Skip to contentSkip to conversation

How to start barebox on Freescale iMX28 EVK

DISCUSSION Maxime Ripard 2 participants 4 messages Jun 18, 2012 – Jun 29, 2012

lore
Share & tools
lore
#0 lore raw

Hi everyone,

I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.

I think I might have a problem with the bootlets used, but I'm not sure.

So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- make imx28evk_defconfig ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- make

Using codebench 2011.09 toolchain.

Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].

After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sb

Finally, I pushed on a properly formatted SD Card (with a 0x53 partition flag on the first partition) using Freescale mk_hdr script[2] to generate the proper headers:

./mk_hdr.sh sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}' 1 > temp.bin

sudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=sync

When I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address: 0x8050100f

When flashing it in the exact same way with freescale's precompiled u-boot bootstream, it works fine though, so my guess is that it is more a problem regarding the barebox binary/the bootstream than the sd card generation process...

Do you have an idea on what could be wrong with what I'm doing ?

Thanks,
Maxime

[1] http://code.bulix.org/eavngs-81672
[2] http://code.bulix.org/vzqsiy-81673

Signature · 9 lines
Maxime Ripard, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#1 lore raw

Anyone ?

Quoted 47 lines · Maxime Ripard

Hi everyone,

I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.

I think I might have a problem with the bootlets used, but I'm not sure.

So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- make imx28evk_defconfig ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- make

Using codebench 2011.09 toolchain.

Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].

After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sb

Finally, I pushed on a properly formatted SD Card (with a 0x53 partition flag on the first partition) using Freescale mk_hdr script[2] to generate the proper headers:

./mk_hdr.sh sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}' 1 > temp.bin

sudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=sync

When I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address: 0x8050100f

When flashing it in the exact same way with freescale's precompiled u-boot bootstream, it works fine though, so my guess is that it is more a problem regarding the barebox binary/the bootstream than the sd card generation process...

Do you have an idea on what could be wrong with what I'm doing ?

Thanks,
Maxime

[1] http://code.bulix.org/eavngs-81672
[2] http://code.bulix.org/vzqsiy-81673

Signature · 11 lines
Maxime Ripard, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com



_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#2 lore raw
Quoted 36 lines · Maxime Ripard

Anyone ?

Quoted 33 lines · Maxime Ripard

Hi everyone,

I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.

I think I might have a problem with the bootlets used, but I'm not sure.

So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- make imx28evk_defconfig ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- make

Using codebench 2011.09 toolchain.

Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].

After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sb

Finally, I pushed on a properly formatted SD Card (with a 0x53 partition flag on the first partition) using Freescale mk_hdr script[2] to generate the proper headers:

./mk_hdr.sh sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}' 1 > temp.bin

sudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=sync

When I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address: 0x8050100f

This code comes from the i.MX28 ROM and means:

Requested data beyond the end of a section.

Maybe your entry point is wrong? I just had a look at our .bd file and it looks like this:

sources {
        power_prep="./power_prep/power_prep";
        u_boot="/home/sha/dude/bosch/OSELAS.BSP-Bosch-SCM/platform-scm/build-target/barebox-2012.05.0/barebox";
}

section (0) {

        //----------------------------------------------------------
        // Power Supply initialization
        //----------------------------------------------------------

        load power_prep;
        load ivt (entry = power_prep:_start) > 0x8000;
        hab call 0x8000;

        //----------------------------------------------------------
        //  Load and call u_boot - ELF ARM image
        //----------------------------------------------------------

        load u_boot;
        load ivt (entry = u_boot:exception_vectors) > 0x8000;
        hab call 0x8000;

}

Signature · 9 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#3 lore raw

Hi,

Quoted 68 lines · Sascha Hauer
Quoted 36 lines · Maxime Ripard

Anyone ?

Quoted 33 lines · Maxime Ripard

Hi everyone,

I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.

I think I might have a problem with the bootlets used, but I'm not sure.

So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- make imx28evk_defconfig ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- make

Using codebench 2011.09 toolchain.

Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].

After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sb

Finally, I pushed on a properly formatted SD Card (with a 0x53 partition flag on the first partition) using Freescale mk_hdr script[2] to generate the proper headers:

./mk_hdr.sh sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}' 1 > temp.bin

sudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=sync

When I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address: 0x8050100f

This code comes from the i.MX28 ROM and means:

Requested data beyond the end of a section.

Maybe your entry point is wrong? I just had a look at our .bd file and it looks like this:

sources {
        power_prep="./power_prep/power_prep";
        u_boot="/home/sha/dude/bosch/OSELAS.BSP-Bosch-SCM/platform-scm/build-target/barebox-2012.05.0/barebox";
}

section (0) {

        //----------------------------------------------------------
        // Power Supply initialization
        //----------------------------------------------------------

        load power_prep;
        load ivt (entry = power_prep:_start) > 0x8000;
        hab call 0x8000;

        //----------------------------------------------------------
        //  Load and call u_boot - ELF ARM image
        //----------------------------------------------------------

        load u_boot;
        load ivt (entry = u_boot:exception_vectors) > 0x8000;
        hab call 0x8000;
Quoted 1 line

}

Yep, it was just that. Changing the entry point to exception_vectors did the trick. Thanks a lot!

Maxime

Signature · 11 lines
Maxime Ripard, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com



_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox