Support for ns2501 DVO chip
Subsystems (2)
PATCH 1/1 Support for ns2501 DVO chip
Hi folks,
trying to get an old Fujitsu Siemens Laptop to work, I hacked up the NS2501 support provided by Gilles earlier. This patch provides simple DPMS support and includes some experimental support for the undocumented ns2501 scaler. I just copied the values the video bios left behind - and it works for me right now.
Problem with this specific chip is that it is not always on the i2c bus - if it doesn't like the screen resolution or the pipe A PLL isn't on, it is deaf and blind. Thus, this patch includes a hack to force-on the DVO on the bus to push the new scaler values into it. Probably there is a smarter way to do the same, a way that breaks the architecture less than what it does now, but at least the beast is now tamed and working.
Here is the patch:
/* snip */
drivers/gpu/drm/i915/dvo.h 2012-06-08 13:15:19.000000000 +0200 renamed from drivers/gpu/drm/i915/dvo.h 2012-06-01 09:18:44.000000000 +0200 +1 -0
@@ -140,5 +140,6 @@ extern struct intel_dvo_dev_ops ch7xxx_o extern struct intel_dvo_dev_ops ivch_ops; extern struct intel_dvo_dev_ops tfp410_ops; extern struct intel_dvo_dev_ops ch7017_ops; +extern struct intel_dvo_dev_ops ns2501_ops; #endif /* _INTEL_DVO_H */
drivers/gpu/drm/i915/dvo_ns2501.c 2012-06-08 17:52:21.000000000 +0200 renamed from drivers/gpu/drm/i915/dvo_ns2501.c 2012-06-08 17:59:20.000000000 +0200 +1 -0
@@ -0,0 +1,544 @@ +/**************************************************************************
+
+Copyright © 2012 Gilles Dartiguelongue, Thomas Richter
+
+All Rights Reserved.
+
+Permission is hereby granted, free of charge, to any person obtaining a +copy of this software and associated documentation files (the +"Software"), to deal in the Software without restriction, including +without limitation the rights to use, copy, modify, merge, publish, +distribute, sub license, and/or sell copies of the Software, and to +permit persons to whom the Software is furnished to do so, subject to +the following conditions:
+
+The above copyright notice and this permission notice (including the +next paragraph) shall be included in all copies or substantial portions +of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS +OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. +IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, +TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE +SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ +**************************************************************************/
+
+#include "dvo.h"
+#include "i915_reg.h"
+#include "i915_drv.h"
+
+#define NS2501_VID 0x1305
+#define NS2501_DID 0x6726
+
+#define NS2501_VID_LO 0x00
+#define NS2501_VID_HI 0x01
+#define NS2501_DID_LO 0x02
+#define NS2501_DID_HI 0x03
+#define NS2501_REV 0x04
+#define NS2501_RSVD 0x05
+#define NS2501_FREQ_LO 0x06
+#define NS2501_FREQ_HI 0x07
+
+#define NS2501_REG8 0x08
+#define NS2501_8_VEN (1<<5)
+#define NS2501_8_HEN (1<<4)
+#define NS2501_8_DSEL (1<<3)
+#define NS2501_8_BPAS (1<<2)
+#define NS2501_8_RSVD (1<<1)
+#define NS2501_8_PD (1<<0)
+
+#define NS2501_REG9 0x09
+#define NS2501_9_VLOW (1<<7)
+#define NS2501_9_MSEL_MASK (0x7<<4)
+#define NS2501_9_TSEL (1<<3)
+#define NS2501_9_RSEN (1<<2)
+#define NS2501_9_RSVD (1<<1)
+#define NS2501_9_MDI (1<<0)
+
+#define NS2501_REGC 0x0c
+
+struct ns2501_priv {
+ //I2CDevRec d; + bool quiet; + int reg_8_shadow; + int reg_8_set; + // Shadow registers for i915 + int dvoc; + int pll_a; + int srcdim; + int fw_blc;
+};
+
+#define NSPTR(d) ((NS2501Ptr)(d->DriverPrivate.ptr))
+
+/*
+** Include the PLL launcher prototype
+*/
+extern void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe); +
+/*
+** For reasons unclear to me, the ns2501 at least on the Fujitsu/Siemens +** laptops does not react on the i2c bus unless
+** both the PLL is running and the display is configured in its native +** resolution.
+** This function forces the DVO on, and stores the registers it touches. +** Afterwards, registers are restored to regular values.
+**
+** This is pretty much a hack, though it works.
+** Without that, ns2501_readb and ns2501_writeb fail
+** when switching the resolution.
+*/
+
+static void enable_dvo(struct intel_dvo_device *dvo)
+{
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv); + struct i2c_adapter *adapter = dvo->i2c_bus; + struct intel_gmbus *bus = container_of(adapter,
+ struct intel_gmbus,
+ adapter);
+ struct drm_i915_private *dev_priv = bus->dev_priv;
+
+ DRM_DEBUG_KMS("%s: Trying to re-enable the DVO\n",__FUNCTION__); +
+ ns->dvoc = I915_READ(DVO_C); + ns->pll_a = I915_READ(_DPLL_A); + ns->srcdim = I915_READ(DVOC_SRCDIM); + ns->fw_blc = I915_READ(FW_BLC); + + I915_WRITE(DVOC, 0x10004084); + I915_WRITE(_DPLL_A,0xd0820000); + I915_WRITE(DVOC_SRCDIM,0x400300); // 1024x768 + I915_WRITE(FW_BLC,0x1080304);
+
+ intel_enable_pll(dev_priv,0);
+
+ I915_WRITE(DVOC, 0x90004084);
+}
+
+/*
+** Restore the I915 registers modified by the above +** trigger function.
+*/
+static void restore_dvo(struct intel_dvo_device *dvo) +{
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_gmbus *bus = container_of(adapter,
+ struct intel_gmbus,
+ adapter);
+ struct drm_i915_private *dev_priv = bus->dev_priv;
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv); +
+ I915_WRITE(DVOC ,ns->dvoc); + I915_WRITE(_DPLL_A ,ns->pll_a); + I915_WRITE(DVOC_SRCDIM,ns->srcdim); + I915_WRITE(FW_BLC ,ns->fw_blc);
+}
+
+/*
+** Read a register from the ns2501.
+** Returns true if successful, false otherwise.
+** If it returns false, it might be wise to enable the
+** DVO with the above function.
+*/
+static bool ns2501_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch) +{
+ struct ns2501_priv *ns = dvo->dev_priv;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ u8 out_buf[2];
+ u8 in_buf[2];
+
+ struct i2c_msg msgs[] = {
+ {
+ .addr = dvo->slave_addr,
+ .flags = 0,
+ .len = 1,
+ .buf = out_buf,
+ },
+ {
+ .addr = dvo->slave_addr,
+ .flags = I2C_M_RD,
+ .len = 1,
+ .buf = in_buf,+ }
+ };
+
+ out_buf[0] = addr;
+ out_buf[1] = 0;
+
+ if (i2c_transfer(adapter, msgs, 2) == 2) {
+ *ch = in_buf[0];
+ return true;
+ };
+
+ if (!ns->quiet) {
+ DRM_DEBUG_KMS("Unable to read register 0x%02x from %s:0x%02x.\n",
+ addr, adapter->name, dvo->slave_addr);
+ }
+
+ return false;
+}
+
+/*
+** Write a register to the ns2501.
+** Returns true if successful, false otherwise.
+** If it returns false, it might be wise to enable the
+** DVO with the above function.
+*/
+static bool ns2501_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch) +{
+ struct ns2501_priv *ns = dvo->dev_priv;
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ uint8_t out_buf[2];
+
+ struct i2c_msg msg = {
+ .addr = dvo->slave_addr,
+ .flags = 0,
+ .len = 2,
+ .buf = out_buf,+ };
+
+ out_buf[0] = addr;
+ out_buf[1] = ch;
+
+ if (i2c_transfer(adapter, &msg, 1) == 1) {
+ return true;
+ }
+
+ if (!ns->quiet) {
+ DRM_DEBUG_KMS("Unable to write register 0x%02x to %s:%d\n",
+ addr, adapter->name, dvo->slave_addr);
+ }
+
+ return false;
+}
+
+/* National Semiconductor 2501 driver for chip on i2c bus +** scan for the chip on the bus.
+** Hope the VBIOS initialized the PLL correctly so we can +** talk to it. If not, it will not be seen and not detected. +** Bummer!
+*/
+static bool ns2501_init(struct intel_dvo_device *dvo,
+ struct i2c_adapter *adapter)
+{
+ /* this will detect the NS2501 chip on the specified i2c bus */ + struct ns2501_priv *ns; + unsigned char ch;
+
+ ns = kzalloc(sizeof(struct ns2501_priv), GFP_KERNEL);
+ if (ns == NULL)
+ return false;
+
+ dvo->i2c_bus = adapter; + dvo->dev_priv = ns; + ns->quiet = true;
+
+ if (!ns2501_readb(dvo, NS2501_VID_LO, &ch))
+ goto out;
+
+ if (ch != (NS2501_VID & 0xff)) {
+ DRM_DEBUG_KMS("ns2501 not detected got %d: from %s Slave %d.\n",
+ ch, adapter->name, dvo->slave_addr);
+ goto out;
+ }
+
+ if (!ns2501_readb(dvo, NS2501_DID_LO, &ch))
+ goto out;
+
+ if (ch != (NS2501_DID & 0xff)) {
+ DRM_DEBUG_KMS("ns2501 not detected got %d: from %s Slave %d.\n",
+ ch, adapter->name, dvo->slave_addr);
+ goto out;
+ } + ns->quiet = false; + ns->reg_8_set = 0; + ns->reg_8_shadow = NS2501_8_PD | NS2501_8_BPAS | NS2501_8_VEN | NS2501_8_HEN;
+
+ DRM_DEBUG_KMS("init ns2501 dvo controller successfully!\n");
+ return true;
+
+ out:
+ kfree(ns);
+ return false;
+}
+
+static enum drm_connector_status ns2501_detect(struct intel_dvo_device *dvo) +{
+ /* + ** This is a Laptop display, it doesn't have hotplugging. + ** Even if not, the detection bit of the 2501 is unreliable as + ** it only works for some display types. + ** It is even more unreliable as the PLL must be active for + ** allowing reading from the chiop. + */ + return connector_status_connected;
+}
+
+static enum drm_mode_status ns2501_mode_valid(struct intel_dvo_device *dvo,
+ struct drm_display_mode *mode)
+{
+ DRM_DEBUG_KMS("%s: is mode valid (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d)\n",__FUNCTION__,
+ mode->hdisplay,mode->htotal,mode->vdisplay,mode->vtotal);
+
+
+ /* + ** Currently, these are all the modes I have data from. + ** More might exist. Unclear how to find the native resolution + ** of the panel in here so we could always accept it + ** by disabling the scaler. + */ + if ((mode->hdisplay == 800 && mode->vdisplay == 600) ||
+ (mode->hdisplay == 640 && mode->vdisplay == 480) ||
+ (mode->hdisplay == 1024 && mode->vdisplay == 768)) {
+ return MODE_OK;
+ } else {
+ return MODE_ONE_SIZE; /* Is this a reasonable error? */
+ }
+}
+
+static void ns2501_mode_set(struct intel_dvo_device *dvo,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
+
+ DRM_DEBUG_KMS("%s: set mode (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d).\n",__FUNCTION__,
+ mode->hdisplay,mode->htotal,mode->vdisplay,mode->vtotal);
+
+ /*
+ ** Where do I find the native resolution for which scaling is not required???
+ **
+ ** First trigger the DVO on as otherwise the chip does not appear on the i2c
+ ** bus.
+ */
+ enable_dvo(dvo);
+
+ if (mode->hdisplay == 800 && mode->vdisplay == 600) {
+ /* mode 277 */
+ ns->reg_8_shadow &= ~NS2501_8_BPAS;
+ DRM_DEBUG_KMS("%s: switching to 800x600\n",__FUNCTION__);
+
+ /*
+ ** No, I do not know where this data comes from.
+ ** It is just what the video bios left in the DVO, so
+ ** I'm just copying it here over.
+ ** This also means that I cannot support any other modes
+ ** except the ones supported by the bios.
+ */
+ ns2501_writeb(dvo, 0x11, 0xc8);
+ ns2501_writeb(dvo, 0x1b, 0x19);
+ ns2501_writeb(dvo, 0x1c, 0x64);
+ ns2501_writeb(dvo, 0x1d, 0x02);+
+ ns2501_writeb(dvo, 0x34, 0x03);
+ ns2501_writeb(dvo, 0x35, 0xff);
+
+ ns2501_writeb(dvo, 0x80, 0x27); + ns2501_writeb(dvo, 0x81, 0x03); + ns2501_writeb(dvo, 0x82, 0x41); + ns2501_writeb(dvo, 0x83, 0x05); + + ns2501_writeb(dvo, 0x8d, 0x02); + ns2501_writeb(dvo, 0x8e, 0x04); + ns2501_writeb(dvo, 0x8f, 0x00); + + ns2501_writeb(dvo, 0x90, 0xff); /* vertical */ + ns2501_writeb(dvo, 0x91, 0x07); + ns2501_writeb(dvo, 0x94, 0x00); + ns2501_writeb(dvo, 0x95, 0x00);
+
+ ns2501_writeb(dvo, 0x96, 0x00);
+
+ ns2501_writeb(dvo, 0x99, 0x00);
+ ns2501_writeb(dvo, 0x9a, 0x88);
+
+ ns2501_writeb(dvo, 0x9c, 0x23); + ns2501_writeb(dvo, 0x9d, 0x00); + ns2501_writeb(dvo, 0x9e, 0x25); + ns2501_writeb(dvo, 0x9f, 0x03);
+
+ ns2501_writeb(dvo, 0xa4, 0x80);
+
+ ns2501_writeb(dvo, 0xb6, 0x00);
+
+ ns2501_writeb(dvo, 0xb9, 0xc8); /* horizontal? */
+ ns2501_writeb(dvo, 0xba, 0x00); /* horizontal? */
+
+ ns2501_writeb(dvo, 0xc0, 0x05); /* horizontal? */
+ ns2501_writeb(dvo, 0xc1, 0xd7);
+
+ ns2501_writeb(dvo, 0xc2, 0x00);
+ ns2501_writeb(dvo, 0xc3, 0xf8);
+
+ ns2501_writeb(dvo, 0xc4, 0x03);
+ ns2501_writeb(dvo, 0xc5, 0x1a);
+
+ ns2501_writeb(dvo, 0xc6, 0x00);
+ ns2501_writeb(dvo, 0xc7, 0x73);
+ ns2501_writeb(dvo, 0xc8, 0x02);
+
+ } else if (mode->hdisplay == 640 && mode->vdisplay == 480) {
+ /* mode 274 */
+ DRM_DEBUG_KMS("%s: switching to 640x480\n",__FUNCTION__);
+ /*
+ ** No, I do not know where this data comes from.
+ ** It is just what the video bios left in the DVO, so
+ ** I'm just copying it here over.
+ ** This also means that I cannot support any other modes
+ ** except the ones supported by the bios.
+ */
+ ns->reg_8_shadow &= ~NS2501_8_BPAS;
+
+ ns2501_writeb(dvo, 0x11, 0xa0);
+ ns2501_writeb(dvo, 0x1b, 0x11);
+ ns2501_writeb(dvo, 0x1c, 0x54);
+ ns2501_writeb(dvo, 0x1d, 0x03);+
+ ns2501_writeb(dvo, 0x34, 0x03);
+ ns2501_writeb(dvo, 0x35, 0xff);
+
+ ns2501_writeb(dvo, 0x80, 0xff); + ns2501_writeb(dvo, 0x81, 0x07); + ns2501_writeb(dvo, 0x82, 0x3d); + ns2501_writeb(dvo, 0x83, 0x05); + + ns2501_writeb(dvo, 0x8d, 0x02); + ns2501_writeb(dvo, 0x8e, 0x10); + ns2501_writeb(dvo, 0x8f, 0x00); + + ns2501_writeb(dvo, 0x90, 0xff); /* vertical */ + ns2501_writeb(dvo, 0x91, 0x07); + ns2501_writeb(dvo, 0x94, 0x00); + ns2501_writeb(dvo, 0x95, 0x00);
+
+ ns2501_writeb(dvo, 0x96, 0x05);
+
+ ns2501_writeb(dvo, 0x99, 0x00);
+ ns2501_writeb(dvo, 0x9a, 0x88);
+
+ ns2501_writeb(dvo, 0x9c, 0x24); + ns2501_writeb(dvo, 0x9d, 0x00); + ns2501_writeb(dvo, 0x9e, 0x25); + ns2501_writeb(dvo, 0x9f, 0x03);
+
+ ns2501_writeb(dvo, 0xa4, 0x84);
+
+ ns2501_writeb(dvo, 0xb6, 0x09);
+
+ ns2501_writeb(dvo, 0xb9, 0xa0); /* horizontal? */
+ ns2501_writeb(dvo, 0xba, 0x00); /* horizontal? */
+
+ ns2501_writeb(dvo, 0xc0, 0x05); /* horizontal? */
+ ns2501_writeb(dvo, 0xc1, 0x90);
+
+ ns2501_writeb(dvo, 0xc2, 0x00);
+ ns2501_writeb(dvo, 0xc3, 0x0f);
+
+ ns2501_writeb(dvo, 0xc4, 0x03);
+ ns2501_writeb(dvo, 0xc5, 0x16);
+
+ ns2501_writeb(dvo, 0xc6, 0x00);
+ ns2501_writeb(dvo, 0xc7, 0x02);
+ ns2501_writeb(dvo, 0xc8, 0x02);
+
+ } else if (mode->hdisplay == 1024 && mode->vdisplay == 768) {
+ /* mode 280 */
+ DRM_DEBUG_KMS("%s: switching to 1024x768\n",__FUNCTION__);
+ /*
+ ** This might or might not work, actually. I'm silently
+ ** assuming here that the native panel resolution is
+ ** 1024x768. If not, then this leaves the scaler disabled
+ ** generating a picture that is likely not the expected.
+ **
+ ** Problem is that I do not know where to take the panel
+ ** dimensions from.
+ **
+ ** Enable the bypass, scaling not required.
+ **
+ ** The scaler registers are irrelevant here....
+ **
+ */
+ ns->reg_8_shadow |= NS2501_8_BPAS;
+ ns2501_writeb(dvo, 0x37, 0x44);
+ } else {
+ /* Data not known. Bummer!
+ ** Hopefully, the code should not go here
+ ** as mode_OK delivered no other modes.
+ */
+ ns->reg_8_shadow |= NS2501_8_BPAS;
+ }
+ ns2501_writeb(dvo, NS2501_REG8, ns->reg_8_shadow);
+
+ /*
+ ** Restore the old i915 registers before
+ ** forcing the ns2501 on.
+ */
+ restore_dvo(dvo);+}
+
+/* set the NS2501 power state */
+static void ns2501_dpms(struct intel_dvo_device *dvo, int mode)
+{
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
+ unsigned char ch;
+
+ DRM_DEBUG_KMS("%s: Trying set the dpms of the DVO to %d\n",__FUNCTION__,mode); +
+ ch = ns->reg_8_shadow;
+
+ if (mode == DRM_MODE_DPMS_ON)
+ ch |= NS2501_8_PD;
+ else
+ ch &= ~NS2501_8_PD;
+
+ if (ns->reg_8_set == 0 || ns->reg_8_shadow != ch) {
+ ns->reg_8_set = 1; + ns->reg_8_shadow = ch; + ns2501_writeb(dvo, NS2501_REG8, ch); + } + /* + ** Note that this may actually fail,namely exactly + ** when the chip vanished from the bus. + ** + ** Should I force-enable it here?? + */
+}
+
+static void ns2501_dump_regs(struct intel_dvo_device *dvo) +{
+ uint8_t val;
+
+ ns2501_readb(dvo, NS2501_FREQ_LO, &val);
+ DRM_LOG_KMS("NS2501_FREQ_LO: 0x%02x\n", val);
+ ns2501_readb(dvo, NS2501_FREQ_HI, &val);
+ DRM_LOG_KMS("NS2501_FREQ_HI: 0x%02x\n", val);
+ ns2501_readb(dvo, NS2501_REG8, &val);
+ DRM_LOG_KMS("NS2501_REG8: 0x%02x\n", val);
+ ns2501_readb(dvo, NS2501_REG9, &val);
+ DRM_LOG_KMS("NS2501_REG9: 0x%02x\n", val);
+ ns2501_readb(dvo, NS2501_REGC, &val);
+ DRM_LOG_KMS("NS2501_REGC: 0x%02x\n", val);+}
+
+static void ns2501_destroy(struct intel_dvo_device *dvo) +{
+ struct ns2501_priv *ns = dvo->dev_priv;
+
+ if (ns) {
+ kfree(ns);
+ dvo->dev_priv = NULL;
+ }
+}
+
+struct intel_dvo_dev_ops ns2501_ops = {
+ .init = ns2501_init, + .detect = ns2501_detect, + .mode_valid = ns2501_mode_valid, + .mode_set = ns2501_mode_set, + .dpms = ns2501_dpms, + .dump_regs = ns2501_dump_regs, + .destroy = ns2501_destroy,
+};
drivers/gpu/drm/i915/intel_display.c 2012-06-08 16:55:20.000000000 +0200 renamed from drivers/gpu/drm/i915/intel_display.c 2012-06-01 09:18:44.000000000 +0200 +1 -1
@@ -1142,7 +1142,7 @@ static void assert_pch_ports_disabled(st * * Note! This is for pre-ILK only. */ -static void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe) +void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe) { int reg; u32 val;
drivers/gpu/drm/i915/intel_dvo.c 2012-06-08 12:50:16.000000000 +0200 renamed from drivers/gpu/drm/i915/intel_dvo.c 2012-06-01 09:18:44.000000000 +0200 +8 -0
@@ -37,6 +37,7 @@ #define SIL164_ADDR 0x38 #define CH7xxx_ADDR 0x76 #define TFP410_ADDR 0x38 +#define NS2501_ADDR 0x38 static const struct intel_dvo_device intel_dvo_devices[] = { {
@@ -61,6 +62,13 @@ static const struct intel_dvo_device int .dev_ops = &ivch_ops, }, { + .type = INTEL_DVO_CHIP_TMDS, + .name = "ns2501", + .dvo_reg = DVOC, + .slave_addr = NS2501_ADDR, + .dev_ops = &ns2501_ops, + }, + { .type = INTEL_DVO_CHIP_TMDS, .name = "tfp410", .dvo_reg = DVOC,
drivers/gpu/drm/i915/Makefile 2012-06-08 12:50:54.000000000 +0200 renamed from drivers/gpu/drm/i915/Makefile 2012-06-01 09:18:44.000000000 +0200 +2 -1
@@ -34,7 +34,8 @@ i915-y := i915_drv.o i915_dma.o i915_irq dvo_ch7017.o \ dvo_ivch.o \ dvo_tfp410.o \ - dvo_sil164.o + dvo_sil164.o \ + dvo_ns2501.o i915-$(CONFIG_COMPAT) += i915_ioc32.o
/* snip */
Please check and confirm to which degree this is working.
Thanks,
Thomas