Skip to contentSkip to conversation

problems porting to 2013.x

U-Boot Chris Ruehl 2 participants 5 messages Oct 9, 2013 – Oct 10, 2013

lore
Share & tools
lore
#0 lore raw

Hi.

I hope someone can open my eyes on this. We try to port our MX27 board to the new u-boot loader using the SPL code rather then the self hacked NAND->SDRAM.

I'm not able to get anything run. The console stays dead.

Let start here:
To see if the second image is booting I tried to load the image using TFTP and memcpy/memcmp it to the TEXT_BASE (0xa7800000) and go. The u-boot-v2 is loaded at 0xa7f00000.

U-Boot 2.0.0-rc9-00188-geb5172d-dirty (Mar 24 2011 - 12:59:07)
Board: MX27
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks
Bad eraseblock 592 at 0x04a00000
dm9000 i/o: 0xd4000000, id: 0x90000a46
got MAC address from EEPROM: 00:00:00:00:00:00
Using environment in NAND Flash

chip id: [2,882,1,01d]
mpll:     398999390 Hz
spll:     239999725 Hz
arm:      265999593 Hz
perclk1:   66499898 Hz
perclk2:   66499898 Hz
perclk3:   66499898 Hz
perclk4:   66499898 Hz
clkin26:   26000000 Hz
ahb:      132999796 Hz
ipg:       66499898 Hz
Malloc space: 0xa6f00000 -> 0xa7f00000 (size 16 MB)
Stack space : 0xa6ef8000 -> 0xa6f00000 (size 32 kB)

running /env/bin/init...

uboot:/ tftp u-boot.bin /dev/ram0
phy0: Link is up - 100/Full
TFTP from server 10.128.2.105; our IP address is 10.128.2.10 Filename 'u-boot.bin'.
Loading: ########################################## done
Bytes transferred = 211308 (3396c hex)
uboot:/ memcpy -s /dev/ram0 0 0xa7800000 211308 uboot:/ memcmp -s /dev/ram0 0 0xa7800000 211308
OK
uboot:/ go 0xa7800000
## Starting application at 0xA7800000 ...

System.map
a7800000 T __image_copy_start
a7800000 T _start
a7800020 t _undefined_instruction
a7800024 t _software_interrupt
a7800028 t _prefetch_abort
a780002c t _data_abort
a7800030 t _not_used
a7800034 t _irq
a7800038 t _fiq
...

Any Idea?

Chris

#1 lore raw
Quoted 63 lines · Chris Ruehl

Hi.

I hope someone can open my eyes on this. We try to port our MX27 board to the new u-boot loader using the SPL code rather then the self hacked NAND->SDRAM.

I'm not able to get anything run. The console stays dead.

Let start here:
To see if the second image is booting I tried to load the image using TFTP and memcpy/memcmp it to the TEXT_BASE (0xa7800000) and go. The u-boot-v2 is loaded at 0xa7f00000.

U-Boot 2.0.0-rc9-00188-geb5172d-dirty (Mar 24 2011 - 12:59:07)
Board: MX27
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 592 at 0x04a00000
dm9000 i/o: 0xd4000000, id: 0x90000a46
got MAC address from EEPROM: 00:00:00:00:00:00
Using environment in NAND Flash
chip id: [2,882,1,01d]
mpll: 398999390 Hz
spll: 239999725 Hz
arm: 265999593 Hz
perclk1: 66499898 Hz
perclk2: 66499898 Hz
perclk3: 66499898 Hz
perclk4: 66499898 Hz
clkin26: 26000000 Hz
ahb: 132999796 Hz
ipg: 66499898 Hz
Malloc space: 0xa6f00000 -> 0xa7f00000 (size 16 MB)
Stack space : 0xa6ef8000 -> 0xa6f00000 (size 32 kB)
running /env/bin/init...

uboot:/ tftp u-boot.bin /dev/ram0
phy0: Link is up - 100/Full
TFTP from server 10.128.2.105; our IP address is 10.128.2.10 Filename 'u-boot.bin'.
Loading: ########################################## done
Bytes transferred = 211308 (3396c hex)
uboot:/ memcpy -s /dev/ram0 0 0xa7800000 211308 uboot:/ memcmp -s /dev/ram0 0 0xa7800000 211308
OK
uboot:/ go 0xa7800000
## Starting application at 0xA7800000 ...

System.map
a7800000 T __image_copy_start
a7800000 T _start
a7800020 t _undefined_instruction
a7800024 t _software_interrupt
a7800028 t _prefetch_abort
a780002c t _data_abort
a7800030 t _not_used
a7800034 t _irq
a7800038 t _fiq
...

Quoted 4 lines

Any Idea?

Chris

More info:
I'd compiled the hello_world
make[1]: Entering directory
`/opt/cross_build/uboot.d/u-boot-git/examples/standalone'
arm-linux-gnueabihf-gcc -g -Os -ffunction-sections -fdata-sections
-fno-common -ffixed-r8 -msoft-float -D__KERNEL__
-DCONFIG_SYS_TEXT_BASE=0xa7800000 -DCONFIG_SPL_TEXT_BASE=0xa7400000
-DCONFIG_SPL_PAD_TO=5632 -I/opt/cross_build/uboot.d/u-boot-git/include
-fno-builtin -ffreestanding -nostdinc -isystem /opt/armhf/gcc-linaro-arm-linux-gnueabihf-4.8-2013.07-1_linux/bin/../lib/gcc/arm-linux-gnueabihf/4.8.2/include -pipe -DCONFIG_ARM -D__ARM__ -marm -mno-thumb-interwork -mabi=aapcs-linux
-march=armv5te -Wall -Wstrict-prototypes -fno-stack-protector
-Wno-format-nonliteral -Wno-format-security -fstack-usage -fno-toplevel-reorder
-o hello_world.o hello_world.c -c
arm-linux-gnueabihf-gcc -g -Os -ffunction-sections -fdata-sections
-fno-common -ffixed-r8 -msoft-float -D__KERNEL__
-DCONFIG_SYS_TEXT_BASE=0xa7800000 -DCONFIG_SPL_TEXT_BASE=0xa7400000
-DCONFIG_SPL_PAD_TO=5632 -I/opt/cross_build/uboot.d/u-boot-git/include
-fno-builtin -ffreestanding -nostdinc -isystem /opt/armhf/gcc-linaro-arm-linux-gnueabihf-4.8-2013.07-1_linux/bin/../lib/gcc/arm-linux-gnueabihf/4.8.2/include -pipe -DCONFIG_ARM -D__ARM__ -marm -mno-thumb-interwork -mabi=aapcs-linux
-march=armv5te -Wall -Wstrict-prototypes -fno-stack-protector
-Wno-format-nonliteral -Wno-format-security -fstack-usage -fno-toplevel-reorder
-o stubs.o stubs.c -c
arm-linux-gnueabihf-ld.bfd -r -o libstubs.o stubs.o

arm-linux-gnueabihf-ld.bfd  -g -Ttext 0xa0000000 \
			-o hello_world -e hello_world hello_world.o libstubs.o \

-L/opt/armhf/gcc-linaro-arm-linux-gnueabihf-4.8-2013.07-1_linux/bin/../lib/gcc/arm-linux-gnueabihf/4.8.2 -lgcc
arm-linux-gnueabihf-objcopy -O srec hello_world hello_world.srec 2>/dev/null arm-linux-gnueabihf-objcopy -O binary hello_world hello_world.bin 2>/dev/null

same, its not working

uboot:/ tftp hello_world.bin
phy0: Link is up - 100/Full
TFTP from server 10.128.2.105; our IP address is 10.128.2.10 Filename 'hello_world.bin'.
Loading: #
done
Bytes transferred = 590 (24e hex)
uboot:/ go hello_world.bin
memmap: Invalid argument
uboot:/ cp hello_world.bin /dev/ram0
uboot:/ go /dev/ram0
## Starting application at 0xA0000000 ...

Thanks for any hint.
Chris

#2 lore raw
Quoted 120 lines · Chris Ruehl
Quoted 63 lines · Chris Ruehl

Hi.

I hope someone can open my eyes on this. We try to port our MX27 board to the new u-boot loader using the SPL code rather then the self hacked NAND->SDRAM.

I'm not able to get anything run. The console stays dead.

Let start here:
To see if the second image is booting I tried to load the image using TFTP and memcpy/memcmp it to the TEXT_BASE (0xa7800000) and go. The u-boot-v2 is loaded at 0xa7f00000.

U-Boot 2.0.0-rc9-00188-geb5172d-dirty (Mar 24 2011 - 12:59:07)
Board: MX27
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 592 at 0x04a00000
dm9000 i/o: 0xd4000000, id: 0x90000a46
got MAC address from EEPROM: 00:00:00:00:00:00
Using environment in NAND Flash
chip id: [2,882,1,01d]
mpll: 398999390 Hz
spll: 239999725 Hz
arm: 265999593 Hz
perclk1: 66499898 Hz
perclk2: 66499898 Hz
perclk3: 66499898 Hz
perclk4: 66499898 Hz
clkin26: 26000000 Hz
ahb: 132999796 Hz
ipg: 66499898 Hz
Malloc space: 0xa6f00000 -> 0xa7f00000 (size 16 MB)
Stack space : 0xa6ef8000 -> 0xa6f00000 (size 32 kB)
running /env/bin/init...

uboot:/ tftp u-boot.bin /dev/ram0
phy0: Link is up - 100/Full
TFTP from server 10.128.2.105; our IP address is 10.128.2.10 Filename 'u-boot.bin'.
Loading: ########################################## done
Bytes transferred = 211308 (3396c hex)
uboot:/ memcpy -s /dev/ram0 0 0xa7800000 211308 uboot:/ memcmp -s /dev/ram0 0 0xa7800000 211308
OK
uboot:/ go 0xa7800000
## Starting application at 0xA7800000 ...

System.map
a7800000 T __image_copy_start
a7800000 T _start
a7800020 t _undefined_instruction
a7800024 t _software_interrupt
a7800028 t _prefetch_abort
a780002c t _data_abort
a7800030 t _not_used
a7800034 t _irq
a7800038 t _fiq
...

Quoted 4 lines

Any Idea?

Chris

More info:
I'd compiled the hello_world
make[1]: Entering directory `/opt/cross_build/uboot.d/u-boot-git/examples/standalone' arm-linux-gnueabihf-gcc -g -Os -ffunction-sections -fdata-sections

(quoted diff) +0 -4
-fno-common -ffixed-r8 -msoft-float -D__KERNEL__
-DCONFIG_SYS_TEXT_BASE=0xa7800000 -DCONFIG_SPL_TEXT_BASE=0xa7400000
-DCONFIG_SPL_PAD_TO=5632 -I/opt/cross_build/uboot.d/u-boot-git/include
-fno-builtin -ffreestanding -nostdinc -isystem

/opt/armhf/gcc-linaro-arm-linux-gnueabihf-4.8-2013.07-1_linux/bin/../lib/gcc/arm-linux-gnueabihf/4.8.2/include

(quoted diff) +0 -4
-pipe -DCONFIG_ARM -D__ARM__ -marm -mno-thumb-interwork
-mabi=aapcs-linux -march=armv5te -Wall -Wstrict-prototypes
-fno-stack-protector -Wno-format-nonliteral -Wno-format-security
-fstack-usage -fno-toplevel-reorder -o hello_world.o hello_world.c -c

arm-linux-gnueabihf-gcc -g -Os -ffunction-sections -fdata-sections

(quoted diff) +0 -4
-fno-common -ffixed-r8 -msoft-float -D__KERNEL__
-DCONFIG_SYS_TEXT_BASE=0xa7800000 -DCONFIG_SPL_TEXT_BASE=0xa7400000
-DCONFIG_SPL_PAD_TO=5632 -I/opt/cross_build/uboot.d/u-boot-git/include
-fno-builtin -ffreestanding -nostdinc -isystem

/opt/armhf/gcc-linaro-arm-linux-gnueabihf-4.8-2013.07-1_linux/bin/../lib/gcc/arm-linux-gnueabihf/4.8.2/include

(quoted diff) +0 -4
-pipe -DCONFIG_ARM -D__ARM__ -marm -mno-thumb-interwork
-mabi=aapcs-linux -march=armv5te -Wall -Wstrict-prototypes
-fno-stack-protector -Wno-format-nonliteral -Wno-format-security
-fstack-usage -fno-toplevel-reorder -o stubs.o stubs.c -c

arm-linux-gnueabihf-ld.bfd -r -o libstubs.o stubs.o arm-linux-gnueabihf-ld.bfd -g -Ttext 0xa0000000 \

(quoted diff) +0 -3
-o hello_world -e hello_world hello_world.o libstubs.o \
-L/opt/armhf/gcc-linaro-arm-linux-gnueabihf-4.8-2013.07-1_linux/bin/../lib/gcc/arm-linux-gnueabihf/4.8.2
-lgcc

arm-linux-gnueabihf-objcopy -O srec hello_world hello_world.srec 2>/dev/null
arm-linux-gnueabihf-objcopy -O binary hello_world hello_world.bin 2>/dev/null

same, its not working

uboot:/ tftp hello_world.bin
phy0: Link is up - 100/Full
TFTP from server 10.128.2.105; our IP address is 10.128.2.10 Filename 'hello_world.bin'.
Loading: #
done
Bytes transferred = 590 (24e hex)
uboot:/ go hello_world.bin
memmap: Invalid argument
uboot:/ cp hello_world.bin /dev/ram0
uboot:/ go /dev/ram0
## Starting application at 0xA0000000 ...

Quoted 2 lines

Thanks for any hint.
Chris

Hi,

while I study the nand_spl.c jump to the mxc_nand_spl.c the page count is calculated ( page = from / CONFIG_SYS_NAND_PAGE_SIZE ) where from is the CONFIG_SYS_NAND_U_BOOT_OFFS

that means:
#define CONFIG_SPL_PAD_TO 6144 /* must match CONFIG_SYS_NAND_PAGE_SIZE boundery */ #define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SPL_PAD_TO

or some funny things happen to the u-boot.bin image in ram ..

comments welcome.

Chris

#3 lore raw
In reply to Chris Ruehl

Hi Chris,

Quoted 7 lines · Chris Ruehl

Hi.

I hope someone can open my eyes on this. We try to port our MX27 board to the new u-boot loader using the SPL code rather then the self hacked NAND->SDRAM.

I'm not able to get anything run. The console stays dead.

I would suggest you to look to an existing mx27 supported in mainline, like Armadeus' ap27 for example:

http://git.denx.de/?p=u-boot.git;a=commitdiff;h=bcc05c7aeb5507125b463fca3c98679d9c483919;hp=a8f2d0e6757c8f5391113582d8fecad29dc8cedc

Regards,

Fabio Estevam

#4 lore raw
Quoted 11 lines

Hi Chris,

Quoted 7 lines · Chris Ruehl

Hi.

I hope someone can open my eyes on this. We try to port our MX27 board to the new u-boot loader using the SPL code rather then the self hacked NAND->SDRAM.

I'm not able to get anything run. The console stays dead.

Quoted 8 lines

I would suggest you to look to an existing mx27 supported in mainline, like Armadeus' ap27 for example:

http://git.denx.de/?p=u-boot.git;a=commitdiff;h=bcc05c7aeb5507125b463fca3c98679d9c483919;hp=a8f2d0e6757c8f5391113582d8fecad29dc8cedc

Regards,

Fabio Estevam

Hi,

I had a quick look and many things match.. I think I have to spend a couple of days for study more details.

thanks
Chris