op 13-07-10 20:28, Hamza Ferrag schreef:
Quoted 92 lines
Hi all,
I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.
My configuration is :
- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last<http://mercurial.intuxication.org/hg/s2-liplianin%29last>changes at 05/29/2010,All work fine i.e
drivers/firmwareinstallation after madprobe a right modules.# lsmod Module Size Used by Not tainted cx23885 82416 0 tveeprom 9348 1 cx23885 btcx_risc 1928 1 cx23885 cx2341x 7748 1 cx23885 ir_common 23936 1 cx23885 videobuf_dma_sg 5060 1 cx23885 ir_core 3596 2 cx23885,ir_common v4l2_common 8896 2 cx23885,cx2341x videodev 25376 2 cx23885,v4l2_common videobuf_dvb 2820 1 cx23885 videobuf_core 8388 3 cx23885,videobuf_dma_sg,videobuf_dvb lnbp21 1024 0 dvb_core 54832 2 cx23885,videobuf_dvb ds3000 9668 1# dmesg Linux video capture interface: v2.00 cx23885 driver version 0.0.2 loaded CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected] cx23885_dvb_register() allocating 1 frontend(s) cx23885[0]: cx23885 based dvb card DS3000 chip version: 0.192 attached. DVB: registering new adapter (cx23885[0]) DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000 cx23885 0000:03:00.0: setting latency timer to 64 tun: Universal TUN/TAP device driver, 1.6A problem appear when tunning card using szap-s2 :
# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyChreading channels from file '
/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35
vpid0x0286, apid0x1fff, sid0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fwds3000_firmware_ondemand: Waiting for firmware upload(2)...ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)ds3000_tune: Unable initialise the firmwareApparently it can't locate a firmware file, yet :
# ls -l /lib/firmware/ -rwxr-xr-x 1 root root 8192 May 3 07:09 dvb-fe-ds3000.fwAny ideas why this happens?
Thanks and best regards,
Hamza Ferrag
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Hi Hans,
Thanks for your quick feedback.
Any other suggestions guys ? .
Thanks in advance.
Hamza Ferrag.
Quoted 4 lines · ferrag hamza
Hi Hans,
Quoted 113 lines
Quoted 110 lines · Hans Houwaard
I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.
The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.
Good luck,
Hans
Op 13-07-10 20:28, Hamza Ferrag schreef:
Quoted 92 lines
Hi all,
I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.
My configuration is :
- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last<http://mercurial.intuxication.org/hg/s2-liplianin%29last>changes at 05/29/2010,All work fine i.e
drivers/firmwareinstallation after madprobe a right modules.# lsmod Module Size Used by Not tainted cx23885 82416 0 tveeprom 9348 1 cx23885 btcx_risc 1928 1 cx23885 cx2341x 7748 1 cx23885 ir_common 23936 1 cx23885 videobuf_dma_sg 5060 1 cx23885 ir_core 3596 2 cx23885,ir_common v4l2_common 8896 2 cx23885,cx2341x videodev 25376 2 cx23885,v4l2_common videobuf_dvb 2820 1 cx23885 videobuf_core 8388 3 cx23885,videobuf_dma_sg,videobuf_dvb lnbp21 1024 0 dvb_core 54832 2 cx23885,videobuf_dvb ds3000 9668 1# dmesg Linux video capture interface: v2.00 cx23885 driver version 0.0.2 loaded CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected] cx23885_dvb_register() allocating 1 frontend(s) cx23885[0]: cx23885 based dvb card DS3000 chip version: 0.192 attached. DVB: registering new adapter (cx23885[0]) DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000 cx23885 0000:03:00.0: setting latency timer to 64 tun: Universal TUN/TAP device driver, 1.6A problem appear when tunning card using szap-s2 :
# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyChreading channels from file '
/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35
vpid0x0286, apid0x1fff, sid0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fwds3000_firmware_ondemand: Waiting for firmware upload(2)...ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)ds3000_tune: Unable initialise the firmwareApparently it can't locate a firmware file, yet :
# ls -l /lib/firmware/ -rwxr-xr-x 1 root root 8192 May 3 07:09 dvb-fe-ds3000.fwAny ideas why this happens?
Thanks and best regards,
Hamza Ferrag
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
TeVii S470 periodically fails to tune/lock - needs poweroff
Hello Guys,
I have been using my TeVii S470 DVBS2 card for about one month . I am using it with mythtv on fedora 12 using latest kernel , and compiled the latest v4l drivers . The sensitivity and picture is very good both on dvbs and dvbs2 transponders , very happy with that . However several times already when trying to watch live tv on myth the channel failed to tune . Usually happens in the morning after box was running 24x7 for a few days . The only way to restore functionality is to do a power off and wait a couple of mins then power on . If I just do a reboot , this does not help . Strange thing is that I see nothing unusual in the mythtv logs or dmesg/messages log . When the card is in this no-lock state , it will not tune into any transponder even when I run scandvb . After power reset everything works again for a few more days . Any info welcome .
Best Regards
Milorad
Re: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff
Check the temperature of the adapter. It is getting quite hot. I use fans to cool it, which avoids this kind of problems.
--------------------------------------------------
From: "O&M Ugarcina" <[email protected]>
Sent: Friday, September 03, 2010 10:42 AM
To: <[email protected]>
Cc: <[email protected]>
Subject: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff
Quoted 14 lines
Hello Guys,
I have been using my TeVii S470 DVBS2 card for about one month . I am using it with mythtv on fedora 12 using latest kernel , and compiled the latest v4l drivers . The sensitivity and picture is very good both on dvbs and dvbs2 transponders , very happy with that . However several times already when trying to watch live tv on myth the channel failed to tune . Usually happens in the morning after box was running 24x7 for a few days . The only way to restore functionality is to do a power off and wait a couple of mins then power on . If I just do a reboot , this does not help . Strange thing is that I see nothing unusual in the mythtv logs or dmesg/messages log . When the card is in this no-lock state , it will not tune into any transponder even when I run scandvb . After power reset everything works again for a few more days . Any info welcome .
Best Regards
Milorad
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Re: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff
Thanks for that Karsten,
I have checked the temperature and seems normal . It does not look like it is getting overly hot . I have been keeping a close eye on it and it looks like I get more failures when using Diseqc . I notice when going to another satellite then coming back I seem to get more no-locks . My suspicion is that there may be some issues with diseqc function that will crash the card . After a full power down is done card is back in operation with no problems . Could this be a firmware thing ?
Best Regards
Milorad
Quoted 39 lines · Karsten Siebert
Check the temperature of the adapter. It is getting quite hot. I use fans to cool it, which avoids this kind of problems.
--------------------------------------------------
From: "O&M Ugarcina" <[email protected]>
Sent: Friday, September 03, 2010 10:42 AM
To: <[email protected]>
Cc: <[email protected]>
Subject: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroffQuoted 25 lines
Hello Guys,
I have been using my TeVii S470 DVBS2 card for about one month . I am using it with mythtv on fedora 12 using latest kernel , and compiled the latest v4l drivers . The sensitivity and picture is very good both on dvbs and dvbs2 transponders , very happy with that . However several times already when trying to watch live tv on myth the channel failed to tune . Usually happens in the morning after box was running 24x7 for a few days . The only way to restore functionality is to do a power off and wait a couple of mins then power on . If I just do a reboot , this does not help . Strange thing is that I see nothing unusual in the mythtv logs or dmesg/messages log . When the card is in this no-lock state , it will not tune into any transponder even when I run scandvb . After power reset everything works again for a few more days . Any info welcome .
Best Regards
Milorad
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Hi Hans,
Thanks for your quick feedback.
Any other suggestions guys ? .
Thanks in advance.
Hamza Ferrag.
Quoted 109 lines · Hans Houwaard
I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.
The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.
Good luck,
Hans
Op 13-07-10 20:28, Hamza Ferrag schreef:
Quoted 92 lines
Hi all,
I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.
My configuration is :
- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last changes at 05/29/2010,All work fine i.e
drivers/firmwareinstallation after madprobe a right modules.# lsmod Module Size Used by Not tainted cx23885 82416 0 tveeprom 9348 1 cx23885 btcx_risc 1928 1 cx23885 cx2341x 7748 1 cx23885 ir_common 23936 1 cx23885 videobuf_dma_sg 5060 1 cx23885 ir_core 3596 2 cx23885,ir_common v4l2_common 8896 2 cx23885,cx2341x videodev 25376 2 cx23885,v4l2_common videobuf_dvb 2820 1 cx23885 videobuf_core 8388 3 cx23885,videobuf_dma_sg,videobuf_dvb lnbp21 1024 0 dvb_core 54832 2 cx23885,videobuf_dvb ds3000 9668 1# dmesg Linux video capture interface: v2.00 cx23885 driver version 0.0.2 loaded CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected] cx23885_dvb_register() allocating 1 frontend(s) cx23885[0]: cx23885 based dvb card DS3000 chip version: 0.192 attached. DVB: registering new adapter (cx23885[0]) DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)... cx23885_dev_checkrevision() Hardware revision = 0xb0 cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000 cx23885 0000:03:00.0: setting latency timer to 64 tun: Universal TUN/TAP device driver, 1.6A problem appear when tunning card using szap-s2 :
# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyChreading channels from file '
/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35
vpid0x0286, apid0x1fff, sid0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fwds3000_firmware_ondemand: Waiting for firmware upload(2)...ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)ds3000_tune: Unable initialise the firmwareApparently it can't locate a firmware file, yet :
# ls -l /lib/firmware/ -rwxr-xr-x 1 root root 8192 May 3 07:09 dvb-fe-ds3000.fwAny ideas why this happens?
Thanks and best regards,
Hamza Ferrag
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb