Skip to contentSkip to conversation

EXYNOS5420: Add SMDK5420 board support

PATCH Superseded Rajeshwari S Shinde 3 participants 16 messages Nov 15, 2013 – Nov 27, 2013 4 messages not in the archive

Subsystems (2)

v8 of 13 Superseded Latest is v13 →

lore
Share & tools
lore
#0 lore raw

v8 cover EXYNOS5420: Add SMDK5420 board support

This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.

Changes in V2:
- Corrected a compilation issue for SMDK5420.

Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.

Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.

Changes in V5:
- Moved functions board_mmc_init and board_eth_init to common/board.c in case of device tree support.

Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU to arch/arm dwmmc.h

Changes in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.

Changes in V8:
- corrected the if loops with if conditions of pro_id and cpu_id.

Rajeshwari S Shinde (9):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL support

 arch/arm/cpu/armv7/exynos/clock.c              | 258 ++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++-
 arch/arm/cpu/armv7/exynos/dmc_common.c         |  10 +-
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c      | 421 +++++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 738 +++++++++++++++++++------
 arch/arm/cpu/armv7/exynos/pinmux.c             | 260 ++++++++-
 arch/arm/dts/exynos5.dtsi                      | 198 +++++++
 arch/arm/dts/exynos5250.dtsi                   | 196 +------
 arch/arm/dts/exynos5420.dtsi                   |  70 +++
 arch/arm/include/asm/arch-exynos/board.h       |  17 +
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++++
 arch/arm/include/asm/arch-exynos/cpu.h         |  51 +-
 arch/arm/include/asm/arch-exynos/dmc.h         | 123 +++--
 arch/arm/include/asm/arch-exynos/gpio.h        | 143 ++++-
 arch/arm/include/asm/arch-exynos/periph.h      |   3 +
 board/samsung/common/Makefile                  |   4 +
 board/samsung/common/board.c                   | 407 ++++++++++++++
 board/samsung/dts/exynos5420-smdk5420.dts      | 169 ++++++
 board/samsung/smdk5250/exynos5-dt.c            | 361 +-----------
 board/samsung/smdk5250/smdk5250.c              | 182 +-----
 board/samsung/smdk5420/Makefile                |  34 ++
 board/samsung/smdk5420/smdk5420.c              | 159 ++++++
 board/samsung/smdk5420/smdk5420_spl.c          |  52 ++
 boards.cfg                                     |   1 +
 include/configs/arndale.h                      |   1 +
 include/configs/exynos5-dt.h                   | 300 ++++++++++
 include/configs/exynos5250-dt.h                | 316 +----------
 include/configs/smdk5420.h                     |  56 ++
 spl/Makefile                                   |   7 +-
 tools/Makefile                                 |   3 +-
 tools/mkexynosspl.c                            | 167 ++++--
 33 files changed, 4227 insertions(+), 1344 deletions(-)
 create mode 100644 arch/arm/dts/exynos5.dtsi
 create mode 100644 arch/arm/dts/exynos5420.dtsi
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c
 create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h
Signature · 1 line
1.7.12.4
#1 lore raw

PATCH v8 1/9 EXYNOS5: Create a common board file

Create a common board.c file for all functions which are common across all EXYNOS5 platforms.

exynos_init function is provided for platform specific code.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added check for the compilation of MAX77686 pmic.
Changes in V5:
- Moved board_eth_init and board_mmc_init in case of device tree support
Changes in V6:
- None.
Changes in V7:
- None
Changes in V8:
- None

 arch/arm/include/asm/arch-exynos/board.h |  17 ++
 board/samsung/common/Makefile            |   4 +
 board/samsung/common/board.c             | 405 +++++++++++++++++++++++++++++++
 board/samsung/smdk5250/exynos5-dt.c      | 361 +--------------------------
 board/samsung/smdk5250/smdk5250.c        | 182 +-------------
 include/configs/exynos5250-dt.h          |   2 +
 6 files changed, 435 insertions(+), 536 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c
arch/arm/include/asm/arch-exynos/board.h new file +17 -0
new file mode 100644
index 0000000..243fb12
@@ -0,0 +1,17 @@
+/*
+ * (C) Copyright 2013 Samsung Electronics
+ * Rajeshwari Shinde <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _EXYNOS_BOARD_H
+#define _EXYNOS_BOARD_H
+
+/*
+ * Exynos baord specific changes for
+ * board_init
+ */
+int exynos_init(void);
+
+#endif	/* EXYNOS_BOARD_H */
board/samsung/common/Makefile +4 -0
index 9e48a7b..eab8ab2 100644
@@ -11,6 +11,10 @@ LIB	= $(obj)libsamsung.o
 
 COBJS-$(CONFIG_SOFT_I2C_MULTI_BUS) += multi_i2c.o
 
+ifeq ($(CONFIG_SPL_BUILD),)
+COBJS-$(CONFIG_BOARD_COMMON)	+= board.o
+endif
+
 SRCS    := $(COBJS-y:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS-y))
 
board/samsung/common/board.c new file +405 -0

405 lines not on this page · raw message

board/samsung/smdk5250/exynos5-dt.c +4 -357

411 lines not on this page · raw message

board/samsung/smdk5250/smdk5250.c +3 -179

219 lines not on this page · raw message

include/configs/exynos5250-dt.h +2 -0
index 8c21909..3736ea8 100644
@@ -21,6 +21,8 @@
 #define CONFIG_ARCH_CPU_INIT
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_COMMON
+#define CONFIG_ARCH_EARLY_INIT_R
 
 /* Enable fdt support for Exynos5250 */
 #define CONFIG_OF_CONTROL
Signature · 1 line
1.7.12.4
#2 lore raw

PATCH v8 2/9 Exynos5420: Add base addresses for 5420

In reply to Rajeshwari S Shinde

Adds base addresses of various IPs and controllers required for Exynos5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added base address for TZPC.
Changes in V5:
- None
Chnages in V6:
- Rebased on latest samsung mainline branch.
Changes in V7:
- Corrected the comments
Changes in V8:
- None

 arch/arm/include/asm/arch-exynos/cpu.h | 47 +++++++++++++++++++++++++++++++++-
 1 file changed, 46 insertions(+), 1 deletion(-)
arch/arm/include/asm/arch-exynos/cpu.h +46 -1
index 4b67191..a465e6d 100644
@@ -88,7 +88,7 @@
 #define EXYNOS4X12_DMC_PHY_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS4X12_AUDIOSS_BASE		DEVICE_NOT_AVAILABLE
 
-/* EXYNOS5 Common*/
+/* EXYNOS5 */
 #define EXYNOS5_I2C_SPACING		0x10000
 
 #define EXYNOS5_AUDIOSS_BASE		0x03810000
@@ -124,6 +124,44 @@
 #define EXYNOS5_ADC_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS5_MODEM_BASE		DEVICE_NOT_AVAILABLE
 
+/* EXYNOS5420 */
+#define EXYNOS5420_AUDIOSS_BASE		0x03810000
+#define EXYNOS5420_GPIO_PART5_BASE	0x03860000
+#define EXYNOS5420_PRO_ID		0x10000000
+#define EXYNOS5420_CLOCK_BASE		0x10010000
+#define EXYNOS5420_POWER_BASE		0x10040000
+#define EXYNOS5420_SWRESET		0x10040400
+#define EXYNOS5420_SYSREG_BASE		0x10050000
+#define EXYNOS5420_TZPC_BASE		0x100E0000
+#define EXYNOS5420_WATCHDOG_BASE	0x101D0000
+#define EXYNOS5420_ACE_SFR_BASE		0x10830000
+#define EXYNOS5420_DMC_PHY_BASE		0x10C00000
+#define EXYNOS5420_DMC_CTRL_BASE	0x10C20000
+#define EXYNOS5420_DMC_TZASC0_BASE	0x10D40000
+#define EXYNOS5420_DMC_TZASC1_BASE	0x10D50000
+#define EXYNOS5420_USB_HOST_EHCI_BASE	0x12110000
+#define EXYNOS5420_MMC_BASE		0x12200000
+#define EXYNOS5420_SROMC_BASE		0x12250000
+#define EXYNOS5420_UART_BASE		0x12C00000
+#define EXYNOS5420_I2C_BASE		0x12C60000
+#define EXYNOS5420_I2C_8910_BASE	0x12E00000
+#define EXYNOS5420_SPI_BASE		0x12D20000
+#define EXYNOS5420_I2S_BASE		0x12D60000
+#define EXYNOS5420_PWMTIMER_BASE	0x12DD0000
+#define EXYNOS5420_SPI_ISP_BASE		0x131A0000
+#define EXYNOS5420_GPIO_PART2_BASE	0x13400000
+#define EXYNOS5420_GPIO_PART3_BASE	0x13410000
+#define EXYNOS5420_GPIO_PART4_BASE	0x14000000
+#define EXYNOS5420_GPIO_PART1_BASE	0x14010000
+#define EXYNOS5420_MIPI_DSIM_BASE	0x14500000
+#define EXYNOS5420_DP_BASE		0x145B0000
+
+#define EXYNOS5420_USBPHY_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_USBOTG_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_FIMD_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_ADC_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5420_MODEM_BASE		DEVICE_NOT_AVAILABLE
+
 #ifndef __ASSEMBLY__
 #include <asm/io.h>
 /* CPU detection macros */
@@ -157,6 +195,10 @@ static inline void s5p_set_cpu_id(void)
 		/* Exynos5250 */
 		s5p_cpu_id = 0x5250;
 		break;
+	case 0x420:
+		/* Exynos5420 */
+		s5p_cpu_id = 0x5420;
+		break;
 	}
 }
 
@@ -184,6 +226,7 @@ static inline int __attribute__((no_instrument_function)) \
 IS_EXYNOS_TYPE(exynos4210, 0x4210)
 IS_EXYNOS_TYPE(exynos4412, 0x4412)
 IS_EXYNOS_TYPE(exynos5250, 0x5250)
+IS_EXYNOS_TYPE(exynos5420, 0x5420)
 
 #define SAMSUNG_BASE(device, base)				\
 static inline unsigned int __attribute__((no_instrument_function)) \
@@ -194,6 +237,8 @@ static inline unsigned int __attribute__((no_instrument_function)) \
 			return EXYNOS4X12_##base;		\
 		return EXYNOS4_##base;				\
 	} else if (cpu_is_exynos5()) {				\
+		if (proid_is_exynos5420())			\
+			return EXYNOS5420_##base;		\
 		return EXYNOS5_##base;				\
 	}							\
 	return 0;						\
Signature · 1 line
1.7.12.4
#3 lore raw

PATCH v8 3/9 Exynos5420: Add clock initialization for 5420

In reply to Rajeshwari S Shinde

This patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Corrected the multiline commenting style
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Correct the logic for exynos5420_set_spi_clk api.
Changes in V8:
- Chnages the if condition loop for pro_id and cpu_id.

 arch/arm/cpu/armv7/exynos/clock.c              | 258 ++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 738 +++++++++++++++++++------
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++++
 6 files changed, 1659 insertions(+), 201 deletions(-)
arch/arm/cpu/armv7/exynos/clock.c +244 -14
index 36fedd6..f2f06ac 100644
@@ -96,7 +96,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k)
 
 	freq = CONFIG_SYS_CLK_FREQ;
 
-	if (pllreg == EPLL) {
+	if (pllreg == EPLL || pllreg == RPLL) {
 		k = k & 0xffff;
 		/* FOUT = (MDIV + K / 65536) * FIN / (PDIV * 2^SDIV) */
 		fout = (m + k / PLL_DIV_65536) * (freq / (p * (1 << s)));
@@ -117,7 +117,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k)
 			div = PLL_DIV_1024;
 		else if (proid_is_exynos4412())
 			div = PLL_DIV_65535;
-		else if (proid_is_exynos5250())
+		else if (proid_is_exynos5250() || proid_is_exynos5420())
 			div = PLL_DIV_65536;
 		else
 			return 0;
@@ -362,6 +362,43 @@ unsigned long clock_get_periph_rate(int peripheral)
 		return 0;
 }
 
+/* exynos5420: return pll clock frequency */
+static unsigned long exynos5420_get_pll_clk(int pllreg)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long r, k = 0;
+
+	switch (pllreg) {
+	case APLL:
+		r = readl(&clk->apll_con0);
+		break;
+	case MPLL:
+		r = readl(&clk->mpll_con0);
+		break;
+	case EPLL:
+		r = readl(&clk->epll_con0);
+		k = readl(&clk->epll_con1);
+		break;
+	case VPLL:
+		r = readl(&clk->vpll_con0);
+		k = readl(&clk->vpll_con1);
+		break;
+	case BPLL:
+		r = readl(&clk->bpll_con0);
+		break;
+	case RPLL:
+		r = readl(&clk->rpll_con0);
+		k = readl(&clk->rpll_con1);
+		break;
+	default:
+		printf("Unsupported PLL (%d)\n", pllreg);
+		return 0;
+	}
+
+	return exynos_get_pll_clk(pllreg, r, k);
+}
+
 /* exynos4: return ARM clock frequency */
 static unsigned long exynos4_get_arm_clk(void)
 {
@@ -485,6 +522,27 @@ static unsigned long exynos4x12_get_pwm_clk(void)
 	return pclk;
 }
 
+/* exynos5420: return pwm clock frequency */
+static unsigned long exynos5420_get_pwm_clk(void)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long pclk, sclk;
+	unsigned int ratio;
+
+	/*
+	 * CLK_DIV_PERIC3
+	 * PWM_RATIO [3:0]
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> 28) & 0xf;
+	sclk = get_pll_clk(MPLL);
+
+	pclk = sclk / (ratio + 1);
+
+	return pclk;
+}
+
 /* exynos4: return uart clock frequency */
 static unsigned long exynos4_get_uart_clk(int dev_index)
 {
@@ -624,6 +682,53 @@ static unsigned long exynos5_get_uart_clk(int dev_index)
 	return uclk;
 }
 
+/* exynos5420: return uart clock frequency */
+static unsigned long exynos5420_get_uart_clk(int dev_index)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel;
+	unsigned int ratio;
+
+	/*
+	 * CLK_SRC_PERIC0
+	 * UART0_SEL [3:0]
+	 * UART1_SEL [7:4]
+	 * UART2_SEL [8:11]
+	 * UART3_SEL [12:15]
+	 * UART4_SEL [16:19]
+	 * UART5_SEL [23:20]
+	 */
+	sel = readl(&clk->src_peric0);
+	sel = (sel >> ((dev_index * 4) + 4)) & 0x7;
+
+	if (sel == 0x3)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x6)
+		sclk = get_pll_clk(EPLL);
+	else if (sel == 0x7)
+		sclk = get_pll_clk(RPLL);
+	else
+		return 0;
+
+	/*
+	 * CLK_DIV_PERIC0
+	 * UART0_RATIO [3:0]
+	 * UART1_RATIO [7:4]
+	 * UART2_RATIO [8:11]
+	 * UART3_RATIO [12:15]
+	 * UART4_RATIO [16:19]
+	 * UART5_RATIO [23:20]
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> ((dev_index * 4) + 8)) & 0xf;
+
+	uclk = sclk / (ratio + 1);
+
+	return uclk;
+}
+
 static unsigned long exynos4_get_mmc_clk(int dev_index)
 {
 	struct exynos4_clock *clk =
@@ -718,6 +823,34 @@ static unsigned long exynos5_get_mmc_clk(int dev_index)
 	return uclk;
 }
 
+static unsigned long exynos5420_get_mmc_clk(int dev_index)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel, ratio;
+	int shift = 0;
+
+	sel = readl(&clk->src_fsys);
+	sel = (sel >> ((dev_index * 4) + 8)) & 0x7;
+
+	if (sel == 0x3)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x6)
+		sclk = get_pll_clk(EPLL);
+	else
+		return 0;
+
+	ratio = readl(&clk->div_fsys1);
+
+	shift = dev_index * 10;
+
+	ratio = (ratio >> shift) & 0x3ff;
+	uclk = (sclk / (ratio + 1));
+
+	return uclk;
+}
+
 /* exynos4: set the mmc clock */
 static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
 {
@@ -804,6 +937,23 @@ static void exynos5_set_mmc_clk(int dev_index, unsigned int div)
 	writel(val, addr);
 }
 
+/* exynos5: set the mmc clock */
+static void exynos5420_set_mmc_clk(int dev_index, unsigned int div)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned int addr;
+	unsigned int val, shift;
+
+	addr = (unsigned int)&clk->div_fsys1;
+	shift = dev_index * 10;
+
+	val = readl(addr);
+	val &= ~(0x3ff << shift);
+	val |= (div & 0x3ff) << shift;
+	writel(val, addr);
+}
+
 /* get_lcd_clk: return lcd clock frequency */
 static unsigned long exynos4_get_lcd_clk(void)
 {
@@ -1324,6 +1474,72 @@ static int exynos5_set_spi_clk(enum periph_id periph_id,
 	return 0;
 }
 
+static int exynos5420_set_spi_clk(enum periph_id periph_id,
+					unsigned int rate)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	int main;
+	unsigned int fine;
+	unsigned shift, pre_shift;
+	unsigned div_mask = 0xf, pre_div_mask = 0xff;
+	u32 *reg;
+	u32 *pre_reg;
+
+
+	main = clock_calc_best_scalar(4, 8, 400000000, rate, &fine);
+	if (main < 0) {
+		debug("%s: Cannot set clock rate for periph %d",
+		      __func__, periph_id);
+		return -1;
+	}
+	main = main - 1;
+	fine = fine - 1;
+
+	switch (periph_id) {
+	case PERIPH_ID_SPI0:
+		reg = &clk->div_peric1;
+		shift = 20;
+		pre_reg = &clk->div_peric4;
+		pre_shift = 8;
+		break;
+	case PERIPH_ID_SPI1:
+		reg = &clk->div_peric1;
+		shift = 24;
+		pre_reg = &clk->div_peric4;
+		pre_shift = 16;
+		break;
+	case PERIPH_ID_SPI2:
+		reg = &clk->div_peric1;
+		shift = 28;
+		pre_reg = &clk->div_peric4;
+		pre_shift = 24;
+		break;
+	case PERIPH_ID_SPI3:
+		reg = &clk->div_isp1;
+		shift = 16;
+		pre_reg = &clk->div_isp1;
+		pre_shift = 0;
+		break;
+	case PERIPH_ID_SPI4:
+		reg = &clk->div_isp1;
+		shift = 20;
+		pre_reg = &clk->div_isp1;
+		pre_shift = 8;
+		break;
+	default:
+		debug("%s: Unsupported peripheral ID %d\n", __func__,
+		      periph_id);
+		return -1;
+	}
+
+	clrsetbits_le32(reg, div_mask << shift, (main & div_mask) << shift);
+	clrsetbits_le32(pre_reg, pre_div_mask << pre_shift,
+			(fine & pre_div_mask) << pre_shift);
+
+	return 0;
+}
+
 static unsigned long exynos4_get_i2c_clk(void)
 {
 	struct exynos4_clock *clk =
@@ -1341,9 +1557,11 @@ static unsigned long exynos4_get_i2c_clk(void)
 
 unsigned long get_pll_clk(int pllreg)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_pll_clk(pllreg);
 		return exynos5_get_pll_clk(pllreg);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_pll_clk(pllreg);
 		return exynos4_get_pll_clk(pllreg);
@@ -1375,9 +1593,11 @@ unsigned long get_i2c_clk(void)
 
 unsigned long get_pwm_clk(void)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_pwm_clk();
 		return clock_get_periph_rate(PERIPH_ID_PWM0);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_pwm_clk();
 		return exynos4_get_pwm_clk();
@@ -1386,9 +1606,11 @@ unsigned long get_pwm_clk(void)
 
 unsigned long get_uart_clk(int dev_index)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_uart_clk(dev_index);
 		return exynos5_get_uart_clk(dev_index);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_uart_clk(dev_index);
 		return exynos4_get_uart_clk(dev_index);
@@ -1397,17 +1619,22 @@ unsigned long get_uart_clk(int dev_index)
 
 unsigned long get_mmc_clk(int dev_index)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_mmc_clk(dev_index);
 		return exynos5_get_mmc_clk(dev_index);
-	else
+	} else {
 		return exynos4_get_mmc_clk(dev_index);
+	}
 }
 
 void set_mmc_clk(int dev_index, unsigned int div)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_set_mmc_clk(dev_index, div);
 		exynos5_set_mmc_clk(dev_index, div);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			exynos4x12_set_mmc_clk(dev_index, div);
 		exynos4_set_mmc_clk(dev_index, div);
@@ -1438,10 +1665,13 @@ void set_mipi_clk(void)
 
 int set_spi_clk(int periph_id, unsigned int rate)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_set_spi_clk(periph_id, rate);
 		return exynos5_set_spi_clk(periph_id, rate);
-	else
+	} else {
 		return 0;
+	}
 }
 
 int set_i2s_clk_prescaler(unsigned int src_frq, unsigned int dst_frq,
arch/arm/cpu/armv7/exynos/clock_init.h +17 -0
index c28ff3a..a875d0b 100644
@@ -10,7 +10,11 @@
 #define __EXYNOS_CLOCK_INIT_H
 
 enum {
+#ifdef CONFIG_EXYNOS5420
+	MEM_TIMINGS_MSR_COUNT	= 5,
+#else
 	MEM_TIMINGS_MSR_COUNT	= 4,
+#endif
 };
 
 /* These are the ratio's for configuring ARM clock */
@@ -59,6 +63,18 @@ struct mem_timings {
 	unsigned bpll_mdiv;
 	unsigned bpll_pdiv;
 	unsigned bpll_sdiv;
+	unsigned kpll_mdiv;
+	unsigned kpll_pdiv;
+	unsigned kpll_sdiv;
+	unsigned dpll_mdiv;
+	unsigned dpll_pdiv;
+	unsigned dpll_sdiv;
+	unsigned ipll_mdiv;
+	unsigned ipll_pdiv;
+	unsigned ipll_sdiv;
+	unsigned spll_mdiv;
+	unsigned spll_pdiv;
+	unsigned spll_sdiv;
 	unsigned pclk_cdrex_ratio;
 	unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
 
@@ -115,6 +131,7 @@ struct mem_timings {
 	uint8_t send_zq_init;		/* 1 to send this command */
 	unsigned impedance;		/* drive strength impedeance */
 	uint8_t gate_leveling_enable;	/* check gate leveling is enabled */
+	uint8_t read_leveling_enable;	/* check h/w read leveling is enabled */
 };
 
 /**
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +338 -14

390 lines not on this page · raw message

arch/arm/cpu/armv7/exynos/exynos5_setup.h +565 -173

854 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/clk.h +1 -0
index 1d6fa93..cdeef32 100644
@@ -14,6 +14,7 @@
 #define HPLL	3
 #define VPLL	4
 #define BPLL	5
+#define RPLL	6
 
 enum pll_src_bit {
 	EXYNOS_SRC_MPLL = 6,
arch/arm/include/asm/arch-exynos/clock.h +494 -0

500 lines not on this page · raw message

Signature · 1 line
1.7.12.4

A message that is not in the archive (sent off-list or not yet received): [email protected]

#5 lore raw

PATCH v8 3/9 Exynos5420: Add clock initialization for 5420

ping.

-------- Original Message --------
Subject: Re: [PATCH 3/9 v8] Exynos5420: Add clock initialization for 5420
Date: Thu, 21 Nov 2013 16:03:23 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com

Dear Rajeshwari,

Quoted 237 lines · Rajeshwari S Shinde

This patch adds code for clock initialization and clock settings of various IP's and controllers, required for Exynos5420

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Corrected the multiline commenting style
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Correct the logic for exynos5420_set_spi_clk api.
Changes in V8:
- Chnages the if condition loop for pro_id and cpu_id.

 arch/arm/cpu/armv7/exynos/clock.c              | 258 ++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 738 +++++++++++++++++++------
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++++
 6 files changed, 1659 insertions(+), 201 deletions(-)
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +152 -14
index a24c2f3..e7f1496 100644
@@ -24,6 +24,24 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 struct arm_clk_ratios arm_clk_ratios[] = {
+#ifdef CONFIG_EXYNOS5420
+	{
+		.arm_freq_mhz = 900,
+
+		.apll_mdiv = 0x96,
+		.apll_pdiv = 0x2,
+		.apll_sdiv = 0x1,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x6,
+		.atb_ratio = 0x6,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x0,
+		.cpud_ratio = 0x2,
+		.arm_ratio = 0x0,
+	}
+#else
 	{
 		.arm_freq_mhz = 600,
 
@@ -115,8 +133,133 @@ struct arm_clk_ratios arm_clk_ratios[] = {
 		.cpud_ratio = 0x3,
 		.arm_ratio = 0x0,
 	}
+#endif
 };
+
 struct mem_timings mem_timings[] = {
+#ifdef CONFIG_EXYNOS5420
+	{
+		.mem_manuf = MEM_MANUF_SAMSUNG,
+		.mem_type = DDR_MODE_DDR3,
+		.frequency_mhz = 800,
+
+		/* MPLL @800MHz*/
+		.mpll_mdiv = 0xc8,
+		.mpll_pdiv = 0x3,
+		.mpll_sdiv = 0x1,
+		/* CPLL @666MHz */
+		.cpll_mdiv = 0xde,
+		.cpll_pdiv = 0x4,
+		.cpll_sdiv = 0x1,
+		/* EPLL @600MHz */
+		.epll_mdiv = 0x64,
+		.epll_pdiv = 0x2,
+		.epll_sdiv = 0x1,
+		/* VPLL @430MHz */
+		.vpll_mdiv = 0xd7,
+		.vpll_pdiv = 0x3,
+		.vpll_sdiv = 0x2,
+		/* BPLL @800MHz */
+		.bpll_mdiv = 0xc8,
+		.bpll_pdiv = 0x3,
+		.bpll_sdiv = 0x1,
+		/* KPLL @600MHz */
+		.kpll_mdiv = 0x190,
+		.kpll_pdiv = 0x4,
+		.kpll_sdiv = 0x2,
+		/* DPLL @600MHz */
+		.dpll_mdiv = 0x190,
+		.dpll_pdiv = 0x4,
+		.dpll_sdiv = 0x2,
+		/* IPLL @370MHz */
+		.ipll_mdiv = 0xb9,
+		.ipll_pdiv = 0x3,
+		.ipll_sdiv = 0x2,
+		/* SPLL @400MHz */
+		.spll_mdiv = 0xc8,
+		.spll_pdiv = 0x3,
+		.spll_sdiv = 0x2,
+
+		.direct_cmd_msr = {
+			0x00020018, 0x00030000, 0x00010046, 0x00000d70,
+			0x00000c70
+		},
+		.timing_ref = 0x000000bb,
+		.timing_row = 0x6836650f,
+		.timing_data = 0x3630580b,
+		.timing_power = 0x41000a26,
+		.phy0_dqs = 0x08080808,
+		.phy1_dqs = 0x08080808,
+		.phy0_dq = 0x08080808,
+		.phy1_dq = 0x08080808,
+		.phy0_tFS = 0x8,
+		.phy1_tFS = 0x8,
+		.phy0_pulld_dqs = 0xf,
+		.phy1_pulld_dqs = 0xf,
+
+		.lpddr3_ctrl_phy_reset = 0x1,
+		.ctrl_start_point = 0x10,
+		.ctrl_inc = 0x10,
+		.ctrl_start = 0x1,
+		.ctrl_dll_on = 0x1,
+		.ctrl_ref = 0x8,
+
+		.ctrl_force = 0x1a,
+		.ctrl_rdlat = 0x0b,
+		.ctrl_bstlen = 0x08,
+
+		.fp_resync = 0x8,
+		.iv_size = 0x7,
+		.dfi_init_start = 1,
+		.aref_en = 1,
+
+		.rd_fetch = 0x3,
+
+		.zq_mode_dds = 0x7,
+		.zq_mode_term = 0x1,
+		.zq_mode_noterm = 1,
+
+		/*
+		* Dynamic Clock: Always Running
+		* Memory Burst length: 8
+		* Number of chips: 1
+		* Memory Bus width: 32 bit
+		* Memory Type: DDR3
+		* Additional Latancy for PLL: 0 Cycle
+		*/
+		.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+			DMC_MEMCONTROL_TP_DISABLE |
+			DMC_MEMCONTROL_DSREF_DISABLE |
+			DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+			DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+			DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+			DMC_MEMCONTROL_NUM_CHIP_1 |
+			DMC_MEMCONTROL_BL_8 |
+			DMC_MEMCONTROL_PZQ_DISABLE |
+			DMC_MEMCONTROL_MRR_BYTE_7_0,
+		.memconfig = DMC_MEMCONFIG_CHIP_MAP_SPLIT |
+			DMC_MEMCONFIGX_CHIP_COL_10 |
+			DMC_MEMCONFIGX_CHIP_ROW_15 |
+			DMC_MEMCONFIGX_CHIP_BANK_8,
+		.prechconfig_tp_cnt = 0xff,
+		.dpwrdn_cyc = 0xff,
+		.dsref_cyc = 0xffff,
+		.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+			DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+			DMC_CONCONTROL_RD_FETCH_DISABLE |
+			DMC_CONCONTROL_EMPTY_DISABLE |
+			DMC_CONCONTROL_AREF_EN_DISABLE |
+			DMC_CONCONTROL_IO_PD_CON_DISABLE,
+		.dmc_channels = 1,
+		.chips_per_channel = 1,
+		.chips_to_configure = 1,
+		.send_zq_init = 1,
+		.gate_leveling_enable = 1,
+		.read_leveling_enable = 0,
+	}
+#else
 	{
 		.mem_manuf = MEM_MANUF_ELPIDA,
 		.mem_type = DDR_MODE_DDR3,
@@ -324,6 +467,7 @@ struct mem_timings mem_timings[] = {
 		.impedance = IMP_OUTPUT_DRV_40_OHM,
 		.gate_leveling_enable = 1,
 	}
+#endif
 };
 
 /**
@@ -399,7 +543,7 @@ struct mem_timings *clock_get_mem_timings(void)
 	return NULL;
 }
 
-void system_clock_init()
+static void exynos5250_system_clock_init(void)
 {
 	struct exynos5_clock *clk =
 		(struct exynos5_clock *)samsung_get_base_clock();
@@ -436,19 +580,13 @@ void system_clock_init()
 	} while ((val | MUX_BPLL_SEL_MASK) != val);
 
 	/* PLL locktime */
-	writel(APLL_LOCK_VAL, &clk->apll_lock);
-
-	writel(MPLL_LOCK_VAL, &clk->mpll_lock);
-
-	writel(BPLL_LOCK_VAL, &clk->bpll_lock);
-
-	writel(CPLL_LOCK_VAL, &clk->cpll_lock);
-
-	writel(GPLL_LOCK_VAL, &clk->gpll_lock);
-
-	writel(EPLL_LOCK_VAL, &clk->epll_lock);
-
-	writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+	writel(mem->apll_pdiv * PLL_LOCK_FACTOR, &clk->apll_lock);
+	writel(mem->mpll_pdiv * PLL_LOCK_FACTOR, &clk->mpll_lock);
+	writel(mem->bpll_pdiv * PLL_LOCK_FACTOR, &clk->bpll_lock);
+	writel(mem->cpll_pdiv * PLL_LOCK_FACTOR, &clk->cpll_lock);
+	writel(mem->gpll_pdiv * PLL_X_LOCK_FACTOR, &clk->gpll_lock);
+	writel(mem->epll_pdiv * PLL_X_LOCK_FACTOR, &clk->epll_lock);
+	writel(mem->vpll_pdiv * PLL_X_LOCK_FACTOR, &clk->vpll_lock);
 
 	writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
 

arch/arm/cpu/armv7/exynos/clock_init_exynos5.c void system_clock_init() · line 784

Quoted 7 lines
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +4 -0
@@ -640,6 +778,192 @@ void system_clock_init()
 	writel(val, &clk->div_fsys2);
 }
 
+static void exynos5420_system_clock_init(void)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)EXYNOS5_CLOCK_BASE;

samsung_get_base_clock();

Quoted 175 lines
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +175 -0
+	struct mem_timings *mem;
+	struct arm_clk_ratios *arm_clk_ratio;
+	u32 val;
+
+	mem = clock_get_mem_timings();
+	arm_clk_ratio = get_arm_ratios();
+
+	/* PLL locktime */
+	writel(arm_clk_ratio->apll_pdiv * PLL_LOCK_FACTOR, &clk->apll_lock);
+	writel(mem->mpll_pdiv * PLL_LOCK_FACTOR, &clk->mpll_lock);
+	writel(mem->bpll_pdiv * PLL_LOCK_FACTOR, &clk->bpll_lock);
+	writel(mem->cpll_pdiv * PLL_LOCK_FACTOR, &clk->cpll_lock);
+	writel(mem->dpll_pdiv * PLL_LOCK_FACTOR, &clk->dpll_lock);
+	writel(mem->epll_pdiv * PLL_X_LOCK_FACTOR, &clk->epll_lock);
+	writel(mem->vpll_pdiv * PLL_LOCK_FACTOR, &clk->vpll_lock);
+	writel(mem->ipll_pdiv * PLL_LOCK_FACTOR, &clk->ipll_lock);
+	writel(mem->spll_pdiv * PLL_LOCK_FACTOR, &clk->spll_lock);
+	writel(mem->kpll_pdiv * PLL_LOCK_FACTOR, &clk->kpll_lock);
+
+	setbits_le32(&clk->src_cpu, MUX_HPM_SEL_MASK);
+
+	writel(0, &clk->src_top6);
+
+	writel(0, &clk->src_cdrex);
+	writel(SRC_KFC_HPM_SEL, &clk->src_kfc);
+	writel(HPM_RATIO,  &clk->div_cpu1);
+	writel(CLK_DIV_CPU0_VAL,  &clk->div_cpu0);
+
+	/* switch A15 clock source to OSC clock before changing APLL */
+	clrbits_le32(&clk->src_cpu, APLL_FOUT);
+
+	/* Set APLL */
+	writel(APLL_CON1_VAL, &clk->apll_con1);
+	val = set_pll(arm_clk_ratio->apll_mdiv,
+		      arm_clk_ratio->apll_pdiv,
+		      arm_clk_ratio->apll_sdiv);
+	writel(val, &clk->apll_con0);
+	while ((readl(&clk->apll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* now it is safe to switch to APLL */
+	setbits_le32(&clk->src_cpu, APLL_FOUT);
+
+	writel(SRC_KFC_HPM_SEL, &clk->src_kfc);
+	writel(CLK_DIV_KFC_VAL, &clk->div_kfc0);
+
+	/* switch A7 clock source to OSC clock before changing KPLL */
+	clrbits_le32(&clk->src_kfc, KPLL_FOUT);
+
+	/* Set KPLL*/
+	writel(KPLL_CON1_VAL, &clk->kpll_con1);
+	val = set_pll(mem->kpll_mdiv, mem->kpll_pdiv, mem->kpll_sdiv);
+	writel(val, &clk->kpll_con0);
+	while ((readl(&clk->kpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* now it is safe to switch to KPLL */
+	setbits_le32(&clk->src_kfc, KPLL_FOUT);
+
+	/* Set MPLL */
+	writel(MPLL_CON1_VAL, &clk->mpll_con1);
+	val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
+	writel(val, &clk->mpll_con0);
+	while ((readl(&clk->mpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set DPLL */
+	writel(DPLL_CON1_VAL, &clk->dpll_con1);
+	val = set_pll(mem->dpll_mdiv, mem->dpll_pdiv, mem->dpll_sdiv);
+	writel(val, &clk->dpll_con0);
+	while ((readl(&clk->dpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set EPLL */
+	writel(EPLL_CON2_VAL, &clk->epll_con2);
+	writel(EPLL_CON1_VAL, &clk->epll_con1);
+	val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
+	writel(val, &clk->epll_con0);
+	while ((readl(&clk->epll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set CPLL */
+	writel(CPLL_CON1_VAL, &clk->cpll_con1);
+	val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
+	writel(val, &clk->cpll_con0);
+	while ((readl(&clk->cpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set IPLL */
+	writel(IPLL_CON1_VAL, &clk->ipll_con1);
+	val = set_pll(mem->ipll_mdiv, mem->ipll_pdiv, mem->ipll_sdiv);
+	writel(val, &clk->ipll_con0);
+	while ((readl(&clk->ipll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set VPLL */
+	writel(VPLL_CON1_VAL, &clk->vpll_con1);
+	val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
+	writel(val, &clk->vpll_con0);
+	while ((readl(&clk->vpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set BPLL */
+	writel(BPLL_CON1_VAL, &clk->bpll_con1);
+	val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
+	writel(val, &clk->bpll_con0);
+	while ((readl(&clk->bpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set SPLL */
+	writel(SPLL_CON1_VAL, &clk->spll_con1);
+	val = set_pll(mem->spll_mdiv, mem->spll_pdiv, mem->spll_sdiv);
+	writel(val, &clk->spll_con0);
+	while ((readl(&clk->spll_con0) & PLL_LOCKED) == 0)
+		;
+
+	writel(CLK_DIV_CDREX0_VAL, &clk->div_cdrex0);
+	writel(CLK_DIV_CDREX1_VAL, &clk->div_cdrex1);
+
+	writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+	writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+	writel(CLK_SRC_TOP2_VAL, &clk->src_top2);
+	writel(CLK_SRC_TOP7_VAL, &clk->src_top7);
+
+	writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+	writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+	writel(CLK_DIV_TOP2_VAL, &clk->div_top2);
+
+	writel(0, &clk->src_top10);
+	writel(0, &clk->src_top11);
+	writel(0, &clk->src_top12);
+
+	writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
+	writel(CLK_SRC_TOP4_VAL, &clk->src_top4);
+	writel(CLK_SRC_TOP5_VAL, &clk->src_top5);
+
+	/* DISP1 BLK CLK SELECTION */
+	writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp10);
+	writel(CLK_DIV_DISP1_0_VAL, &clk->div_disp10);
+
+	/* AUDIO BLK */
+	writel(AUDIO0_SEL_EPLL, &clk->src_mau);
+	writel(DIV_MAU_VAL, &clk->div_mau);
+
+	/* FSYS */
+	writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
+	writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+	writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
+	writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
+
+	writel(CLK_SRC_ISP_VAL, &clk->src_isp);
+	writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+	writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+
+	writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+	writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
+
+	writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
+	writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
+	writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
+	writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
+	writel(CLK_DIV_PERIC4_VAL, &clk->div_peric4);
+
+	writel(CLK_DIV_CPERI1_VAL, &clk->div_cperi1);
+
+	writel(CLK_DIV2_RATIO, &clk->clkdiv2_ratio);
+	writel(CLK_DIV4_RATIO, &clk->clkdiv4_ratio);
+	writel(CLK_DIV_G2D, &clk->div_g2d);
+
+	writel(CLK_SRC_TOP6_VAL, &clk->src_top6);
+	writel(CLK_SRC_CDREX_VAL, &clk->src_cdrex);
+	writel(CLK_SRC_KFC_VAL, &clk->src_kfc);
+}
+
+void system_clock_init(void)

arch/arm/cpu/armv7/exynos/clock_init_exynos5.c void system_clock_init() · line 969

Quoted 10 lines
arch/arm/cpu/armv7/exynos/clock_init_exynos5.c +7 -0
+{
+	if (proid_is_exynos5420())
+		exynos5420_system_clock_init();
+	else
+		exynos5250_system_clock_init();
+}
+
 void clock_init_dp_clock(void)
 {
 	struct exynos5_clock *clk =

Thanks,
Minkyu Kang.

#6 lore raw

PATCH v8 4/9 Exynos5420: Add DDR3 initialization for 5420

In reply to Rajeshwari S Shinde

This patch intends to add DDR3 initialization code for Exynos5420.

---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- None

 arch/arm/cpu/armv7/exynos/dmc_common.c    |  10 +-
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++++++++++++++++++-
 arch/arm/include/asm/arch-exynos/cpu.h    |   4 +
 arch/arm/include/asm/arch-exynos/dmc.h    | 123 ++++++---
 4 files changed, 513 insertions(+), 45 deletions(-)
arch/arm/cpu/armv7/exynos/dmc_common.c +1 -9
index 53cfe6e..9e432c2 100644
@@ -1,5 +1,5 @@
 /*
- * Mem setup common file for different types of DDR present on SMDK5250 boards.
+ * Mem setup common file for different types of DDR present on Exynos boards.
  *
  * Copyright (C) 2012 Samsung Electronics
  *
@@ -152,14 +152,6 @@ void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
 	}
 }
 
-void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
-{
-	writel(mem->memconfig, &dmc->memconfig0);
-	writel(mem->memconfig, &dmc->memconfig1);
-	writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
-	writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
-}
-
 void mem_ctrl_init(int reset)
 {
 	struct spl_machine_param *param = spl_get_machine_params();
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +417 -4

447 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/cpu.h +4 -0
index a465e6d..c7f4a5e 100644
@@ -162,6 +162,10 @@
 #define EXYNOS5420_ADC_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS5420_MODEM_BASE		DEVICE_NOT_AVAILABLE
 
+#define PAD_RETENTION_DRAM_STATUS	(EXYNOS5420_POWER_BASE + 0x3004)
+#define PAD_RETENTION_DRAM_COREBLK_OPTION	(EXYNOS5420_POWER_BASE + 0x31E8)
+#define PAD_RETENTION_DRAM_COREBLK_VAL	0x10000000
+
 #ifndef __ASSEMBLY__
 #include <asm/io.h>
 /* CPU detection macros */
arch/arm/include/asm/arch-exynos/dmc.h +91 -32

186 lines not on this page · raw message

Signature · 1 line
1.7.12.4

A message that is not in the archive (sent off-list or not yet received): [email protected]

#8 lore raw

PATCH v8 4/9 Exynos5420: Add DDR3 initialization for 5420

ping.

-------- Original Message --------
Subject: Re: [PATCH 4/9 v8] Exynos5420: Add DDR3 initialization for 5420
Date: Thu, 21 Nov 2013 16:13:24 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com

Dear Rajeshwari,

Quoted 94 lines · Rajeshwari S Shinde

This patch intends to add DDR3 initialization code for Exynos5420.

---
Changes in V2:
- Corrected a compilation issue for SMDK5250.
Changes in V3:
- None
Changes in V4:
- None
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Fixed multi line comment.
Changes in V8:
- None

 arch/arm/cpu/armv7/exynos/dmc_common.c    |  10 +-
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c | 421 +++++++++++++++++++++++++++++-
 arch/arm/include/asm/arch-exynos/cpu.h    |   4 +
 arch/arm/include/asm/arch-exynos/dmc.h    | 123 ++++++---
 4 files changed, 513 insertions(+), 45 deletions(-)
arch/arm/cpu/armv7/exynos/dmc_common.c +1 -9
index 53cfe6e..9e432c2 100644
@@ -1,5 +1,5 @@
 /*
- * Mem setup common file for different types of DDR present on SMDK5250 boards.
+ * Mem setup common file for different types of DDR present on Exynos boards.
  *
  * Copyright (C) 2012 Samsung Electronics
  *
@@ -152,14 +152,6 @@ void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
 	}
 }
 
-void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
-{
-	writel(mem->memconfig, &dmc->memconfig0);
-	writel(mem->memconfig, &dmc->memconfig1);
-	writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
-	writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
-}
-
 void mem_ctrl_init(int reset)
 {
 	struct spl_machine_param *param = spl_get_machine_params();
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +5 -4
index 5f5914e..3fab50b 100644
@@ -1,5 +1,5 @@
 /*
- * DDR3 mem setup file for SMDK5250 board based on EXYNOS5
+ * DDR3 mem setup file for board based on EXYNOS5
  *
  * Copyright (C) 2012 Samsung Electronics
  *
@@ -15,8 +15,9 @@
 #include "exynos5_setup.h"
 #include "clock_init.h"
 
-#define RDLVL_COMPLETE_TIMEOUT	10000
+#define TIMEOUT	10000
 
+#ifdef CONFIG_EXYNOS5250
 static void reset_phy_ctrl(void)
 {
 	struct exynos5_clock *clk =
@@ -108,7 +109,7 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
 
 	/* Precharge Configuration */
 	writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
-	       &dmc->prechconfig);
+	       &dmc->prechconfig0);
 
 	/* Power Down mode Configuration */
 	writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
@@ -174,7 +175,7 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
 		writel(val, &phy1_ctrl->phy_con1);
 
 		writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
-		i = RDLVL_COMPLETE_TIMEOUT;
+		i = TIMEOUT;
 		while ((readl(&dmc->phystatus) &
 			(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
 			(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
@@ -215,3 +216,415 @@ int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
 		| (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);

arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size, · line 226

Quoted 10 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +8 -0
 	return 0;
 }
+#endif
+
+#ifdef CONFIG_EXYNOS5420
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
+		       int reset)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)EXYNOS5_CLOCK_BASE;

samsung_get_base_clock();

Quoted 5 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +5 -0
+	struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
+	struct exynos5_dmc *drex0, *drex1;
+	struct exynos5_tzasc *tzasc0, *tzasc1;
+	uint32_t val, n_lock_r, n_lock_w_phy0, n_lock_w_phy1;
+	int chip;

arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size, · line 241

Quoted 10 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +10 -0
+	int i;
+
+	phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy();
+	phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy()
+							+ DMC_OFFSET);
+	drex0 = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl();
+	drex1 = (struct exynos5_dmc *)(samsung_get_base_dmc_ctrl()
+							+ DMC_OFFSET);
+	tzasc0 = (struct exynos5_tzasc *)EXYNOS5420_DMC_TZASC0_BASE;
+	tzasc1 = (struct exynos5_tzasc *)EXYNOS5420_DMC_TZASC1_BASE;

No, we don't allow direct access to the base adress.

Quoted 394 lines
arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c +389 -0
+
+	/* Enable PAUSE for DREX */
+	setbits_le32(&clk->pause, ENABLE_BIT);
+
+	/* Enable BYPASS mode */
+	setbits_le32(&clk->bpll_con1, BYPASS_EN);
+
+	writel(MUX_BPLL_SEL_FOUTBPLL, &clk->src_cdrex);
+	do {
+		val = readl(&clk->mux_stat_cdrex);
+		val &= BPLL_SEL_MASK;
+	} while (val != FOUTBPLL);
+
+	clrbits_le32(&clk->bpll_con1, BYPASS_EN);
+
+	/* Specify the DDR memory type as DDR3 */
+	val = readl(&phy0_ctrl->phy_con0);
+	val &= ~(PHY_CON0_CTRL_DDR_MODE_MASK << PHY_CON0_CTRL_DDR_MODE_SHIFT);
+	val |= (DDR_MODE_DDR3 << PHY_CON0_CTRL_DDR_MODE_SHIFT);
+	writel(val, &phy0_ctrl->phy_con0);
+
+	val = readl(&phy1_ctrl->phy_con0);
+	val &= ~(PHY_CON0_CTRL_DDR_MODE_MASK << PHY_CON0_CTRL_DDR_MODE_SHIFT);
+	val |= (DDR_MODE_DDR3 << PHY_CON0_CTRL_DDR_MODE_SHIFT);
+	writel(val, &phy1_ctrl->phy_con0);
+
+	/* Set Read Latency and Burst Length for PHY0 and PHY1 */
+	val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
+		(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
+	writel(val, &phy0_ctrl->phy_con42);
+	writel(val, &phy1_ctrl->phy_con42);
+
+	val = readl(&phy0_ctrl->phy_con26);
+	val &= ~(T_WRDATA_EN_MASK << T_WRDATA_EN_OFFSET);
+	val |= (T_WRDATA_EN_DDR3 << T_WRDATA_EN_OFFSET);
+	writel(val, &phy0_ctrl->phy_con26);
+
+	val = readl(&phy1_ctrl->phy_con26);
+	val &= ~(T_WRDATA_EN_MASK << T_WRDATA_EN_OFFSET);
+	val |= (T_WRDATA_EN_DDR3 << T_WRDATA_EN_OFFSET);
+	writel(val, &phy1_ctrl->phy_con26);
+
+	/*
+	 * Set Driver strength for CK, CKE, CS & CA to 0x7
+	 * Set Driver strength for Data Slice 0~3 to 0x7
+	 */
+	val = (0x7 << CA_CK_DRVR_DS_OFFSET) | (0x7 << CA_CKE_DRVR_DS_OFFSET) |
+		(0x7 << CA_CS_DRVR_DS_OFFSET) | (0x7 << CA_ADR_DRVR_DS_OFFSET);
+	val |= (0x7 << DA_3_DS_OFFSET) | (0x7 << DA_2_DS_OFFSET) |
+		(0x7 << DA_1_DS_OFFSET) | (0x7 << DA_0_DS_OFFSET);
+	writel(val, &phy0_ctrl->phy_con39);
+	writel(val, &phy1_ctrl->phy_con39);
+
+	/* ZQ Calibration */
+	if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
+		return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
+
+	clrbits_le32(&phy0_ctrl->phy_con16, ZQ_CLK_DIV_EN);
+	clrbits_le32(&phy1_ctrl->phy_con16, ZQ_CLK_DIV_EN);
+
+	/* DQ Signal */
+	val = readl(&phy0_ctrl->phy_con14);
+	val |= mem->phy0_pulld_dqs;
+	writel(val, &phy0_ctrl->phy_con14);
+	val = readl(&phy1_ctrl->phy_con14);
+	val |= mem->phy1_pulld_dqs;
+	writel(val, &phy1_ctrl->phy_con14);
+
+	val = MEM_TERM_EN | PHY_TERM_EN;
+	writel(val, &drex0->phycontrol0);
+	writel(val, &drex1->phycontrol0);
+
+	writel(mem->concontrol |
+		(mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT) |
+		(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
+		&drex0->concontrol);
+	writel(mem->concontrol |
+		(mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT) |
+		(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
+		&drex1->concontrol);
+
+	do {
+		val = readl(&drex0->phystatus);
+	} while ((val & DFI_INIT_COMPLETE) != DFI_INIT_COMPLETE);
+	do {
+		val = readl(&drex1->phystatus);
+	} while ((val & DFI_INIT_COMPLETE) != DFI_INIT_COMPLETE);
+
+	clrbits_le32(&drex0->concontrol, DFI_INIT_START);
+	clrbits_le32(&drex1->concontrol, DFI_INIT_START);
+
+	update_reset_dll(drex0, DDR_MODE_DDR3);
+	update_reset_dll(drex1, DDR_MODE_DDR3);
+
+	/*
+	 * Set Base Address:
+	 * 0x2000_0000 ~ 0x5FFF_FFFF
+	 * 0x6000_0000 ~ 0x9FFF_FFFF
+	 */
+	/* MEMBASECONFIG0 */
+	val = DMC_MEMBASECONFIGX_CHIP_BASE(DMC_CHIP_BASE_0) |
+		DMC_MEMBASECONFIGX_CHIP_MASK(DMC_CHIP_MASK);
+	writel(val, &tzasc0->membaseconfig0);
+	writel(val, &tzasc1->membaseconfig0);
+
+	/* MEMBASECONFIG1 */
+	val = DMC_MEMBASECONFIGX_CHIP_BASE(DMC_CHIP_BASE_1) |
+		DMC_MEMBASECONFIGX_CHIP_MASK(DMC_CHIP_MASK);
+	writel(val, &tzasc0->membaseconfig1);
+	writel(val, &tzasc1->membaseconfig1);
+
+	/*
+	 * Memory Channel Inteleaving Size
+	 * Ares Channel interleaving = 128 bytes
+	 */
+	/* MEMCONFIG0/1 */
+	writel(mem->memconfig, &tzasc0->memconfig0);
+	writel(mem->memconfig, &tzasc1->memconfig0);
+	writel(mem->memconfig, &tzasc0->memconfig1);
+	writel(mem->memconfig, &tzasc1->memconfig1);
+
+	/* Precharge Configuration */
+	writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
+	       &drex0->prechconfig0);
+	writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
+	       &drex1->prechconfig0);
+
+	/*
+	 * TimingRow, TimingData, TimingPower and Timingaref
+	 * values as per Memory AC parameters
+	 */
+	writel(mem->timing_ref, &drex0->timingref);
+	writel(mem->timing_ref, &drex1->timingref);
+	writel(mem->timing_row, &drex0->timingrow);
+	writel(mem->timing_row, &drex1->timingrow);
+	writel(mem->timing_data, &drex0->timingdata);
+	writel(mem->timing_data, &drex1->timingdata);
+	writel(mem->timing_power, &drex0->timingpower);
+	writel(mem->timing_power, &drex1->timingpower);
+
+	if (reset) {
+		/*
+		 * Send NOP, MRS and ZQINIT commands
+		 * Sending MRS command will reset the DRAM. We should not be
+		 * reseting the DRAM after resume, this will lead to memory
+		 * corruption as DRAM content is lost after DRAM reset
+		 */
+		dmc_config_mrs(mem, drex0);
+		dmc_config_mrs(mem, drex1);
+	} else {
+		/*
+		 * During Suspend-Resume & S/W-Reset, as soon as PMU releases
+		 * pad retention, CKE goes high. This causes memory contents
+		 * not to be retained during DRAM initialization. Therfore,
+		 * there is a new control register(0x100431e8[28]) which lets us
+		 * release pad retention and retain the memory content until the
+		 * initialization is complete.
+		 */
+		writel(PAD_RETENTION_DRAM_COREBLK_VAL,
+		       PAD_RETENTION_DRAM_COREBLK_OPTION);
+		do {
+			val = readl(PAD_RETENTION_DRAM_STATUS);
+		} while (val != 0x1);
+
+		/*
+		 * CKE PAD retention disables DRAM self-refresh mode.
+		 * Send auto refresh command for DRAM refresh.
+		 */
+		for (i = 0; i < 128; i++) {
+			for (chip = 0; chip < mem->chips_to_configure; chip++) {
+				writel(DIRECT_CMD_REFA |
+				       (chip << DIRECT_CMD_CHIP_SHIFT),
+				       &drex0->directcmd);
+				writel(DIRECT_CMD_REFA |
+				       (chip << DIRECT_CMD_CHIP_SHIFT),
+				       &drex1->directcmd);
+			}
+		}
+	}
+
+	if (mem->gate_leveling_enable) {
+		writel(PHY_CON0_RESET_VAL, &phy0_ctrl->phy_con0);
+		writel(PHY_CON0_RESET_VAL, &phy1_ctrl->phy_con0);
+
+		setbits_le32(&phy0_ctrl->phy_con0, P0_CMD_EN);
+		setbits_le32(&phy1_ctrl->phy_con0, P0_CMD_EN);
+
+		val = PHY_CON2_RESET_VAL;
+		val |= INIT_DESKEW_EN;
+		writel(val, &phy0_ctrl->phy_con2);
+		writel(val, &phy1_ctrl->phy_con2);
+
+		val =  readl(&phy0_ctrl->phy_con1);
+		val |= (RDLVL_PASS_ADJ_VAL << RDLVL_PASS_ADJ_OFFSET);
+		writel(val, &phy0_ctrl->phy_con1);
+
+		val =  readl(&phy1_ctrl->phy_con1);
+		val |= (RDLVL_PASS_ADJ_VAL << RDLVL_PASS_ADJ_OFFSET);
+		writel(val, &phy1_ctrl->phy_con1);
+
+		n_lock_r = readl(&phy0_ctrl->phy_con13);
+		n_lock_w_phy0 = (n_lock_r & CTRL_LOCK_COARSE_MASK) >> 2;
+		n_lock_r = readl(&phy0_ctrl->phy_con12);
+		n_lock_r &= ~CTRL_DLL_ON;
+		n_lock_r |= n_lock_w_phy0;
+		writel(n_lock_r, &phy0_ctrl->phy_con12);
+
+		n_lock_r = readl(&phy1_ctrl->phy_con13);
+		n_lock_w_phy1 = (n_lock_r & CTRL_LOCK_COARSE_MASK) >> 2;
+		n_lock_r = readl(&phy1_ctrl->phy_con12);
+		n_lock_r &= ~CTRL_DLL_ON;
+		n_lock_r |= n_lock_w_phy1;
+		writel(n_lock_r, &phy1_ctrl->phy_con12);
+
+		val = (0x3 << DIRECT_CMD_BANK_SHIFT) | 0x4;
+		for (chip = 0; chip < mem->chips_to_configure; chip++) {
+			writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+			       &drex0->directcmd);
+			writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+			       &drex1->directcmd);
+		}
+
+		setbits_le32(&phy0_ctrl->phy_con2, RDLVL_GATE_EN);
+		setbits_le32(&phy1_ctrl->phy_con2, RDLVL_GATE_EN);
+
+		setbits_le32(&phy0_ctrl->phy_con0, CTRL_SHGATE);
+		setbits_le32(&phy1_ctrl->phy_con0, CTRL_SHGATE);
+
+		val = readl(&phy0_ctrl->phy_con1);
+		val &= ~(CTRL_GATEDURADJ_MASK);
+		writel(val, &phy0_ctrl->phy_con1);
+
+		val = readl(&phy1_ctrl->phy_con1);
+		val &= ~(CTRL_GATEDURADJ_MASK);
+		writel(val, &phy1_ctrl->phy_con1);
+
+		writel(CTRL_RDLVL_GATE_ENABLE, &drex0->rdlvl_config);
+		i = TIMEOUT;
+		while (((readl(&drex0->phystatus) & RDLVL_COMPLETE_CHO) !=
+			RDLVL_COMPLETE_CHO) && (i > 0)) {
+			/*
+			 * TODO(waihong): Comment on how long this take to
+			 * timeout
+			 */
+			sdelay(100);
+			i--;
+		}
+		if (!i)
+			return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+		writel(CTRL_RDLVL_GATE_DISABLE, &drex0->rdlvl_config);
+
+		writel(CTRL_RDLVL_GATE_ENABLE, &drex1->rdlvl_config);
+		i = TIMEOUT;
+		while (((readl(&drex1->phystatus) & RDLVL_COMPLETE_CHO) !=
+			RDLVL_COMPLETE_CHO) && (i > 0)) {
+			/*
+			 * TODO(waihong): Comment on how long this take to
+			 * timeout
+			 */
+			sdelay(100);
+			i--;
+		}
+		if (!i)
+			return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+		writel(CTRL_RDLVL_GATE_DISABLE, &drex1->rdlvl_config);
+
+		writel(0, &phy0_ctrl->phy_con14);
+		writel(0, &phy1_ctrl->phy_con14);
+
+		val = (0x3 << DIRECT_CMD_BANK_SHIFT);
+		for (chip = 0; chip < mem->chips_to_configure; chip++) {
+			writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+			       &drex0->directcmd);
+			writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+			       &drex1->directcmd);
+		}
+
+		if (mem->read_leveling_enable) {
+			/* Set Read DQ Calibration */
+			val = (0x3 << DIRECT_CMD_BANK_SHIFT) | 0x4;
+			for (chip = 0; chip < mem->chips_to_configure; chip++) {
+				writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+				       &drex0->directcmd);
+				writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+				       &drex1->directcmd);
+			}
+
+			val = readl(&phy0_ctrl->phy_con1);
+			val |= READ_LEVELLING_DDR3;
+			writel(val, &phy0_ctrl->phy_con1);
+			val = readl(&phy1_ctrl->phy_con1);
+			val |= READ_LEVELLING_DDR3;
+			writel(val, &phy1_ctrl->phy_con1);
+
+			val = readl(&phy0_ctrl->phy_con2);
+			val |= (RDLVL_EN | RDLVL_INCR_ADJ);
+			writel(val, &phy0_ctrl->phy_con2);
+			val = readl(&phy1_ctrl->phy_con2);
+			val |= (RDLVL_EN | RDLVL_INCR_ADJ);
+			writel(val, &phy1_ctrl->phy_con2);
+
+			setbits_le32(&drex0->rdlvl_config,
+				     CTRL_RDLVL_DATA_ENABLE);
+			i = TIMEOUT;
+			while (((readl(&drex0->phystatus) & RDLVL_COMPLETE_CHO)
+				 != RDLVL_COMPLETE_CHO) && (i > 0)) {
+				/*
+				 * TODO(waihong): Comment on how long this take
+				 * to timeout
+				 */
+				sdelay(100);
+				i--;
+			}
+			if (!i)
+				return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+
+			clrbits_le32(&drex0->rdlvl_config,
+				     CTRL_RDLVL_DATA_ENABLE);
+			setbits_le32(&drex1->rdlvl_config,
+				     CTRL_RDLVL_DATA_ENABLE);
+			i = TIMEOUT;
+			while (((readl(&drex1->phystatus) & RDLVL_COMPLETE_CHO)
+				 != RDLVL_COMPLETE_CHO) && (i > 0)) {
+				/*
+				 * TODO(waihong): Comment on how long this take
+				 * to timeout
+				 */
+				sdelay(100);
+				i--;
+			}
+			if (!i)
+				return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+
+			clrbits_le32(&drex1->rdlvl_config,
+				     CTRL_RDLVL_DATA_ENABLE);
+
+			val = (0x3 << DIRECT_CMD_BANK_SHIFT);
+			for (chip = 0; chip < mem->chips_to_configure; chip++) {
+				writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+				       &drex0->directcmd);
+				writel(val | (chip << DIRECT_CMD_CHIP_SHIFT),
+				       &drex1->directcmd);
+			}
+
+			update_reset_dll(drex0, DDR_MODE_DDR3);
+			update_reset_dll(drex1, DDR_MODE_DDR3);
+		}
+
+		/* Common Settings for Leveling */
+		val = PHY_CON12_RESET_VAL;
+		writel((val + n_lock_w_phy0), &phy0_ctrl->phy_con12);
+		writel((val + n_lock_w_phy1), &phy1_ctrl->phy_con12);
+
+		setbits_le32(&phy0_ctrl->phy_con2, DLL_DESKEW_EN);
+		setbits_le32(&phy1_ctrl->phy_con2, DLL_DESKEW_EN);
+	}
+
+	/* Send PALL command */
+	dmc_config_prech(mem, drex0);
+	dmc_config_prech(mem, drex1);
+
+	writel(mem->memcontrol, &drex0->memcontrol);
+	writel(mem->memcontrol, &drex1->memcontrol);
+
+	/*
+	 * Set DMC Concontrol: Enable auto-refresh counter, provide
+	 * read data fetch cycles and enable DREX auto set powerdown
+	 * for input buffer of I/O in none read memory state.
+	 */
+	writel(mem->concontrol | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT) |
+		(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)|
+		DMC_CONCONTROL_IO_PD_CON(0x2),
+		&drex0->concontrol);
+	writel(mem->concontrol | (mem->aref_en << CONCONTROL_AREF_EN_SHIFT) |
+		(mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)|
+		DMC_CONCONTROL_IO_PD_CON(0x2),
+		&drex1->concontrol);
+
+	/*
+	 * Enable Clock Gating Control for DMC
+	 * this saves around 25 mw dmc power as compared to the power
+	 * consumption without these bits enabled
+	 */
+	setbits_le32(&drex0->cgcontrol, DMC_INTERNAL_CG);
+	setbits_le32(&drex1->cgcontrol, DMC_INTERNAL_CG);
+
+	return 0;
+}
+#endif
arch/arm/include/asm/arch-exynos/cpu.h +0 -0
index a465e6d..c7f4a5e 100644

arch/arm/include/asm/arch-exynos/cpu.h line 166

Quoted 5 lines
arch/arm/include/asm/arch-exynos/cpu.h +2 -0
@@ -162,6 +162,10 @@
 #define EXYNOS5420_ADC_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS5420_MODEM_BASE		DEVICE_NOT_AVAILABLE
 
+#define PAD_RETENTION_DRAM_STATUS	(EXYNOS5420_POWER_BASE + 0x3004)
+#define PAD_RETENTION_DRAM_COREBLK_OPTION	(EXYNOS5420_POWER_BASE + 0x31E8)

NAK.
These are not a base address.
You should add this registers at structure of power.

arch/arm/include/asm/arch-exynos/cpu.h line 167

Quoted 1 line
arch/arm/include/asm/arch-exynos/cpu.h +1 -0
+#define PAD_RETENTION_DRAM_COREBLK_VAL	0x10000000

please move it to somewhere.

Quoted 194 lines
arch/arm/include/asm/arch-exynos/cpu.h +1 -0
+
 #ifndef __ASSEMBLY__
 #include <asm/io.h>
 /* CPU detection macros */
arch/arm/include/asm/arch-exynos/dmc.h +90 -32
index f65c676..0913299 100644
@@ -114,13 +114,24 @@ struct exynos4_dmc {
 struct exynos5_dmc {
 	unsigned int concontrol;
 	unsigned int memcontrol;
+
+/*
+ * Between 5250 and 5420, the DMC Register differs only at 0x8 offset.
+ * So to use the same structure and simplify the code put a define to
+ * distinguish between memconfig0 and cgcontrol register
+ */
+#ifdef CONFIG_EXYNOS5250
 	unsigned int memconfig0;
+#else
+	unsigned int cgcontrol;
+#endif
 	unsigned int memconfig1;
 	unsigned int directcmd;
-	unsigned int prechconfig;
+	unsigned int prechconfig0;
 	unsigned int phycontrol0;
-	unsigned char res1[0xc];
-	unsigned int pwrdnconfig;
+	unsigned int prechconfig1;
+	unsigned char res1[0x8];
+	unsigned int pwrdnconfig;	/* 0x0028*/
 	unsigned int timingpzq;
 	unsigned int timingref;
 	unsigned int timingrow;
@@ -128,12 +139,12 @@ struct exynos5_dmc {
 	unsigned int timingpower;
 	unsigned int phystatus;
 	unsigned char res2[0x4];
-	unsigned int chipstatus_ch0;
+	unsigned int chipstatus_ch0;	/* 0x0048 */
 	unsigned int chipstatus_ch1;
 	unsigned char res3[0x4];
 	unsigned int mrstatus;
 	unsigned char res4[0x8];
-	unsigned int qoscontrol0;
+	unsigned int qoscontrol0;	/* 0x0060 */
 	unsigned char resr5[0x4];
 	unsigned int qoscontrol1;
 	unsigned char res6[0x4];
@@ -164,45 +175,83 @@ struct exynos5_dmc {
 	unsigned int qoscontrol14;
 	unsigned char res19[0x4];
 	unsigned int qoscontrol15;
-	unsigned char res20[0x14];
+	unsigned char res20[0x4];
+	unsigned int timing_set_sw;	/* 0x00e0 */
+	unsigned int timingrow1;
+	unsigned int timingdata1;
+	unsigned int timingpower1;
 	unsigned int ivcontrol;
 	unsigned int wrtra_config;
 	unsigned int rdlvl_config;
-	unsigned char res21[0x8];
+	unsigned char res21[0x4];
+	unsigned int brbrsvcontrol;	/* 0x0100*/
 	unsigned int brbrsvconfig;
 	unsigned int brbqosconfig;
 	unsigned int membaseconfig0;
-	unsigned int membaseconfig1;
+	unsigned int membaseconfig1;	/* 0x0110 */
 	unsigned char res22[0xc];
-	unsigned int wrlvl_config;
-	unsigned char res23[0xc];
-	unsigned int perevcontrol;
+	unsigned int wrlvl_config0;	/* 0x0120 */
+	unsigned int wrlvl_config1;
+	unsigned int wrlvl_status;
+	unsigned char res23[0x4];
+	unsigned int perevcontrol;	/* 0x0130 */
 	unsigned int perev0config;
 	unsigned int perev1config;
 	unsigned int perev2config;
 	unsigned int perev3config;
-	unsigned char res24[0xdebc];
-	unsigned int pmnc_ppc_a;
-	unsigned char res25[0xc];
-	unsigned int cntens_ppc_a;
-	unsigned char res26[0xc];
-	unsigned int cntenc_ppc_a;
-	unsigned char res27[0xc];
-	unsigned int intens_ppc_a;
-	unsigned char res28[0xc];
-	unsigned int intenc_ppc_a;
-	unsigned char res29[0xc];
-	unsigned int flag_ppc_a;
-	unsigned char res30[0xac];
-	unsigned int ccnt_ppc_a;
-	unsigned char res31[0xc];
-	unsigned int pmcnt0_ppc_a;
+	unsigned char res22a[0xc];
+	unsigned int ctrl_io_rdata_ch0;
+	unsigned int ctrl_io_rdata_ch1;
+	unsigned char res23a[0x8];
+	unsigned int cacal_config0;
+	unsigned int cacal_config1;
+	unsigned int cacal_status;
+	unsigned char res24[0x94];
+	unsigned int emergent_config0;	/* 0x0200 */
+	unsigned int emergent_config1;
+	unsigned char res25[0x8];
+	unsigned int bp_control0;
+	unsigned int bp_control0_r;
+	unsigned int bp_control0_w;
+	unsigned char res26[0x4];
+	unsigned int bp_control1;
+	unsigned int bp_control1_r;
+	unsigned int bp_control1_w;
+	unsigned char res27[0x4];
+	unsigned int bp_control2;
+	unsigned int bp_control2_r;
+	unsigned int bp_control2_w;
+	unsigned char res28[0x4];
+	unsigned int bp_control3;
+	unsigned int bp_control3_r;
+	unsigned int bp_control3_w;
+	unsigned char res29[0xb4];
+	unsigned int winconfig_odt_w;	/* 0x0300 */
+	unsigned char res30[0x4];
+	unsigned int winconfig_ctrl_read;
+	unsigned int winconfig_ctrl_gate;
+	unsigned char res31[0xdcf0];
+	unsigned int pmnc_ppc;
 	unsigned char res32[0xc];
-	unsigned int pmcnt1_ppc_a;
+	unsigned int cntens_ppc;
 	unsigned char res33[0xc];
-	unsigned int pmcnt2_ppc_a;
+	unsigned int cntenc_ppc;
 	unsigned char res34[0xc];
-	unsigned int pmcnt3_ppc_a;
+	unsigned int intens_ppc;
+	unsigned char res35[0xc];
+	unsigned int intenc_ppc;
+	unsigned char res36[0xc];
+	unsigned int flag_ppc;		/* 0xe050 */
+	unsigned char res37[0xac];
+	unsigned int ccnt_ppc;
+	unsigned char res38[0xc];
+	unsigned int pmcnt0_ppc;
+	unsigned char res39[0xc];
+	unsigned int pmcnt1_ppc;
+	unsigned char res40[0xc];
+	unsigned int pmcnt2_ppc;
+	unsigned char res41[0xc];
+	unsigned int pmcnt3_ppc;	/* 0xe140 */
 };
 
 struct exynos5_phy_control {
@@ -211,13 +260,13 @@ struct exynos5_phy_control {
 	unsigned int phy_con2;
 	unsigned int phy_con3;
 	unsigned int phy_con4;
-	unsigned char res1[4];
+	unsigned int phy_con5;
 	unsigned int phy_con6;
 	unsigned char res2[4];
 	unsigned int phy_con8;
 	unsigned int phy_con9;
 	unsigned int phy_con10;
-	unsigned char res3[4];
+	unsigned int phy_con11;
 	unsigned int phy_con12;
 	unsigned int phy_con13;
 	unsigned int phy_con14;
@@ -252,6 +301,15 @@ struct exynos5_phy_control {
 	unsigned int phy_con42;
 };
 
+struct exynos5_tzasc {
+	unsigned char res1[0xf00];
+	unsigned int membaseconfig0;
+	unsigned int membaseconfig1;
+	unsigned char res2[0x8];
+	unsigned int memconfig0;
+	unsigned int memconfig1;
+};
+
 enum ddr_mode {
 	DDR_MODE_DDR2,
 	DDR_MODE_DDR3,

arch/arm/include/asm/arch-exynos/dmc.h enum mem_manuf { · line 350

Quoted 7 lines
arch/arm/include/asm/arch-exynos/dmc.h +1 -0
@@ -286,6 +344,7 @@ enum mem_manuf {
 #define PHY_CON0_T_WRRDCMD_SHIFT	17
 #define PHY_CON0_T_WRRDCMD_MASK		(0x7 << PHY_CON0_T_WRRDCMD_SHIFT)
 #define PHY_CON0_CTRL_DDR_MODE_SHIFT	11
+#define PHY_CON0_CTRL_DDR_MODE_MASK	0x3
 
 /* PHY_CON1 register fields */
 #define PHY_CON1_RDLVL_RDDATA_ADJ_SHIFT	0

Thanks,
Minkyu Kang.

#9 lore raw

PATCH v8 5/9 Exynos5420: Add support for 5420 in pinmux and gpio

In reply to Rajeshwari S Shinde

Adds code in pinmux and gpio framework to support Exynos5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added correct calculation of gpio based addresses.
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the coding style nits.
Chnages in V8:
- Corrected the coding style nits pointed by Minkyu Kang.

 arch/arm/cpu/armv7/exynos/pinmux.c        | 260 +++++++++++++++++++++++++++++-
 arch/arm/include/asm/arch-exynos/gpio.h   | 143 ++++++++++++++--
 arch/arm/include/asm/arch-exynos/periph.h |   3 +
 3 files changed, 390 insertions(+), 16 deletions(-)
arch/arm/cpu/armv7/exynos/pinmux.c +258 -2
index 8002bce..272ecb3 100644
@@ -46,6 +46,42 @@ static void exynos5_uart_config(int peripheral)
 	}
 }
 
+static void exynos5420_uart_config(int peripheral)
+{
+	struct exynos5420_gpio_part1 *gpio1 =
+		(struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
+	struct s5p_gpio_bank *bank;
+	int i, start, count;
+
+	switch (peripheral) {
+	case PERIPH_ID_UART0:
+		bank = &gpio1->a0;
+		start = 0;
+		count = 4;
+		break;
+	case PERIPH_ID_UART1:
+		bank = &gpio1->a0;
+		start = 4;
+		count = 4;
+		break;
+	case PERIPH_ID_UART2:
+		bank = &gpio1->a1;
+		start = 0;
+		count = 4;
+		break;
+	case PERIPH_ID_UART3:
+		bank = &gpio1->a1;
+		start = 4;
+		count = 2;
+		break;
+	}
+
+	for (i = start; i < start + count; i++) {
+		s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE);
+		s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+	}
+}
+
 static int exynos5_mmc_config(int peripheral, int flags)
 {
 	struct exynos5_gpio_part1 *gpio1 =
@@ -101,6 +137,75 @@ static int exynos5_mmc_config(int peripheral, int flags)
 	return 0;
 }
 
+static int exynos5420_mmc_config(int peripheral, int flags)
+{
+	struct exynos5420_gpio_part3 *gpio3 =
+		(struct exynos5420_gpio_part3 *)samsung_get_base_gpio_part3();
+	struct s5p_gpio_bank *bank = NULL, *bank_ext = NULL;
+	int i, start;
+
+	switch (peripheral) {
+	case PERIPH_ID_SDMMC0:
+		bank = &gpio3->c0;
+		bank_ext = &gpio3->c3;
+		start = 0;
+		break;
+	case PERIPH_ID_SDMMC1:
+		bank = &gpio3->c1;
+		bank_ext = &gpio3->d1;
+		start = 4;
+		break;
+	case PERIPH_ID_SDMMC2:
+		bank = &gpio3->c2;
+		bank_ext = NULL;
+		start = 0;
+		break;
+	default:
+		start = 0;
+		debug("%s: invalid peripheral %d", __func__, peripheral);
+		return -1;
+	}
+
+	if ((flags & PINMUX_FLAG_8BIT_MODE) && !bank_ext) {
+		debug("SDMMC device %d does not support 8bit mode",
+		      peripheral);
+		return -1;
+	}
+
+	if (flags & PINMUX_FLAG_8BIT_MODE) {
+		for (i = start; i <= (start + 3); i++) {
+			s5p_gpio_cfg_pin(bank_ext, i, GPIO_FUNC(0x2));
+			s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_UP);
+			s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X);
+		}
+	}
+
+	for (i = 0; i < 3; i++) {
+		/*
+		 * MMC0 is intended to be used for eMMC. The
+		 * card detect pin is used as a VDDEN signal to
+		 * power on the eMMC. The 5420 iROM makes
+		 * this same assumption.
+		 */
+		if ((peripheral == PERIPH_ID_SDMMC0) && (i == 2)) {
+			s5p_gpio_set_value(bank, i, 1);
+			s5p_gpio_cfg_pin(bank, i, GPIO_OUTPUT);
+		} else {
+			s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+		}
+		s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE);
+		s5p_gpio_set_drv(bank, i, GPIO_DRV_4X);
+	}
+
+	for (i = 3; i <= 6; i++) {
+		s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2));
+		s5p_gpio_set_pull(bank, i, GPIO_PULL_UP);
+		s5p_gpio_set_drv(bank, i, GPIO_DRV_4X);
+	}
+
+	return 0;
+}
+
 static void exynos5_sromc_config(int flags)
 {
 	struct exynos5_gpio_part1 *gpio1 =
@@ -216,6 +321,59 @@ static void exynos5_i2c_config(int peripheral, int flags)
 	}
 }
 
+static void exynos5420_i2c_config(int peripheral)
+{
+	struct exynos5420_gpio_part1 *gpio1 =
+		(struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
+
+	switch (peripheral) {
+	case PERIPH_ID_I2C0:
+		s5p_gpio_cfg_pin(&gpio1->b3, 0, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 1, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C1:
+		s5p_gpio_cfg_pin(&gpio1->b3, 2, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 3, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C2:
+		s5p_gpio_cfg_pin(&gpio1->a0, 6, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a0, 7, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C3:
+		s5p_gpio_cfg_pin(&gpio1->a1, 2, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a1, 3, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C4:
+		s5p_gpio_cfg_pin(&gpio1->a2, 0, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a2, 1, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C5:
+		s5p_gpio_cfg_pin(&gpio1->a2, 2, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->a2, 3, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C6:
+		s5p_gpio_cfg_pin(&gpio1->b1, 3, GPIO_FUNC(0x4));
+		s5p_gpio_cfg_pin(&gpio1->b1, 4, GPIO_FUNC(0x4));
+		break;
+	case PERIPH_ID_I2C7:
+		s5p_gpio_cfg_pin(&gpio1->b2, 2, GPIO_FUNC(0x3));
+		s5p_gpio_cfg_pin(&gpio1->b2, 3, GPIO_FUNC(0x3));
+		break;
+	case PERIPH_ID_I2C8:
+		s5p_gpio_cfg_pin(&gpio1->b3, 4, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 5, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C9:
+		s5p_gpio_cfg_pin(&gpio1->b3, 6, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b3, 7, GPIO_FUNC(0x2));
+		break;
+	case PERIPH_ID_I2C10:
+		s5p_gpio_cfg_pin(&gpio1->b4, 0, GPIO_FUNC(0x2));
+		s5p_gpio_cfg_pin(&gpio1->b4, 1, GPIO_FUNC(0x2));
+		break;
+	}
+}
+
 static void exynos5_i2s_config(int peripheral)
 {
 	int i;
@@ -279,6 +437,58 @@ void exynos5_spi_config(int peripheral)
 	}
 }
 
+void exynos5420_spi_config(int peripheral)
+{
+	int cfg, pin, i;
+	struct s5p_gpio_bank *bank = NULL;
+	struct exynos5420_gpio_part1 *gpio1 =
+		(struct exynos5420_gpio_part1 *)samsung_get_base_gpio_part1();
+	struct exynos5420_gpio_part4 *gpio4 =
+		(struct exynos5420_gpio_part4 *)samsung_get_base_gpio_part4();
+
+	switch (peripheral) {
+	case PERIPH_ID_SPI0:
+		bank = &gpio1->a2;
+		cfg = GPIO_FUNC(0x2);
+		pin = 0;
+		break;
+	case PERIPH_ID_SPI1:
+		bank = &gpio1->a2;
+		cfg = GPIO_FUNC(0x2);
+		pin = 4;
+		break;
+	case PERIPH_ID_SPI2:
+		bank = &gpio1->b1;
+		cfg = GPIO_FUNC(0x5);
+		pin = 1;
+		break;
+	case PERIPH_ID_SPI3:
+		bank = &gpio4->f1;
+		cfg = GPIO_FUNC(0x2);
+		pin = 0;
+		break;
+	case PERIPH_ID_SPI4:
+		cfg = 0;
+		pin = 0;
+		break;
+	default:
+		cfg = 0;
+		pin = 0;
+		debug("%s: invalid peripheral %d", __func__, peripheral);
+		return;
+	}
+
+	if (peripheral != PERIPH_ID_SPI4) {
+		for (i = pin; i < pin + 4; i++)
+			s5p_gpio_cfg_pin(bank, i, cfg);
+	} else {
+		for (i = 0; i < 2; i++) {
+			s5p_gpio_cfg_pin(&gpio4->f0, i + 2, GPIO_FUNC(0x4));
+			s5p_gpio_cfg_pin(&gpio4->e0, i + 4, GPIO_FUNC(0x4));
+		}
+	}
+}
+
 static int exynos5_pinmux_config(int peripheral, int flags)
 {
 	switch (peripheral) {
@@ -325,6 +535,48 @@ static int exynos5_pinmux_config(int peripheral, int flags)
 	return 0;
 }
 
+static int exynos5420_pinmux_config(int peripheral, int flags)
+{
+	switch (peripheral) {
+	case PERIPH_ID_UART0:
+	case PERIPH_ID_UART1:
+	case PERIPH_ID_UART2:
+	case PERIPH_ID_UART3:
+		exynos5420_uart_config(peripheral);
+		break;
+	case PERIPH_ID_SDMMC0:
+	case PERIPH_ID_SDMMC1:
+	case PERIPH_ID_SDMMC2:
+	case PERIPH_ID_SDMMC3:
+		return exynos5420_mmc_config(peripheral, flags);
+	case PERIPH_ID_SPI0:
+	case PERIPH_ID_SPI1:
+	case PERIPH_ID_SPI2:
+	case PERIPH_ID_SPI3:
+	case PERIPH_ID_SPI4:
+		exynos5420_spi_config(peripheral);
+		break;
+	case PERIPH_ID_I2C0:
+	case PERIPH_ID_I2C1:
+	case PERIPH_ID_I2C2:
+	case PERIPH_ID_I2C3:
+	case PERIPH_ID_I2C4:
+	case PERIPH_ID_I2C5:
+	case PERIPH_ID_I2C6:
+	case PERIPH_ID_I2C7:
+	case PERIPH_ID_I2C8:
+	case PERIPH_ID_I2C9:
+	case PERIPH_ID_I2C10:
+		exynos5420_i2c_config(peripheral);
+		break;
+	default:
+		debug("%s: invalid peripheral %d", __func__, peripheral);
+		return -1;
+	}
+
+	return 0;
+}
+
 static void exynos4_i2c_config(int peripheral, int flags)
 {
 	struct exynos4_gpio_part1 *gpio1 =
@@ -475,13 +727,17 @@ static int exynos4_pinmux_config(int peripheral, int flags)
 int exynos_pinmux_config(int peripheral, int flags)
 {
 	if (cpu_is_exynos5()) {
-		return exynos5_pinmux_config(peripheral, flags);
+		if (proid_is_exynos5420())
+			return exynos5420_pinmux_config(peripheral, flags);
+		else if (proid_is_exynos5250())
+			return exynos5_pinmux_config(peripheral, flags);
 	} else if (cpu_is_exynos4()) {
 		return exynos4_pinmux_config(peripheral, flags);
 	} else {
 		debug("pinmux functionality not supported\n");
-		return -1;
 	}
+
+	return -1;
 }
 
 #ifdef CONFIG_OF_CONTROL
arch/arm/include/asm/arch-exynos/gpio.h +129 -14

164 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/periph.h +3 -0
index 64bd8b7..30c7f18 100644
@@ -34,6 +34,9 @@ enum periph_id {
 	PERIPH_ID_SDMMC1,
 	PERIPH_ID_SDMMC2,
 	PERIPH_ID_SDMMC3,
+	PERIPH_ID_I2C8 = 87,
+	PERIPH_ID_I2C9,
+	PERIPH_ID_I2C10 = 203,
 	PERIPH_ID_I2S0 = 98,
 	PERIPH_ID_I2S1 = 99,
 
Signature · 1 line
1.7.12.4
#10 lore raw

PATCH v8 6/9 Exynos5420: Add base patch for SMDK5420

In reply to Rajeshwari S Shinde

Adding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Rebased on latest u-boot-samsung tree.
Changes in V5:
- Removed functions board_eth_init and board_mmc_init as they were moved to common/board.c
Changes in V6:
- None
Changes in V7:
- added CONFIG_EXYNOS_SPL to build 5420 and 5250
Changes in V8:
- None

 board/samsung/common/board.c          |   2 +
 board/samsung/smdk5420/Makefile       |  34 ++++++++
 board/samsung/smdk5420/smdk5420.c     | 159 ++++++++++++++++++++++++++++++++++
 board/samsung/smdk5420/smdk5420_spl.c |  52 +++++++++++
 boards.cfg                            |   1 +
 include/configs/arndale.h             |   1 +
 include/configs/exynos5250-dt.h       |   1 +
 tools/Makefile                        |   3 +-
 8 files changed, 252 insertions(+), 1 deletion(-)
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
board/samsung/common/board.c +2 -0
index 9ebfc42..2512a59 100644
@@ -143,6 +143,7 @@ struct cros_ec_dev *board_get_cros_ec_dev(void)
 	return local.cros_ec_dev;
 }
 
+#ifdef CONFIG_CROS_EC
 static int board_init_cros_ec_devices(const void *blob)
 {
 	local.cros_ec_err = cros_ec_init(blob, &local.cros_ec_dev);
@@ -151,6 +152,7 @@ static int board_init_cros_ec_devices(const void *blob)
 
 	return 0;
 }
+#endif
 
 #if defined(CONFIG_POWER)
 #ifdef CONFIG_POWER_MAX77686
board/samsung/smdk5420/Makefile new file +34 -0
new file mode 100644
index 0000000..be538ec
@@ -0,0 +1,34 @@
+#
+# Copyright (C) 2013 Samsung Electronics
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	+= smdk5420_spl.o
+
+ifndef CONFIG_SPL_BUILD
+COBJS	+= smdk5420.o
+endif
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+ALL	:=	 $(obj).depend $(LIB)
+
+all:	$(ALL)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/samsung/smdk5420/smdk5420.c new file +159 -0

159 lines not on this page · raw message

board/samsung/smdk5420/smdk5420_spl.c new file +52 -0

52 lines not on this page · raw message

boards.cfg +1 -0
index 3a56eab..06849e4 100644
@@ -272,6 +272,7 @@ Active  arm         armv7          exynos      samsung         arndale
 Active  arm         armv7          exynos      samsung         origen              origen                               -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         smdk5250            smdk5250                             -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         smdk5250            snow                                 -                                                                                                                                 Rajeshwari Shinde <[email protected]>
+Active  arm         armv7          exynos      samsung         smdk5420            smdk5420                                 -                                                                                                                                 Rajeshwari Shinde <[email protected]>
 Active  arm         armv7          exynos      samsung         smdkv310            smdkv310                             -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         trats               trats                                -                                                                                                                                 Lukasz Majewski <[email protected]>
 Active  arm         armv7          exynos      samsung         trats2              trats2                               -                                                                                                                                 Piotr Wilczek <[email protected]>
include/configs/arndale.h +1 -0
index ed44a04..743d30d 100644
@@ -117,6 +117,7 @@
 #define CONFIG_USB_STORAGE
 
 /* MMC SPL */
+#define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
include/configs/exynos5250-dt.h +1 -0
index 3736ea8..1ed36dd 100644
@@ -152,6 +152,7 @@
 #define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
 
 /* MMC SPL */
+#define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
tools/Makefile +2 -1
index ca76f94..05467e2 100644
@@ -53,6 +53,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
 BIN_FILES-y += mkenvimage$(SFX)
 BIN_FILES-y += mkimage$(SFX)
 BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX)
+BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX)
 BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
@@ -87,7 +88,7 @@ NOPED_OBJ_FILES-y += ublimage.o
 OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o
 OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o
 OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o
-OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o
+OBJ_FILES-$(CONFIG_EXYNOS_SPL) += mkexynosspl.o
 OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o
 OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o
 OBJ_FILES-$(CONFIG_MX23) += mxsboot.o
Signature · 1 line
1.7.12.4

A message that is not in the archive (sent off-list or not yet received): [email protected]

#12 lore raw

PATCH v8 6/9 Exynos5420: Add base patch for SMDK5420

ping.

-------- Original Message --------
Subject: Re: [PATCH 6/9 v8] Exynos5420: Add base patch for SMDK5420
Date: Thu, 21 Nov 2013 16:24:14 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com

Dear Rajeshwari,

Quoted 226 lines · Rajeshwari S Shinde

Adding the base patch for Exynos based SMDK5420. This shall enable compilation and basic boot support for SMDK5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Rebased on latest u-boot-samsung tree.
Changes in V5:
- Removed functions board_eth_init and board_mmc_init as they were moved to common/board.c
Changes in V6:
- None
Changes in V7:
- added CONFIG_EXYNOS_SPL to build 5420 and 5250
Changes in V8:
- None

 board/samsung/common/board.c          |   2 +
 board/samsung/smdk5420/Makefile       |  34 ++++++++
 board/samsung/smdk5420/smdk5420.c     | 159 ++++++++++++++++++++++++++++++++++
 board/samsung/smdk5420/smdk5420_spl.c |  52 +++++++++++
 boards.cfg                            |   1 +
 include/configs/arndale.h             |   1 +
 include/configs/exynos5250-dt.h       |   1 +
 tools/Makefile                        |   3 +-
 8 files changed, 252 insertions(+), 1 deletion(-)
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
board/samsung/common/board.c +2 -0
index 9ebfc42..2512a59 100644
@@ -143,6 +143,7 @@ struct cros_ec_dev *board_get_cros_ec_dev(void)
 	return local.cros_ec_dev;
 }
 
+#ifdef CONFIG_CROS_EC
 static int board_init_cros_ec_devices(const void *blob)
 {
 	local.cros_ec_err = cros_ec_init(blob, &local.cros_ec_dev);
@@ -151,6 +152,7 @@ static int board_init_cros_ec_devices(const void *blob)
 
 	return 0;
 }
+#endif
 
 #if defined(CONFIG_POWER)
 #ifdef CONFIG_POWER_MAX77686
board/samsung/smdk5420/Makefile new file +34 -0
new file mode 100644
index 0000000..be538ec
@@ -0,0 +1,34 @@
+#
+# Copyright (C) 2013 Samsung Electronics
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS	+= smdk5420_spl.o
+
+ifndef CONFIG_SPL_BUILD
+COBJS	+= smdk5420.o
+endif
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+
+ALL	:=	 $(obj).depend $(LIB)
+
+all:	$(ALL)
+
+$(LIB):	$(OBJS)
+	$(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/samsung/smdk5420/smdk5420.c new file +125 -0
new file mode 100644
index 0000000..d85b953
@@ -0,0 +1,159 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <fdtdec.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include <lcd.h>
+#include <spi.h>
+#include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/pinmux.h>
+#include <asm/arch/dp_info.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_USB_EHCI_EXYNOS
+static int board_usb_vbus_init(void)
+{
+	struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *)
+						samsung_get_base_gpio_part1();
+
+	/* Enable VBUS power switch */
+	s5p_gpio_direction_output(&gpio1->x2, 6, 1);
+
+	/* VBUS turn ON time */
+	mdelay(3);
+
+	return 0;
+}
+#endif
+
+int exynos_init(void)
+{
+#ifdef CONFIG_USB_EHCI_EXYNOS
+	board_usb_vbus_init();
+#endif
+	return 0;
+}
+
+#ifdef CONFIG_LCD
+void cfg_lcd_gpio(void)
+{
+	struct exynos5_gpio_part1 *gpio1 =
+		(struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1();
+
+	/* For Backlight */
+	s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT);
+	s5p_gpio_set_value(&gpio1->b2, 0, 1);
+
+	/* LCD power on */
+	s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT);
+	s5p_gpio_set_value(&gpio1->x1, 5, 1);
+
+	/* Set Hotplug detect for DP */
+	s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3));
+}
+
+vidinfo_t panel_info = {
+	.vl_freq	= 60,
+	.vl_col		= 2560,
+	.vl_row		= 1600,
+	.vl_width	= 2560,
+	.vl_height	= 1600,
+	.vl_clkp	= CONFIG_SYS_LOW,
+	.vl_hsp		= CONFIG_SYS_LOW,
+	.vl_vsp		= CONFIG_SYS_LOW,
+	.vl_dp		= CONFIG_SYS_LOW,
+	.vl_bpix	= 4,	/* LCD_BPP = 2^4, for output conosle on LCD */
+
+	/* wDP panel timing infomation */
+	.vl_hspw	= 32,
+	.vl_hbpd	= 80,
+	.vl_hfpd	= 48,
+
+	.vl_vspw	= 6,
+	.vl_vbpd	= 37,
+	.vl_vfpd	= 3,
+	.vl_cmd_allow_len = 0xf,
+
+	.win_id		= 3,
+	.cfg_gpio	= cfg_lcd_gpio,
+	.backlight_on	= NULL,
+	.lcd_power_on	= NULL,
+	.reset_lcd	= NULL,
+	.dual_lcd_enabled = 0,
+
+	.init_delay	= 0,
+	.power_on_delay = 0,
+	.reset_delay	= 0,
+	.interface_mode = FIMD_RGB_INTERFACE,
+	.dp_enabled	= 1,
+};
+
+static struct edp_device_info edp_info = {
+	.disp_info = {
+		.h_res = 2560,
+		.h_sync_width = 32,
+		.h_back_porch = 80,
+		.h_front_porch = 48,
+		.v_res = 1600,
+		.v_sync_width  = 6,
+		.v_back_porch = 37,
+		.v_front_porch = 3,
+		.v_sync_rate = 60,
+	},
+	.lt_info = {
+		.lt_status = DP_LT_NONE,
+	},
+	.video_info = {
+		.master_mode = 0,
+		.bist_mode = DP_DISABLE,
+		.bist_pattern = NO_PATTERN,
+		.h_sync_polarity = 0,
+		.v_sync_polarity = 0,
+		.interlaced = 0,
+		.color_space = COLOR_RGB,
+		.dynamic_range = VESA,
+		.ycbcr_coeff = COLOR_YCBCR601,
+		.color_depth = COLOR_8,
+	},

board/samsung/smdk5420/smdk5420.c line 135

Quoted 10 lines
board/samsung/smdk5420/smdk5420.c new file +10 -0
+};
+
+static struct exynos_dp_platform_data dp_platform_data = {
+	.phy_enable	= set_dp_phy_ctrl,
+	.edp_dev_info	= &edp_info,
+};
+
+void init_panel_info(vidinfo_t *vid)
+{
+	vid->rgb_mode   = MODE_RGB_P,

typo?
Did you try to build your patch?

Quoted 132 lines
board/samsung/smdk5420/smdk5420.c new file +24 -0
+
+	exynos_set_dp_platform_data(&dp_platform_data);
+}
+#endif
+
+int board_get_revision(void)
+{
+	return 0;
+}
+
+#ifdef CONFIG_DISPLAY_BOARDINFO
+int checkboard(void)
+{
+	const char *board_name;
+
+	board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL);
+	if (board_name == NULL)
+		printf("\nUnknown Board\n");
+	else
+		printf("\nBoard: %s\n", board_name);
+
+	return 0;
+}
+#endif
board/samsung/smdk5420/smdk5420_spl.c new file +52 -0
new file mode 100644
index 0000000..73359f7
@@ -0,0 +1,52 @@
+/*
+ * Copyright (C) 2013 The Chromium OS Authors.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/spl.h>
+#include <asm/arch/clk.h>
+
+#define SIGNATURE	0xdeadbeef
+
+/* Parameters of early board initialization in SPL */
+static struct spl_machine_param machine_param
+		__attribute__((section(".machine_param"))) = {
+	.signature	= SIGNATURE,
+	.version	= 1,
+	.params		= "vmubfasirM",
+	.size		= sizeof(machine_param),
+
+	.mem_iv_size	= 0x1f,
+	.mem_type	= DDR_MODE_DDR3,
+
+	/*
+	 * Set uboot_size to 0x100000 bytes.
+	 *
+	 * This is an overly conservative value chosen to accommodate all
+	 * possible U-Boot image.  You are advised to set this value to a
+	 * smaller realistic size via scripts that modifies the .machine_param
+	 * section of output U-Boot image.
+	 */
+	.uboot_size	= 0x100000,
+
+	.boot_source	= BOOT_MODE_OM,
+	.frequency_mhz	= 800,
+	.arm_freq_mhz	= 900,
+	.serial_base	= 0x12c30000,
+	.i2c_base	= 0x12c60000,
+	.mem_manuf	= MEM_MANUF_SAMSUNG,
+};
+
+struct spl_machine_param *spl_get_machine_params(void)
+{
+	if (machine_param.signature != SIGNATURE) {
+		/* Will hang if SIGNATURE dont match */
+		while (1)
+			;
+	}
+
+	return &machine_param;
+}
boards.cfg +1 -0
index 3a56eab..06849e4 100644
@@ -272,6 +272,7 @@ Active  arm         armv7          exynos      samsung         arndale
 Active  arm         armv7          exynos      samsung         origen              origen                               -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         smdk5250            smdk5250                             -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         smdk5250            snow                                 -                                                                                                                                 Rajeshwari Shinde <[email protected]>
+Active  arm         armv7          exynos      samsung         smdk5420            smdk5420                                 -                                                                                                                                 Rajeshwari Shinde <[email protected]>
 Active  arm         armv7          exynos      samsung         smdkv310            smdkv310                             -                                                                                                                                 Chander Kashyap <[email protected]>
 Active  arm         armv7          exynos      samsung         trats               trats                                -                                                                                                                                 Lukasz Majewski <[email protected]>
 Active  arm         armv7          exynos      samsung         trats2              trats2                               -                                                                                                                                 Piotr Wilczek <[email protected]>
include/configs/arndale.h +1 -0
index ed44a04..743d30d 100644
@@ -117,6 +117,7 @@
 #define CONFIG_USB_STORAGE
 
 /* MMC SPL */
+#define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
include/configs/exynos5250-dt.h +1 -0
index 3736ea8..1ed36dd 100644
@@ -152,6 +152,7 @@
 #define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
 
 /* MMC SPL */
+#define CONFIG_EXYNOS_SPL
 #define CONFIG_SPL
 #define COPY_BL2_FNPTR_ADDR	0x02020030
 
tools/Makefile +1 -0
index ca76f94..05467e2 100644
@@ -53,6 +53,7 @@ BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
 BIN_FILES-y += mkenvimage$(SFX)
 BIN_FILES-y += mkimage$(SFX)
 BIN_FILES-$(CONFIG_EXYNOS5250) += mk$(BOARD)spl$(SFX)
+BIN_FILES-$(CONFIG_EXYNOS5420) += mk$(BOARD)spl$(SFX)
 BIN_FILES-$(CONFIG_MX23) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)

tools/Makefile NOPED_OBJ_FILES-y += ublimage.o · line 94

Quoted 8 lines
tools/Makefile +1 -1
@@ -87,7 +88,7 @@ NOPED_OBJ_FILES-y += ublimage.o
 OBJ_FILES-$(CONFIG_BUILD_ENVCRC) += envcrc.o
 OBJ_FILES-$(CONFIG_CMD_LOADS) += img2srec.o
 OBJ_FILES-$(CONFIG_CMD_NET) += gen_eth_addr.o
-OBJ_FILES-$(CONFIG_EXYNOS5250) += mkexynosspl.o
+OBJ_FILES-$(CONFIG_EXYNOS_SPL) += mkexynosspl.o
 OBJ_FILES-$(CONFIG_KIRKWOOD) += kwboot.o
 OBJ_FILES-$(CONFIG_LCD_LOGO) += bmp_logo.o
 OBJ_FILES-$(CONFIG_MX23) += mxsboot.o

Thanks,
Minkyu Kang.

#13 lore raw

PATCH v8 7/9 DTS: Add dts support for SMDK5420

In reply to Rajeshwari S Shinde

This patch adds dts support for SMDK5420.
exynos5.dtsi created is a common file which has the nodes common to both 5420 and 5250.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Added /include/ "exynos5420.dtsi
Changes in V5:
- None
Changes in V6:
- None
Changes in V7:
- Corrected the license.
Changes in V8:
- None

 arch/arm/dts/exynos5.dtsi                 | 198 ++++++++++++++++++++++++++++++
 arch/arm/dts/exynos5250.dtsi              | 196 +----------------------------
 arch/arm/dts/exynos5420.dtsi              |  70 +++++++++++
 board/samsung/dts/exynos5420-smdk5420.dts | 169 +++++++++++++++++++++++++
 4 files changed, 441 insertions(+), 192 deletions(-)
 create mode 100644 arch/arm/dts/exynos5.dtsi
 create mode 100644 arch/arm/dts/exynos5420.dtsi
 create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
arch/arm/dts/exynos5.dtsi new file +198 -0
new file mode 100644
index 0000000..f8c8741
@@ -0,0 +1,198 @@
+/*
+ * Copyright (c) 2013 The Chromium OS Authors
+ * SAMSUNG EXYNOS5 SoC device tree source
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "samsung,exynos5";
+
+	sromc at 12250000 {
+		compatible = "samsung,exynos-sromc";
+		reg = <0x12250000 0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c at 12c60000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C60000 0x100>;
+		interrupts = <0 56 0>;
+	};
+
+	i2c at 12c70000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C70000 0x100>;
+		interrupts = <0 57 0>;
+	};
+
+	i2c at 12c80000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C80000 0x100>;
+		interrupts = <0 58 0>;
+	};
+
+	i2c at 12c90000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x12C90000 0x100>;
+		interrupts = <0 59 0>;
+	};
+
+	spi at 12d20000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x12d20000 0x30>;
+		interrupts = <0 68 0>;
+	};
+
+	spi at 12d30000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x12d30000 0x30>;
+		interrupts = <0 69 0>;
+	};
+
+	spi at 12d40000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x12d40000 0x30>;
+		clock-frequency = <50000000>;
+		interrupts = <0 70 0>;
+        };
+
+	spi at 131a0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x131a0000 0x30>;
+		interrupts = <0 129 0>;
+	};
+
+	spi at 131b0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos-spi";
+		reg = <0x131b0000 0x30>;
+		interrupts = <0 130 0>;
+	};
+
+	ehci at 12110000 {
+		compatible = "samsung,exynos-ehci";
+		reg = <0x12110000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		phy {
+			compatible = "samsung,exynos-usb-phy";
+			reg = <0x12130000 0x100>;
+		};
+	};
+
+	tmu at 10060000 {
+		compatible = "samsung,exynos-tmu";
+		reg = <0x10060000 0x10000>;
+	};
+
+	fimd at 14400000 {
+		compatible = "samsung,exynos-fimd";
+		reg = <0x14400000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	dp at 145b0000 {
+		compatible = "samsung,exynos5-dp";
+		reg = <0x145b0000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	xhci0: xhci at 12000000 {
+		compatible = "samsung,exynos5250-xhci";
+		reg = <0x12000000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		phy {
+			compatible = "samsung,exynos5250-usb3-phy";
+			reg = <0x12100000 0x100>;
+		};
+	};
+
+	mmc at 12200000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12200000 0x1000>;
+		interrupts = <0 75 0>;
+	};
+
+	mmc at 12210000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12210000 0x1000>;
+		interrupts = <0 76 0>;
+	};
+
+	mmc at 12220000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12220000 0x1000>;
+		interrupts = <0 77 0>;
+	};
+
+	mmc at 12230000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,exynos5250-dwmmc";
+		reg = <0x12230000 0x1000>;
+		interrupts = <0 78 0>;
+	};
+
+	serial at 12C00000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C00000 0x100>;
+		interrupts = <0 51 0>;
+		id = <0>;
+	};
+
+	serial at 12C10000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C10000 0x100>;
+		interrupts = <0 52 0>;
+		id = <1>;
+	};
+
+	serial at 12C20000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C20000 0x100>;
+		interrupts = <0 53 0>;
+		id = <2>;
+	};
+
+	serial at 12C30000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x12C30000 0x100>;
+		interrupts = <0 54 0>;
+		id = <3>;
+	};
+
+	gpio: gpio {
+	};
+};
arch/arm/dts/exynos5250.dtsi +4 -192

209 lines not on this page · raw message

arch/arm/dts/exynos5420.dtsi new file +70 -0

70 lines not on this page · raw message

board/samsung/dts/exynos5420-smdk5420.dts new file +169 -0

169 lines not on this page · raw message

Signature · 1 line
1.7.12.4
#14 lore raw

PATCH v8 8/9 Config: Add initial config for SMDK5420

In reply to Rajeshwari S Shinde

Adding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None
Chnages in V7:
- Corrected the coding style nits.
Changes in V8:
- None

 include/configs/exynos5-dt.h    | 300 +++++++++++++++++++++++++++++++++++++
 include/configs/exynos5250-dt.h | 319 +---------------------------------------
 include/configs/smdk5420.h      |  49 ++++++
 3 files changed, 357 insertions(+), 311 deletions(-)
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h
include/configs/exynos5-dt.h new file +300 -0
new file mode 100644
index 0000000..2b3714f
@@ -0,0 +1,300 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG EXYNOS5 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_SAMSUNG			/* in a SAMSUNG core */
+#define CONFIG_S5P			/* S5P Family */
+#define CONFIG_EXYNOS5			/* which is in a Exynos5 Family */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_COMMON
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_EXYNOS_SPL
+
+/* Enable fdt support for Exynos5250 */
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* Allow tracing to be enabled */
+#define CONFIG_TRACE
+#define CONFIG_CMD_TRACE
+#define CONFIG_TRACE_BUFFER_SIZE	(16 << 20)
+#define CONFIG_TRACE_EARLY_SIZE		(8 << 20)
+#define CONFIG_TRACE_EARLY
+#define CONFIG_TRACE_EARLY_ADDR		0x50000000
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_SYS_DCACHE_OFF
+
+/* Enable ACE acceleration for SHA1 and SHA256 */
+#define CONFIG_EXYNOS_ACE_SHA
+#define CONFIG_SHA_HW_ACCEL
+
+/* input clock of PLL: SMDK5250 has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ		24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP			0x00000BAD
+#define S5P_CHECK_DIDLE			0xBAD00000
+#define S5P_CHECK_LPA			0xABAD0000
+
+/* Offset for inform registers */
+#define INFORM0_OFFSET			0x800
+#define INFORM1_OFFSET			0x804
+#define INFORM2_OFFSET			0x808
+#define INFORM3_OFFSET			0x80c
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (4 << 20))
+
+/* select serial console configuration */
+#define CONFIG_BAUDRATE			115200
+#define EXYNOS5_DEFAULT_UART_OFFSET	0x010000
+#define CONFIG_SILENT_CONSOLE
+
+/* Enable keyboard */
+#define CONFIG_CROS_EC		/* CROS_EC protocol */
+#define CONFIG_CROS_EC_SPI		/* Support CROS_EC over SPI */
+#define CONFIG_CROS_EC_I2C		/* Support CROS_EC over I2C */
+#define CONFIG_CROS_EC_KEYB	/* CROS_EC keyboard input */
+#define CONFIG_CMD_CROS_EC
+#define CONFIG_KEYBOARD
+
+/* Console configuration */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define EXYNOS_DEVICE_SETTINGS \
+		"stdin=serial,cros-ec-keyb\0" \
+		"stdout=serial,lcd\0" \
+		"stderr=serial,lcd\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	EXYNOS_DEVICE_SETTINGS
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_SDHCI
+#define CONFIG_S5P_SDHCI
+#define CONFIG_DWMMC
+#define CONFIG_EXYNOS_DWMMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/* PWM */
+#define CONFIG_PWM
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_HASH
+
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+/* Thermal Management Unit */
+#define CONFIG_EXYNOS_TMU
+#define CONFIG_CMD_DTT
+#define CONFIG_TMU_CMD_DTT
+
+/* USB */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_EXYNOS
+#define CONFIG_USB_STORAGE
+
+/* USB boot mode */
+#define CONFIG_USB_BOOTING
+#define EXYNOS_COPY_USB_FNPTR_ADDR	0x02020070
+#define EXYNOS_USB_SECONDARY_BOOT	0xfeed0002
+#define EXYNOS_IRAM_SECONDARY_BASE	0x02020018
+
+/* TPM */
+#define CONFIG_TPM
+#define CONFIG_CMD_TPM
+#define CONFIG_TPM_TIS_I2C
+#define CONFIG_TPM_TIS_I2C_BUS_NUMBER	3
+#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
+
+/* MMC SPL */
+#define CONFIG_SPL
+#define COPY_BL2_FNPTR_ADDR	0x02020030
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+
+/* specific .lds file */
+#define CONFIG_SPL_LDSCRIPT	"board/samsung/common/exynos-uboot-spl.lds"
+#define CONFIG_SPL_MAX_FOOTPRINT	(14 * 1024)
+
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5E00000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_RD_LVL
+
+#define CONFIG_NR_DRAM_BANKS	8
+#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_5		(CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_5_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_6		(CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_6_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_7		(CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_7_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_8		(CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_8_SIZE	SDRAM_BANK_SIZE
+
+#define CONFIG_SYS_MONITOR_BASE	0x00000000
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_SYS_MMC_ENV_DEV		0
+
+#define CONFIG_SECURE_BL1_ONLY
+
+/* Secure FW size configuration */
+#ifdef	CONFIG_SECURE_BL1_ONLY
+#define	CONFIG_SEC_FW_SIZE	(8 << 10) /* 8KB */
+#else
+#define	CONFIG_SEC_FW_SIZE	0
+#endif
+
+/* Configuration of BL1, BL2, ENV Blocks on mmc */
+#define CONFIG_RES_BLOCK_SIZE	(512)
+#define CONFIG_BL1_SIZE	(16 << 10) /*16 K reserved for BL1*/
+#define	CONFIG_BL2_SIZE	(512UL << 10UL)	/* 512 KB */
+#define CONFIG_ENV_SIZE	(16 << 10)	/* 16 KB */
+
+#define CONFIG_BL1_OFFSET	(CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
+#define CONFIG_BL2_OFFSET	(CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
+#define CONFIG_ENV_OFFSET	(CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
+
+/* U-boot copy size from boot Media to DRAM.*/
+#define BL2_START_OFFSET	(CONFIG_BL2_OFFSET/512)
+#define BL2_SIZE_BLOC_COUNT	(CONFIG_BL2_SIZE/512)
+
+#define CONFIG_SPI_BOOTING
+#define EXYNOS_COPY_SPI_FNPTR_ADDR	0x02020058
+#define SPI_FLASH_UBOOT_POS		(CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_PART
+#define CONFIG_PARTITION_UUIDS
+
+/* I2C */
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_HARD_I2C
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_SPEED	100000		/* 100 Kbps */
+#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SLAVE    0x0
+#define CONFIG_I2C_EDID
+
+/* SPI */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SPI_FLASH
+
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_EXYNOS_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SPI_FLASH_GIGADEVICE
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED		50000000
+#define EXYNOS5_SPI_NUM_CONTROLLERS	5
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_MODE	SPI_MODE_0
+#define CONFIG_ENV_SECT_SIZE	CONFIG_ENV_SIZE
+#define CONFIG_ENV_SPI_BUS	1
+#define CONFIG_ENV_SPI_MAX_HZ	50000000
+#endif
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+
+/* Ethernet Controllor Driver */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_BASE		0x5000000
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_ENV_SROM_BANK		1
+#endif /*CONFIG_CMD_NET*/
+
+/* Enable PXE Support */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PXE
+#define CONFIG_MENU
+#endif
+
+/* Enable devicetree support */
+#define CONFIG_OF_LIBFDT
+
+/* SHA hashing */
+#define CONFIG_CMD_HASH
+#define CONFIG_HASH_VERIFY
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+
+/* Enable Time Command */
+#define CONFIG_CMD_TIME
+
+#define CONFIG_CMD_BOOTZ
+
+#endif	/* __CONFIG_H */
include/configs/exynos5250-dt.h +8 -311

360 lines not on this page · raw message

include/configs/smdk5420.h new file +49 -0

49 lines not on this page · raw message

Signature · 1 line
1.7.12.4

A message that is not in the archive (sent off-list or not yet received): [email protected]

#16 lore raw

PATCH v8 8/9 Config: Add initial config for SMDK5420

ping.

-------- Original Message --------
Subject: Re: [PATCH 8/9 v8] Config: Add initial config for SMDK5420
Date: Thu, 21 Nov 2013 16:32:32 +0900
From: Minkyu Kang <[email protected]>
Organization: SAMSUNG ELECTRONICS
To: Rajeshwari S Shinde <[email protected]>
CC: u-boot at lists.denx.de, patches at linaro.org, sjg at chromium.org, chander.kashyap at linaro.org, u-boot-review at google.com, alim.akhtar at samsung.com, trini at ti.com

Dear Rajeshwari,

Quoted 232 lines · Rajeshwari S Shinde

Adding initial config for SMDK5420 to build and boot U-Boot over Exynos based SMDK5420.

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None
Chnages in V7:
- Corrected the coding style nits.
Changes in V8:
- None

 include/configs/exynos5-dt.h    | 300 +++++++++++++++++++++++++++++++++++++
 include/configs/exynos5250-dt.h | 319 +---------------------------------------
 include/configs/smdk5420.h      |  49 ++++++
 3 files changed, 357 insertions(+), 311 deletions(-)
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h
include/configs/exynos5-dt.h new file +198 -0
new file mode 100644
index 0000000..2b3714f
@@ -0,0 +1,300 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG EXYNOS5 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_SAMSUNG			/* in a SAMSUNG core */
+#define CONFIG_S5P			/* S5P Family */
+#define CONFIG_EXYNOS5			/* which is in a Exynos5 Family */
+
+#include <asm/arch/cpu.h>		/* get chip and board defs */
+
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOARD_COMMON
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_EXYNOS_SPL
+
+/* Enable fdt support for Exynos5250 */
+#define CONFIG_OF_CONTROL
+#define CONFIG_OF_SEPARATE
+
+/* Allow tracing to be enabled */
+#define CONFIG_TRACE
+#define CONFIG_CMD_TRACE
+#define CONFIG_TRACE_BUFFER_SIZE	(16 << 20)
+#define CONFIG_TRACE_EARLY_SIZE		(8 << 20)
+#define CONFIG_TRACE_EARLY
+#define CONFIG_TRACE_EARLY_ADDR		0x50000000
+
+/* Keep L2 Cache Disabled */
+#define CONFIG_SYS_DCACHE_OFF
+
+/* Enable ACE acceleration for SHA1 and SHA256 */
+#define CONFIG_EXYNOS_ACE_SHA
+#define CONFIG_SHA_HW_ACCEL
+
+/* input clock of PLL: SMDK5250 has 24MHz input clock */
+#define CONFIG_SYS_CLK_FREQ		24000000
+
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_CMDLINE_EDITING
+
+/* Power Down Modes */
+#define S5P_CHECK_SLEEP			0x00000BAD
+#define S5P_CHECK_DIDLE			0xBAD00000
+#define S5P_CHECK_LPA			0xABAD0000
+
+/* Offset for inform registers */
+#define INFORM0_OFFSET			0x800
+#define INFORM1_OFFSET			0x804
+#define INFORM2_OFFSET			0x808
+#define INFORM3_OFFSET			0x80c
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (4 << 20))
+
+/* select serial console configuration */
+#define CONFIG_BAUDRATE			115200
+#define EXYNOS5_DEFAULT_UART_OFFSET	0x010000
+#define CONFIG_SILENT_CONSOLE
+
+/* Enable keyboard */
+#define CONFIG_CROS_EC		/* CROS_EC protocol */
+#define CONFIG_CROS_EC_SPI		/* Support CROS_EC over SPI */
+#define CONFIG_CROS_EC_I2C		/* Support CROS_EC over I2C */
+#define CONFIG_CROS_EC_KEYB	/* CROS_EC keyboard input */
+#define CONFIG_CMD_CROS_EC
+#define CONFIG_KEYBOARD
+
+/* Console configuration */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define EXYNOS_DEVICE_SETTINGS \
+		"stdin=serial,cros-ec-keyb\0" \
+		"stdout=serial,lcd\0" \
+		"stderr=serial,lcd\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	EXYNOS_DEVICE_SETTINGS
+
+/* SD/MMC configuration */
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC
+#define CONFIG_SDHCI
+#define CONFIG_S5P_SDHCI
+#define CONFIG_DWMMC
+#define CONFIG_EXYNOS_DWMMC
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_SKIP_LOWLEVEL_INIT
+
+/* PWM */
+#define CONFIG_PWM
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Command definition*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_HASH
+
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+/* Thermal Management Unit */
+#define CONFIG_EXYNOS_TMU
+#define CONFIG_CMD_DTT
+#define CONFIG_TMU_CMD_DTT
+
+/* USB */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_EXYNOS
+#define CONFIG_USB_STORAGE
+
+/* USB boot mode */
+#define CONFIG_USB_BOOTING
+#define EXYNOS_COPY_USB_FNPTR_ADDR	0x02020070
+#define EXYNOS_USB_SECONDARY_BOOT	0xfeed0002
+#define EXYNOS_IRAM_SECONDARY_BASE	0x02020018
+
+/* TPM */
+#define CONFIG_TPM
+#define CONFIG_CMD_TPM
+#define CONFIG_TPM_TIS_I2C
+#define CONFIG_TPM_TIS_I2C_BUS_NUMBER	3
+#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
+
+/* MMC SPL */
+#define CONFIG_SPL
+#define COPY_BL2_FNPTR_ADDR	0x02020030
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+
+/* specific .lds file */
+#define CONFIG_SPL_LDSCRIPT	"board/samsung/common/exynos-uboot-spl.lds"
+#define CONFIG_SPL_MAX_FOOTPRINT	(14 * 1024)
+
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5E00000)
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
+
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_RD_LVL
+
+#define CONFIG_NR_DRAM_BANKS	8
+#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
+#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
+#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
+#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_5		(CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_5_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_6		(CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_6_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_7		(CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_7_SIZE	SDRAM_BANK_SIZE
+#define PHYS_SDRAM_8		(CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
+#define PHYS_SDRAM_8_SIZE	SDRAM_BANK_SIZE
+
+#define CONFIG_SYS_MONITOR_BASE	0x00000000
+
+/* FLASH and environment organization */

include/configs/exynos5-dt.h line 208

Quoted 10 lines
include/configs/exynos5-dt.h new file +10 -0
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_SYS_MMC_ENV_DEV		0
+
+#define CONFIG_SECURE_BL1_ONLY
+
+/* Secure FW size configuration */
+#ifdef	CONFIG_SECURE_BL1_ONLY
+#define	CONFIG_SEC_FW_SIZE	(8 << 10) /* 8KB */

please use space.

include/configs/exynos5-dt.h line 210

Quoted 2 lines
include/configs/exynos5-dt.h new file +2 -0
+#else
+#define	CONFIG_SEC_FW_SIZE	0

ditto.

Quoted 504 lines
include/configs/exynos5-dt.h new file +90 -0
+#endif
+
+/* Configuration of BL1, BL2, ENV Blocks on mmc */
+#define CONFIG_RES_BLOCK_SIZE	(512)
+#define CONFIG_BL1_SIZE	(16 << 10) /*16 K reserved for BL1*/
+#define	CONFIG_BL2_SIZE	(512UL << 10UL)	/* 512 KB */
+#define CONFIG_ENV_SIZE	(16 << 10)	/* 16 KB */
+
+#define CONFIG_BL1_OFFSET	(CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
+#define CONFIG_BL2_OFFSET	(CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
+#define CONFIG_ENV_OFFSET	(CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
+
+/* U-boot copy size from boot Media to DRAM.*/
+#define BL2_START_OFFSET	(CONFIG_BL2_OFFSET/512)
+#define BL2_SIZE_BLOC_COUNT	(CONFIG_BL2_SIZE/512)
+
+#define CONFIG_SPI_BOOTING
+#define EXYNOS_COPY_SPI_FNPTR_ADDR	0x02020058
+#define SPI_FLASH_UBOOT_POS		(CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_PART
+#define CONFIG_PARTITION_UUIDS
+
+/* I2C */
+#define CONFIG_SYS_I2C_INIT_BOARD
+#define CONFIG_HARD_I2C
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_SPEED	100000		/* 100 Kbps */
+#define CONFIG_DRIVER_S3C24X0_I2C
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SLAVE    0x0
+#define CONFIG_I2C_EDID
+
+/* SPI */
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SPI_FLASH
+
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_EXYNOS_SPI
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+#define CONFIG_SPI_FLASH_WINBOND
+#define CONFIG_SPI_FLASH_GIGADEVICE
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+#define CONFIG_SF_DEFAULT_SPEED		50000000
+#define EXYNOS5_SPI_NUM_CONTROLLERS	5
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_MODE	SPI_MODE_0
+#define CONFIG_ENV_SECT_SIZE	CONFIG_ENV_SIZE
+#define CONFIG_ENV_SPI_BUS	1
+#define CONFIG_ENV_SPI_MAX_HZ	50000000
+#endif
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+
+/* Ethernet Controllor Driver */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_BASE		0x5000000
+#define CONFIG_SMC911X_16_BIT
+#define CONFIG_ENV_SROM_BANK		1
+#endif /*CONFIG_CMD_NET*/
+
+/* Enable PXE Support */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_PXE
+#define CONFIG_MENU
+#endif
+
+/* Enable devicetree support */
+#define CONFIG_OF_LIBFDT
+
+/* SHA hashing */
+#define CONFIG_CMD_HASH
+#define CONFIG_HASH_VERIFY
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+
+/* Enable Time Command */
+#define CONFIG_CMD_TIME
+
+#define CONFIG_CMD_BOOTZ
+
+#endif	/* __CONFIG_H */
include/configs/exynos5250-dt.h +8 -311
index 1ed36dd..14522d3 100644
@@ -1,3 +1,4 @@
+
 /*
  * Copyright (C) 2012 Samsung Electronics
  *
@@ -6,326 +7,35 @@
  * SPDX-License-Identifier:	GPL-2.0+
  */
 
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_SAMSUNG			/* in a SAMSUNG core */
-#define CONFIG_S5P			/* S5P Family */
-#define CONFIG_EXYNOS5			/* which is in a Exynos5 Family */
-#define CONFIG_EXYNOS5250
-
-#include <asm/arch/cpu.h>		/* get chip and board defs */
-
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_BOARD_COMMON
-#define CONFIG_ARCH_EARLY_INIT_R
+#ifndef __CONFIG_5250_H
+#define __CONFIG_5250_H
 
-/* Enable fdt support for Exynos5250 */
-#define CONFIG_OF_CONTROL
-#define CONFIG_OF_SEPARATE
+#include <configs/exynos5-dt.h>
 
-/* Allow tracing to be enabled */
-#define CONFIG_TRACE
-#define CONFIG_CMD_TRACE
-#define CONFIG_TRACE_BUFFER_SIZE	(16 << 20)
-#define CONFIG_TRACE_EARLY_SIZE		(8 << 20)
-#define CONFIG_TRACE_EARLY
-#define CONFIG_TRACE_EARLY_ADDR		0x50000000
-
-/* Keep L2 Cache Disabled */
-#define CONFIG_SYS_DCACHE_OFF
-
-/* Enable ACE acceleration for SHA1 and SHA256 */
-#define CONFIG_EXYNOS_ACE_SHA
-#define CONFIG_SHA_HW_ACCEL
+#define CONFIG_EXYNOS5250
 
 #define CONFIG_SYS_SDRAM_BASE		0x40000000
 #define CONFIG_SYS_TEXT_BASE		0x43E00000
 
-/* input clock of PLL: SMDK5250 has 24MHz input clock */
-#define CONFIG_SYS_CLK_FREQ		24000000
-
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_INITRD_TAG
-#define CONFIG_CMDLINE_EDITING
-
 /* MACH_TYPE_SMDK5250 macro will be removed once added to mach-types */
 #define MACH_TYPE_SMDK5250		3774
 #define CONFIG_MACH_TYPE		MACH_TYPE_SMDK5250
 
-/* Power Down Modes */
-#define S5P_CHECK_SLEEP			0x00000BAD
-#define S5P_CHECK_DIDLE			0xBAD00000
-#define S5P_CHECK_LPA			0xABAD0000
-
-/* Offset for inform registers */
-#define INFORM0_OFFSET			0x800
-#define INFORM1_OFFSET			0x804
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (4 << 20))
-
-/* select serial console configuration */
-#define CONFIG_BAUDRATE			115200
-#define EXYNOS5_DEFAULT_UART_OFFSET	0x010000
-#define CONFIG_SILENT_CONSOLE
-
-/* Enable keyboard */
-#define CONFIG_CROS_EC		/* CROS_EC protocol */
-#define CONFIG_CROS_EC_SPI		/* Support CROS_EC over SPI */
-#define CONFIG_CROS_EC_I2C		/* Support CROS_EC over I2C */
-#define CONFIG_CROS_EC_KEYB	/* CROS_EC keyboard input */
-#define CONFIG_CMD_CROS_EC
-#define CONFIG_KEYBOARD
-
-/* Console configuration */
-#define CONFIG_CONSOLE_MUX
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#define EXYNOS_DEVICE_SETTINGS \
-		"stdin=serial,cros-ec-keyb\0" \
-		"stdout=serial,lcd\0" \
-		"stderr=serial,lcd\0"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	EXYNOS_DEVICE_SETTINGS
-
-/* SD/MMC configuration */
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_SDHCI
-#define CONFIG_S5P_SDHCI
-#define CONFIG_DWMMC
-#define CONFIG_EXYNOS_DWMMC
-#define CONFIG_SUPPORT_EMMC_BOOT
-
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-/* PWM */
-#define CONFIG_PWM
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* Command definition*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_HASH
-
-#define CONFIG_BOOTDELAY		3
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-
-/* Thermal Management Unit */
-#define CONFIG_EXYNOS_TMU
-#define CONFIG_CMD_DTT
-#define CONFIG_TMU_CMD_DTT
-
-/* USB */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_EXYNOS
-#define CONFIG_USB_STORAGE
-
-/* USB boot mode */
-#define CONFIG_USB_BOOTING
-#define EXYNOS_COPY_USB_FNPTR_ADDR	0x02020070
-#define EXYNOS_USB_SECONDARY_BOOT	0xfeed0002
-#define EXYNOS_IRAM_SECONDARY_BASE	0x02020018
-
-/* TPM */
-#define CONFIG_TPM
-#define CONFIG_CMD_TPM
-#define CONFIG_TPM_TIS_I2C
-#define CONFIG_TPM_TIS_I2C_BUS_NUMBER	3
-#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR	0x20
-
-/* MMC SPL */
-#define CONFIG_EXYNOS_SPL
-#define CONFIG_SPL
-#define COPY_BL2_FNPTR_ADDR	0x02020030
-
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-
-/* specific .lds file */
-#define CONFIG_SPL_LDSCRIPT	"board/samsung/common/exynos-uboot-spl.lds"
 #define CONFIG_SPL_TEXT_BASE	0x02023400
-#define CONFIG_SPL_MAX_FOOTPRINT	(14 * 1024)
 
 #define CONFIG_BOOTCOMMAND	"mmc read 40007000 451 2000; bootm 40007000"
 
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
 #define CONFIG_SYS_PROMPT		"SMDK5250 # "
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE		384	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
-#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-/* memtest works on */
-#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_SDRAM_BASE + 0x5E00000)
-#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x3E00000)
-
-#define CONFIG_SYS_HZ			1000
-
-#define CONFIG_RD_LVL
-
-#define CONFIG_NR_DRAM_BANKS	8
-#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
-#define PHYS_SDRAM_1		CONFIG_SYS_SDRAM_BASE
-#define PHYS_SDRAM_1_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_2		(CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
-#define PHYS_SDRAM_2_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_3		(CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_3_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_4		(CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_4_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_5		(CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_5_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_6		(CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_6_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_7		(CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_7_SIZE	SDRAM_BANK_SIZE
-#define PHYS_SDRAM_8		(CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
-#define PHYS_SDRAM_8_SIZE	SDRAM_BANK_SIZE
-
-#define CONFIG_SYS_MONITOR_BASE	0x00000000
-
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH
-#undef CONFIG_CMD_IMLS
-#define CONFIG_IDENT_STRING		" for SMDK5250"
-
-#define CONFIG_SYS_MMC_ENV_DEV		0
-
-#define CONFIG_SECURE_BL1_ONLY
-
-/* Secure FW size configuration */
-#ifdef	CONFIG_SECURE_BL1_ONLY
-#define	CONFIG_SEC_FW_SIZE		(8 << 10)	/* 8KB */
-#else
-#define	CONFIG_SEC_FW_SIZE		0
-#endif
-
-/* Configuration of BL1, BL2, ENV Blocks on mmc */
-#define CONFIG_RES_BLOCK_SIZE	(512)
-#define CONFIG_BL1_SIZE		(16 << 10) /*16 K reserved for BL1*/
-#define	CONFIG_BL2_SIZE		(512UL << 10UL)	/* 512 KB */
-#define CONFIG_ENV_SIZE		(16 << 10)	/* 16 KB */
-
-#define CONFIG_BL1_OFFSET	(CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
-#define CONFIG_BL2_OFFSET	(CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
-#define CONFIG_ENV_OFFSET	(CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
-
-/* U-boot copy size from boot Media to DRAM.*/
-#define BL2_START_OFFSET	(CONFIG_BL2_OFFSET/512)
-#define BL2_SIZE_BLOC_COUNT	(CONFIG_BL2_SIZE/512)
-
-#define CONFIG_SPI_BOOTING
-#define EXYNOS_COPY_SPI_FNPTR_ADDR	0x02020058
-#define SPI_FLASH_UBOOT_POS		(CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
-
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-#define CONFIG_CMD_PART
-#define CONFIG_PARTITION_UUIDS
-
 
 #define CONFIG_IRAM_STACK	0x02050000
 
 #define CONFIG_SYS_INIT_SP_ADDR	CONFIG_IRAM_STACK
 
-/* I2C */
-#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_HARD_I2C
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED	100000		/* 100 Kbps */
-#define CONFIG_DRIVER_S3C24X0_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_MAX_I2C_NUM	8
-#define CONFIG_SYS_I2C_SLAVE    0x0
-#define CONFIG_I2C_EDID
-
 /* PMIC */
-#define CONFIG_PMIC
-#define CONFIG_PMIC_I2C
 #define CONFIG_PMIC_MAX77686
 
-/* SPI */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SPI_FLASH
-
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_EXYNOS_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_SPI_FLASH_WINBOND
-#define CONFIG_SPI_FLASH_GIGADEVICE
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED		50000000
-#define EXYNOS5_SPI_NUM_CONTROLLERS	5
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_MODE	SPI_MODE_0
-#define CONFIG_ENV_SECT_SIZE	CONFIG_ENV_SIZE
-#define CONFIG_ENV_SPI_BUS	1
-#define CONFIG_ENV_SPI_MAX_HZ	50000000
-#endif
-
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_MAX77686
-
-/* SPI */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SPI_FLASH
-
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_EXYNOS_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_SPI_FLASH_WINBOND
-#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED		50000000
-#define EXYNOS5_SPI_NUM_CONTROLLERS	5
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_MODE	SPI_MODE_0
-#define CONFIG_ENV_SECT_SIZE	CONFIG_ENV_SIZE
-#define CONFIG_ENV_SPI_BUS	1
-#define CONFIG_ENV_SPI_MAX_HZ	50000000
-#endif
-
-/* Ethernet Controllor Driver */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_SMC911X
-#define CONFIG_SMC911X_BASE		0x5000000
-#define CONFIG_SMC911X_16_BIT
-#define CONFIG_ENV_SROM_BANK		1
-#endif /*CONFIG_CMD_NET*/
-
-/* Enable PXE Support */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_PXE
-#define CONFIG_MENU
-#endif
+/* I2C */
+#define CONFIG_MAX_I2C_NUM	8
 
 /* Sound */
 #define CONFIG_CMD_SOUND
@@ -336,15 +46,6 @@
 #define CONFIG_SOUND_WM8994
 #endif
 
-/* Enable devicetree support */
-#define CONFIG_OF_LIBFDT
-
-/* SHA hashing */
-#define CONFIG_CMD_HASH
-#define CONFIG_HASH_VERIFY
-#define CONFIG_SHA1
-#define CONFIG_SHA256
-
 /* Display */
 #define CONFIG_LCD
 #ifdef CONFIG_LCD
@@ -354,8 +55,4 @@
 #define LCD_YRES			1600
 #define LCD_BPP			LCD_COLOR16
 #endif
-
-/* Enable Time Command */
-#define CONFIG_CMD_TIME
-
-#endif	/* __CONFIG_H */
+#endif  /* __CONFIG_5250_H */
include/configs/smdk5420.h new file +39 -0
new file mode 100644
index 0000000..e580049
@@ -0,0 +1,49 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ *
+ * Configuration settings for the SAMSUNG EXYNOS5420 board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_5420_H
+#define __CONFIG_5420_H
+
+#include <configs/exynos5-dt.h>
+
+#define CONFIG_EXYNOS5420		/* which is in a Exynos5 Family */
+#define CONFIG_SMDK5420			/* which is in a SMDK5420 */
+
+#undef CONFIG_DEFAULT_DEVICE_TREE
+#define CONFIG_DEFAULT_DEVICE_TREE	exynos5420-smdk5420
+
+#define CONFIG_ARCH_DEVICE_TREE		exynos5420
+
+#define CONFIG_SYS_SDRAM_BASE		0x20000000
+#define CONFIG_SYS_TEXT_BASE		0x23E00000
+
+#define CONFIG_BOARD_REV_GPIO_COUNT	2
+
+/* MACH_TYPE_SMDK5420 macro will be removed once added to mach-types */
+#define MACH_TYPE_SMDK5420		8002 /* Temporary number */
+#define CONFIG_MACH_TYPE		MACH_TYPE_SMDK5420
+
+/* select serial console configuration */
+#define CONFIG_SERIAL3			/* use SERIAL 3 */
+
+#define CONFIG_SPL_TEXT_BASE	0x02024400
+#define CONFIG_BOOTCOMMAND	"mmc read 20007000 451 2000; bootm 20007000"
+
+#define CONFIG_SYS_PROMPT		"SMDK5420 # "
+#define CONFIG_IDENT_STRING		" for SMDK5420"
+

include/configs/smdk5420.h line 49

Quoted 10 lines
include/configs/smdk5420.h new file +10 -0
+#define CONFIG_IRAM_TOP		0x02074000
+/*
+ * Put the initial stack pointer 1KB below this to allow room for the
+ * SPL marker. This value is arbitrary, but gd_t is placed starting here.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_IRAM_TOP - 0x800)
+
+#define CONFIG_MAX_I2C_NUM	11
+
+#endif	/* __CONFIG_5420_H */

Thanks,
Minkyu Kang.

#17 lore raw

PATCH v8 9/9 SPL: EXYNOS: Prepare for variable size SPL support

In reply to Rajeshwari S Shinde

When variable size SPL is used, the BL1 expects the SPL to be encapsulated differently: instead of putting the checksum at a fixed offset in the SPL blob, prepend the blob with a header including the size and the checksum.

The enhancements include
- adding a command line option, '--vs' to indicate the need for the variable size encapsulation
- padding the fixed size encapsulated blob with 0xff instead of random memory contents
- do not silently truncate the input file, report error instead
- no need to explicitly closing files/freeing memory, this all happens on exit; removing cleanups it makes code clearer
- profuse commenting
- modify Makefile to allow enabling the new feature per board

---
Changes in V2:
- None
Changes in V3:
- None
Changes in V4:
- Created a common exynos5-dt.h
Changes in V5:
- None
Changes in V6:
- None.
Changes in V7:
- None.
Changes in V8:
- None

 include/configs/smdk5420.h |   7 ++
 spl/Makefile               |   7 +-
 tools/mkexynosspl.c        | 167 +++++++++++++++++++++++++++++++++------------
 3 files changed, 137 insertions(+), 44 deletions(-)
include/configs/smdk5420.h +7 -0
index e580049..447f8e5 100644
@@ -19,6 +19,8 @@
 
 #define CONFIG_ARCH_DEVICE_TREE		exynos5420
 
+#define CONFIG_VAR_SIZE_SPL
+
 #define CONFIG_SYS_SDRAM_BASE		0x20000000
 #define CONFIG_SYS_TEXT_BASE		0x23E00000
 
@@ -31,7 +33,12 @@
 /* select serial console configuration */
 #define CONFIG_SERIAL3			/* use SERIAL 3 */
 
+#ifdef CONFIG_VAR_SIZE_SPL
+#define CONFIG_SPL_TEXT_BASE		0x02024410
+#else
 #define CONFIG_SPL_TEXT_BASE	0x02024400
+#endif
+
 #define CONFIG_BOOTCOMMAND	"mmc read 20007000 451 2000; bootm 20007000"
 
 #define CONFIG_SYS_PROMPT		"SMDK5420 # "
spl/Makefile +6 -1
index b366ac2..d5f6ae8 100644
@@ -184,8 +184,13 @@ endif
 all:	$(ALL-y)
 
 ifdef CONFIG_SAMSUNG
+ifdef CONFIG_VAR_SIZE_SPL
+VAR_SIZE_PARAM = --vs
+else
+VAR_SIZE_PARAM =
+endif
 $(obj)$(BOARD)-spl.bin: $(obj)u-boot-spl.bin
-	$(OBJTREE)/tools/mk$(BOARD)spl \
+	$(OBJTREE)/tools/mk$(BOARD)spl $(VAR_SIZE_PARAM) \
 		$(obj)u-boot-spl.bin $(obj)$(BOARD)-spl.bin
 endif
 
tools/mkexynosspl.c +124 -43

217 lines not on this page · raw message

Signature · 1 line
1.7.12.4
#18 lore raw

v8 cover EXYNOS5420: Add SMDK5420 board support

In reply to Rajeshwari S Shinde

Hi Minkyu Kang.

Please do let me know if any comments or can we get this merged?

Quoted 100 lines · Rajeshwari S Shinde

This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.

Changes in V2:
- Corrected a compilation issue for SMDK5420.

Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.

Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.

Changes in V5:
- Moved functions board_mmc_init and board_eth_init to common/board.c in case of device tree support.

Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU to arch/arm dwmmc.h

Changes in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.

Changes in V8:
- corrected the if loops with if conditions of pro_id and cpu_id.

Rajeshwari S Shinde (9):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL support

 arch/arm/cpu/armv7/exynos/clock.c              | 258 ++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++-
 arch/arm/cpu/armv7/exynos/dmc_common.c         |  10 +-
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c      | 421 +++++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 738 +++++++++++++++++++------
 arch/arm/cpu/armv7/exynos/pinmux.c             | 260 ++++++++-
 arch/arm/dts/exynos5.dtsi                      | 198 +++++++
 arch/arm/dts/exynos5250.dtsi                   | 196 +------
 arch/arm/dts/exynos5420.dtsi                   |  70 +++
 arch/arm/include/asm/arch-exynos/board.h       |  17 +
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++++
 arch/arm/include/asm/arch-exynos/cpu.h         |  51 +-
 arch/arm/include/asm/arch-exynos/dmc.h         | 123 +++--
 arch/arm/include/asm/arch-exynos/gpio.h        | 143 ++++-
 arch/arm/include/asm/arch-exynos/periph.h      |   3 +
 board/samsung/common/Makefile                  |   4 +
 board/samsung/common/board.c                   | 407 ++++++++++++++
 board/samsung/dts/exynos5420-smdk5420.dts      | 169 ++++++
 board/samsung/smdk5250/exynos5-dt.c            | 361 +-----------
 board/samsung/smdk5250/smdk5250.c              | 182 +-----
 board/samsung/smdk5420/Makefile                |  34 ++
 board/samsung/smdk5420/smdk5420.c              | 159 ++++++
 board/samsung/smdk5420/smdk5420_spl.c          |  52 ++
 boards.cfg                                     |   1 +
 include/configs/arndale.h                      |   1 +
 include/configs/exynos5-dt.h                   | 300 ++++++++++
 include/configs/exynos5250-dt.h                | 316 +----------
 include/configs/smdk5420.h                     |  56 ++
 spl/Makefile                                   |   7 +-
 tools/Makefile                                 |   3 +-
 tools/mkexynosspl.c                            | 167 ++++--
 33 files changed, 4227 insertions(+), 1344 deletions(-)
 create mode 100644 arch/arm/dts/exynos5.dtsi
 create mode 100644 arch/arm/dts/exynos5420.dtsi
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c
 create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h

--
1.7.12.4

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Signature · 2 lines
Regards,
Rajeshwari Shinde
#19 lore raw

v8 cover EXYNOS5420: Add SMDK5420 board support

Quoted 109 lines · Rajeshwari Birje

Hi Minkyu Kang.

Please do let me know if any comments or can we get this merged?

Quoted 100 lines · Rajeshwari S Shinde

This patch adds basic board support for SMDK5420 board. These patches are tested for booting fine on EVT1 SMDK5420.

Changes in V2:
- Corrected a compilation issue for SMDK5420.

Changes in V3:
- Add patch to support variable size SPL support
- Add patch to disable SMU for eMMC.

Changes in V4:
- Added check for MAX77686 pmic compilation.
- Added correct calculation of gpio based addresses.
- Rebased on the latest u-boot code.
- Removed patches for UART and TZPC changes as they were not needed.
- Added flag to disable SMU for eMMC.

Changes in V5:
- Moved functions board_mmc_init and board_eth_init to common/board.c in case of device tree support.

Changes in V6:
- Rebased on the latest mainline branch.
- Moved the definitions for SMU to arch/arm dwmmc.h

Changes in V7:
- Removed below patch as it is already merged "DWMMC: SMDK5420: Disable SMU for eMMC"
- Corrected the multi line comments and removal of blank spaces and lines.
- Corrected the license.

Changes in V8:
- corrected the if loops with if conditions of pro_id and cpu_id.

Rajeshwari S Shinde (9):
EXYNOS5: Create a common board file
Exynos5420: Add base addresses for 5420
Exynos5420: Add clock initialization for 5420
Exynos5420: Add DDR3 initialization for 5420
Exynos5420: Add support for 5420 in pinmux and gpio
Exynos5420: Add base patch for SMDK5420
DTS: Add dts support for SMDK5420
Config: Add initial config for SMDK5420
SPL: EXYNOS: Prepare for variable size SPL support

 arch/arm/cpu/armv7/exynos/clock.c              | 258 ++++++++-
 arch/arm/cpu/armv7/exynos/clock_init.h         |  17 +
 arch/arm/cpu/armv7/exynos/clock_init_exynos5.c | 352 +++++++++++-
 arch/arm/cpu/armv7/exynos/dmc_common.c         |  10 +-
 arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c      | 421 +++++++++++++-
 arch/arm/cpu/armv7/exynos/exynos5_setup.h      | 738 +++++++++++++++++++------
 arch/arm/cpu/armv7/exynos/pinmux.c             | 260 ++++++++-
 arch/arm/dts/exynos5.dtsi                      | 198 +++++++
 arch/arm/dts/exynos5250.dtsi                   | 196 +------
 arch/arm/dts/exynos5420.dtsi                   |  70 +++
 arch/arm/include/asm/arch-exynos/board.h       |  17 +
 arch/arm/include/asm/arch-exynos/clk.h         |   1 +
 arch/arm/include/asm/arch-exynos/clock.h       | 494 +++++++++++++++++
 arch/arm/include/asm/arch-exynos/cpu.h         |  51 +-
 arch/arm/include/asm/arch-exynos/dmc.h         | 123 +++--
 arch/arm/include/asm/arch-exynos/gpio.h        | 143 ++++-
 arch/arm/include/asm/arch-exynos/periph.h      |   3 +
 board/samsung/common/Makefile                  |   4 +
 board/samsung/common/board.c                   | 407 ++++++++++++++
 board/samsung/dts/exynos5420-smdk5420.dts      | 169 ++++++
 board/samsung/smdk5250/exynos5-dt.c            | 361 +-----------
 board/samsung/smdk5250/smdk5250.c              | 182 +-----
 board/samsung/smdk5420/Makefile                |  34 ++
 board/samsung/smdk5420/smdk5420.c              | 159 ++++++
 board/samsung/smdk5420/smdk5420_spl.c          |  52 ++
 boards.cfg                                     |   1 +
 include/configs/arndale.h                      |   1 +
 include/configs/exynos5-dt.h                   | 300 ++++++++++
 include/configs/exynos5250-dt.h                | 316 +----------
 include/configs/smdk5420.h                     |  56 ++
 spl/Makefile                                   |   7 +-
 tools/Makefile                                 |   3 +-
 tools/mkexynosspl.c                            | 167 ++++--
 33 files changed, 4227 insertions(+), 1344 deletions(-)
 create mode 100644 arch/arm/dts/exynos5.dtsi
 create mode 100644 arch/arm/dts/exynos5420.dtsi
 create mode 100644 arch/arm/include/asm/arch-exynos/board.h
 create mode 100644 board/samsung/common/board.c
 create mode 100644 board/samsung/dts/exynos5420-smdk5420.dts
 create mode 100644 board/samsung/smdk5420/Makefile
 create mode 100644 board/samsung/smdk5420/smdk5420.c
 create mode 100644 board/samsung/smdk5420/smdk5420_spl.c
 create mode 100644 include/configs/exynos5-dt.h
 create mode 100644 include/configs/smdk5420.h

--
1.7.12.4

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

I already sent comments on your patches. but, it does not reached at mailing list. I don't know why.
Anyway sorry, I'll resend comments.

Thanks,
Minkyu Kang.