Skip to contentSkip to conversation

Pandaboard Kernel 3.8.13.6 no HDMI

DISCUSSION Sid Boyce 2 participants 2 messages Sep 3, 2013

lore
Share & tools
lore

Sid Boyce

author
#0 lore raw

The Pandaboard list seems dormant so I am seeking help here.

The previous kernel with HDMI video output was 3.2.7x5.

I built and installed this new kernel with this xorg.conf, it does not work. Section "Device"

        Identifier      "fb0"
        Driver "omapfb"
        Option "fb" "/dev/fb0"

EndSection

Section "Monitor"

        Identifier "HP"
        ModeLine "1920x1080" 148.501  1920 2008 2052 2200  1080 1084 1089

1125 -HSync -VSync
EndSection

Section "Screen"

        Identifier      "screen0"
        Device  "fb0"
        Monitor "HP"
        DefaultDepth    16
        SubSection "Display"
                Depth   16
                Modes   "1920x1080" "800x480"
        EndSubSection

EndSection

Mode "800x480"

    # D: 29.001 MHz, H: 31.251 kHz, V: 59.525 Hz
    DotClock 29.002
    HTimings 800 840 888 928
    VTimings 480 503 506 525
    Flags    "-HSync" "-VSync"

EndMode

Using the udlfb driver and an xorg.conf for the Lilliput USB 7" screen there is no problem, LXDE is up and running and CRTL-ALT-F1 etc. all OK, but I need the USB screen for the Beaglebone.

root@panda:/etc/X11# lsmod
Module                  Size  Used by
omapdss               253516  0
udlfb                  17703  2
bluetooth             221172  6
snd_usb_audio         115881  0
snd_usbmidi_lib        18680  1 snd_usb_audio
snd_rawmidi            21747  1 snd_usbmidi_lib
snd_hwdep               6190  1 snd_usb_audio
snd_pcm_oss            42617  0
snd_mixer_oss          14244  1 snd_pcm_oss
snd_pcm                84961  2 snd_pcm_oss,snd_usb_audio
snd_page_alloc          5296  1 snd_pcm
snd_timer              20277  1 snd_pcm
snd                    61483  8 snd_pcm_oss,snd_usb_audio,snd_hwdep,snd_timer,snd_pcm,snd_rawmidi,snd_usbmidi_lib,snd_mixer_oss
soundcore               7260  1 snd
ehci_hcd               54613  0
ohci_hcd               31836  0
root@panda:/etc/X11# ls /lib/modules/3.8.13.6x-dirty/kernel/drivers/video/
backlight  omap2  udlfb.ko
root@panda:/etc/X11# ll /lib/modules/3.8.13.6x-dirty/kernel/drivers/video/omap2/omapfb
total 64
drwxr-xr-x 2 root root  4096 Sep  2 10:18 ./
drwxr-xr-x 5 root root  4096 Sep  2 10:18 ../
-rw-r--r-- 1 root root 56916 Sep  2 02:52 omapfb.ko
root@panda:/etc/X11# modprobe omapfb
ERROR: could not insert 'omapfb': No such device
root@panda:/etc/X11# insmod /lib/modules/3.8.13.6x-dirty/kernel/drivers/video/omap2/omapfb/omapfb.ko
Error: could not insert module /lib/modules/3.8.13.6x-dirty/kernel/drivers/video/omap2/omapfb/omapfb.ko: No such device
root@panda:/1/ubuntu-raring# grep CONFIG_FB .config
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SYS_FILLRECT=y
CONFIG_FB_SYS_COPYAREA=y
CONFIG_FB_SYS_IMAGEBLIT=y
CONFIG_FB_SYS_FOPS=y
CONFIG_FB_DEFERRED_IO=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_ARMCLCD=y
CONFIG_FB_UVESA=y
CONFIG_FB_TMIO=y
CONFIG_FB_TMIO_ACCELL=y
CONFIG_FB_UDL=m
CONFIG_FB_VIRTUAL=y
CONFIG_OMAP2_VRFB=y
CONFIG_OMAP2_DSS_RFBI=y
CONFIG_FB_OMAP2=m
CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
CONFIG_FB_OMAP2_NUM_FBS=3
root@panda:/etc/X11# grep HDMI /1/ubuntu-raring/.config
CONFIG_OMAP4_DSS_HDMI=y

ONFIG_ARCH_OMAP4=y
CONFIG_MACH_OMAP4_PANDA=y

Displayed on the serial console
=======================

root@panda:~# [34587.439270] omapdss error: timeout reading edid
[34587.445220] omapfb omapfb: failed to allocate framebuffer
[34587.450958] omapfb omapfb: failed to allocate fbmem
[34587.456604] omapfb omapfb: failed to setup omapfb
[34587.461853] failed to register omapfb driver
Regards
Sid.
Signature · 4 lines
Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot
Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support
Senior Staff Specialist, Cricket Coach
Microsoft Windows Free Zone - Linux used for all Computing Tasks
#1 lore raw

Hi,

There are a couple of options here.

Quoted 11 lines · Sid Boyce

The Pandaboard list seems dormant so I am seeking help here.

The previous kernel with HDMI video output was 3.2.7x5.

I built and installed this new kernel with this xorg.conf, it does not work.
Section "Device"

         Identifier      "fb0"
         Driver "omapfb"
         Option "fb" "/dev/fb0"

EndSection

Looks like the problem below was buffer allocation. You could use omapdrm instead of omapfb which should allocate buffers successfully. I think the omapdrm drivers was in staging at that point. You could search for it in the .config, and set NUM_CRTCS to 2.

Quoted 80 lines

Section "Monitor"

         Identifier "HP"
         ModeLine "1920x1080" 148.501  1920 2008 2052 2200  1080 1084 1089

1125 -HSync -VSync
EndSection

Section "Screen"

         Identifier      "screen0"
         Device  "fb0"
         Monitor "HP"
         DefaultDepth    16
         SubSection "Display"
                 Depth   16
                 Modes   "1920x1080" "800x480"
         EndSubSection

EndSection

Mode "800x480"

     # D: 29.001 MHz, H: 31.251 kHz, V: 59.525 Hz
     DotClock 29.002
     HTimings 800 840 888 928
     VTimings 480 503 506 525
     Flags    "-HSync" "-VSync"

EndMode

Using the udlfb driver and an xorg.conf for the Lilliput USB 7" screen there is no problem, LXDE is up and running and CRTL-ALT-F1 etc. all OK, but I need the USB screen for the Beaglebone.

root@panda:/etc/X11# lsmod
Module                  Size  Used by
omapdss               253516  0
udlfb                  17703  2
bluetooth             221172  6
snd_usb_audio         115881  0
snd_usbmidi_lib        18680  1 snd_usb_audio
snd_rawmidi            21747  1 snd_usbmidi_lib
snd_hwdep               6190  1 snd_usb_audio
snd_pcm_oss            42617  0
snd_mixer_oss          14244  1 snd_pcm_oss
snd_pcm                84961  2 snd_pcm_oss,snd_usb_audio
snd_page_alloc          5296  1 snd_pcm
snd_timer              20277  1 snd_pcm
snd                    61483  8
snd_pcm_oss,snd_usb_audio,snd_hwdep,snd_timer,snd_pcm,snd_rawmidi,snd_usbmidi_lib,snd_mixer_oss
soundcore               7260  1 snd
ehci_hcd               54613  0
ohci_hcd               31836  0
root@panda:/etc/X11# ls /lib/modules/3.8.13.6x-dirty/kernel/drivers/video/
backlight  omap2  udlfb.ko
root@panda:/etc/X11# ll
/lib/modules/3.8.13.6x-dirty/kernel/drivers/video/omap2/omapfb
total 64
drwxr-xr-x 2 root root  4096 Sep  2 10:18 ./
drwxr-xr-x 5 root root  4096 Sep  2 10:18 ../
-rw-r--r-- 1 root root 56916 Sep  2 02:52 omapfb.ko
root@panda:/etc/X11# modprobe omapfb
ERROR: could not insert 'omapfb': No such device
root@panda:/etc/X11# insmod
/lib/modules/3.8.13.6x-dirty/kernel/drivers/video/omap2/omapfb/omapfb.ko
Error: could not insert module
/lib/modules/3.8.13.6x-dirty/kernel/drivers/video/omap2/omapfb/omapfb.ko: No
such device
root@panda:/1/ubuntu-raring# grep CONFIG_FB .config
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
CONFIG_FB_SYS_FILLRECT=y
CONFIG_FB_SYS_COPYAREA=y
CONFIG_FB_SYS_IMAGEBLIT=y
CONFIG_FB_SYS_FOPS=y
CONFIG_FB_DEFERRED_IO=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_TILEBLITTING=y
CONFIG_FB_ARMCLCD=y
CONFIG_FB_UVESA=y
CONFIG_FB_TMIO=y
Quoted 8 lines
CONFIG_FB_TMIO_ACCELL=y
CONFIG_FB_UDL=m
CONFIG_FB_VIRTUAL=y
CONFIG_OMAP2_VRFB=y
CONFIG_OMAP2_DSS_RFBI=y
CONFIG_FB_OMAP2=m
CONFIG_FB_OMAP2_DEBUG_SUPPORT=y
CONFIG_FB_OMAP2_NUM_FBS=3

The other option is to figure out why it's not working with omapfb. Could you add a CONFIG_OMAP2_DSS_DEBUG in order to get additional DSS prints?

Quoted 7 lines
root@panda:/etc/X11# grep HDMI /1/ubuntu-raring/.config
CONFIG_OMAP4_DSS_HDMI=y

ONFIG_ARCH_OMAP4=y
CONFIG_MACH_OMAP4_PANDA=y

Quoted 7 lines

Displayed on the serial console
=======================

root@panda:~# [34587.439270] omapdss error: timeout reading edid
[34587.445220] omapfb omapfb: failed to allocate framebuffer
[34587.450958] omapfb omapfb: failed to allocate fbmem
[34587.456604] omapfb omapfb: failed to setup omapfb
[34587.461853] failed to register omapfb driver

The debug prints will help with the edid timeout. About the allocation of buffers, I think it should work if you enable CMA. And set CONFIG_CMA_SIZE_MBYTES to say, 24 Mb. That should allocate the buffers successfully.

Archit