ARM: dts: am335x-bone-common: correct mux mode for cmd line
PATCH 1/2 ARM: dts: am335x-bone-common: correct mux mode for cmd line
pinmux_emmc_pins: mux mode for cmd line should be MODE2
to detect eMMC on beagle bone black and beagle bone white + eMMC cape.
---
based on git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git for_3.13/dts
arch/arm/boot/dts/am335x-bone-common.dtsi | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
arch/arm/boot/dts/am335x-bone-common.dtsi +1 -1
@@ -153,7 +153,7 @@ emmc_pins: pinmux_emmc_pins { pinctrl-single,pins = < 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_csn2.mmc1_cmd */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
Signature · 1 line
1.7.5.4
PATCH 2/2 ARM: dts: am335x-evm, am335x-evmsdk: switch mmc1 to 4-bit mode
set bus-width to make SD card operate in 4 bit mode.
---
based on git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.git for_3.13/dts
arch/arm/boot/dts/am335x-evm.dts | 1 + arch/arm/boot/dts/am335x-evmsk.dts | 1 + 2 files changed, 2 insertions(+), 0 deletions(-)
arch/arm/boot/dts/am335x-evm.dts +1 -0
@@ -521,4 +521,5 @@ &mmc1 { status = "okay"; vmmc-supply = <&vmmc_reg>; + bus-width = <4>; };
arch/arm/boot/dts/am335x-evmsk.dts +1 -0
@@ -423,4 +423,5 @@ &mmc1 { status = "okay"; vmmc-supply = <&vmmc_reg>; + bus-width = <4>; };
Signature · 1 line
1.7.5.4
PATCH 2/2 ARM: dts: am335x-evm, am335x-evmsdk: switch mmc1 to 4-bit mode
Hi Balaji,
Quoted 26 lines · Balaji T K
set bus-width to make SD card operate in 4 bit mode.
Signed-off-by Balaji T K <[email protected]>---
based ongit://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.gitfor_3.13/dtsarch/arm/boot/dts/am335x-evm.dts | 1 + arch/arm/boot/dts/am335x-evmsk.dts | 1 + 2 files changed, 2 insertions(+), 0 deletions(-)arch/arm/boot/dts/am335x-evm.dts +1
-0@@ -521,4 +521,5 @@ &mmc1 { status = "okay"; vmmc-supply = <&vmmc_reg>; + bus-width = <4>; };arch/arm/boot/dts/am335x-evmsk.dts +0
-0
arch/arm/boot/dts/am335x-evmsk.dts line 427
Quoted 5 lines
arch/arm/boot/dts/am335x-evmsk.dts +1
-0@@ -423,4 +423,5 @@ &mmc1 { status = "okay"; vmmc-supply = <&vmmc_reg>; + bus-width = <4>; };
Thanks, I'll apply it for 3.13.
Regards,
Benoit
PATCH 1/2 ARM: dts: am335x-bone-common: correct mux mode for cmd line
In reply to Balaji T KHi Balaji,
Quoted 17 lines · Balaji T K
pinmux_emmc_pins: mux mode for cmd line should be MODE2
to detect eMMC on beagle bone black and beagle bone white + eMMC cape.Signed-off-by Balaji T K <[email protected]>Tested-by Felipe Balbi <[email protected]>---
based ongit://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt.gitfor_3.13/dtsarch/arm/boot/dts/am335x-bone-common.dtsi | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)arch/arm/boot/dts/am335x-bone-common.dtsi +0
-0
arch/arm/boot/dts/am335x-bone-common.dtsi line 159
Quoted 8 lines
arch/arm/boot/dts/am335x-bone-common.dtsi +1
-1@@ -153,7 +153,7 @@ emmc_pins: pinmux_emmc_pins { pinctrl-single,pins = < 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ - 0x84 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_csn2.mmc1_cmd */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
Thanks, I'll apply it for 3.13.
Regards,
Benoit