Skip to contentSkip to conversation

Support for ns2501 DVO chip

PATCH New Thomas Richter 1 participant 1 message Jun 8, 2012

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Support for ns2501 DVO chip

Hi folks,

trying to get an old Fujitsu Siemens Laptop to work, I hacked up the NS2501 support provided by Gilles earlier. This patch provides simple DPMS support and includes some experimental support for the undocumented ns2501 scaler. I just copied the values the video bios left behind - and it works for me right now.

Problem with this specific chip is that it is not always on the i2c bus - if it doesn't like the screen resolution or the pipe A PLL isn't on, it is deaf and blind. Thus, this patch includes a hack to force-on the DVO on the bus to push the new scaler values into it. Probably there is a smarter way to do the same, a way that breaks the architecture less than what it does now, but at least the beast is now tamed and working.

Here is the patch:

/* snip */

drivers/gpu/drm/i915/dvo.h 2012-06-08 13:15:19.000000000 +0200 renamed from drivers/gpu/drm/i915/dvo.h 2012-06-01 09:18:44.000000000 +0200 +1 -0
diff -rup linux-3.4.1-orig/drivers/gpu/drm/i915/dvo.h linux-3.4.1/drivers/gpu/drm/i915/dvo.h
@@ -140,5 +140,6 @@ extern struct intel_dvo_dev_ops ch7xxx_o
 extern struct intel_dvo_dev_ops ivch_ops;
 extern struct intel_dvo_dev_ops tfp410_ops;
 extern struct intel_dvo_dev_ops ch7017_ops;
+extern struct intel_dvo_dev_ops ns2501_ops;
 
 #endif /* _INTEL_DVO_H */
drivers/gpu/drm/i915/dvo_ns2501.c 2012-06-08 17:52:21.000000000 +0200 renamed from drivers/gpu/drm/i915/dvo_ns2501.c 2012-06-08 17:59:20.000000000 +0200 +1 -0
diff -rup linux-3.4.1-orig/drivers/gpu/drm/i915/dvo_ns2501.c linux-3.4.1/drivers/gpu/drm/i915/dvo_ns2501.c
@@ -0,0 +1,544 @@
+/************************************************************************** 

+
+Copyright © 2012 Gilles Dartiguelongue, Thomas Richter
+
+All Rights Reserved.
+
+Permission is hereby granted, free of charge, to any person obtaining a +copy of this software and associated documentation files (the +"Software"), to deal in the Software without restriction, including +without limitation the rights to use, copy, modify, merge, publish, +distribute, sub license, and/or sell copies of the Software, and to +permit persons to whom the Software is furnished to do so, subject to +the following conditions:
+
+The above copyright notice and this permission notice (including the +next paragraph) shall be included in all copies or substantial portions +of the Software.
+
+THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS +OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF +MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. +IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, +TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE +SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ +**************************************************************************/

+
+#include "dvo.h"
+#include "i915_reg.h"
+#include "i915_drv.h"
+
+#define NS2501_VID 0x1305
+#define NS2501_DID 0x6726
+
+#define NS2501_VID_LO 0x00
+#define NS2501_VID_HI 0x01
+#define NS2501_DID_LO 0x02
+#define NS2501_DID_HI 0x03
+#define NS2501_REV 0x04
+#define NS2501_RSVD 0x05
+#define NS2501_FREQ_LO 0x06
+#define NS2501_FREQ_HI 0x07
+
+#define NS2501_REG8 0x08
+#define NS2501_8_VEN (1<<5)
+#define NS2501_8_HEN (1<<4)
+#define NS2501_8_DSEL (1<<3)
+#define NS2501_8_BPAS (1<<2)
+#define NS2501_8_RSVD (1<<1)
+#define NS2501_8_PD (1<<0)
+
+#define NS2501_REG9 0x09
+#define NS2501_9_VLOW (1<<7)
+#define NS2501_9_MSEL_MASK (0x7<<4)
+#define NS2501_9_TSEL (1<<3)
+#define NS2501_9_RSEN (1<<2)
+#define NS2501_9_RSVD (1<<1)
+#define NS2501_9_MDI (1<<0)
+
+#define NS2501_REGC 0x0c
+
+struct ns2501_priv {

+  //I2CDevRec d;
+  bool quiet;
+  int reg_8_shadow;
+  int reg_8_set;
+  // Shadow registers for i915
+  int dvoc;
+  int pll_a;
+  int srcdim;
+  int fw_blc;

+};
+
+#define NSPTR(d) ((NS2501Ptr)(d->DriverPrivate.ptr))
+
+/*
+** Include the PLL launcher prototype
+*/
+extern void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe); +
+/*
+** For reasons unclear to me, the ns2501 at least on the Fujitsu/Siemens +** laptops does not react on the i2c bus unless
+** both the PLL is running and the display is configured in its native +** resolution.
+** This function forces the DVO on, and stores the registers it touches. +** Afterwards, registers are restored to regular values.
+**
+** This is pretty much a hack, though it works.
+** Without that, ns2501_readb and ns2501_writeb fail
+** when switching the resolution.
+*/
+
+static void enable_dvo(struct intel_dvo_device *dvo)
+{

+  struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
+  struct i2c_adapter *adapter = dvo->i2c_bus;
+  struct intel_gmbus *bus     = container_of(adapter,

+ struct intel_gmbus,
+ adapter);
+ struct drm_i915_private *dev_priv = bus->dev_priv;
+
+ DRM_DEBUG_KMS("%s: Trying to re-enable the DVO\n",__FUNCTION__); +

+  ns->dvoc   = I915_READ(DVO_C);
+  ns->pll_a  = I915_READ(_DPLL_A);
+  ns->srcdim = I915_READ(DVOC_SRCDIM);
+  ns->fw_blc = I915_READ(FW_BLC);
+
+  I915_WRITE(DVOC, 0x10004084);
+  I915_WRITE(_DPLL_A,0xd0820000);
+  I915_WRITE(DVOC_SRCDIM,0x400300); // 1024x768
+  I915_WRITE(FW_BLC,0x1080304);

+
+ intel_enable_pll(dev_priv,0);
+
+ I915_WRITE(DVOC, 0x90004084);
+}
+
+/*
+** Restore the I915 registers modified by the above +** trigger function.
+*/
+static void restore_dvo(struct intel_dvo_device *dvo) +{
+ struct i2c_adapter *adapter = dvo->i2c_bus;
+ struct intel_gmbus *bus = container_of(adapter,
+ struct intel_gmbus,
+ adapter);
+ struct drm_i915_private *dev_priv = bus->dev_priv;
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv); +

+  I915_WRITE(DVOC       ,ns->dvoc);
+  I915_WRITE(_DPLL_A    ,ns->pll_a);
+  I915_WRITE(DVOC_SRCDIM,ns->srcdim);
+  I915_WRITE(FW_BLC     ,ns->fw_blc);

+}
+
+/*
+** Read a register from the ns2501.
+** Returns true if successful, false otherwise.
+** If it returns false, it might be wise to enable the
+** DVO with the above function.
+*/
+static bool ns2501_readb(struct intel_dvo_device *dvo, int addr, uint8_t *ch) +{

+  struct ns2501_priv *ns = dvo->dev_priv;
+  struct i2c_adapter *adapter = dvo->i2c_bus;
+  u8 out_buf[2];
+  u8 in_buf[2];
+
+  struct i2c_msg msgs[] = {
+    {
+      .addr = dvo->slave_addr,
+      .flags = 0,
+      .len = 1,
+      .buf = out_buf,
+    },
+    {
+      .addr = dvo->slave_addr,
+      .flags = I2C_M_RD,
+      .len = 1,
+      .buf = in_buf,

+ }
+ };
+
+ out_buf[0] = addr;
+ out_buf[1] = 0;
+
+ if (i2c_transfer(adapter, msgs, 2) == 2) {
+ *ch = in_buf[0];
+ return true;
+ };
+
+ if (!ns->quiet) {
+ DRM_DEBUG_KMS("Unable to read register 0x%02x from %s:0x%02x.\n",
+ addr, adapter->name, dvo->slave_addr);
+ }
+
+ return false;
+}
+
+/*
+** Write a register to the ns2501.
+** Returns true if successful, false otherwise.
+** If it returns false, it might be wise to enable the
+** DVO with the above function.
+*/
+static bool ns2501_writeb(struct intel_dvo_device *dvo, int addr, uint8_t ch) +{

+  struct ns2501_priv *ns = dvo->dev_priv;
+  struct i2c_adapter *adapter = dvo->i2c_bus;
+  uint8_t out_buf[2];
+
+  struct i2c_msg msg = {
+    .addr = dvo->slave_addr,
+    .flags = 0,
+    .len = 2,
+    .buf = out_buf,

+ };
+
+ out_buf[0] = addr;
+ out_buf[1] = ch;
+
+ if (i2c_transfer(adapter, &msg, 1) == 1) {
+ return true;
+ }
+
+ if (!ns->quiet) {
+ DRM_DEBUG_KMS("Unable to write register 0x%02x to %s:%d\n",
+ addr, adapter->name, dvo->slave_addr);
+ }
+
+ return false;
+}
+
+/* National Semiconductor 2501 driver for chip on i2c bus +** scan for the chip on the bus.
+** Hope the VBIOS initialized the PLL correctly so we can +** talk to it. If not, it will not be seen and not detected. +** Bummer!
+*/
+static bool ns2501_init(struct intel_dvo_device *dvo,
+ struct i2c_adapter *adapter)
+{

+  /* this will detect the NS2501 chip on the specified i2c bus */
+  struct ns2501_priv *ns;
+  unsigned char ch;

+
+ ns = kzalloc(sizeof(struct ns2501_priv), GFP_KERNEL);
+ if (ns == NULL)
+ return false;
+

+  dvo->i2c_bus = adapter;
+  dvo->dev_priv = ns;
+  ns->quiet = true;

+
+ if (!ns2501_readb(dvo, NS2501_VID_LO, &ch))
+ goto out;
+
+ if (ch != (NS2501_VID & 0xff)) {
+ DRM_DEBUG_KMS("ns2501 not detected got %d: from %s Slave %d.\n",
+ ch, adapter->name, dvo->slave_addr);
+ goto out;
+ }
+
+ if (!ns2501_readb(dvo, NS2501_DID_LO, &ch))
+ goto out;
+
+ if (ch != (NS2501_DID & 0xff)) {
+ DRM_DEBUG_KMS("ns2501 not detected got %d: from %s Slave %d.\n",
+ ch, adapter->name, dvo->slave_addr);
+ goto out;

+  }
+  ns->quiet        = false;
+  ns->reg_8_set    = 0;
+  ns->reg_8_shadow = NS2501_8_PD | NS2501_8_BPAS | NS2501_8_VEN | NS2501_8_HEN;

+
+ DRM_DEBUG_KMS("init ns2501 dvo controller successfully!\n");
+ return true;
+
+ out:
+ kfree(ns);
+ return false;
+}
+
+static enum drm_connector_status ns2501_detect(struct intel_dvo_device *dvo) +{

+  /*
+  ** This is a Laptop display, it doesn't have hotplugging.
+  ** Even if not, the detection bit of the 2501 is unreliable as
+  ** it only works for some display types.
+  ** It is even more unreliable as the PLL must be active for
+  ** allowing reading from the chiop.
+  */
+  return connector_status_connected;

+}
+
+static enum drm_mode_status ns2501_mode_valid(struct intel_dvo_device *dvo,
+ struct drm_display_mode *mode)
+{
+ DRM_DEBUG_KMS("%s: is mode valid (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d)\n",__FUNCTION__,
+ mode->hdisplay,mode->htotal,mode->vdisplay,mode->vtotal);
+
+

+  /*
+  ** Currently, these are all the modes I have data from.
+  ** More might exist. Unclear how to find the native resolution
+  ** of the panel in here so we could always accept it
+  ** by disabling the scaler.
+  */
+  if ((mode->hdisplay == 800 && mode->vdisplay == 600) ||

+ (mode->hdisplay == 640 && mode->vdisplay == 480) ||
+ (mode->hdisplay == 1024 && mode->vdisplay == 768)) {
+ return MODE_OK;
+ } else {
+ return MODE_ONE_SIZE; /* Is this a reasonable error? */
+ }
+}
+
+static void ns2501_mode_set(struct intel_dvo_device *dvo,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
+
+ DRM_DEBUG_KMS("%s: set mode (hdisplay=%d,htotal=%d,vdisplay=%d,vtotal=%d).\n",__FUNCTION__,
+ mode->hdisplay,mode->htotal,mode->vdisplay,mode->vtotal);
+

+  /*
+  ** Where do I find the native resolution for which scaling is not required???
+  **
+  ** First trigger the DVO on as otherwise the chip does not appear on the i2c
+  ** bus.
+  */
+  enable_dvo(dvo);
+
+  if (mode->hdisplay == 800 && mode->vdisplay == 600) {
+    /* mode 277 */
+    ns->reg_8_shadow &= ~NS2501_8_BPAS;
+    DRM_DEBUG_KMS("%s: switching to 800x600\n",__FUNCTION__);
+
+    /*
+    ** No, I do not know where this data comes from.
+    ** It is just what the video bios left in the DVO, so
+    ** I'm just copying it here over.
+    ** This also means that I cannot support any other modes
+    ** except the ones supported by the bios.
+    */
+    ns2501_writeb(dvo, 0x11, 0xc8);
+    ns2501_writeb(dvo, 0x1b, 0x19);
+    ns2501_writeb(dvo, 0x1c, 0x64);
+    ns2501_writeb(dvo, 0x1d, 0x02);

+
+ ns2501_writeb(dvo, 0x34, 0x03);
+ ns2501_writeb(dvo, 0x35, 0xff);
+

+    ns2501_writeb(dvo, 0x80, 0x27);
+    ns2501_writeb(dvo, 0x81, 0x03);
+    ns2501_writeb(dvo, 0x82, 0x41);
+    ns2501_writeb(dvo, 0x83, 0x05);
+
+    ns2501_writeb(dvo, 0x8d, 0x02);
+    ns2501_writeb(dvo, 0x8e, 0x04);
+    ns2501_writeb(dvo, 0x8f, 0x00);
+
+    ns2501_writeb(dvo, 0x90, 0xff); /* vertical */
+    ns2501_writeb(dvo, 0x91, 0x07);
+    ns2501_writeb(dvo, 0x94, 0x00);
+    ns2501_writeb(dvo, 0x95, 0x00);

+
+ ns2501_writeb(dvo, 0x96, 0x00);
+
+ ns2501_writeb(dvo, 0x99, 0x00);
+ ns2501_writeb(dvo, 0x9a, 0x88);
+

+    ns2501_writeb(dvo, 0x9c, 0x23);
+    ns2501_writeb(dvo, 0x9d, 0x00);
+    ns2501_writeb(dvo, 0x9e, 0x25);
+    ns2501_writeb(dvo, 0x9f, 0x03);

+
+ ns2501_writeb(dvo, 0xa4, 0x80);
+
+ ns2501_writeb(dvo, 0xb6, 0x00);
+
+ ns2501_writeb(dvo, 0xb9, 0xc8); /* horizontal? */
+ ns2501_writeb(dvo, 0xba, 0x00); /* horizontal? */
+
+ ns2501_writeb(dvo, 0xc0, 0x05); /* horizontal? */
+ ns2501_writeb(dvo, 0xc1, 0xd7);
+
+ ns2501_writeb(dvo, 0xc2, 0x00);
+ ns2501_writeb(dvo, 0xc3, 0xf8);
+
+ ns2501_writeb(dvo, 0xc4, 0x03);
+ ns2501_writeb(dvo, 0xc5, 0x1a);
+

+    ns2501_writeb(dvo, 0xc6, 0x00);
+    ns2501_writeb(dvo, 0xc7, 0x73);
+    ns2501_writeb(dvo, 0xc8, 0x02);
+
+  } else if (mode->hdisplay == 640 && mode->vdisplay == 480) {
+    /* mode 274 */
+    DRM_DEBUG_KMS("%s: switching to 640x480\n",__FUNCTION__);
+    /*
+    ** No, I do not know where this data comes from.
+    ** It is just what the video bios left in the DVO, so
+    ** I'm just copying it here over.
+    ** This also means that I cannot support any other modes
+    ** except the ones supported by the bios.
+    */
+    ns->reg_8_shadow &= ~NS2501_8_BPAS;
+
+    ns2501_writeb(dvo, 0x11, 0xa0);
+    ns2501_writeb(dvo, 0x1b, 0x11);
+    ns2501_writeb(dvo, 0x1c, 0x54);
+    ns2501_writeb(dvo, 0x1d, 0x03);

+
+ ns2501_writeb(dvo, 0x34, 0x03);
+ ns2501_writeb(dvo, 0x35, 0xff);
+

+    ns2501_writeb(dvo, 0x80, 0xff);
+    ns2501_writeb(dvo, 0x81, 0x07);
+    ns2501_writeb(dvo, 0x82, 0x3d);
+    ns2501_writeb(dvo, 0x83, 0x05);
+
+    ns2501_writeb(dvo, 0x8d, 0x02);
+    ns2501_writeb(dvo, 0x8e, 0x10);
+    ns2501_writeb(dvo, 0x8f, 0x00);
+
+    ns2501_writeb(dvo, 0x90, 0xff); /* vertical */
+    ns2501_writeb(dvo, 0x91, 0x07);
+    ns2501_writeb(dvo, 0x94, 0x00);
+    ns2501_writeb(dvo, 0x95, 0x00);

+
+ ns2501_writeb(dvo, 0x96, 0x05);
+
+ ns2501_writeb(dvo, 0x99, 0x00);
+ ns2501_writeb(dvo, 0x9a, 0x88);
+

+    ns2501_writeb(dvo, 0x9c, 0x24);
+    ns2501_writeb(dvo, 0x9d, 0x00);
+    ns2501_writeb(dvo, 0x9e, 0x25);
+    ns2501_writeb(dvo, 0x9f, 0x03);

+
+ ns2501_writeb(dvo, 0xa4, 0x84);
+
+ ns2501_writeb(dvo, 0xb6, 0x09);
+
+ ns2501_writeb(dvo, 0xb9, 0xa0); /* horizontal? */
+ ns2501_writeb(dvo, 0xba, 0x00); /* horizontal? */
+
+ ns2501_writeb(dvo, 0xc0, 0x05); /* horizontal? */
+ ns2501_writeb(dvo, 0xc1, 0x90);
+
+ ns2501_writeb(dvo, 0xc2, 0x00);
+ ns2501_writeb(dvo, 0xc3, 0x0f);
+
+ ns2501_writeb(dvo, 0xc4, 0x03);
+ ns2501_writeb(dvo, 0xc5, 0x16);
+

+    ns2501_writeb(dvo, 0xc6, 0x00);
+    ns2501_writeb(dvo, 0xc7, 0x02);
+    ns2501_writeb(dvo, 0xc8, 0x02);
+
+  } else if (mode->hdisplay == 1024 && mode->vdisplay == 768) {
+    /* mode 280 */
+    DRM_DEBUG_KMS("%s: switching to 1024x768\n",__FUNCTION__);
+    /*
+    ** This might or might not work, actually. I'm silently
+    ** assuming here that the native panel resolution is
+    ** 1024x768. If not, then this leaves the scaler disabled
+    ** generating a picture that is likely not the expected.
+    **
+    ** Problem is that I do not know where to take the panel
+    ** dimensions from.
+    **
+    ** Enable the bypass, scaling not required.
+    **
+    ** The scaler registers are irrelevant here....
+    **
+    */
+    ns->reg_8_shadow |= NS2501_8_BPAS;
+    ns2501_writeb(dvo, 0x37, 0x44);
+  } else {
+    /* Data not known. Bummer!
+    ** Hopefully, the code should not go here
+    ** as mode_OK delivered no other modes.
+    */
+    ns->reg_8_shadow |= NS2501_8_BPAS;
+  }
+  ns2501_writeb(dvo, NS2501_REG8, ns->reg_8_shadow);
+
+  /*
+  ** Restore the old i915 registers before
+  ** forcing the ns2501 on.
+  */
+  restore_dvo(dvo);

+}
+
+/* set the NS2501 power state */
+static void ns2501_dpms(struct intel_dvo_device *dvo, int mode)
+{
+ struct ns2501_priv *ns = (struct ns2501_priv *)(dvo->dev_priv);
+ unsigned char ch;
+
+ DRM_DEBUG_KMS("%s: Trying set the dpms of the DVO to %d\n",__FUNCTION__,mode); +
+ ch = ns->reg_8_shadow;
+
+ if (mode == DRM_MODE_DPMS_ON)
+ ch |= NS2501_8_PD;
+ else
+ ch &= ~NS2501_8_PD;
+
+ if (ns->reg_8_set == 0 || ns->reg_8_shadow != ch) {

+    ns->reg_8_set    = 1;
+    ns->reg_8_shadow = ch;
+    ns2501_writeb(dvo, NS2501_REG8, ch);
+  }
+  /*
+  ** Note that this may actually fail,namely exactly
+  ** when the chip vanished from the bus.
+  **
+  ** Should I force-enable it here??
+  */

+}
+
+static void ns2501_dump_regs(struct intel_dvo_device *dvo) +{
+ uint8_t val;
+

+  ns2501_readb(dvo, NS2501_FREQ_LO, &val);
+  DRM_LOG_KMS("NS2501_FREQ_LO: 0x%02x\n", val);
+  ns2501_readb(dvo, NS2501_FREQ_HI, &val);
+  DRM_LOG_KMS("NS2501_FREQ_HI: 0x%02x\n", val);
+  ns2501_readb(dvo, NS2501_REG8, &val);
+  DRM_LOG_KMS("NS2501_REG8: 0x%02x\n", val);
+  ns2501_readb(dvo, NS2501_REG9, &val);
+  DRM_LOG_KMS("NS2501_REG9: 0x%02x\n", val);
+  ns2501_readb(dvo, NS2501_REGC, &val);
+  DRM_LOG_KMS("NS2501_REGC: 0x%02x\n", val);

+}
+
+static void ns2501_destroy(struct intel_dvo_device *dvo) +{
+ struct ns2501_priv *ns = dvo->dev_priv;
+
+ if (ns) {
+ kfree(ns);
+ dvo->dev_priv = NULL;
+ }
+}
+
+struct intel_dvo_dev_ops ns2501_ops = {

+  .init = ns2501_init,
+  .detect = ns2501_detect,
+  .mode_valid = ns2501_mode_valid,
+  .mode_set = ns2501_mode_set,
+  .dpms = ns2501_dpms,
+  .dump_regs = ns2501_dump_regs,
+  .destroy = ns2501_destroy,

+};

drivers/gpu/drm/i915/intel_display.c 2012-06-08 16:55:20.000000000 +0200 renamed from drivers/gpu/drm/i915/intel_display.c 2012-06-01 09:18:44.000000000 +0200 +1 -1
diff -rup linux-3.4.1-orig/drivers/gpu/drm/i915/intel_display.c linux-3.4.1/drivers/gpu/drm/i915/intel_display.c
@@ -1142,7 +1142,7 @@ static void assert_pch_ports_disabled(st
  *
  * Note!  This is for pre-ILK only.
  */
-static void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)
+void intel_enable_pll(struct drm_i915_private *dev_priv, enum pipe pipe)
 {
     int reg;
     u32 val;
drivers/gpu/drm/i915/intel_dvo.c 2012-06-08 12:50:16.000000000 +0200 renamed from drivers/gpu/drm/i915/intel_dvo.c 2012-06-01 09:18:44.000000000 +0200 +8 -0
diff -rup linux-3.4.1-orig/drivers/gpu/drm/i915/intel_dvo.c linux-3.4.1/drivers/gpu/drm/i915/intel_dvo.c
@@ -37,6 +37,7 @@
 #define SIL164_ADDR    0x38
 #define CH7xxx_ADDR    0x76
 #define TFP410_ADDR    0x38
+#define NS2501_ADDR     0x38
 
 static const struct intel_dvo_device intel_dvo_devices[] = {
     {
@@ -61,6 +62,13 @@ static const struct intel_dvo_device int
         .dev_ops = &ivch_ops,
     },
     {
+            .type = INTEL_DVO_CHIP_TMDS,
+            .name = "ns2501",
+            .dvo_reg = DVOC,
+            .slave_addr = NS2501_ADDR,
+            .dev_ops = &ns2501_ops,
+    },
+    {
         .type = INTEL_DVO_CHIP_TMDS,
         .name = "tfp410",
         .dvo_reg = DVOC,
drivers/gpu/drm/i915/Makefile 2012-06-08 12:50:54.000000000 +0200 renamed from drivers/gpu/drm/i915/Makefile 2012-06-01 09:18:44.000000000 +0200 +2 -1
diff -rup linux-3.4.1-orig/drivers/gpu/drm/i915/Makefile linux-3.4.1/drivers/gpu/drm/i915/Makefile
@@ -34,7 +34,8 @@ i915-y := i915_drv.o i915_dma.o i915_irq
       dvo_ch7017.o \
       dvo_ivch.o \
       dvo_tfp410.o \
-      dvo_sil164.o
+      dvo_sil164.o \
+      dvo_ns2501.o
 
 i915-$(CONFIG_COMPAT)   += i915_ioc32.o
 

/* snip */

Please check and confirm to which degree this is working.

Thanks,
Thomas