How to start barebox on Freescale iMX28 EVK
Hi everyone,
I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.
I think I might have a problem with the bootlets used, but I'm not sure.
So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- make imx28evk_defconfig ARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- make
Using codebench 2011.09 toolchain.
Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].
After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sb
Finally, I pushed on a properly formatted SD Card (with a 0x53 partition flag on the first partition) using Freescale mk_hdr script[2] to generate the proper headers:
./mk_hdr.sh sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}' 1 > temp.bin
sudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=sync
When I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address: 0x8050100f
When flashing it in the exact same way with freescale's precompiled u-boot bootstream, it works fine though, so my guess is that it is more a problem regarding the barebox binary/the bootstream than the sd card generation process...
Do you have an idea on what could be wrong with what I'm doing ?
Thanks,
Maxime
[1] http://code.bulix.org/eavngs-81672
[2] http://code.bulix.org/vzqsiy-81673
Signature · 9 lines
Maxime Ripard, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Anyone ?
Quoted 47 lines · Maxime Ripard
Hi everyone,
I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.
I think I might have a problem with the bootlets used, but I'm not sure.
So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- makeimx28evk_defconfigARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- makeUsing codebench 2011.09 toolchain.
Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].
After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sbFinally, I pushed on a properly formatted SD Card (with a
0x53partition flag on the first partition) using Freescalemk_hdrscript[2] to generate the proper headers:./mk_hdr.sh
sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}'1 > temp.binsudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=syncWhen I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address:
0x8050100fWhen flashing it in the exact same way with freescale's precompiled u-boot bootstream, it works fine though, so my guess is that it is more a problem regarding the barebox binary/the bootstream than the sd card generation process...
Do you have an idea on what could be wrong with what I'm doing ?
Thanks,
Maxime[1] http://code.bulix.org/eavngs-81672
[2] http://code.bulix.org/vzqsiy-81673
Signature · 11 lines
Maxime Ripard, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 36 lines · Maxime Ripard
Anyone ?
Quoted 33 lines · Maxime Ripard
Hi everyone,
I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.
I think I might have a problem with the bootlets used, but I'm not sure.
So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- makeimx28evk_defconfigARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- makeUsing codebench 2011.09 toolchain.
Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].
After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sbFinally, I pushed on a properly formatted SD Card (with a
0x53partition flag on the first partition) using Freescalemk_hdrscript[2] to generate the proper headers:./mk_hdr.sh
sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}'1 > temp.binsudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=syncWhen I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address:
0x8050100f
This code comes from the i.MX28 ROM and means:
Requested data beyond the end of a section.
Maybe your entry point is wrong? I just had a look at our .bd file and it looks like this:
sources {
power_prep="./power_prep/power_prep";
u_boot="/home/sha/dude/bosch/OSELAS.BSP-Bosch-SCM/platform-scm/build-target/barebox-2012.05.0/barebox";
}section (0) {
//----------------------------------------------------------
// Power Supply initialization
//----------------------------------------------------------
load power_prep;
load ivt (entry = power_prep:_start) > 0x8000;
hab call 0x8000;
//----------------------------------------------------------
// Load and call u_boot - ELF ARM image
//----------------------------------------------------------
load u_boot;
load ivt (entry = u_boot:exception_vectors) > 0x8000;
hab call 0x8000;}
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Hi,
Quoted 68 lines · Sascha Hauer
Quoted 36 lines · Maxime Ripard
Anyone ?
Quoted 33 lines · Maxime Ripard
Hi everyone,
I'm trying barebox on the imx28 evk evaluation board from freescale, and I can't get barebox to boot yet.
I think I might have a problem with the bootlets used, but I'm not sure.
So, to compile barebox, I did:
ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- makeimx28evk_defconfigARCH=arm CROSS_COMPILE=arm-none-linux-gnueabi- makeUsing codebench 2011.09 toolchain.
Then, I used U-boot IVT bootlet from freescale bootlet tarball as a base for the one I created [1].
After that, I created the bootstream using
elftosb -z -f imx28 -c ./barebox_ivt.bd -o imx28_ivt_barebox.sbFinally, I pushed on a properly formatted SD Card (with a
0x53partition flag on the first partition) using Freescalemk_hdrscript[2] to generate the proper headers:./mk_hdr.sh
sudo fdisk -lu /dev/sdb | awk '$5==53 {print $2}'1 > temp.binsudo dd if=temp.bin of=/dev/sdb1 ibs=512 conv=sync
sudo dd if=imx28_ivt_barebox.sb of=/dev/sdb1 ibs=512 obs=512 seek=1 conv=syncWhen I finally plug the card in and boot the card, the two first bootlets are properly executed, and then, it hangs, displaying nothing but what is looking like an address:
0x8050100fThis code comes from the i.MX28 ROM and means:
Requested data beyond the end of a section.
Maybe your entry point is wrong? I just had a look at our .bd file and it looks like this:
sources { power_prep="./power_prep/power_prep"; u_boot="/home/sha/dude/bosch/OSELAS.BSP-Bosch-SCM/platform-scm/build-target/barebox-2012.05.0/barebox"; }section (0) {
//---------------------------------------------------------- // Power Supply initialization //---------------------------------------------------------- load power_prep; load ivt (entry = power_prep:_start) > 0x8000; hab call 0x8000; //---------------------------------------------------------- // Load and call u_boot - ELF ARM image //---------------------------------------------------------- load u_boot; load ivt (entry = u_boot:exception_vectors) > 0x8000; hab call 0x8000;
Quoted 1 line
}
Yep, it was just that. Changing the entry point to exception_vectors did the trick. Thanks a lot!
Maxime
Signature · 11 lines
Maxime Ripard, Free Electrons Kernel, drivers, real-time and embedded Linux development, consulting, training and support. http://free-electrons.com _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox