Skip to contentSkip to conversation

TeVii S470 Tunning Issue (Kernel 2.6.27-21)

linux-dvb Hamza Ferrag 4 participants 8 messages Jul 13, 2010 – Sep 8, 2010 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Hi all,

I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.

My configuration is :

- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from http://mercurial.intuxication.org/hg/s2-liplianin)last changes at 05/29/2010,

All work fine i.e drivers/firmware installation after madprobe a right modules.

# lsmod
Module                  Size  Used by    Not tainted
cx23885                82416  0
tveeprom                9348  1 cx23885
btcx_risc               1928  1 cx23885
cx2341x                 7748  1 cx23885
ir_common              23936  1 cx23885
videobuf_dma_sg         5060  1 cx23885
ir_core                 3596  2 cx23885,ir_common
v4l2_common             8896  2 cx23885,cx2341x
videodev               25376  2 cx23885,v4l2_common
videobuf_dvb            2820  1 cx23885
videobuf_core           8388  3 cx23885,videobuf_dma_sg,videobuf_dvb
lnbp21                  1024  0
dvb_core               54832  2 cx23885,videobuf_dvb
ds3000                  9668  1
# dmesg
Linux video capture interface: v2.00
cx23885 driver version 0.0.2 loaded
CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected]
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
DS3000 chip version: 0.192 attached.
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000
cx23885 0000:03:00.0: setting latency timer to 64
tun: Universal TUN/TAP device driver, 1.6

A problem appear when tunning card using szap-s2 :

# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyCh

reading channels from file '/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35 vpid 0x0286, apid 0x1fff, sid 0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fw
ds3000_firmware_ondemand: Waiting for firmware upload(2)...
ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)
ds3000_tune: Unable initialise the firmware

Apparently it can't locate a firmware file, yet :

# ls -l  /lib/firmware/
-rwxr-xr-x    1 root     root         8192 May  3 07:09 dvb-fe-ds3000.fw

Any ideas why this happens?

Thanks and best regards,

Hamza Ferrag

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#1 lore raw

I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.

The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.

Good luck,

Hans

Op 13-07-10 20:28, Hamza Ferrag schreef:

Quoted 83 lines

Hi all,

I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.

My configuration is :

- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last changes at 05/29/2010,

All work fine i.e drivers/firmware installation after madprobe a right modules.

# lsmod
Module                  Size  Used by    Not tainted
cx23885                82416  0
tveeprom                9348  1 cx23885
btcx_risc               1928  1 cx23885
cx2341x                 7748  1 cx23885
ir_common              23936  1 cx23885
videobuf_dma_sg         5060  1 cx23885
ir_core                 3596  2 cx23885,ir_common
v4l2_common             8896  2 cx23885,cx2341x
videodev               25376  2 cx23885,v4l2_common
videobuf_dvb            2820  1 cx23885
videobuf_core           8388  3 cx23885,videobuf_dma_sg,videobuf_dvb
lnbp21                  1024  0
dvb_core               54832  2 cx23885,videobuf_dvb
ds3000                  9668  1
# dmesg
Linux video capture interface: v2.00
cx23885 driver version 0.0.2 loaded
CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470 [card=15,autodetected]
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
DS3000 chip version: 0.192 attached.
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (Montage Technology DS3000/TS2020)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio: 0xdf800000
cx23885 0000:03:00.0: setting latency timer to 64
tun: Universal TUN/TAP device driver, 1.6

A problem appear when tunning card using szap-s2 :

# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyCh

reading channels from file '/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35 vpid 0x0286, apid 0x1fff, sid 0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fw
ds3000_firmware_ondemand: Waiting for firmware upload(2)...
ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)
ds3000_tune: Unable initialise the firmware

Apparently it can't locate a firmware file, yet :

# ls -l  /lib/firmware/
-rwxr-xr-x    1 root     root         8192 May  3 07:09 dvb-fe-ds3000.fw

Any ideas why this happens?

Thanks and best regards,

Hamza Ferrag

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#2 lore raw

Hi Hans,

Quoted 11 lines · Hans Houwaard

I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.

The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.

Quoted 99 lines

Good luck,

Hans

Op 13-07-10 20:28, Hamza Ferrag schreef:

Quoted 92 lines

Hi all,

I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.

My configuration is :

- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last<http://mercurial.intuxication.org/hg/s2-liplianin%29last>changes at 05/29/2010,

All work fine i.e drivers/firmware installation after madprobe a right modules.

# lsmod
Module                  Size  Used by    Not tainted
cx23885                82416  0
tveeprom                9348  1 cx23885
btcx_risc               1928  1 cx23885
cx2341x                 7748  1 cx23885
ir_common              23936  1 cx23885
videobuf_dma_sg         5060  1 cx23885
ir_core                 3596  2 cx23885,ir_common
v4l2_common             8896  2 cx23885,cx2341x
videodev               25376  2 cx23885,v4l2_common
videobuf_dvb            2820  1 cx23885
videobuf_core           8388  3 cx23885,videobuf_dma_sg,videobuf_dvb
lnbp21                  1024  0
dvb_core               54832  2 cx23885,videobuf_dvb
ds3000                  9668  1
# dmesg
Linux video capture interface: v2.00
cx23885 driver version 0.0.2 loaded
CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470
[card=15,autodetected]
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
DS3000 chip version: 0.192 attached.
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (Montage Technology
DS3000/TS2020)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio:
0xdf800000
cx23885 0000:03:00.0: setting latency timer to 64
tun: Universal TUN/TAP device driver, 1.6

A problem appear when tunning card using szap-s2 :

# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyCh

reading channels from file '/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35
vpid 0x0286, apid 0x1fff, sid 0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fw
ds3000_firmware_ondemand: Waiting for firmware upload(2)...
ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)
ds3000_tune: Unable initialise the firmware

Apparently it can't locate a firmware file, yet :

# ls -l  /lib/firmware/
-rwxr-xr-x    1 root     root         8192 May  3 07:09 dvb-fe-ds3000.fw

Any ideas why this happens?

Thanks and best regards,

Hamza Ferrag

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#3 lore raw

Hi Hans,

Thanks for your quick feedback.

Any other suggestions guys ? .

Thanks in advance.

Hamza Ferrag.

Quoted 4 lines · ferrag hamza

Hi Hans,

Quoted 113 lines
Quoted 110 lines · Hans Houwaard

I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.

The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.

Good luck,

Hans

Op 13-07-10 20:28, Hamza Ferrag schreef:

Quoted 92 lines

Hi all,

I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.

My configuration is :

- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last<http://mercurial.intuxication.org/hg/s2-liplianin%29last>changes at 05/29/2010,

All work fine i.e drivers/firmware installation after madprobe a right modules.

# lsmod
Module                  Size  Used by    Not tainted
cx23885                82416  0
tveeprom                9348  1 cx23885
btcx_risc               1928  1 cx23885
cx2341x                 7748  1 cx23885
ir_common              23936  1 cx23885
videobuf_dma_sg         5060  1 cx23885
ir_core                 3596  2 cx23885,ir_common
v4l2_common             8896  2 cx23885,cx2341x
videodev               25376  2 cx23885,v4l2_common
videobuf_dvb            2820  1 cx23885
videobuf_core           8388  3 cx23885,videobuf_dma_sg,videobuf_dvb
lnbp21                  1024  0
dvb_core               54832  2 cx23885,videobuf_dvb
ds3000                  9668  1
# dmesg
Linux video capture interface: v2.00
cx23885 driver version 0.0.2 loaded
CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470
[card=15,autodetected]
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
DS3000 chip version: 0.192 attached.
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (Montage Technology
DS3000/TS2020)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0, mmio:
0xdf800000
cx23885 0000:03:00.0: setting latency timer to 64
tun: Universal TUN/TAP device driver, 1.6

A problem appear when tunning card using szap-s2 :

# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyCh

reading channels from file '/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35
vpid 0x0286, apid 0x1fff, sid 0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fw
ds3000_firmware_ondemand: Waiting for firmware upload(2)...
ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)
ds3000_tune: Unable initialise the firmware

Apparently it can't locate a firmware file, yet :

# ls -l  /lib/firmware/
-rwxr-xr-x    1 root     root         8192 May  3 07:09 dvb-fe-ds3000.fw

Any ideas why this happens?

Thanks and best regards,

Hamza Ferrag

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#7 lore raw
In reply to Hans Houwaard

Hi Hans,

Thanks for your quick feedback.

Any other suggestions guys ? .

Thanks in advance.

Hamza Ferrag.

Quoted 109 lines · Hans Houwaard

I don't really know why, but it happens sometimes on my machine with the same card as well. When I have problems, I power off the computer and then restart it again. The card will not properly load or function untill I do. There is probably some hardware lock that needs to be reset by powering off the card.

The loading of the firmware sometimes takes a couple of seconds in my machine, it's not very fast. Besides check if the card, which is on a PCI-1x slot, doesn't share an IRQ with the onboard soundcard. That will seriously effect the performance of both the card and the sound.

Good luck,

Hans

Op 13-07-10 20:28, Hamza Ferrag schreef:

Quoted 92 lines

Hi all,

I am trying to install a 'Tevii S470' card from TeVii technology as described here http://linuxtv.org/wiki/index.php/TeVii_S470.

My configuration is :

- intel x86 platform
- Kernel 2.6.27-21
- tevii_ds3000.tar.gz (firmware archive from
http://tevii.com/tevii_ds3000.tar.gz ),
- s2-liplianin mercurial sources ( from
http://mercurial.intuxication.org/hg/s2-liplianin)last changes at 05/29/2010,

All work fine i.e drivers/firmware installation after madprobe a right modules.

# lsmod
Module Size Used by Not tainted
cx23885 82416 0
tveeprom 9348 1 cx23885
btcx_risc 1928 1 cx23885
cx2341x 7748 1 cx23885
ir_common 23936 1 cx23885
videobuf_dma_sg 5060 1 cx23885
ir_core 3596 2 cx23885,ir_common
v4l2_common 8896 2 cx23885,cx2341x
videodev 25376 2 cx23885,v4l2_common
videobuf_dvb 2820 1 cx23885
videobuf_core 8388 3 cx23885,videobuf_dma_sg,videobuf_dvb
lnbp21 1024 0
dvb_core 54832 2 cx23885,videobuf_dvb
ds3000 9668 1
# dmesg
Linux video capture interface: v2.00
cx23885 driver version 0.0.2 loaded
CORE cx23885[0]: subsystem: d470:9022, board: TeVii S470
[card=15,autodetected]
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
DS3000 chip version: 0.192 attached.
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (Montage Technology
DS3000/TS2020)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:03:00.0, rev: 2, irq: 11, latency: 0,
mmio: 0xdf800000
cx23885 0000:03:00.0: setting latency timer to 64
tun: Universal TUN/TAP device driver, 1.6

A problem appear when tunning card using szap-s2 :

# szap-s2 szap-s2 -c /root/channels.conf -x -M 5 -C 89 -l 9750 -S 1 MyCh

reading channels from file '/root/channels.conf'
zapping to 1 'MyCh':
delivery DVB-S2, modulation 8PSK
sat 0, frequency 8420 MHz V, symbolrate 29400000, coderate 8/9,rolloff 0.35
vpid 0x0286, apid 0x1fff, sid 0x0000
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
firmware: requesting dvb-fe-ds3000.fw
ds3000_firmware_ondemand: Waiting for firmware upload(2)...
ds3000_firmware_ondemand: No firmware uploaded (timeout or file not found?)
ds3000_tune: Unable initialise the firmware

Apparently it can't locate a firmware file, yet :

# ls -l /lib/firmware/
-rwxr-xr-x 1 root root 8192 May 3 07:09 dvb-fe-ds3000.fw

Any ideas why this happens?

Thanks and best regards,

Hamza Ferrag

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#4 lore raw

TeVii S470 periodically fails to tune/lock - needs poweroff

In reply to ferrag hamza

Hello Guys,

I have been using my TeVii S470 DVBS2 card for about one month . I am using it with mythtv on fedora 12 using latest kernel , and compiled the latest v4l drivers . The sensitivity and picture is very good both on dvbs and dvbs2 transponders , very happy with that . However several times already when trying to watch live tv on myth the channel failed to tune . Usually happens in the morning after box was running 24x7 for a few days . The only way to restore functionality is to do a power off and wait a couple of mins then power on . If I just do a reboot , this does not help . Strange thing is that I see nothing unusual in the mythtv logs or dmesg/messages log . When the card is in this no-lock state , it will not tune into any transponder even when I run scandvb . After power reset everything works again for a few more days . Any info welcome .

Best Regards

Milorad

#5 lore raw

Re: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff

Check the temperature of the adapter. It is getting quite hot. I use fans to cool it, which avoids this kind of problems.

--------------------------------------------------
From: "O&M Ugarcina" <[email protected]>
Sent: Friday, September 03, 2010 10:42 AM
To: <[email protected]>
Cc: <[email protected]>
Subject: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff

Quoted 14 lines

Hello Guys,

I have been using my TeVii S470 DVBS2 card for about one month . I am using it with mythtv on fedora 12 using latest kernel , and compiled the latest v4l drivers . The sensitivity and picture is very good both on dvbs and dvbs2 transponders , very happy with that . However several times already when trying to watch live tv on myth the channel failed to tune . Usually happens in the morning after box was running 24x7 for a few days . The only way to restore functionality is to do a power off and wait a couple of mins then power on . If I just do a reboot , this does not help . Strange thing is that I see nothing unusual in the mythtv logs or dmesg/messages log . When the card is in this no-lock state , it will not tune into any transponder even when I run scandvb . After power reset everything works again for a few more days . Any info welcome .

Best Regards

Milorad

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#6 lore raw

Re: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff

Thanks for that Karsten,

I have checked the temperature and seems normal . It does not look like it is getting overly hot . I have been keeping a close eye on it and it looks like I get more failures when using Diseqc . I notice when going to another satellite then coming back I seem to get more no-locks . My suspicion is that there may be some issues with diseqc function that will crash the card . After a full power down is done card is back in operation with no problems . Could this be a firmware thing ?

Best Regards
Milorad

Quoted 39 lines · Karsten Siebert

Check the temperature of the adapter. It is getting quite hot. I use fans to cool it, which avoids this kind of problems.

--------------------------------------------------
From: "O&M Ugarcina" <[email protected]>
Sent: Friday, September 03, 2010 10:42 AM
To: <[email protected]>
Cc: <[email protected]>
Subject: [linux-dvb] TeVii S470 periodically fails to tune/lock - needspoweroff

Quoted 25 lines

 Hello Guys,

I have been using my TeVii S470 DVBS2 card for about one month . I am using it with mythtv on fedora 12 using latest kernel , and compiled the latest v4l drivers . The sensitivity and picture is very good both on dvbs and dvbs2 transponders , very happy with that . However several times already when trying to watch live tv on myth the channel failed to tune . Usually happens in the morning after box was running 24x7 for a few days . The only way to restore functionality is to do a power off and wait a couple of mins then power on . If I just do a reboot , this does not help . Strange thing is that I see nothing unusual in the mythtv logs or dmesg/messages log . When the card is in this no-lock state , it will not tune into any transponder even when I run scandvb . After power reset everything works again for a few more days . Any info welcome .

Best Regards

Milorad

_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb